SINEAX V 624 Programmable Temperature Transmitter for RTD and TC inputs

Size: px
Start display at page:

Download "SINEAX V 624 Programmable Temperature Transmitter for RTD and TC inputs"

Transcription

1 SINEAX V 6 for rail mounting in housing P/7 or P/7 St 00 II () GD Application SINEAX V 6 (Figs. and ) is designed for measuring temperature in combination with thermocouples or resistance thermometers. Thermocouple non-linearities are automatically compensated. The analogue output signal is either an impressed current or superimposed voltage which is linearly proportional to temperature and can be processed by other devices for purposes of displaying, recording and/or regulating a constant. The input variable and measuring range are programmed with the aid of a PC and the corresponding software. The sensor circuit is monitored for open and short-circuits and the output responds in a defined manner if one is detected. The transmitter fulfils all the important requirements and regulations concerning electromagnetic compatibility EMC and Safety (IEC 00 resp. EN 6 00). It was developed and is manufactured and tested in strict accordance with the quality assurance standard ISO 900. Fig.. Transmitter SINEAX V 6 in housing P/7, terminals not pluggable. Features / Benefits Input variable and measuring range programmed using PC / Simplifies project planning and engineering, short delivery times, low stocking levels Measuring ranges Measured variables Limits Min. Max. span span Temperatures with resistance thermometers for two-, three- or four-wire connection Pt 00, IEC to 80 C 0 K 80 K Ni 00, DIN to 0 C 0 K 0 K Temperatures with thermocouples Type B, E, J, K, N, R, S, T acc. to IEC acc. to type mv 80 mv Type L and U, DIN 3 70 Type W Re/W6 Re, Type W3 Re/W Re acc. to ASTM E Electric isolation between input, output.3 kv and power supply 3.7 kv / Fulfils EN 6 00 Wide DC, AC power pack tolerance / Universal Available in type of protection Intrinsic safety [EEx ia] IIC (see Table 3: Data on explosion protection ) Ex devices also directly programmable on site / No supplementary Ex interface needed Fig.. Transmitter SINEAX V 6 in housing P/7 St, terminals pluggable. Open and short-circuit sensor circuit supervision / Defined output response should the supervision pick up Programmable with or without power supply connection Housing only 7. mm wide (size P/7 housing) / Low space requirement Other programmable parameters: specific measured variable data (e.g. two, three or four-wire connection for resistance thermometers, internal or external cold junction of thermocouples etc.), transmission mode, operating sense (output signal directly or inversely proportional to the measured variable) and open-circuit sensor supervision (output signal assumes fixed preset value between and 0%) / Highly flexible solutions for measurement problems Software calibration of beginning and end of output signal range Digital measured variable data available at the programming interface / Simplifies commissioning, measured variable and signals can be viewed on PC in the field Camille Bauer V 6 Le 03.0

2 GOSSEN V6 SINEAX V 6 Programmation SINEAX V 6 A PC, the programming cable PK 60 plus ancillary cable and the programming software V 600 plus are required to program the transmitter. (Details of the programming cable and the software are to be found in the separate data sheet: PK 60 Le.) METRAWATT CAMILLE BAUER Ancillary cable Interface PK 60 The connections between «PC PK 60 SINEAX V 6» can be seen from Fig. 3. The transmitter can be programmed either with or without the power supply connected. The software V 600 plus is supplied on one CD and runs under Windows 3.x, 9, 98, NT and 000. Programming connector OFF ON OFF: Connect separate power supply to SINEAX ON: Power supply provided by PC The programming cable PK 60 adjusts the signal level between the PC and the transmitter SINEAX V 6. The programming cable PK 60 is used for programming both standard and Ex versions. Fig. 3. Example of the set-up for programming a SINEAX V 6 in standard version without the power supply. For this case the switch on the interface must be set to ON. Technical data Measuring input Temperature with resistance thermometers Measuring range limits: See table 7 Resistance types: Type Pt 00 (IEC 60 7) Type Ni 00 (DIN 3 760) Other sensor types configurables Measuring current: 0.0 ma Standard circuit: resistance thermometer for two-, three or four-wire connection Input resistance: R i > 0 MΩ Lead resistance: 30 Ω per lead Temperature with thermocouple Measuring range limits: See table 7 Thermocouple pairs: Type B:Pt30Rh-Pt6Rh (IEC 8) Type E: NiCr-CuNi (IEC 8) Type J: Fe-CuNi (IEC 8) Type K:NiCr-Ni (IEC 8) Type L: Fe-CuNi (DIN 370) Type N:NiCrSi-NiSi (IEC 8) Type R:Pt3Rh-Pt (IEC 8) Type S:Pt0Rh-Pt (IEC 8) Type T: Cu-CuNi (IEC 8) Type U:Cu-CuNi (DIN 370) Type W Re/W6 Re (ASTM Type W3 Re/W Re E ) Standard circuit: thermocouple, internal cold junction with built-in Pt 00 or thermocouple, external cold junction Input resistance: Cold junction : Ri > 0 MΩ Internal: With built-in Pt 00 or with Pt 00 connected to the terminals External: Via cold junction thermostat 0 60 C, configurable Measuring output DC current*: Burden voltage: Open-circuit voltage: External resistance: Residual ripple: DC voltage*: Short-circuit current: External resistance: Residual ripple: Programmable between 0 and 0 resp. 0 and 0 ma minimum span ma V < 0 V R ext max. [kω] = V I AN [ma] I AN = Output current end value <.0% p.p., DC 0 khz Programmable between 0 and 0 resp. 0 and 0 V minimum span V 0 ma R ext min. [kω] U AN [V] ma U AN = Output voltage end value <.0% p.p., DC 0 khz * The output variable (current or voltage) is not re-programmable. Camille Bauer

