Discontinuous Disturbance (Click) EN :2006+A1:2009+A2:2011 Clause N/A** Radiated Emission, 30MHz to 1000MHz

Transcription

1

2 Reference No.: WTN13F E Page 2 of 40 1 Test Summary Test Item Mains Terminal Disturbance Voltage, 148.5kHz to 30MHz Disturbance Power, 30MHz to 300MHz EMISSION Test Standard Class / Severity Result EN :2006+A1:2009+A2:2011 Clause Pass EN :2006+A1:2009+A2:2011 Clause Pass Discontinuous Disturbance (Click) EN :2006+A1:2009+A2:2011 Clause N/A** Radiated Emission, 30MHz to 1000MHz EN :2006+A1:2009+A2 :2011 Clause N/A Harmonic Current emission EN :2006+A1:2009+A2:2009 Class A Pass Voltage Fluctuation and Flicker EN :2008 Clause 5 Pass IMMUNITY(EN :1997+A1:2001+A2:2008) Test Item Test Method Class / Severity Electrostatic Discharge(ESD) IEC :2008 Radio-frequency electromagnetic fields (80MHz to 1GHz) IEC :2010 Electrical Fast Transients (EFT) IEC :2012 Surge IEC :2005 Injected Currents, 0.15MHz to 230MHz IEC : Kv Contact 8 Kv Air 3V/m, 80%, 1kHz, Amp. Mod. AC 1.0Kv DC 0.5Kv 1Kv D.M. 2Kv C.M. 3Vr.m.s.(emf), 80%, 1kHz Amp. Mod. 0 % UT* for 0.5per Performance Criteria B A B B A Result Pass N/A Pass Pass Pass Pass Voltage Dips and Interruptions IEC : % UT* for 10per C Pass 70 % UT* for 25per Pass Remark: Pass Fail N/A A.M Test item meets the requirement Test item does not meet the requirement Test case does not apply to the test object Amplitude Modulation Differential Mode Common Mode * U T is the nominal supply voltage ** According to the electrical characteristics and usage of the equipment, the EUT does not produce discontinuous radio interference voltages on AC Mains. Therefore this test item has been skipped.

3 Reference No.: WTN13F E Page 3 of 40 2 Contents Page COVER PAGE 1 1 TEST SUMMARY CONTENTS GENERAL INFORMATION GENERAL DESCRIPTION OF E.U.T DETAILS OF E.U.T DESCRIPTION OF SUPPORT UNITS STANDARDS APPLICABLE FOR TESTING TEST FACILITY SUBCONTRACTED ABNORMALITIES FROM STANDARD CONDITIONS EQUIPMENT USED DURING TEST MEASUREMENT UNCERTAINTY EMISSION TEST RESULTS MAINS TERMINALS DISTURBANCE VOLTAGE, 148.5KHZ TO 30MHZ E.U.T. Operation Block Diagram of Test Setup Measurement Data Mains Terminals Disturbance Voltage Test Data DISTURBANCE POWER, 30MHZ TO 300MHZ E.U.T. Operation Block Diagram of Test Setup Measurement Data Disturbance Power Test Results on AC Line(BST-917II) Disturbance Power Test Results on AC Line(BST-918II) HARMONICS CURRENT EMISSION E.U.T. Operation Block Diagram of Setup Harmonic Current Emission Test Data VOLTAGE FLUCTUATION AND FLICKER E.U.T. Operation Block Diagram of Setup Voltage Fluctuation and Flicker Test Data IMMUNITY TEST RESULTS PERFORMANCE CRITERIA ELECTROSTATIC DISCHARGE (ESD) E.U.T. Operation Block Diagram of Setup Direct Discharge Test Results Indirect Discharge Test Results ELECTRICAL FAST TRANSIENTS (EFT) E.U.T. Operation Block Diagram of Setup Test Results SURGE E.U.T. Operation Block Diagram of Setup Test Results INJECTED CURRENTS IMMUNITY, 0.15MHZ TO 230MHZ... 32

