Transducing electrical quantities Iskra MIS d.d. Measuring Transducers. Features
|
|
- Penelope Wilkerson
- 5 years ago
- Views:
Transcription
1 Measuring Transducers Transducing electrical quantities Iskra MIS d.d. Measuring Transducers Features AC, DC POWER SYSTEM MEASUREMENT MICROPROCESSOR CONTROL HOUSING FOR DIN RAIL MOUNTING IN COMPLIANCE WITH EN PROGRAMMABLE VOLTAGE RANGE PROGRAMMABLE CURRENT RANGE PROGRAMMABLE ANALOGUE SERIAL COMMUNICATION RS232/RS485 (OPTION) UP TO THREE ELECTRICALLY ISOLATED ANALOGUE S UNIVERSAL AUXILIARY POWER SUPPLY (OPTION) ACCURACY CLASS 0.5 (FREQUENCY TRANSDUCER 0.2) CURRENT S ELECTRICALLY ISOLATED FROM THE SYSTEM S, SERIAL COMMUNICATION, AUXILIARY POWER SUPPLY, CURRENT AND VOLTAGE S GALVANICALLY SEPARATED (SOME MODELS)
2 Description Digital technology, on which measuring transducers are built, enables them, with corresponding software, to adapt to different input and output quantities. Input quantities, for energy measuring transducers, of phase voltage can be set within the range from 50 to 500 V and currents from 0.2 to 5 A. Values of analogue outputs can also be set within the range from 1 to 20 ma for current and from 1 to 10 V for voltage. Input-output characteristics can be created with five breaking spots for unipolar and bipolar output signals. The accuracy class of measuring transducers is 0.5, except for frequency, where accuracy class is 0.2. MISET Software / Features - Configuring and setting software - Full instrument setup capability - Displays data in real time - Windows compatible - User friendly The above stated versions of measuring transducers can be provided with the RS232 or RS485 communication for connection to the network. The MODBUS communication protocol is used with bit rate from 1,200 to 115,200 bit/s. A measuring transducer with three electrically isolated bipolar analogue outputs (MI400) is the most capable version. Outputs can be software adapted to any measured quantity (voltage, current, power, power factor, frequency) for a phase or for a complete system value. The transducer is supplied with a universal supply module within the range from 24 to 300 V DC or 40 to 276 V AC voltage. Beside AC measuring transducers we produce also DC programmable measuring transducers for conversion of DC current and voltage, resistance and temperature into appropirate DC current or voltage signals. Their analogue output signal is proportional to the measured value and it is appropriate for regulation of analogue and digital devices. Input quantities for DC measuring transducers can vary from 50 mv to 300 V for voltage and from 1 ma to 1 A (up to 7.5 A as special version) for current. Output values are similar to output values of AC measuring transducers. Accuracy class for both (current and voltage) DC measuring transducer is 0.5. MISET Software / Application MISET software is created for configuring and setting of all the instruments with serial communication port (RS232 or RS485) connected in your power network. Devices must be connected to the computer via RS232 communication port (one device, or up to 32 devices connected in network via RS485/RS232 communication converter). With MISET software you can set any parameter of your device, such as input values and transformer ratios, type and value of output and its characteristic, address, communication speed. It also displays measured values in numerical format and in table form. PC software MISET is user friendly and involves help function to simplify the work. MISET Software / System requirements - Windows 95, 98, Millennium, 2000, XP, NT MB available disk space - VGA monitor - Min. 32 MB of RAM - CD drive - RS232 communication port Measuring quantities - AC voltage and current - RMS AC voltage and current - Active and reactive power - Frequency - Power factor - Resistance - DC voltage and current - Temperature - TAP position
3 Differences between measuring transducers Our measuring transducers can be divided into two groups: MI400 multifunctional measuring transducer and all the others. MI400 is the most powerful multifunctional measuring transducer. It supervises simultaneously any 3 values of an electrical system. It has the capability of measuring more than 50 different electrical quantities such as: TRMS values of voltage, current, kw, kvar, kva, PF, Hz, MD, THD etc in one instrument. All values are available via communication port for monitoring on the PC. It can have up to three configurable analogue outputs, which are programmable. Programmable are also CT and VT ratios. All the other measuring transducers compose group MI4xx (4xx greater than 400). Each measuring transducer in this group is tailored for measuring one electrical quantity. In the table below you can see which functionality is covered by which instrument and instrument's input and output values. Input quantity Programmable Active power Reactive power Power factor