3 Table : Response time Measuring Open Short- Possible response times approx. [s] mode sensor circuit circuit TC int. comp. active TC int. comp. off TC ext. comp. active TC ext. comp. off RTD L active RTD 3L, L active active RTD L,3L,L off off Programming connector Interface: Serial interface Accuracy data (acc. to EN/IEC ) Reference value: Measuring span Basic accuracy: Error limits ± 0.% at reference conditions Reference conditions Ambient temperature 3 C Power supply V DC ± 0% and 30 V AC ± 0% Output burden Current: 300 Ω Voltage: kω Settings Pt00, 3-wire, C Additional errors (additive) Low measuring ranges Voltage measurement ± µv at measuring spans < 0 mv Resistance thermometer ± 0.3 K at measuring spans < 00 C Thermocouple Type U, T, L, J, K, E ± 0, K at measuring spans < 00 C Type N ± 0.3 K at measuring spans < 30 C Type S, R ± 0. K at measuring spans < 000 C Type B ± 0.6 K at measuring spans < 00 C High initial value (Additional error = Factor Initial value) Factor Voltage measurement ± 0. µv / mv Resistance thermometer ± K / C Thermocouple Type U, T, L, J, K, E ± K / C Type N ± K / C Type S, R ± 0.00 K / C Type B ± K / C Influence of lead resistance at resistance thermometer ± 0.0% pro Ω Internal cold junction ± 0. K at 3 C, ± 0. K/0 K Linearisation ± 0.3% If hardware output end value / output span >. Influencing factors Temperature Long-time drift ± 0.% Common and transverse mode influence ± 0.% 0 ma resp. 0 V ± ( 0.07%) output span Example: Hardware output end value 0 ma New configuration 6 ma Additional error = 0 ma ± ( 0.07%) = 0.7% ma ± (0.% + 0. K) per 0 K with temperature measurement ± (0.% + µv) per 0 K with voltage measurement Open and short-circuit sensor circuit supervision Signalling modes: Output signal programmable to the value the output had immediately prior to the open or shortcircuit (Hold value) a value between and 0% of the output span Power supply DC, AC power pack (DC or...00 Hz) Table : Rated voltages and permissible variations Nominal voltages Tolerance Instruments U N Version V DC / AC V DC / AC DC % AC ± % Standard (Non-Ex) V DC % DC / AC AC ± % V AC ± 0% V DC...+ 0% Power consumption: Installation data Housing: Material of housing: Mounting:.0 W resp.. VA Type of protection Intrinsic safety [EEx ia] IIC Housing P/7 and P/7 St Dimensions see section Dimensional drawings Lexan 90 (polycarbonate) Flammability class V-0 acc. to UL 9, self-extinguishing, non-dripping, free of halogen For snapping onto top-hat rail (3 mm or 3 7. mm) acc. to EN 0 0 An external supply fuse must be provided for DC supply voltages > V. Camille Bauer 3

4 SINEAX V 6 Mounting position: Terminals: Weight: Electrical insulation: Standards Electromagnetic compatibility: Any PHOENIX screw terminals with wire guards for 0. mm to. mm Approx. 0. kg All circuits (measuring input/measuring output/power supply) are electrically insulated The standards EN and EN are observed Intrinsically safe: Acc. to EN 0 00 Protection (acc. to IEC 9 resp. EN 60 9): Housing IP 0 Terminals IP 0 Electrical standards: Acc. to IEC 00 resp. EN 6 00 Operating voltages: < 300 V between all insulated circuits Pollution degree: Installation category acc. to IEC 66: Double insulation: Test voltage: III for power supply II for measuring input and measuring output Power supply versus all circuits Measuring input versus measuring output Power supply versus: all 3.7 kv, 0 Hz, min. Measuring input versus: measuring output.3 kv, 0 Hz, min. Ambient conditions Climatic rating: IEC //3 Ambient temperature range: to + C Storage temperature range: 0 to + 70 C Annual mean relative humidity: 7%, no moisture condensation Table 3: Data on explosion protection II () GD Order Type of protection Intrinsic safety Certificate Mounting location Code Marking of instruments Instrument Measuring input 6-33/3/93/9 [EEx ia] IIC EEx ia IIC EC-type-examination Certificate ZELM 00 ATEX 007 Within the hazardous area Standard versions The following versions are available as standard versions already programmed for the basic configuration. It is only necessary to quote the Order No.: Table : Instruments in standard (non-ex) version (measuring circuit not intrinsically safe) Measuring input programmable Measuring output* Power supply Connecting Order Order screw terminals Code Nr. RTD: Pt 00, Ni 00 TC: Types B, E, J, K, L, N, R, S, T and U W/W6 Re W3/W Re 0 ma programmable between 0 and 0 resp. 0 and 0 ma minimum span ma 0 0 V programmable between 0 and 0 resp. 0 and 0 V minimum span V * The output variable (current or voltage) is not re-programmable! 60 V DC/AC not pluggable 8 30 V DC/AC V DC/AC pluggable 8 30 V DC/AC V DC/AC not pluggable 8 30 V DC/AC V DC/AC pluggable 8 30 V DC/AC Camille Bauer

5 Table : Instruments in [EEx ia] IIC version (measuring circuit intrinsically safe) Measuring input programmable Measuring output* Power supply Connecting Order Order screw terminals Code No. RTD: Pt 00, Ni 00 TC: Types B, E, J, K, L, N, R, S, T and U W/W6 Re W3/W Re 0 ma programmable between 0 and 0 resp. 0 and 0 ma minimum span ma 0 0 V programmable between 0 and 0 resp. 0 and 0 V minimum span V * The output variable (current or voltage) is not re-programmable! 60 V DC/AC not pluggable 8 0 V DC/ 8 30 V AC 60 V DC/AC V DC/ pluggable 8 30 V AC 60 V DC/AC V DC/ not pluggable 8 30 V AC 60 V DC/AC V DC/ pluggable 8 30 V AC Basic configuration: Measuring input: Resistance thermometer Pt 00 Connection mode: Three-wire connection Measuring range: C Measuring output: 0 ma resp. 0 0 V (acc. to order) Open-circuit supervision: Output.6 ma resp. V (acc. to order) Mains ripple suppression: For frequency 0 Hz Table 6: Specification and ordering information (see also Tables and : Standard versions) Order Code 6 - Features, Selection *SCODE no-go. Housing 3) Housing P/7 for rail mounting, connecting screw terminals not pluggable ) Housing P/7 St for rail mounting, connecting screw terminals pluggable Version / Power supply ) Standard / 60 V DC/AC ) Standard / 8 30 V DC/AC ) [EEx ia] IIC / 60 V DC/AC ) [EEx ia] IIC / 8 0 V DC / 30 V AC Output variable ) Current End value max. 0 ma ) Voltage End value max. 0 V Configuration 0) Basic configuration programmed, (Pt 00, three-wire, C) G ) Configurated to order Line 0: All types with basic configuration are available as standard versions, see table and, specification complete! Line : The following features to must be fully specified! Table 6: Specification and ordering information continued on next page! Camille Bauer