4 Reference No.: WTN13F E Page 4 of E.U.T. Operation Block Diagram of Setup Test Results VOLTAGE DIPS AND INTERRUPTIONS E.U.T. Operation Block Diagram of Setup Test Results PHOTOGRAPHS TEST SETUP PHOTOGRAPH MAINS TERMINAL DISTURBANCE VOLTAGE TEST SETUP PHOTOGRAPH DISTURBANCE POWER TEST SETUP PHOTOGRAPH HARMONIC CURRENT AND VOLTAGE FLUCTUATION AND FLICKER TEST SETUP PHOTOGRAPH ESD IMMUNITY TEST SETUP PHOTOGRAPH EFT IMMUNITY TEST SETUP PHOTOGRAPH SURGE IMMUNITY TEST SETUP PHOTOGRAPH INJECTED CURRENTS IMMUNITY TEST SETUP PHOTOGRAPH VOLTAGE DIPS AND INTERRUPTIONS IMMUNITY TEST SETUP PHOTOGRAPHS CONSTRUCTIONAL DETAILS EUT FRONT VIEW(BST-917II) EUT FRONT VIEW(BST-918II)... 40

5 Reference No.: WTN13F E Page 5 of 40 3 General Information 3.1 General Description of E.U.T. Product Name... : Intelligent electronical toilets Model No.... : BST-917I, BST-917II, BST-918I, BST-918II Remark... : The 917 series models have the same electric circuit, the 918 series models have the same electric circuit, the models with II have the remote control function, while other models with I have no this function,model BST-917II and model BST-918II have different control board, therefore the full EMC tests were performed on two representative models BST-917II, BST-918II. 3.2 Details of E.U.T. Technical Data... : V ~, 50/60Hz, 850W 3.3 Description of Support Units The EUT has been tested as an independent unit. BST-917II, BST-918II are the test samples. The DV,DP tests were performed in the condition of AC264V/50Hz input. The other tests were performed in the condition of AC230V/50Hz input. 3.4 Standards Applicable for Testing The tests were performed according to following standards: EN :2006+A1:2009 +A2:2011 EN :1997+A1:2001 +A2:2008 EN :2006 +A1:2009+A2:2009 EN :2008 Electromagnetic compatibility-requirements for household appliances, electric tools and similar apparatus-part 1:Emission Electromagnetic compatibility Requirements for household appliances, Part 2: Immunity Product family. Electromagnetic compatibility (EMC) -- Part 3-2: Limits - Limits for harmonic current emissions (equipment input current up to and including 16 A per phase). Electromagnetic compatibility (EMC) -- Part 3-3: Limits - Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current 16 A per phase and not subject to conditional connection.

6 Reference No.: WTN13F E Page 6 of Test Facility The test facility has a test site registered with the following organizations: IC Registration No.: 7760A Waltek Services (Shenzhen) Co., Ltd. has been registered and fully described in a report filed with the Industry Canada. The acceptance letter from the Industry Canada is maintained in our files. Registration 7760A, August 03, FCC Registration No.: Waltek Services (Shenzhen) Co., Ltd. has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. Registration , May 26, Subcontracted Whether parts of tests for the product have been subcontracted to other labs: Yes No If Yes, list the related test items and lab information: Test items:--- Lab information: Abnormalities from Standard Conditions None.

7 Reference No.: WTN13F E Page 7 of 40 4 Equipment Used during Test Mains Terminal Disturbance Voltage (Conducted Emission) Item Equipment Manufacturer Model No. Serial No. Calibration Status 1. EMI Test Receiver R&S ESCI Valid 2. LISN R&S ENV Valid 3. LISN SCHWARZBECK NSLK Valid 4. Cable HUBER+SUHNER CBL2-NN-3M Valid 5. Switch ESE RSU/M2 --- Valid Disturbance Power Item Equipment Manufacturer Model No. Serial No. Calibration Status 1. EMI Test Receiver R&S ESCI Valid 2. Absorbing Clamp LUTHI MDS Valid 3. Cable HUBER+SUHNER CBL2-NN-9M Valid 4. Switch ESE RSU/M2 --- Valid Discontinuous Disturbance Item Equipment Manufacturer Model No. Serial No. Calibration Status 1. Discontinues Disturbance Analyzer TESEQ DIA1512D Valid 2. LISN R&S ENV Valid Harmonics and Flicker Measuring System Item Equipment Manufacturer Model No. Serial No. Calibration Status 1. ESD Harmonics and Flicker Measuring System TESEQ PROFLINE A Item Equipment Manufacturer Model No. Serial No. Calibration Status Valid 1. ESD Simulator TESEQ NSG Valid EFT & Voltage Dips and Interruptions Item Equipment Manufacturer Model No. Serial No. Calibration Status 1. EMS test system TESEQ NSG Valid 2. Clamp TESEQ CDN Valid Surge Item Equipment Manufacturer Model No. Serial No. Calibration Status 1. Surge Simulator TESEQ NSG Valid Injected Currents Item Equipment Manufacturer Model No. Serial No. Calibration Status