transducer transducer transducer measuring TYPE MI400 MI413 MI414 MI421 Class With auxiliary power supply Measuring principle Microprocessor control Measuring range -Pn Pn -Pn Pn -Qn Qn Cap Ind. -Qn Qn 0...Pn 0...Qn Sn Sn Cap Ind Hz Un In Input voltage Un V Nominal voltage Programmable range Input current In A Nominal current Programmable range Nominal frequency 50/60 Hz Consumption/Input Voltage circuit: U 2 /3 MΩ Current circuit: Ι 2 x 0.01 Ω resistance Overload capability Range selection Numbers of analogue outputs Current nominal values 1.5 Un; 2 In 57, 100, 110, 230, 400, 500 V AC, ± 20%, Hz 3 VA Universal auxiliary power supply V DC V AC Programmable range over communication, at placing order 0, 1, 2 and ma...0 (0.2)...1 ma -5 ma...0 (1)...5 ma -10 ma...0 (2)...10 ma -20 ma...0 (4)...20 ma -1 V V, -10 V V Yes (Optional)- Voltage nom. values Harmonic analysis Maximum Demand Yes - Communication RS232 or RS485 RS232, RS485 (optional) Residual ripple < 1 % p.p. on nominal current Response time < 300 ms Burden max. I output 5 ma 3 kω, 10 ma 1.5 kω, min. U output 20 ma 750 Ω, 10 V 500 Ω Working temperature C Storage temperature C Climatic class 3 according to EN General technical data Protection system: IP 50, terminals IP20, according to EN 60529, 1989 Characteristic curves Dimensions A, B, C, D A = 100 mm, B = 75 mm, C = mm
4 Input quantity 3 x AC - 3 x AC - Frequency Voltage Current TYPE MI436 MI438 MI420 Class With auxiliary power supply Measuring principle Microprocessor control Measuring range V to V 0..6 A, 1 A, 5 A 40 to 70 Hz Input voltage 500 V programmable, V Nominal voltage 57.74, 63.5, 100, 110, 230, 250, 400, 500 V fixed configuration Input current Nominal current Nominal frequency 50/60 Hz 6 A programmable 1 A, 5 A fixed configuration Hz Hz Hz Hz Consumption / Input U 2 / 3 MΩ I Ω < 0.5 VA resistance Overload capability 1.2 Un 2 In 1.2 Un Universal auxiliary power supply 57, 100, 110, 230, 400, V DC, V AC, Hz, < 3 VA 500 V AC, ±20%, Universal auxiliary power supply V DC V AC Range selection Programmable range over communication, at placing order Number of analogue outputs 3 1 Current nominal values 0 (0.2)...1 ma 5 ma, 20 ma 0 (1)...5 ma programmable 10 ma fixed configuration 5 ma, 10 ma, 20 ma, 0 (4)...20 ma ma fixed ma fixed configuration Voltage nom. values V to V 10 V programmable, fixed Harmonic analysis Yes (Optional)- Maximum Demand - Yes (thermal function)- Communication RS232, RS485 (optional) Residual ripple on < 1% p.p. nominal current Response time < 300 ms Burden max. I output 5 ma 3 kω, 10 ma 1.5 kω, 20 ma 750 Ω, 10 V 500 Ω min. U output Working temperature C C Storage temperature -40 to +70 C C Climatic class 3 according to EN according to EN General technical data Protection system: IP 50, terminals IP20, according to EN 60529, 1989 Characteristic curves A, B A, B, D Dimensions A = 100 mm, B = 75 mm, A = 44.8 mm, B = 75 mm, C = mm C = mm
5 Input quantity AC - Voltage AC - Current RMS RMS AC - Voltage AC - Current TYPE MI406 MI408 MI416 MI418 Class 0.5 Without auxiliary power supply With auxiliary power supply Measuring principle Rectifier method Microprocessor control Measuring range Un 0...In Un In Input voltage Un to V Un V to V programmable range Nominal voltage 57.74, 63.5, 100, 57.74, 63.5, 100, 110, 250, 500 V 110, 230, 250, 400, 500 V Input current In A to A In 0..6 A programmable range Nominal current 1 A, 5 A In 1 A, 5 A fixed configuration Nominal frequency 50/60 Hz Consumption / Input < 2 VA < 2 VA < 0.5 VA < 0.5 VA resistance Overload capability 1.2 Un 2 In 1.2 Un 2 In 57, 100, 110, 230, 400, 500 V AC, ± 20 %, from measuring circuit Hz 3 VA Universal auxiliary power supply V DC, V AC Range selection At placing order Programmable range over communication, at placing order Number of analogue outputs 1 Current nominal values ma 0 (0.2)...1 ma ma 0 (1)...5 ma ma 0 (2)...10 ma 0 (4)...20 ma Voltage nom. values V, V Harmonic analysis - Yes (Optional) Maximum Demand - Communication - RS232, RS485 (optional) Residual ripple on nominal current < 1% p.p. Response time < 300 ms Burden max. I output 5 ma 3 kω, 10 ma 1.5 kω, 5 ma 3 kω, 10 ma 1.5 kω, min. U output 20 ma 750 Ω 20 ma 750 Ω, 10 V 500 Ω Working temperature C Storage temperature C Climatic class 3 according to EN General technical data Protection system: IP 50, terminals IP20, according to EN 60529, 1989 Characteristic curves A A, B, D Dimensions A = 44.8 mm, B = 75 mm, C = mm