6 SINEAX V 6 Order Code 6 - Features, Selection *SCODE no-go. Measuring unit ) Temperatures in C ) Temperatures in F G ) Temperatures in K G Measuring mode, input connection Thermocouple ) Internal cold junction, with built-in Pt 00 T G ) External cold junction t K T G Resistance thermometer 3) Two-wire connection, R L [Ω] R G ) Three-wire connection, R L 30 Ω/wire R ) Four-wire connection, R L 30 Ω/wire R G Line : Specify external cold junction temperature t K (in C, F or K, acc. to specification in Feature ), any value between 0 and 60 C or equivalent Line 3: Specify total lead resistance R L [Ω], any value between 0 and 60 Ω 7. Sensor type / measuring range Sensor type / beginning end value of measuring range ) RTD Pt 00 Range T ) RTD Ni 00 Range GT ) RTD Pt [Ω] Range GT ) RTD Ni [Ω] Range GT B) TC Type B Range GR.. B..... E) TC Type E Range GR.. E..... J) TC Type J Range GR.. J..... K) TC Type K Range GR.. K..... L) TC Type L Range GR.. L..... N) TC Type N Range GR.. N..... R) TC Type R Range GR.. R..... S) TC Type S Range GR.. S..... T) TC Type T Range GR.. T..... U) TC Type U Range GR.. U..... W) TC W-W6Re Range GR.. W..... X) TC W3-WRe Range GR.. X..... Specify measuring range in [ C], [ F] or [K]; refer to table 7 for the operating limits for each type of sensors. Lines 3 and : Specify resistance in Ω at 0 C, any value between 0 and 000 Ω 8. Output characteristic 0) 0 00% end value ) 0 00% end value ) Inversely 00 0% end value G ) Inversely 00 0% end value G Table 6: Specification and ordering information continued on next page! Camille Bauer 6

7 Order Code 6 - Features, Selection *SCODE no-go 9. Open and short-circuit sensor signalling Output response for an open or short-circuit* sensor 0) Output at start value + 0% of the span ) Output [%] G ) Hold output at last value G A) No signal G A Line : Any value from to < 0; specify value in % of output signal span, e.g. correspondence with output 0 or 0 ma: % = 3. ma and 0% =.6 ma * The short-circuit signal is only active for the RTD measuring mode 00 Ω at 0 C and three or four-wire connection 0. Output time response 0) Standard setting time approx. s ) Setting time [s] G Line 9: Admissible values see Table. Mains ripple suppression 0) Frequency 0 Hz ) Frequency 60 Hz G Test certificate 0) Without test certificate D) Test certificate in German G... D.... E) Test certificate in English G... E.... Lines with letter(s) under no-go cannot be combined with preceding lines having the same letter under SCODE. Table 7: Measuring range limits Resistance thermometers Thermocouples Pt00 Ni00 B E J K L N R S T U C ) D ) to to to to to to to to to to to to to to R min. Ω at final value 3) 00 Ω R min. 0 Ω at final value > 00 Ω max. final value 000 Ω Initial value 0 R U min mv, max. 80 mv Initial value 0 U ) W Re W6 Re (ASTM E ) ) W3 Re W Re (ASTM E ) 3) For two-wire connection, the final value is made up of the measured final value [Ω] plus the total resistance of the leads. Camille Bauer 7

8 SINEAX V 6 Electrical connections ϑ ϑ ϑ Rw ϑ Rw 3 6 ON ON Green LED for indicating device standing by TC Internal cold junction with built-in Pt 00 TC Internal cold junction with Pt00 connected to the terminals TC External cold junction RTD Four-wire connection RTD Three-wire connection RTD Two-wire connection = Measuring input = Mesuring output = Power supply Table 8: Accessories and spare parts Dimensional drawings Description Order No. Programming cable PK 60 DSUB 9p F Interface metre Ancillary cable SINEAX Type V 6,0 metre PC software V 600 plus on CD (Download free of charge under Operating Instructions V 6 Bd 99 in German Operating Instructions V 6 Bf 09 in French Operating Instructions V 6 Be 9 in English Fig.. SINEAX V 6 in housing P/7 clipped onto a top-hat rail (3 x mm or 3 x 7. mm, acc. to EN 0 0), connecting screw terminals not pluggable Standard accessories Operating Instructions in German, French and English Type examination certificate (only for intrinsically safe explosion-proof devices) 7. Fig.. SINEAX V 6 in housing P/7 St clipped onto a top-hat rail (3 x mm or 3 x 7. mm, acc. to EN 0 0), connecting screw terminals pluggable. Printed in Switzerland Subject to change without notice Edition 03.0 Data sheet No. V 6 Le Camille Bauer Ltd Aargauerstrasse 7 CH-60 Wohlen/Switzerland Phone Fax cbag@gmc-instruments.com Camille Bauer 8

Plug-in module SIRAX V 606, 1 or 2 channels Programmable Temp. Transmitter for RTD and TC inputs

Plug-in module SIRAX V 606, 1 or 2 channels Programmable Temp. Transmitter for RTD and TC inputs Plug-in module, or channels Application The programmable transmitter (Fig. ) is designed for measuring temperature in combination with thermocouples or resistance thermometers. Thermocouple non-linearities

More information

SINEAX TV809, 1 channel Programmable Isolating Amplifier

SINEAX TV809, 1 channel Programmable Isolating Amplifier For electrically insulating, ampliflying and converting DC signals 0102 II (1) Ga II (1) Da Application The purpose of the isolating amplifi er SINEAX TV809 (Fig. 1) is to electrically insulate input and

More information

for DC currents or voltages, temperature sensors, remote sensors or potentiometers II (1) G Application Features / Benefits

for DC currents or voltages, temperature sensors, remote sensors or potentiometers II (1) G Application Features / Benefits SINEAX VC 603, Programmable for DC currents or voltages, temperature sensors, remote sensors or potentiometers 0102 II (1) G Application The SINEAX VC 603 (Figs. 1 and 2) converts the input variable a

More information

SINEAX TI 807 Passive DC signal isolator

SINEAX TI 807 Passive DC signal isolator without power supply, Ex- and non-ex version, in housing N17 or S17 for rail and wall mounting 0102 II (1) G resp. II (2) G Application The signal isolator SINEAX TI 807 serves to electrically insulate