8 Reference No.: WTN13F E Page 8 of Conducted Immunity test system TESEQ NSG Valid 2. CDN TESEQ M Valid 3. Clamp TESEQ KEMZ Valid 4.1 Measurement Uncertainty Test Item Frequency Range Uncertainty Note Conducted Emission 150kHz~30MHz 2.66dB (1) Disturbance Power 30MHz~300MHz 3.21dB (1) Radiated Emission 30MHz~1GHz 5.03dB (1) (1)This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2.

9 Reference No.: WTN13F E Page 9 of 40 5 Emission Test Results 5.1 Mains Terminals Disturbance Voltage, 148.5kHz to 30MHz Test Requirement... : EN Test Method... : EN Test Result... : Pass Frequency Range... : 148.5kHz to 30MHz Class/Severity... : Table 1 of EN E.U.T. Operation Operating Environment: Temperature... : 23.4 C Humidity... : 55.2%RH Atmospheric Pressure... : 101.2kPa EUT Operation: Input Voltage... : AC 264V/50Hz Operating Mode... : On mode Block Diagram of Test Setup The Mains Terminals Disturbance Voltage tests were performed in accordance with the EN

10 Reference No.: WTN13F E Page 10 of Measurement Data The maximised peak emissions from the EUT was scanned and measured for both the Live and Neutral Lines. Quasi-peak & average measurements were performed if peak emissions were within 6dB of the average limit line Mains Terminals Disturbance Voltage Test Data Live Line (BST-917II):

11 Reference No.: WTN13F E Page 11 of 40 Neutral Line (BST-917II):

12 Reference No.: WTN13F E Page 12 of 40 Live Line (BST-918II):

13 Reference No.: WTN13F E Page 13 of 40 Neutral Line (BST-918II):

14 Reference No.: WTN13F E Page 14 of Disturbance Power, 30MHz to 300MHz Test Requirement... : EN Test Method... : EN Test Result... : Pass Frequency Range... : 30MHz to 300MHz Class/Severity... : Table 2 of EN E.U.T. Operation Operating Environment: Temperature... : 23.4 C Humidity... : 55.2%RH Barometric Pressure... : 101.2kPa EUT Operation: Input Voltage... : AC 264V/50Hz Operating Mode... : On mode Block Diagram of Test Setup The Disturbance Power test was performed in accordance with the EN

15 Reference No.: WTN13F E Page 15 of Measurement Data Extending the cable to 6 meters, performed quasi-peak & average measurements since peak emissions from the EUT were detected within 15dB of the limit line. Average measurements were only performed if the quasi-peak measurements were within 15dB of the average limit line. According to the Clause , if both of the following conditions (1) and (2) are fulfilled: 1) all emission readings from the equipment under test shall be lower than the applicable limits (Table 2a) reduced by the margin (Table 2b); 2) the maximum clock frequency shall be less than 30 MHz. The Appliances are deemed to comply in the frequency range from 300 MHz to MHz Disturbance Power Test Results on AC Line(BST-917II)

16 Reference No.: WTN13F E Page 16 of Disturbance Power Test Results on AC Line(BST-918II)

17 Reference No.: WTN13F E Page 17 of Harmonics Current Emission Test Requirement... : EN Test Method... : EN Test Result... : Pass Class/Severity... : Class A E.U.T. Operation Operating Environment: Temperature... : 23.4 C Humidity... : 55.2%RH Barometric Pressure... : 101.2kPa EUT Operation: Input Voltage... : AC 230V/50Hz Operating Mode... : On mode Block Diagram of Setup The Harmonics Current emission test was performed in accordance with the EN