6 Input quantity Temperature Resistance Potenciometer & Pt 100 TAP position TYPE MI450 MI452 MI454 Class 0.5 With auxiliary power supply Measuring principle Microprocessor control Measuring range Ω to kω 0...Rn Ω to kΩ Un < 2.2 V R0 Rn...R0 Un < 2.2 V Input value -200 C +850 C for Pt Rn Ω - 50 kω Rn 100 Ω to 500 kω -60 C +250 C for Ni Ω kω programmable 20 Ω to 10 kω for programmable polinom programmable Nominal value 0 to 100, 0 to 250, Rn 100, 1 k, 2 k, 5 k, Rn 100, 1 k, 2 k, 5 k, 10 k -100 to 800 C for Pt 10 k, 20 k, 50 kω fixed 20 k, 50 k, 100 k, 200 k, 0 to 100, 0 to 180, Rn 5 k, 10 k, 50 k, 100 k, 500 kω 0-linear -50 to 150 C for Ni 200 k, 500 kω fixed Rn 300, 1 k, 2 k, 5 k, 10 k, fixed configuration 20 k, 50 k, 100 k, 200 k, 500 kω 10 steps (both fixed configuartion) Nominal frequency - Consumption / Input resistance < 0.5 VA 57, 100, 110, 230, 400, 500 V AC, ± 20 %, Universal auxiliary power supply: V DC, V AC Range selection Programmable range over communication, at placing order Number of analogue 1 outputs Current nominal (0.2)...1 ma 0 (0.2)...1 ma values (1)...5 ma 0 (1)...5 ma (4)...20 ma 0 (4)...20 ma Voltage nom. values V, V V, V Harmonic analysis - Maximum Demand - Communication RS232, RS485 (optional) Residual ripple on < 1 % p.p. nominal current Response time Programmable 0.5 s to 60 s Burden max. I output min. U output 5 ma 3 kω, 10 ma 1.5 kω, 20 ma 750 Ω, 10 V 500 Ω Working temperature C Storage temperature C Climatic class 2 according to EN General technical Protection system: IP 50, terminals IP20, according to EN 60529, 1989 data Characteristic curves A, B, C, D A Dimensions A = 44.8 mm, B = 75 mm, C = mm
7 Input quantity DC - DC - RS232 to Voltage Current RS485 TYPE MI456 MI458 MI485 Class With auxiliary power supply Measuring principle Microprocessor control - Measuring range 0...Un 0...In RS485 -Un 0...Un -In 0...In Bit rate to bit/s Input value Un mv 1 V In ma V ma V programmable programmable Nominal input Un 50, 100, 500 mv, In 1, 1.5, 2, 2.5, 4, 5, 6, 1 V fixed 10 ma fixed 1.5, 2, 2.5, 4, 5, 6, In 15, 20, 25, 40, 50, 10, 15, 20, 25, 40, 60, 100 ma fixed 50 V fixed 60, 100, 150, 200, 250, 400 V fixed Nominal frequency DC - Consumption / < 0.5 VA < 0.5 VA Input resistance Overload capability 1.2 Un 2 In - 57, 100, 110, 230, 400, 500 V AC, ± 20 %, Hz 3 VA Universal auxiliary power supply V DC V AC Range selection Programmable range over communication RS232 at placing order Electrically isolated Number of analogue 1 Terminals or SUB D outputs connector Current nominal -1 ma...0 (0.2)...1 ma Indication values -5 ma...0 (1)...5 ma communication with -20 ma...0 (4)...20 ma LED Diode Voltage nom. values -1V V, -10V V Harmonic analysis - Maximum Demand - Communication RS232, RS485 (optional)- Residual ripple on < 1% p.p. - nominal current Response time Programmable 0.5s to 3s - Burden max. I output min. U output 5 ma 3 kω, 10 ma 1.5 kω, 20 ma 750 Ω, 10 V 500 Ω - Working temperature C Storage temperature C Climatic class 3 according to EN General technical data Protection system: IP50, terminals IP20, according to EN 60529, 1989 Characteristic curves A, B, C, D - Dimensions A = 44.8 mm, B = 75 mm, C = mm Note: Transducers according to EN , EN
8 Characteristic curves a) linear characteristic b) up to 5 break points c) zoom absolute value d) zoom Case dimensions Ordering info Ordering informations for each transducer are available in technical leaflets. Version 2, September 2004
MT 560/UMT TRANSDUCER & ANALYZER
MT 560/UMT 560 - TRANSDUCER & ANALYZER USE The MT 560/UMT 560 multi transducer and analyzer is used for a permanent analysis of electricity supply quality in compliance with the SIST EN 50160 standard.
More informationMeasuring Transducer MT4xx series Programmable AC Current Transducer MT418
Measuring Transducer MT4xx series Programmable AC Current Transducer MT418 o RMS AC current or frequency measurements o Current auto range measurements up to 12 A o Frequency measurement range 16 400 Hz
More informationProgrammable AC Current Transducer MT418
Programmable AC Current Transducer MT418 RMS AC current measurements Current auto range measurements up to 12 A Frequency measurement range 16 400 Hz AC or universal wide auiliary power supply range 24
More informationProgrammable AC Voltage Transducer MT416
Programmable AC Voltage Transducer MT416 RMS AC voltage or frequency measurements Voltage auto measurements up to 600 V L-N Frequency measurement 16 400 Hz AC or universal wide auiliary power 24 300 Vdc,
More informationELECTRICAL NETWORK RECORDER - MC 750 ELECTRICAL NETWORK ANALYZER -MC 760 ENERGY METER - MC 720 POWER METER - MC 710 MULTIFUNCTION METER - MC 740
ELECTRICAL NETWORK ANALYZER -MC 760 ELECTRICAL NETWORK RECORDER - MC 750 MULTIFUNCTION METER - MC 740 ENERGY METER - MC 720 POWER METER - MC 710 WE RECORD QUANTITIES OF ELECTRICAL NETWORK, MEASURE INSTANTANEOUS
More informationMeasuring transducers
Measuring transducers MT4xx and (U)MT5xx Measuring transducer MT440 MT 440 Programmable multifunctional transducer Real time measurements of more than 50 quantities Power accuracy class 0.5 16 adjustable
More informationMeasuring centers MC7x0 series Multifunction Meter MC740
Measuring centers MC7x0 series Multifunction Meter MC740 o Measurements of instantaneous values of more than 130 quantities (U, I, P, Q, S, PF, PA, f, φ, THD, MD, energy, energy cost by tariffs, etc.)