More information

SINEAX TI 807 Passive DC signal isolator. SINEAX TI 807 Passive DC signal isolator

SINEAX TI 807 Passive DC signal isolator. SINEAX TI 807 Passive DC signal isolator SINEAX TI 807 without power supply, Ex- and non-ex version, in housing N17 or S17 for rail and wall mounting 0102 II (1) G resp. II (2) G Application The signal isolator SINEAX TI 807 serves to electrically

More information

SINEAX V 604 Programmable universal transmitter

SINEAX V 604 Programmable universal transmitter for DC currents or voltages, temperature sensors, remote sensors or potentiometers 0102 II (1) G Application The universal transmitter SINEAX V 604 (Figures 1 and 2) converts the input variable a DC current

More information

SINEAX TV 808, 1 channel Isolating Amplifier unipolar/bipolar

SINEAX TV 808, 1 channel Isolating Amplifier unipolar/bipolar For electrically insulating, amplifying and converting DC signals 0102 II (1) G Application The purpose of the isolating amplifi er SINEAX TV 808 (Fig. 1 and 2) is to electrically insulate input and output

More information

SINEAX B 811 Power Pack with additional Functions

SINEAX B 811 Power Pack with additional Functions SINEA B 8 for intelligent and conventional s, in housing S7 for rail and wall mounting 002 II () G Application The power supply unit SINEA B 8 (Figure ) provides the DC power supply for s and transfers

More information

SINEAX TV 808, 2 channels Isolating Amplifier Unipolar/Bipolar

SINEAX TV 808, 2 channels Isolating Amplifier Unipolar/Bipolar SINEAX TV 808, channels For electrically insulating, amplifying and converting DC signals Application The purpose of the isolating amplifi er SINEAX TV 808 (Fig. ) is to electrically insulate input and

More information

SINEAX TV 808, 1 channel Isolating Amplifier, output Ex or non-ex

SINEAX TV 808, 1 channel Isolating Amplifier, output Ex or non-ex for electrically insulating, amplifying and converting DC signals, also designed for FSK 1 0102 II (1) G Application The purpose of the isolating amplifi er SINEAX TV 808 (Fig. 1) is to electrically insulate

More information

Theta 60R. Technical Data Sheet. Special Features. Fig. 2 Theta R, 2 channel version, in housing S17 hole mounting brackets pulled out.

Theta 60R. Technical Data Sheet. Special Features. Fig. 2 Theta R, 2 channel version, in housing S17 hole mounting brackets pulled out. Technical Data Sheet Theta 60R 60 R 60 R Fig. Theta R, channel version, in housing S7 clipped on to a top - hat rail. Fig. Theta R, channel version, in housing S7 hole mounting brackets pulled out. Theta

More information

SINEAX I 503 / SINEAX U 504 Transducer for AC current or AC voltage

SINEAX I 503 / SINEAX U 504 Transducer for AC current or AC voltage Application The transducers SINEAX I 503/U 504 (Figs. 1 and 2) are designed to convert a sinusoidal AC current or voltage into a load independent DC signal proportional to the measured value. This output

More information

SINEAX U 553 Transducer for AC Voltage

SINEAX U 553 Transducer for AC Voltage With power supply RMS value measurement Carrying rail housing P/0 Application he transducer SINEAX U 55 (Fig. ) converts a sinusoidal or a distorted AC voltage into a load independent DC current or a load

More information

for DC currents or voltages, temperature sensors, remote sensors or potentiometers Application Principle of operation (Fig. 3) Features / Benefits

for DC currents or voltages, temperature sensors, remote sensors or potentiometers Application Principle of operation (Fig. 3) Features / Benefits for s or voltages, temperature sensors, remote sensors or potentiometers pplication The universal transmitter RISH Ducer V 604 (Figures 1 and 2) convert the input variable a or voltage, or a signal from

More information

Temperature transmitter itemp PCP DIN rail TMT 121

Temperature transmitter itemp PCP DIN rail TMT 121 Technical information TI 087R/09/en 510 03671 Temperature transmitter itemp PCP DIN rail TMT 121 Universal temperature transmitter for resistance thermometers (RTD), thermocouples, resistance and voltage

More information

SINEAX VC 603, Programmable combined transmitter/alarm unit

SINEAX VC 603, Programmable combined transmitter/alarm unit for DC currents or voltages, temperature sensors, remote sensors or potentiometers 0102 II (1) G Application The SINEAX VC 603 (Fig. 1) converts the input variable a DC current or voltage, or a signal

More information

RISH Ducer TV 808, 2 channels Isolating amplifier unipolar / bipolar

RISH Ducer TV 808, 2 channels Isolating amplifier unipolar / bipolar Fig. 1. Isolating amplifier RISH Ducer TV 808 in housing S 17 clipped onto a top - hat rail or screw hole mounting brackets pulled out. Features and Benefits Electric Isolation between input, and power

More information

SINEAX V 604s Programmable multifunctional transmitter

SINEAX V 604s Programmable multifunctional transmitter SINEAX V 60s f direct currents, direct voltages, temperature senss, teletransmitters potentiometers 00 SINEAX V60s is a multifunctional transmitter f top-hat rail assembly with the following main characteristics:

More information

KINAX 2W2 Programmable Transmitter for Angular Position

KINAX 2W2 Programmable Transmitter for Angular Position Application The KINAX 2W2 (Figs. 2 and 3) converts the angular position of a shaft into a load independent direct current signal, proportional to the angular position. The unit is contact free and has

More information

Temperature head transmitter itemp PCP TMT 181

Temperature head transmitter itemp PCP TMT 181 Technical information TI 070R/09/en Mat.-Nr.: 510 01110 Temperature head transmitter itemp PCP TMT 181 Universal head transmitter for resistance thermometers (RTD), thermocouples, resistance and voltage

More information

itemp HART DIN rail TMT112

itemp HART DIN rail TMT112 Temperature transmitter itemp HART DIN rail TMT112 Universal temperature transmitter for resistance thermometers (RTD), thermocouples, resistance and voltage transmitters, incorporating HART protocol Application

More information

SINEAX / EURAX 2I1 Passive DC signal isolator

SINEAX / EURAX 2I1 Passive DC signal isolator SINEAX / EURAX I without power supply 0 II () G resp. II () G Application The DC signal isolator SINEAX/EURAX I (Figs. and ) serve to isolate load-independent DC current signals. It suppressed noise voltages

