DE MEDIDA PROGRAMABLES - CLASE 0,2 MEASURING PARAMETER. Apparent power, per phase and total

Transcription

1 PROGRAMMABLE TRANSDUCER CP00_ - CP300_ - CP00_ VERTIDORES PROGRAMABLES - CLASE 0, ONVERTIDORES PROGRAMABLES CLASE 0, - Measuring transducer controlled by a- 16-bit microprocessor. - Settable through software. - Two, three or four analogue outputs. - Two outputs with contacts (settable as energy pulses, alarm or programmable contacts). - RS-3, RS-8 or RS-3 and RS-8 serial port. PARAMETER Line-to-neutral voltage Sen φ per phase and total Line-to-line voltage Frequency Current (true effective value) Active energy Active power, per phase and total Active energy - Reactive power, per phase and total Inductive reactive energy Apparent power, per phase and total Capacitive reactive energy Cos φ per phase and total THD Current and Voltage ANALOGUE OUTPUTS Selectable measuring parameter for each analogue output. Programmable zero and full scale in the output range. Rated values of full scale 1, and 0 ma DC. and 1, and 10 V DC., uni or bidirectional. Insulation by optocoupler. DIGITAL OUTPUTS Two relay outputs (10 A, 30 V DC. / 0 V AC.). Programmable as: Active or reactive energy pulses. - Maximum or minimum alarm signalling for any of the parameters measured. - Output contacts (operated from the central unit). SERIAL PORT RS-3, RS-8 or RS-3 and RS-8, bidirectional: - Reading only: Electrical parameters and data. - Writing only; Program data, reset and activating of output contacts. or wire direct to the device. MODBUS / JBUS communication protocol. Insulation by optocoupler. SETTING Via serial port: - Baud rate: default 9600 bauds. Address: Primary current. - Primary voltage. Analogue outputs: Measuring parameter, zero and full scale. - Digital outputs, settable as: 1.- Energy pulses:.- Alarm: Measuring parameter, value and alarm mode (max. or min.). 3.- Output contacts operated from the computer MT-17

2 TECHNICAL SPECIFICATIONS ACCURACY 0, PRECISIÓN 0, Entradas INPUTS Alternating current (A.C.) A or 1 A(.../ or.../1 A) Measuring range 0-10 % Alternating voltage (A.C.) 100, 110, 30, 00 or 0 V ANALOGUE OUTPUTS (D.C) 1,, 10, 0 or -0 ma 1,, 10, 1- or -10 V Load impedance Ro (kω) = 1 V / Io (ma) Max. Ro (kω) = Vo / 30 ma Saturation Limit Min. 1, Io 1, Vo OTHER CHARACTERISTICS OTHER CHARACTERISTICS Relays Temperature coefficient Relays Serial port RS-3, RS-8 or both Operating temperature -10 ºC to ºC Protocol JBUS/MODBUS Linearity error 0,0 Baud rate Selectable Bauds Ripple 0,1 % Operating frequency 0 and 60 Hz Response time 00 ms (0-90 % Io) 3 ºC ±1ºC Frequency coefficient Not affected Digital outputs Reference temperature inapreciable MODELS Analogue outputs CP 000 CP 001 CP 00 CP 003 Outputs: Nº.3 CP Analogue outputs CP 3000 CP 3001 CP 300 CP 3003 Outputs: Nº.3 CP000 Analogue outputs CP 000 CP 001 CP 00 CP 003 Outputs: Nº.3 MT-18 CM-0 Transducer

3 8...6 V C.A. Auxiliary voltage UNIVERSAL A.C.- D.C Auxiliary voltage A.C. 110 or 30 V ±0% Auxiliary voltage D.C V Burden VA/W Energy measuring Only in the digital outputs (relays) Maximum open circuit voltage 30 V THD harmonic distortion Not included V C.C. Without insulation between serial port and analogue output no S incluida CP CP000 CP CP V C.A. Auxiliary voltage UNIVERSAL A.C.- D.C V C.C. Auxiliary voltage D.C V W (CP3000) Burden 6W (CP000) Energy measuring Digital outputs (relays) Serial port (option) Maximum open circuit voltage Double CPCP series Doble linealine, serie 1 V RS3-RS8 (optional) RS3-RS8 (optional) OPTIONAL 10 Setting and reading software. Management software - GEST. ORDERING INFORMATION 1.- Type of transducer. For example: a) CP001 b) CP3003 c) CP00.- Secondary rated voltage and current. 3.- Auxiliary voltage..- Analogue outputs, ma (1,, 0) or V (1,, 10)..- RS-3, RS-8 or RS-3 and RS-8 serial port DIMENSIONS CP3000 CP000 SETTING DATA 1.- Primary rated voltage and current..- Analogue output range. 3.- Transfer curves (page MT.1)..- Digital outputs type: Energy pulses (incl. energy constant), alarm mode or free contacts..- Serial port: Baud rate MT-19

4 ACCESORIES IFR1 RS8/3 Converter. IFRA RS8/3 Converter with galvanic separation. IFR RS8/1RS3 Converter. C01 RS3-DB9 power cable (m). C0 RS8-IFRA power cable (m). C03 IFRA-DB9(PC) power cable (m). SF WINDOWS-Programming software. SF3 WINDOWS-Programming software CP3000. SF WINDOWS-Programming software CP000. Nº 3 MODEL RS 3 OUTPUT TERMINALS CP 3000 L L RS 8 DIGITAL SALIDA OUTPUT RLO RL1 ANALOGUE OUTPUT S1 S S3 S S CP V ma RS IFRA Nº 3 RS-3 Nº CP300X CP00X PC 7 P.C. MT-0 CM-0 L RS-8 L 9 10 Ohms L 9 Aux. V. 10 Ohms RD RTS 3 TD 33 RS-3 Transducer

5 TRANSFER CURVES A B C D E F H G I J MT-1