More informationEnergy Meters for DIN Rail Mounting Electric energy meter WS0101, WS0102,WS1102 WS0301, WS0302,WS1302
Energy Meters for DIN Rail Mounting Electric energy meter WS0101, WS0102,WS1102 WS0301, WS0302,WS1302 Direct connection up to 65 A (WSx10x) Connection with current transformer (WSx30x) Industrial or meters
More informationn True RMS measurement n Fully onsite programmable input voltage range (for CIP-V)
Tranducers for alternating current/voltage n True RMS measurement n Fully onsite programmable input voltage range (for CIP-V) and input current range (for CIP-I) n Available in single or dual output type
More informationProduct Guide. Transducers
x y Product Guide Transducers 800.U.001.01 P/Q f for AC Current or AC Voltage: A1U / V1U 2.2 also self-powered: AU / VU 2.0 for Active or Reactive Power in single phase systems: EW / EB 2.2 in balanced
More informationEnergy Management Modular Smart Power Transducer Type SPT-90
Energy Management Modular Smart Power Transducer Type SPT-90 Class 0.5 (current/voltage) 16-bit µp-based modular smart power transducer Measurements of: W, Wavg, VA, VAr, PF, Wh, VAh, VArh, Amax (among
More informationUniversal measuring transducer
Universal measuring transducer EM4000 Compact housing High accuracy Full galvanic separation MODbus (RS232/RS485) 3 Analogue + 1 Pulse output Direct voltagemeasurement up to 690V 48 hour service EXW ELEQ
More informationMICROPROCESSOR-BASED METERING EQUIPMENT SECTION 16901C PART 2
PART 1 PART 2 PRODUCTS 2.01 MANUFACTURERS A. Eaton products B.. C.. The listing of specific manufacturers above does not imply acceptance of their products that do not meet the specified ratings, features
More informationDATA SHEET Selectable AC transducer TAS-311DG
DATA SHEET Selectable AC transducer Measuring on AC networks Class 0.5 (IEC688) measurement Supply/measur. voltage up to 690 V Easy configuration via PC interface possible DEIF A/S Frisenborgvej 33 DK-7800
More informationData Sheet 066.8e. Transducers for Active and Reactive Power EW+B 2.2 DGW+B 2.2 VGW+B 2.2 DUW+B 2.2 VUW+B 2.2
Data Sheet 066.8e Transducers for Active and Reactive Power EW 2.2 DGW 2.2 VGW 2.2 DUW 2.2 VUW 2.2 Application The E/DG/VG/DU/VU W 2.2 power transducers convert all forms of active and reactive power polarity
More informationTheta 20A / 20V. Technical Data Sheet. Special Features
Technical Data Sheet Theta 20A / 20V Theta 20A / 20V is used to measure and convert AC Voltage or Current input into a load independent DC current or voltage output signal. Special Features Available in
More informationRI-D440. Three Phase easywire Multifunction DIN Rail Energy Meter. Telephone : +44 (0) Displayed Parameters
RI-D440 Three Phase easywire Multifunction DIN Rail Energy Meter Four module DIN rail mounted Energy pulse LED 330mV Input from easywire CTs (or -/1A and -/5A current transformer input with TAS-SCTEWA
More informationRI-F200 Series. Single and Three Phase Multifunction Energy Meter. Telephone : +44 (0) Displayed Parameters
RI-F200 Series Single and Three Phase Multifunction Energy Meter DIN 96 panel mounted -/1A or -/5A current transformer input Single phase or three phase network compatible Programmable voltage and current
More informationUNIVERSAL MEASURING INSTRUMENTS. TNM 34xx. TNM 3410 / 3420 / 3430 / 3440 Universal measuring instrument 1/49
TNM 3410 / 3420 / 3430 / 3440 Universal measuring instrument True RMS measurement User-friendly programing Four different types for optimal specification RS485 interface For 3- or 4-wire connection Compact
More informationMBS AG. KBR 18 Split-core current transformer. Further information about our new split-core current transformer KBR 18: Dimensions:
KBR 18 Split-core current transformer Dimensions: Round conductor: 18 mm Transformer width: 41.6 mm Transformer height: 64.5 mm Transformer depth incl. fixing clasps: 67.3 mm General technical specifications:
More informationIntegra 1560 and 1580 Digital Transducer Systems
Integra 1560 and 1580 multi function transducers provide high accuracy
More informationULTRA RAPID POWER QUALITY ANALYZER
ULTRA RAPID POWER QUALITY ANALYZER Ultra rapid (cycle by cycle) advanced electrical network analysis Complete network harmonics analysis, up to 63 rd harmonic High visibility, 5 graphic LCD screen with
More informationND40 - POWER NETWORK ANALYZER /RECORDER
ND40 - POWER NETWORK ANALYZER /RECORDER EXAMPLE OF APPLICATION 0/4..20 ma Ethernet www/ftp/smtp T Ethernet TCP IP T2 RS-485 Pt00 USB HOST/ SDCARD Pt00 MEASUREMENT AND VISUALIZATION OF POWER NETWORK PARAMETERS
More informationEnergy Management Modular Power Analyzers Type WM2-96
ISE, Inc. - 10100 Royalton Rd. - Cleveland, OH 44133 USA Energy Management Modular Power Analyzers Type WM2-96 - Tel: (440) 237-3200 - Fax: (440) 237-1744 - http://instserv.com Class 1 Modular power analyzer
More informationNETWORK ANALYZERS Analyzers
CONTENTS PRODUCTS RANGE NA.03 NETWORK ANALYZER - LCC NETWORK ANALYZER - LCA NETWORK ANALYZER - LDA NETWORK ANALYZER - LAB96 NETWORK ANALYZER - LABM NA.04 NA.06 NA.09 NA.10 NA.13 NETWORK ANALYZER - LCCM
More informationPEM353. Universal measuring device
353 Universal measuring device 353_D00335_00_D_XXEN/06.2018 353 Universal measuring device Product description The digital universal measuring device 353 is used to record and display measured quantities
More informationPRELIMINARY DATA SHEET RI-D140. Three Phase Multifunction DIN Rail Energy Meter (MID Certified) MID
RI-D140 Three Phase Multifunction DIN Rail Energy Meter (MID Certified) Four module DIN rail mounted Energy pulse LED True RMS measurement Cost effective and accurate Modbus communication -/1A or -/5A
More informationRISH Ducer E13 3 channel transducer for AC current and voltage
RISH Ducer E13 3 channel transducer for C current and voltage The RISH Ducer E13 ( Fig. 1) converts 3 sine wave C current or C voltage into 3 output signals that can serve several receiving instruments
More informationDE MEDIDA PROGRAMABLES - CLASE 0,2 MEASURING PARAMETER. Apparent power, per phase and total
PROGRAMMABLE TRANSDUCER CP00_ - CP300_ - CP00_ VERTIDORES PROGRAMABLES - CLASE 0, ONVERTIDORES PROGRAMABLES CLASE 0, - Measuring transducer controlled by a- 16-bit microprocessor. - Settable through software.