More information

KINAX WT 717 Programmable Transmitter for Angular Position

KINAX WT 717 Programmable Transmitter for Angular Position Ruggedized version Application The KINAX WT 717 (Fig. 1) converts the angular position of a shaft into a load-independent direct current signal, proportional to the angular position. The unit is contact

More information

0 2 1 â Ó. itemp HART TMT182. Technical Information

0 2 1 â Ó. itemp HART TMT182. Technical Information Technical Information itemp HART TMT182 Temperature head transmitter Head transmitter for resistance thermometers (RTD), thermocouples (TC), resistance and voltage transmitters (mv), HART -protocol, for

More information

SINEAX I 552 Transducer for AC current

SINEAX I 552 Transducer for AC current SNEAX 55 With power supply RMS value measurement, with measuring ranges Carrying rail housing P/0 Application he transducer SNEAX 55 (Fig. ) converts a sinusoidal or a distorted AC current into a load

More information

DSCL, DSCP, SCTP. Industrial Loop Isolators and Transmitters DSCL, DSCP, SCTP. Industrial Loop Isolators and Transmitters

DSCL, DSCP, SCTP. Industrial Loop Isolators and Transmitters DSCL, DSCP, SCTP. Industrial Loop Isolators and Transmitters Industrial Loop Isolators and Transmitters DSCL,, SCTP DSCL,, SCTP Industrial Loop Isolators and Transmitters Description Dataforth s DSCL,, and SCTP series of products is a complete family of loop and

More information

RISH Ducer V604 Programmable universal transmitter

RISH Ducer V604 Programmable universal transmitter RISH Ducer V64 Programmable universal transmitter Data Sheet Programmable Universal Transmitter RISH Ducer V64 RISH Ducer V64 Fig. Transmitter RISH Ducer V64 in housing S7 clipped on a p-hat rail Fig.

More information

SINEAX G 536 Phase Angle or Power Factor Transducer

SINEAX G 536 Phase Angle or Power Factor Transducer SIEAX G Carrying rail housing P/0 Application The transducer SIEAX G (Fig. ) measures the phase angle or power factor between current and voltage of a single or -phase balanced network having a sine wave

More information

0 2 1 â Ó. itemp HART TMT182. Technical Information

0 2 1 â Ó. itemp HART TMT182. Technical Information Technical Information itemp HART TMT182 Temperature head transmitter Head transmitter for resistance thermometers (RTD), thermocouples (TC), resistance and voltage transmitters (mv), HART -protocol, for

More information

KINAX SR 719 Programmable Transmitter for Position Feedback

KINAX SR 719 Programmable Transmitter for Position Feedback Position transmitter with NAMUR valve fitting Application The position feedback transmitter KINAX SR 719 (Figs. 1 and 2) is used to measure and transmit linear displacement (stroke) on various types of

More information

Digital Temperature Transmitters Model T12.10, Universally Programmable, Head Mounting Model T12.30, Universally Programmable, Rail Mounting

Digital Temperature Transmitters Model T12.10, Universally Programmable, Head Mounting Model T12.30, Universally Programmable, Rail Mounting Electrical Temperature Measurement Digital Temperature Transmitters Model T12.10, Universally Programmable, Head Mounting Model T12.30, Universally Programmable, Rail Mounting WIKA Data Sheet TE 12.03

More information

itemp PA TMT184 Technical information

itemp PA TMT184 Technical information Technical information itemp PA TMT184 Temperature head transmitter with PROFIBUS-PA interface. Supply and digital communication using PROFIBUS-PA, for installation in a Form B sensor head. Features and

More information

Temperature head transmitter itemp TC TMT 188

Temperature head transmitter itemp TC TMT 188 Technical information TI 077R/24/ae No.: 510 06145 Temperature head transmitter itemp TC TMT 188 Universal head transmitter for thermocouples for an economical, high accuracy temperature monitoring. Fixed

More information

JUMO dtrans T02 Programmable 4-wire Transmitter (Smart Transmitter)

JUMO dtrans T02 Programmable 4-wire Transmitter (Smart Transmitter) JUMO GmbH & Co. KG Delivery address:mackenrodtstraße 14, 36039 Fulda, Germany Postal address: 36035 Fulda, Germany Phone: +49 661 6003-0 Fax: +49 661 6003-607 e-mail: mail@jumo.net Internet: www.jumo.net

More information

Plug-in module SIRAX TV 808, 1 channel Isolating Amplifier unipolar/bipolar

Plug-in module SIRAX TV 808, 1 channel Isolating Amplifier unipolar/bipolar for electrically insulating, amplifying and converting DC signals 0102 II (1) G pplication The purpose of the isolating amplifi er SIRX T 808 (Fig. 1) is to electrically insulate input and output signals,

More information

â Ó itemp TC TMT128 Technical information DIN rail mounted Temperature Transmitter for Thermocouples (TC)

â Ó itemp TC TMT128 Technical information DIN rail mounted Temperature Transmitter for Thermocouples (TC) Technical information itemp TC TMT128 DIN rail mounted Temperature Transmitter for Thermocouples (TC) Application Temperature transmitter with fixed measuring ranges for converting TC input signals into

More information

SITRANS T measuring instruments for temperature

SITRANS T measuring instruments for temperature Overview Our field devices for heavy industrial use HART, Universal 4 to 20 ma, universal Field indicator for 4 to 20 ma signals The temperature transmitter SITRANS TF works where others feel uncomfortable.

More information

Plug-in module SIRAX TI 807 Passive DC signal isolator

Plug-in module SIRAX TI 807 Passive DC signal isolator without power supply, x- and non-x version 0102 II (1) resp. II (2) pplication The signal isolator SIRX TI 807 (Fig. 1) serves to electrically insulate the analogue DC signal in the range 0 20 m which

More information

Description of functions Controller system VR660 / A200R

Description of functions Controller system VR660 / A200R Description of functions Controller system VR660 / A00R Local bus RS VR660/A00R e 56 76-0.07 Camille Bauer AG Aargauerstrasse 7 CH-560 Wohlen/Switzerland Phone + 56 68 Fax + 56 68 5 5 e-mail: info@camillebauer.com

More information

KINAX WT 707 Transmitter for angular position

KINAX WT 707 Transmitter for angular position Ruggedized version pplication The KINX WT 707 (Figs. 1 to 6) converts the angular position of a shaft into a load-independent direct current signal, proportional to the angular position. The unit is contact