18 Reference No.: WTN13F E Page 18 of Harmonic Current Emission Test Data

19 Reference No.: WTN13F E Page 19 of 40

20 Reference No.: WTN13F E Page 20 of 40

21 Reference No.: WTN13F E Page 21 of 40

22 Reference No.: WTN13F E Page 22 of 40

23 Reference No.: WTN13F E Page 23 of 40

24 Reference No.: WTN13F E Page 24 of Voltage Fluctuation and Flicker Test Requirement... : EN Test Method... : EN Test Result... : Pass E.U.T. Operation Operating Environment: Temperature... : 23.4 C Humidity... : 55.2%RH Barometric Pressure... : 101.2kPa EUT Operation: Input Voltage... : AC 230V/50Hz Operating Mode... : On mode Block Diagram of Setup The Voltage Fluctuation and Flicker test was performed in accordance with the EN

25 Reference No.: WTN13F E Page 25 of Voltage Fluctuation and Flicker Test Data

26 Reference No.: WTN13F E Page 26 of 40

27 Reference No.: WTN13F E Page 27 of 40 6 Immunity Test Results 6.1 Performance Criteria Performance criterion A: The apparatus shall continue to operate as intended during the test. No degradation of performance or loss of function is allowed below a performance level (or permissible loss of performance) specified by the manufacturer, when the apparatus is used as intended. If the minimum performance level or the permissible performance loss is not specified by the manufacturer, then either of these may be derived from the product description and documentation, and from what the user may reasonably expect from the apparatus if used as intended. Performance criterion B: The apparatus shall continue to operate as intended after the test. No degradation of performance or loss of function is allowed below a performance level (or permissible loss of performance) specified by the manufacturer, when the apparatus is used as intended. During the test, degradation of performance is allowed, however, no change of actual operating state or stored data is allowed. If the minimum performance level or the permissible performance loss is not specified by the manufacturer, then either of these may be derived from the product description and documentation, and from what the user may reasonably expect from the apparatus if used as intended. Performance criterion C: Temporary loss of function is allowed, provided the function is selfrecoverable or can be restored by the operation of the controls, or by any operation specified in the instructions for use. For further details, please refer to EN Electrostatic Discharge (ESD) Test Requirement... : EN Test Method... : IEC Test Result... : Pass Discharge Impedance... : 330 / 150pF Discharge Voltage... : Air Discharge: ±8kV Contact Discharge: ±4kV HCP & VCP: ±4kV Polarity... : Positive & Negative Number of Discharge... : Minimum 10 times at each test point Discharge Mode... : Single Discharge Discharge Period... : 1 second minimum

28 Reference No.: WTN13F E Page 28 of E.U.T. Operation Operating Environment: Temperature... : 25.4 C Humidity... : 46.3%RH Barometric Pressure... : 101.2kPa EUT Operation: Input Voltage... : AC 230V/50Hz Operating Mode... : On mode Block Diagram of Setup The ESD test was performed in accordance with the IEC

29 Reference No.: WTN13F E Page 29 of Direct Discharge Test Results Observations: Test points: 1. All Exposed Surface & Seams; 2. All metallic part Direct Discharge Test Results Applied Voltage (kv) Performance Criterion Test Point Contact Discharge Air Discharge ±8 B 1 N/A Pass* ±4 B 2 Pass* N/A Remark: * During the test no deviation was detected to the selected operation mode(s) Indirect Discharge Test Results Observations: Test points: 1. All sides. Indirect Discharge Test Results Applied Voltage (kv) Performance Criterion Test Point Horizontal Coupling Vertical Coupling ±4 B 1 Pass* Pass* Remark: * During the test no deviation was detected to the selected operation mode(s) 6.3 Electrical Fast Transients (EFT) Test Requirement... : EN Test Method... : IEC Test Result... : Pass Test Level... : 1.0kV on AC Mains Polarity... : Positive & Negative Repetition Frequency... : 5kHz Burst Duration... : 300ms Test Duration... : 2 minutes per level & polarity