More informationPOWER TRANSDUCERS FOR SINGLE-PHASE AND THREE-PHASE NETWORK ISO P11P, P13P and P13B mm SERVICE MANUAL
POWER TRANSDUCERS FOR SINGLE-PHASE AND THREE-PHASE NETWORK PP, PP and PB ISO 900 C E R T Y F I K A T 4 mm SERVICE MANUAL Contents Page. APPLICATION... 2. BASIC REQUIREMENTS.... TRANSDUCER SET... 4 4. TECHNICAL
More informationRISH Master Digital Multifunction Instrument with onsite pluggable output options. Application : Product Features:
Application : RISH Master 3430 measures important electrical parameters in 3 phase and single phase Network & replaces the multiple analog panel meters. It measures electrical parameters like AC current,
More informationBU: EPBP GPG: DIN Rail Products Devices for the permanent control of insulation on supply lines for medical locations ISOLTESTER-DIG-RZ/RS/PLUS
INSTRUCTION MANUAL BU: EPBP GPG: DIN Rail Products Devices for the permanent control of insulation on supply lines for medical locations ISOLTESTER-DIG-RZ/RS/PLUS 1/23 More information than that reported
More informationTheta Hz. Technical Data Sheet. Special Features
Technical Data Sheet Theta Hz Theta Hz the transducer is used for frequency measurement. The output signal is proportional to measured frequency and is either load independent DC Current or load independent
More informationOperating Guide October 2006
Operating Guide October 2006 Safety 1 Safety This manual represents your meter as manufactured at the time of publication. It assumes standard software. Special versions of software may be fitted, in which
More informationMEASURING TRANSDUCERS PROGRAMMABLE TRANSDUCERS
PROGRAMMABLE TRANSDUCERS CONTENTS GENERAL FEATURES, DIMENSIONS STANDARDS, GENERAL TECHNICAL SPECIFICATIONS ORDERING INFORMATION TECHNICAL SPECIFICATIONS - INPUTS, OUTPUTS, AUXILIARY VOLTAGE FOR ALTERNATING
More informationALPHA 20 MULTIFUNCTION METER (ALPHA SERIES)
Alpha Series www.sifamtinsley.co.uk Multifunction Meters Transducers & Isolators Temperature Controllers Converters & Recorders Digital Panel Meters Current Transformers Analogue Panel Meters Shunts ALPHA
More informationPower analyzers and Energy Meters. Multifunction indicator. Type WM12-DIN. Product Description. How to order WM12-DIN AV5 3 D X.
Power analyzers and Energy Meters Multifunction indicator Type WM12-DIN Accuracy ±0.5 F.S. (current/voltage) Multifunction indicator Display of instantaneous variables: 3x3 digit Variable system and phase
More informationData Sheet. RISH Master Record %THD
Data Sheet %THD Application : measures important electrical parameters & replaces the multiple analog panel meters. It measures electrical parameters like AC current, Voltage, frequency, active energy
More informationEnergy Management Power Analyzer with plug-in Output Modules Type W M22-DIN
Energy Management Power Analyzer with plug-in Output Modules Type W M22-DIN Front dimensions: 9 DIN modules Analogue output by means of optional module (20mA or 10VDC) RS 422/485 Serial port by means of
More informationPower Quality and Energy Measurement PEM575
Power Quality and Energy Measurement _D00016_03_D_XXEN/12.2015 Power Quality and Energy Measurement Product description The digital universal measuring device is suited for measuring and displaying electrical
More informationPower analyzers and Energy Meters Power Analyzer Type WM14-DIN
Power analyzers and Energy Meters Power Analyzer Type WM14-DIN Optional RS422/485 serial port Alarms (visual only) V LN, An Class 2 (active energy) Class 3 (reactive energy) Accuracy ±0.5 F.S. (current/voltage)
More informationPower Quality and Energy Measurement PEM575
Power Quality and Energy Measurement _D00016_00_D_XXEN/06.2013 Power Quality and Energy Measurement Product description The digital universal measuring device is suited for measuring and displaying electrical
More informationPower Quality and Energy Measurement PEM533
Power Quality and Energy Measurement _D00013_02_D_XXEN/11.2014 Power Quality and Energy Measurement 0.5 S Product description The digital universal measuring device is suited for measuring and displaying
More informationJewell DPM Power / Power Factor Size 96/96 BEST IN CLASS
Application: The Jewell DPM Power 96x96 series measures system active Power (Import/Export), Reactive Power (Import/Export), Apparent Power & Power Factor of Three Phase and Single Phase Network. It has
More informationMeasuring centers MC3x0 series Energy Meters with Power Display Energy Meter WQ0217 & WQ1217 Energy Meter with analogue pointer WQ0207 & WQ2207
Measuring centers MC3x0 series Energy Meters with Power Display Energy Meter WQ0217 & WQ1217 Energy Meter with analogue pointer WQ0207 & WQ2207 o 7 digits electromechanical register o Up to 2 registers
More informationMBS AG EMBSIN 120 UV. without auxiliary voltage supply housing for 35 mm DIN rail mounting
EMBSIN 120 UV Measuring transducers for AC current : Sinus-shaped alternating voltage (0 20 A or 0 500 V) : Unipolar output signal measuring principle: Rectifier mean value measurement process economic
More informationALPHA 50 MULTIFUNCTION METER (ALPHA SERIES)
Alpha Series www.sifamtinsley.co.uk Multifunction Meters Transducers & Isolators Temperature Controllers Converters & Recorders Digital Panel Meters Current Transformers Analogue Panel Meters Shunts ALPHA
More informationN30P DIGITAL PANEL METER