More information

Temperature head transmitter itemp PCP TMT 181

Temperature head transmitter itemp PCP TMT 181 Technical information TI 070R/09/en Mat.-Nr.: 510 01110 Temperature head transmitter itemp PCP TMT 181 Universal head transmitter for resistance thermometers (RTD), thermocouples, resistance and voltage

More information

Temperature Measurement

Temperature Measurement Overview Application transmitters can be used in all industrial sectors. Due to their compact size they can be installed in the connection head type B (DIN 4729) or larger. The following sensors/signal

More information

JUMO dtrans T02 Programmable 4-wire Transmitter (Smart Transmitter)

JUMO dtrans T02 Programmable 4-wire Transmitter (Smart Transmitter) JUMO GmbH & Co. KG Delivery address: Mackenrodtstraße 14 36039 Fulda, Germany Postal address: 36035 Fulda, Germany Phone: +49 661 6003-0 Fax: +49 661 6003-607 E-mail: mail@jumo.net Internet: www.jumo.net

More information

C330 / C330X PC-Programmable Universal, 2-wire Transmitter

C330 / C330X PC-Programmable Universal, 2-wire Transmitter C330 / C330X PC-Programmable Universal, 2-wire Transmitter The IPAQ C330 transmitter is a universal, isolated, temperature transmitter with additional voltage and resistance input. Its robust design and

More information

Temperature measurement TMD 832 head transmitter

Temperature measurement TMD 832 head transmitter Technical information TI 062R/09/en Mat.-Nr. 510 00782 Temperature measurement TMD 832 head transmitter SMART head transmitter with HART protocol for RTD, Thermocouple and mv input signals Applications

More information

Temperature Measurement

Temperature Measurement Temperature Measurement SITANS T00 Overview Application SITANS T00 transmitters can be used in all industrial sectors. Their compact design enables simple mounting on standard DIN rails on-site in protective

More information

Universal Intelligent 2-wire DIN Rail Transmitters

Universal Intelligent 2-wire DIN Rail Transmitters Universal Intelligent 2-wire DIN Rail Transmitters IPAQ-L is a universal and intelligent 2-wire DIN rail transmitter for temperature and other measurement applications. IPAQ-LX is the Intrinsic Safe version

More information

SINEAX V604s Programmable multifunctional transmitter

SINEAX V604s Programmable multifunctional transmitter SINAX V60s for direct currents, direct voltages, temperature sensors, teletransmitters or potentiometers SINAX V60s is a multifunctional transmitter for tophat rail assembly with the following main characteristics:

More information

Plug-in module SIRAX TV 808, 1 channel Isolating Amplifier, output Ex or non-ex

Plug-in module SIRAX TV 808, 1 channel Isolating Amplifier, output Ex or non-ex for electrically insulating, amplifying and converting DC signals, also designed for FSK 002 II () G pplication The purpose of the isolating amplifi er SIRX TV 808 (Fig. ) is to electrically insulate input

More information

Isolators A3/1.

Isolators A3/1. Temperature Transmitter Series 9182 > One unit for nearly all temperature sensors indivdually configurable > Signal duplication possible > Galvanic isolation between input, output, power supply and configuration

More information

SINEAX G 537 Transducer for Phase Angle Difference

SINEAX G 537 Transducer for Phase Angle Difference Carrying rail housing P/0 pplication The transducer SINX G 5 (Fig. ) converts the phase angle difference of two synchronised supplies into a load independent DC current or a load independent DC voltage

More information

RMA42. Technical Information

RMA42. Technical Information Technical Information RMA42 Process transmitter with control unit Digital process transmitter for mounting on a top-hat rail for monitoring and visualizing analog measured values Application Plant and

More information

EURAX VC 603 Programmable combined transmitter/alarm unit

EURAX VC 603 Programmable combined transmitter/alarm unit EURX VC 603 for DC currents or voltages, temperature sensors, remote sensors or potentiometers 010 II (1) GD pplication The combined transmitter/alarm unit EURX VC 603 (Fig. 1) converts the input variable

More information

Connection. Input EEx ia IIC. Sense. Fine tuning adjustment. Fine tuning amplifying. Amplifying. Adjustment. Output. Composition

Connection. Input EEx ia IIC. Sense. Fine tuning adjustment. Fine tuning amplifying. Amplifying. Adjustment. Output. Composition Converter Connection 1-channel EEx ia IIC for 4-wire and 6-wire bridges Analogue output 0/4 ma... 20 ma or 4mA...-12mA Full bridge load cells and strain gauges circuit for resistance bridges up to 17 Ω

More information

Temperature Input Module for Zone 1 Series 9482/32

Temperature Input Module for Zone 1 Series 9482/32 www.stahl.de > 8 channels for temperature sensors > Intrinsically safe inputs Ex ia > For Pt-, Ni- and Cu-resistance temperature detectors according to DIN, IEC and GOST in 2-, 3- and 4-wire circuits >

More information

EMBSIN 281 G Power factor transducer

EMBSIN 281 G Power factor transducer EMBSI 8 G Carrying rail housing MBS/SP Application The transducer EMBSI 8 G (Fig. ) measures the power factor between current and voltage of a single or 3-phase balanced network having a sine wave form.

More information

PROGRAMMABLE FIELD TEMPERATURE TRANSMITTER

PROGRAMMABLE FIELD TEMPERATURE TRANSMITTER Configuration Code TM01 Series 642 Programmable HART Field Temperature The Series 642 programmable HART field temperature transmitter is a 2-wire unit with analog output. It includes input for RTDs; resistance

More information

Digital indicator for panel mounting With multi-function input Model DI25

Digital indicator for panel mounting With multi-function input Model DI25 Accessories Digital indicator for panel mounting With multi-function input Model DI25 WIKA data sheet AC 80.02 Applications Plant construction Machine tools Plastics technology and processing Ventilation

More information

TF 02 / TF 02-Ex. Head mounted temperature transmitters, FOUNDATION Fieldbus (H1), Pt 100 (RTD), thermocouples, 1 or 2 independent channels

TF 02 / TF 02-Ex. Head mounted temperature transmitters, FOUNDATION Fieldbus (H1), Pt 100 (RTD), thermocouples, 1 or 2 independent channels TF 0 / TF 0-Ex Head mounted temperature transmitters, FOUNDATION Fieldbus (H), Pt 00 (RTD), thermocouples, or independent channels 0/-8.5 EN Input Resistance thermometer (,, wire circuit) Thermocouples

More information

Multifunction Intelligent 4-wire Isolated Signal Conditioner

Multifunction Intelligent 4-wire Isolated Signal Conditioner Multifunction Intelligent 4-wire Isolated Signal Conditioner IPAQ-4L is a fully universal and intelligent 4- wire (mains powered) transmitter for temperature measurement and signal conditioning applications.