30 Reference No.: WTN13F E Page 30 of E.U.T. Operation Operating Environment: Temperature... : 25.4 C Humidity... : 46.3%RH Barometric Pressure... : 101.2kPa EUT Operation: Input Voltage... : AC 230V/50Hz Operating Mode... : On mode Block Diagram of Setup The Electrical Fast Transients Immunity test was performed in accordance with the IEC Test Results Test Port Test Level(kV) Performance Criterion Result Line-Neutral 1.0 B Pass* Remark: * During the test no deviation was detected to the selected operation mode(s)

31 Reference No.: WTN13F E Page 31 of Surge Test Requirement... : EN Test Method... : IEC Test Result... : Pass Test level... : 1kV Live to Neutral, 2kV Live to PE and Neutral to PE, Interval... : 60s between each surge No. of surges... : 5 positive at 90, 5 negative at E.U.T. Operation Operating Environment: Temperature... : 25.4 C Humidity... : 46.3%RH Barometric Pressure... : 101.2kPa EUT Operation: Input Voltage... : AC 230V/50Hz Operating Mode... : On mode Block Diagram of Setup The Surge Immunity test was performed in accordance with the IEC

32 Reference No.: WTN13F E Page 32 of Test Results Test Port Applied Voltage (kv) Performance criterion Result Between Phase And Phase 1 B N/A Between Live And Neutral 1 B Pass* Between Live And Earth 2 B N/A Between Neutral And Earth 2 B N/A Remark: * During the test no deviation was detected to the selected operation mode(s) 6.5 Injected Currents Immunity, 0.15MHz to 230MHz Test Requirement... : EN Test Method... : IEC Test Result... : Pass Frequency Range... : 0.15MHz to 230MHz Test level... : 3V r.m.s. (unmodulated emf into 150 ) Modulation... : 80%, 1kHz Amplitude Modulation E.U.T. Operation Operating Environment: Temperature... : 25.4 C Humidity... : 46.3%RH Barometric Pressure... : 101.2kPa EUT Operation: Input Voltage... : AC 230V/50Hz Operating Mode... : On mode

33 Reference No.: WTN13F E Page 33 of Block Diagram of Setup The Injected Currents Immunity test was performed in accordance with the IEC Test Results Frequency Line Test Level Modulation Step Size Dwell Time Performance Criterion Result 0.15MHz to 230MHz 2 Wire AC Supply Cables 3Vr.m.s. 80%, 1kHz Amp. Mod. 1% 1s A Pass* Remark: * During the test no deviation was detected to the selected operation mode(s)

34 Reference No.: WTN13F E Page 34 of Voltage Dips and Interruptions Test Requirement... EN Test Method... IEC Test Result... Pass Test Level(Voltage reduction) 0% & 40% &70 % of U T (Supply Voltage) No. of Dips / Interruptions... 1 per Level at 20ms intervals E.U.T. Operation Operating Environment: Temperature C Humidity %RH Barometric Pressure kPa EUT Operation: Input Voltage... AC 230V/50Hz Operating Mode... On mode Block Diagram of Setup The Voltage Dips and Interruptions Immunity test was performed in accordance with the IEC

35 Reference No.: WTN13F E Page 35 of Test Results Test Level in %U T Performance criterion 50Hz 60Hz Duration Result Duration Result 0 C 0.5 Pass* 0.5 Pass* 40 C 10 Pass* 12 Pass* 70 C 25 Pass* 30 Pass* Remark: * During the test no deviation was detected to the selected operation mode(s)

36 Reference No.: WTN13F E Page 36 of 40 7 Photographs Test Setup 7.1 Photograph Mains Terminal Disturbance Voltage Test Setup 7.2 Photograph Disturbance Power Test Setup

37 Reference No.: WTN13F E Page 37 of Photograph Harmonic Current and Voltage Fluctuation and Flicker Test Setup 7.4 Photograph ESD Immunity Test Setup

38 Reference No.: WTN13F E Page 38 of Photograph EFT Immunity Test Setup 7.6 Photograph Surge Immunity Test Setup

39 Reference No.: WTN13F E Page 39 of Photograph Injected Currents Immunity Test Setup 7.8 Photograph Voltage Dips and Interruptions Immunity Test Setup

40 Reference No.: WTN13F E Page 40 of 40 8 Photographs Constructional Details 8.1 EUT Front View(BST-917II) 8.2 EUT Front View(BST-918II) =================== End of Test Report ===================