N30P DIGITAL PANEL METER Features: NEW Measurement of single-phase network parameters: voltage, current, active, reactive and apparent power, cosj, tgj, j, frequency, active, reactive and apparent energy,
More informationMeasurement and control. Digital instruments and measuring transducers
Measurement and control Digital instruments and measuring transducers M.2 - Digital instruments and measuring transducers Introduction...M2-3 Product selection table...m2-5 DC Series Digital indicator
More informationMETRAClip87 and 88 Clamp Multimeters
3-349-795-03 1/7.14 Current and frequency measurement via clamp meter: METRAClip87: 1500 A AC TRMS and 1500 A DC METRAClip88: 2000 A AC TRMS and 3000 A DC Multimeter functions via connector sockets: V
More informationEASTRON SDM630MCT-RJV / SDM630MCT-RJA User Manual V1.1. Three phase multifunction din rail energy meter
SDM630MCT-RJV-333mV SDM630MCT-RJA-00mA Three phase multifunction din rail energy meter Plug-in solution; labor saving; wiring mistake free Measures kwh KVarh, KW, Kvar, KVA, P, F, PF, Hz, dmd, V, A, THD,etc.
More informationRISH EM 3490 DS Dual Source Energy Meter (With All Display Parameters) RISH EM 3490 DS. Application : Product Features:
(With All Display Parameters) Application : RISH EM 3490 DS measures important electrical parameters of Utility (in normal mode) & Generators (in Power back up) in three phase and single phase Network
More informationRISH PQM. Power Quality Monitor. Preliminary Datasheet subject to change without notice. Individual Harmonics measurement upto 56th Harmonics
Power Quality Monitor Individual Harmonics measurement upto 56th Harmonics True representation of Voltage & Current waveforms. Phasor Representation of All 3 phases for system analysis Real Time Clock
More informationPOWER TRANSDUCERS ACTIVE AND REACTIVE SERIES: T-W WATT T-V VAR
POWER TRANSDUCERS ACTIVE AND REACTIVE SERIES: T-W WATT T-V VAR The T-W or T-V power transducer converts ac current and voltage signals into a load independent dc signal proportional to active power (watts)
More informationPower Meter Series PM3200 Functions and characteristics
Functions and characteristics PB108433 This PowerLogic Power meter offers basic to advanced measurement capabilities. With compact size and DIN rail mounting, the PM3200 allows mains and feeders monitoring
More informationEM-72 Electricity Meters for Current Transformers
Product sheet MT8.18 Meter EM72 EM-72 Electricity Meters for Current Transformers EM72 electricty meters have been designed for panel mounting to monitor electricity consumption and the quality of the
More informationRISH EM 3490 SS Kilowatt Hour Energy Meter With Rs485 RISH EM 3490 SS. Application : Product Features: Indication: Pulse Indication:
Application : RISH Master 3490 SS is a 96mm x 96mm panel mounted kilowatt hour meter it measures active energy with class 1.0 accuracy having auto-resetting 8 digit seven segment LED counter. The unit
More informationJUMO dtrans T04 Four-wire Transmitter, settable via DIP switch/pc setup program
JUMO GmbH & Co. KG Delivery address:mackenrodtstraße 14, 36039 Fulda, Germany Postal address: 36035 Fulda, Germany Phone: +49 661 6003-0 Fax: +49 661 6003-607 e-mail: mail@jumo.net Internet: www.jumo.net
More informationEnergy Management Energy Analyzer Type EM210 MID
Energy Management Energy Analyzer Type Multi-use housing: for both DIN-rail and panel mounting applications MID annex MI-003 (Measuring Instruments Directive) compliant Class B (kwh) according to EN50470-3
More informationEnergy Division
Energy Division http://energy.tycoelectronics.com Installation and Operating Manual Integra 1560 and 1580 Digital Metering and Transducer Systems Tyco Electronics UK Limited Crompton Instruments Freebournes
More informationInstallation and Operating Instructions
Energy Division Installation and Operating Instructions Quadratic Integra 1530 Digital Metering Systems Our commitment. Your advantage. Contents Page 1 Introduction 4 1.1 Measurement Capabilities 5 1.2
More informationSINEAX V 624 Programmable Temperature Transmitter for RTD and TC inputs
SINEAX V 6 for rail mounting in housing P/7 or P/7 St 00 II () GD Application SINEAX V 6 (Figs. and ) is designed for measuring temperature in combination with thermocouples or resistance thermometers.
More informationSINEAX I 503 / SINEAX U 504 Transducer for AC current or AC voltage
Application The transducers SINEAX I 503/U 504 (Figs. 1 and 2) are designed to convert a sinusoidal AC current or voltage into a load independent DC signal proportional to the measured value. This output
More informationEnergy Management Energy meters Type EM2-DIN
Energy Management Energy meters Type 6-dgt µp-based indicator Manual scrolling of partial and total energies: kwh, kvarh. TRMS measurement of distorted waves (voltage/current) All configuration functions
More informationEnergy Management Three-phase energy meter with output modules Type EM4-DIN
Energy Management Three-phase energy meter with output modules Type EM4-DIN Class 1 (active energy) Class 2 (reactive energy) Three-phase multi-function energy meter Back-lighted LCD display 3 1 / 2 DGT
More informationAPPLICATION: The heart of the system is a DSR 100 Digital Static Regulator used in conjunction with standard SCR based rectifier bridges.