More information

Temperature Transmitter itemp RTD DIN rail TMT 127

Temperature Transmitter itemp RTD DIN rail TMT 127 Technical Information TI 095R/09/en No. 51004790 Temperature Transmitter itemp RTD DIN rail TMT 127 Temperature Transmitter for Pt100 Resistance Thermometer Application Temperature transmitter with fixed

More information

09746E00. ATEX / IECEx NEC 505 NEC 506 NEC 500 Class I Class I Class II Class III Zone Zone Division Ex i

09746E00. ATEX / IECEx NEC 505 NEC 506 NEC 500 Class I Class I Class II Class III Zone Zone Division Ex i Temperature Transmitter Series 9182 www.stahl.de > One unit for nearly all temperature sensors indivdually configurable > Intrinsically safe input [Ex ia] IIC > Signal duplication possible > Galvanic isolation

More information

High-quality digital indicator for panel mounting Model DI35-M, with multi-function input Model DI35-D, with two inputs for standard signals

High-quality digital indicator for panel mounting Model DI35-M, with multi-function input Model DI35-D, with two inputs for standard signals Accessories High-quality digital indicator for panel mounting Model DI35-M, with multi-function input Model DI35-D, with two inputs for standard signals WIKA data sheet AC 80.03 Applications Machine building

More information

FieldIT Temperature Transmitter, rail mounted TH102/TH102-Ex

FieldIT Temperature Transmitter, rail mounted TH102/TH102-Ex Data Sheet 10/-8.54 EN Level 0: Information FieldIT Temperature Transmitter, rail mounted TH102/TH102-Ex HART programmable, Pt 100 (RTD), thermocouples, electrical isolation Resistance thermometer (2,

More information

3 Ex i Isolators. Temperature Transmitter without Output 0/ ma, with Limit Value Contact (Field Circuit Ex i) Type 9182/.

3 Ex i Isolators. Temperature Transmitter without Output 0/ ma, with Limit Value Contact (Field Circuit Ex i) Type 9182/. Ex i Isolators Temperature Transmitter without Output 0/4... 20 ma, with Limit Value Contact Field Circuit Ex i) One unit for nearly all temperature sensors indivdually configurable Intrinsically safe

More information

Isolators A3/1. Temperature Transmitter Field Circuit Non-Ex i Series

Isolators A3/1. Temperature Transmitter Field Circuit Non-Ex i Series Temperature Transmitter Series 9182 > One unit for nearly all temperature sensors indivdually configurable > Signal duplication possible > Galvanic isolation between input, output, power supply and configuration

More information

Technical Information RMA42

Technical Information RMA42 TI00150R/09/EN/05.16 71315973 Products Solutions Services Technical Information RMA42 Process transmitter with control unit Digital process transmitter for monitoring and visualizing analog measured values

More information

3 Ex i Isolators. Temperature Transmitter with Output 0/ ma, without Limit Value Contact (Field Circuit Ex i) Type 9182/.0-5.

3 Ex i Isolators. Temperature Transmitter with Output 0/ ma, without Limit Value Contact (Field Circuit Ex i) Type 9182/.0-5. Ex i Isolators Temperature Transmitter with Output 0/4... 20 ma, without Limit Value Contact Field Circuit Ex i) One unit for nearly all temperature sensors indivdually configurable Intrinsically safe

More information

Assembly. Front view. Parametrization interface. Power Bus

Assembly. Front view. Parametrization interface. Power Bus Temperature Converter Features Assembly 1-channel signal conditioner 24 V DC supply Thermocouple, RTD, potentiometer or mv input Input for PTC thermistor Current and voltage output Line fault (LFD) and

More information

HART field temperature transmitter Models TIF50, TIF52, TIF62

HART field temperature transmitter Models TIF50, TIF52, TIF62 Electrical temperature measurement HART field temperature transmitter Models TIF50, TIF52, TIF62 WIKA data sheet TE 62.01 Applications Plant construction Process engineering General industrial applications

More information

P5201 Universal Programmable Transmitters with Galvanic Isolation

P5201 Universal Programmable Transmitters with Galvanic Isolation Transmitters - KB0288-2012/09 P5201 Universal Programmable Transmitters with Galvanic Isolation One type of transmitter for all regular resistance and thermocouple sensors. Linearized output signal 4 to

More information

C520 / C520X /C520S / C520XS HART Compatible, Universal, Dual-input 2-wire Transmitters

C520 / C520X /C520S / C520XS HART Compatible, Universal, Dual-input 2-wire Transmitters C520 / C520X /C520S / C520XS HART Compatible, Universal, Dual-input 2-wire Transmitters The 520 transmitters are universal, isolated, dual-input temperature transmitters with additional voltage and resistance

More information

Rail mounted Temperature Transmitter TH102/TH102-Ex

Rail mounted Temperature Transmitter TH102/TH102-Ex Data Sheet 10/-8.54 EN Rail mounted Temperature Transmitter TH102/TH102-Ex HART programmable, Pt 100 (RTD), thermocouples, electrical isolation Input Resistance thermometer (2, 3, 4 wire circuit) Thermocouples

More information

Universal Intelligent 2-wire DIN Rail Transmitters

Universal Intelligent 2-wire DIN Rail Transmitters Universal Intelligent 2-wire DIN Rail Transmitters IPAQ-L is a universal and intelligent 2-wire DIN rail transmitter for temperature and other measurement applications. IPAQ-LX is the Intrinsic Safe version

More information

Universal Intelligent 2-wire In-head Transmitters

Universal Intelligent 2-wire In-head Transmitters Universal Intelligent 2-wire In-head Transmitters Actual size IPAQ-H is a universal and intelligent 2-wire In-head transmitter for temperature and other measurement applications. IPAQ-HX is the Intrinsic

More information

Theta 20A / 20V. Technical Data Sheet. Special Features

Theta 20A / 20V. Technical Data Sheet. Special Features Technical Data Sheet Theta 20A / 20V Theta 20A / 20V is used to measure and convert AC Voltage or Current input into a load independent DC current or voltage output signal. Special Features Available in