APPLICATION: Basler Electric offers a New Line of digitally controlled brush (static) or brushless excitation systems designed for use with existing Hydro, Gas as well as Diesel driven generators requiring
More informationDEIF A/S. TAS-311DG Selectable AC transducer J (UK) Installation and start up instructions
Installation and start up instructions TAS-311DG Selectable AC transducer Voltage, current, frequency or phase angle transducer Supply voltage up to 690V DEIF A/S Configuration via PC-interface possible
More informationSINEAX V 604s Programmable multifunctional transmitter
SINEAX V 60s f direct currents, direct voltages, temperature senss, teletransmitters potentiometers 00 SINEAX V60s is a multifunctional transmitter f top-hat rail assembly with the following main characteristics:
More informationRISH Master 3430 DIGITAL MULTI-FUNCTION TRANSDUCER. Electro-Meters
measures important electrical parameters in phase and single phase etwork & replaces the multiple analog panel meters. It measures electrical parameters like AC current, Voltage, frequency, Power, Energy
More informationDigital Meters With A Multicolour Bargraph LEL-NA3 one-channel LEL-NA5 one-channel LEL-NA6 two-channel
Digital Meters With A Multicolour Bargraph LEL-NA3 one-channel LEL-NA5 one-channel LEL-NA6 two-channel Digital-analogue meters of LEL-NA series with a multicolour bargraph have a universal input destined
More informationINSTRUCTIONS MANUAL DEVICE FOR THE PERMANENT CONTROL OF INSULATION ON THE SUPPLY LINES IN MEDICAL PRACTICE PLACES INSTALLATIONS HRI-R40W
Page 2 / 16 INDEX: GENERAL TYPES ACESSORIES AND OPTIONS INSTALLATION WIRING DIAGRAMS CONNECTING TERMINALS DIAGRAMS WIRING DIAGRAM DESCRIPTION WORKING DESCRIPTION AND KEYBOARD WORKING DESCRIPTION AND PROGRAMMING
More informationsw rev. 55B DEVICE FOR THE PERMANENT CONTROL OF INSULATION ON THE SUPPLY LINES IN MEDICAL PRACTICE PLACES INSTALLATIONS
INSTRUCTIONS MANUAL IM831-U v0.92 HRI-R40W sw rev. 55B DEVICE FOR THE PERMANENT CONTROL OF INSULATION ON THE SUPPLY LINES IN MEDICAL PRACTICE PLACES INSTALLATIONS INDEX: GENERAL TYPES ACESSORIES AND OPTIONS
More informationPaladin Transducers 250 Series Class 0.5 and Class 0.2
Paladin Transducers 250 Series Class 0.5 and Class 0.2 An extensive range of transducers providing measurement, isolation and conversion of electrical parameters into industry standard DC output signals.
More informationEnergy Management Energy Meter with plug-in Output Modules Type EM4-DIN
Energy Management Energy Meter with plug-in Output Modules Type EM4-DIN Degree of protection (front): IP 40 Front dimensions: 9 DIN modules RS 422/485 Serial port by means of optional module Dual pulse
More informationINSTALLATION INSTRUCTIONS QUICK START GUIDE. Multi-transducer, MTR-3. Document no.: B SW version 3.0X.X or later
INSTALLATION INSTRUCTIONS QUICK START GUIDE Multi-transducer, MTR-3 Document no.: 4189300022B SW version 3.0X.X or later Table of contents 1. ABOUT THIS DOCUMENT... 3 GENERAL PURPOSE... 3 CONTENTS/OVERALL
More informationXP2-R Power and Reverse Power Relay
XP2-R Power and Reverse Power Relay Manual XP2-R (Revision C) Woodward Manual XP2-RE Woodward reserves the right to update any portion of this publication at any time. Information provided by Woodward
More informationSmart Energy & Power Quality Solutions. UMG 96RM Universal measurement instrument (EN 50160, IEEE 519, ITIC)
Smart Energy & Power Quality Solutions UMG 96RM Universal measurement instrument (EN 50160, IEEE 519, ITIC) UMG 96RM UMG 96RM Universal measurement instrument Unrivalled in its class The UMG 96RM is a
More informationDM-III Multitest & DM-III Multitest F Power Quality Recorders
DM-III Multitest & DM-III Multitest F Power Quality Recorders CAT 600V TRUE RMSz Amprobe s full-featured Three-Phase Power Quality Recorders provide the essential functions and capabilities required to
More informationENGLISH 3 Phase Multi-function Power Meter 1/5A MID MID
Professionally approved products. Datasheet Stock Number: 144-0527 3 Phase Multi-function Power Meter 1/5A MID 96mm² Panel Mounted Power Meter. MID UK Specifications The 144-0527 is a new generation modern
More informationMars-Energo. Volt/mA Calibrator CALMAR-S. User s manual Edition 3.1
Mars-Energo Volt/mA Calibrator CALMAR-S User s manual Edition 3.1 Manufacturer: OOO NPP Mars-Energo Address: V.O. 13 Line, 6-8, office 41H, Saint-Petersburg, Russia, 199034 2017 MARS-ENERGO Table of contents
More informationSINEAX U 553 Transducer for AC Voltage
With power supply RMS value measurement Carrying rail housing P/0 Application he transducer SINEAX U 55 (Fig. ) converts a sinusoidal or a distorted AC voltage into a load independent DC current or a load
More informationEnergy Management Energy Analyzer Type EM210
Energy Management Energy Analyzer Type EM210 Multi-use housing: for both DIN-rail and panel mounting applications Current inputs AV option: CT 5A Current inputs MV option: current sensor 333 mv (CTV series)
More informationPower Quality and Energy Measurement PEM330/PEM333
Power Quality and Energy Measurement PEM330/PEM333 TDB310001en / 02.2013 Power Quality and Energy Measurement PEM330/PEM333 0.5S Product description The universal measuring device PEM330/333 is used to
More informationApplication Alpha 20 Measures important electrical parameters in 3 phase 4 Wire and 3 phase 3 Wire Network & replaces the multiple analog panel meters
Technical Data Sheet Alpha 20 Alpha 20 is a compact multifunction instrument which Measures important electrical parameters in 3 phase 4 Wire and 3 phase 3 Wire Network & replaces the multiple analog panel
More informationPQM3000 Class A rack 19 power quality analyzer for CTs or current clamps
Class A rack 19 power quality analyzer for CTs or current clamps Two different models, for CTs or current clamps Rack 19 mounting Harmonics and interharmonics measurement Data recording for further EN
More informationPower analyzers and Energy Meters Power Analyzer Type WM14-96
Power analyzers and Energy Meters Power Analyzer Type WM14-96 Optional RS422/485 serial port Alarms (visual only) V LN, An Class 2 (active energy) Class 3 (reactive energy) Accuracy ±0.5 F.S. (current/voltage)
More informationEnergy Management. Type WM14-96 Basic Version. Product Description. How to order WM14-96 AV5 3 D PGX. Type Selection. Input specifications.
Energy Management Power Analyzer Type WM-96 Basic Version Optional dual pulse output Alarms (visual only) V, An Optional galvanically insulated measuring inputs Product Description 3-phase power analyzer
More informationnew! nd40 example of application MeaSUreMent and ViSUalization of power network parameters Ethernet www/ ftp / smtp Ethernet TCP IP RS-485
new! nd40 - power network analyzer / recorder Measurement and recording of over 500 electric energy quality parameters acc. to en 50160, en 61000-4-30, en 6100-4-7 standards. Measuring class a - for 3
More informationFluke Fluke-Direct.ca. Three-Phase Power Logger. Technical Data
Fluke 1735 Three-Phase Power Logger Technical Data Electrical load studies, energy consumption testing, and general power quality logging The Fluke 1735 Three-Phase Power Logger is the ideal electrician
More informationUniversal-Transducer Multi-E11-MU
Universal-Transducer Multi-E11-MU Safety Informations Observe instructions! The device described in these instructions shall only be installed by a qualified electrician according to both EN 50110-1/-2
More informationSUBJECT TO CHANGE WITHOUT NOTICE
TRNSUCERS & ISTRS Theta 30P www.sifamtinsley.co.uk TSHEET Issue 1.0 Multifunction Meters Transducers & Isolators Temperature Controllers Converters & Recorders igital Panel Meters Current Transformers
More informationELEKTROTEHNI KO PODJETJE Leskoπkova cesta 12, 1000 Ljubljana, SLOVENIA
d.o.o. ELEKTROTEHNI KO PODJETJE Leskoπkova cesta 12, 1000 Ljubljana, SLOVENIA SETTING UP REACTIVE POWER COMPENSATION DEVICES SELECTING A REACTIVE POWER COMPENSATION DEVICE To effectively compensate the
More informationAMIK 200 / 201 Technical Data Sheet
AMIK 200 / 201 Technical Data Sheet AMIK Special Features MODBUS (RS-485) Communication available only on Amik 201 On site Programmable CT/PT Ratios User selectable CT Secondary 1A/5A User selectable PT
More informationNPRG860 & NPRG870 perform synchronization and paralleling of generators with electrical network. NPRG860 features a speed adjustment function.
REGULATION AUTOMATIC SYNCHRONIZER for GENERATOR NPRG860 & NPRG870 perform synchronization and paralleling of generators with electrical network. NPRG860 features a speed adjustment function. NPRG870 adds
More informationXP2-R Power and reverse power relay. (January 2006) Manual XP2-R (Revision New)
XP2-R Power and reverse power relay (January 2006) Manual XP2-R (Revision New) Woodward Manual XP2-R GB Woodward Governor Company reserves the right to update any portion of this publication at any time.
More informationNPRG860 NPRG870 REGULATION. Automatic Synchronizer for Generator
REGULATION Automatic Synchronizer for Generator NPRG860 & NPRG870 perform synchronization and paralleling of generators with electrical network. NPRG860 features a speed adjustment function. NPRG870 adds
More informationMultimeter 500CVD21 RTU500 series
Remote Terminal Units - Data sheet Multimeter 500CVD21 RTU500 series CT/VT interface with 4 voltage and 24 current inputs for direct monitoring of 3/4 wire 0 300 V AC (line to earth), 0...500 V AC (phase
More informationS200 I/O System Units
S200 I/O System Units S200 I/O is a range of cost effective I/O units which are bus compatible with S200L I/O and can be mixed with them in any order on the same DIN rail. The S200 I/O System features
More informationTechnical Data Sheet AMIK 300 / 301
USA SINCE 1936 RELIABILITY BEYOND MEASURE Technical Data Sheet AMIK 300 / 301 LISTED File No. E471457 AMIK AMIK 300 is a compact multifunction instrument with touch screen LCD utility which measures important
More informationENA33LCD. Power line analyzer. User and service manual. Obrezija 5 SI-1411 Izlake
ENA33LCD Power line analyzer User and service manual version 2.9 (FW version 6.8 and newer) ETI, d.o.o. Obrezija 5 SI-1411 Izlake www.etigroup.eu/products-services 1. Front control panel and terminal plate
More information