More information

Transmitter. Configuration Code TM01 Series 440 Programmable RTD Temperature Transmitter. Application Areas. Features and Benefits

Transmitter. Configuration Code TM01 Series 440 Programmable RTD Temperature Transmitter. Application Areas. Features and Benefits Configuration Code TM01 Series 440 Programmable RTD Temperature Transmitter The Series 440 programmable RTD temperature transmitter is a 2-wire transmitter with an analog output. It has measurement input

More information

JUMO dtrans T04 Four-wire Transmitter, settable via DIP switch/pc setup program

JUMO dtrans T04 Four-wire Transmitter, settable via DIP switch/pc setup program JUMO GmbH & Co. KG Delivery address:mackenrodtstraße 14, 36039 Fulda, Germany Postal address: 36035 Fulda, Germany Phone: +49 661 6003-0 Fax: +49 661 6003-607 e-mail: mail@jumo.net Internet: www.jumo.net

More information

Assembly. Front view. Power Rail

Assembly. Front view. Power Rail Thermometer Resistance Repeater Features Assembly 1-channel isolated barrier 24 V DC supply (Power Rail) RTD/resistance input Resistance output Accuracy 0.1 % Front view Removable terminals blue Function

More information

Temperature Measurement Transmitters for mounting in sensor head

Temperature Measurement Transmitters for mounting in sensor head Siemens AG 015 Overview SITANS TH00 two-wire system, universal, HAT Application SITANS TH00 transmitters can be used in all industrial sectors. Due to their compact size they can be installed in the connection

More information

MODEL: M2XU MODEL: M2XU [1][2] [3][4]

MODEL: M2XU MODEL: M2XU [1][2] [3][4] Super-mini Signal Conditioners Mini-M Series UNIVERSAL TRANSMITTER (PC programmable) Functions & Features Accepts direct inputs from various sensors and provides a standard process signal I/O types and

More information

SITRANS T measuring instruments for temperature

SITRANS T measuring instruments for temperature SITRANS T measuring instruments for temperature /2 Product overview /6 Transmitter for mounting in sensor head /6 SITRANS TH100, two-wire system (Pt100) /9 SITRANS TH200, two-wire system universal /15

More information

JUMO dtrans T01 HART / T01T HART / T01 Junior / T01 Ex / T01 HART Ex Programmable 2-wire transmitter

JUMO dtrans T01 HART / T01T HART / T01 Junior / T01 Ex / T01 HART Ex Programmable 2-wire transmitter JUMO GmbH & Co. KG Delivery address: Mackenrodtstraße 14 36039 Fulda, Germany Postal address: 36035 Fulda, Germany Phone: 49 661 60030 Fax: 49 661 6003607 Email: mail@jumo.net Internet: www.jumo.net JUMO

More information

STT 3000 Series STT170 SMART TEMPERATURE TRANSMITTER Models STT171, STT173, STT17H, STT17F, STT17C

STT 3000 Series STT170 SMART TEMPERATURE TRANSMITTER Models STT171, STT173, STT17H, STT17F, STT17C STT 3000 Series STT170 SMART TEMPERATURE TRANSMITTER Models STT171, STT173, STT17H, STT17F, STT17C 6/07 PRODUCT SPECIFICATION SHEET OVERVIEW The Honeywell STT170 series of programmable temperature transmitters

More information

Temperature Transmitters - Head Mounted

Temperature Transmitters - Head Mounted XTH Features - Non-programmable Models Sensor Types: Models for thermocouple Types J, K, or T Models for RTD Type Pt100 3-wire Select from a variety of pre-configured measuring ranges Internal cold junction

More information

STT 3000 Series STT170 SMART TEMPERATURE TRANSMITTER Models STT171, STT173, STT17H, STT17F, STT17C

STT 3000 Series STT170 SMART TEMPERATURE TRANSMITTER Models STT171, STT173, STT17H, STT17F, STT17C STT 3000 Series STT170 SMART TEMPERATURE TRANSMITTER Models STT171, STT173, STT17H, STT17F, STT17C 34-TT-03-07 3/06 PRODUCT SPECIFICATION SHEET OVERVIEW The Honeywell STT170 series of programmable temperature

More information

Head mounted Temperature Transmitter TF02/TF02-Ex

Head mounted Temperature Transmitter TF02/TF02-Ex Data Sheet Head mounted Temperature Transmitter TF0/TF0-Ex FOUNDATION Fieldbus H, Pt 00 (RTD), thermocouples, or independent channels Input Resistance thermometer (-, -, -wire circuit) Thermocouples Resistance

More information

Analogue Temperature Transmitter

Analogue Temperature Transmitter TE 19.01 Electrical Temperature Measurement Analogue Temperature Transmitter Configurable Ranges, Head Mounting for Pt100 Resistance Thermometers for Thermocouples Applications Plant construction Power

More information

JUMO dtrans T01 HART / T01T HART / T01 Junior / T01 Ex / T01 HART Ex Programmable 2-wire transmitter

JUMO dtrans T01 HART / T01T HART / T01 Junior / T01 Ex / T01 HART Ex Programmable 2-wire transmitter JUMO GmbH & Co. KG Delivery address: Mackenrodtstraße 14 36039 Fulda, Germany Postal address: 36035 Fulda, Germany Phone: 49 661 60030 Fax: 49 661 6003607 Email: mail@jumo.net Internet: www.jumo.net JUMO

More information

Temperature Measurement Transmitters for mounting in sensor head

Temperature Measurement Transmitters for mounting in sensor head Siemens AG 015 SITANS TH00 two-wire system, universal Overview Application SITANS TH00 transmitters can be used in all industrial sectors. Due to their compact size they can be installed in the connection

More information

Theta Hz. Technical Data Sheet. Special Features

Theta Hz. Technical Data Sheet. Special Features Technical Data Sheet Theta Hz Theta Hz the transducer is used for frequency measurement. The output signal is proportional to measured frequency and is either load independent DC Current or load independent

More information

OPTITEMP TT 20 Technical Datasheet

OPTITEMP TT 20 Technical Datasheet OPTITEMP TT 20 Technical Datasheet Analog PC-programmable two-wire transmitters for Pt100 Efficient PC-configuration without recalibration Very stable output Very fast response time The documentation is

More information

Temperature transmitter with local display RIT 261

Temperature transmitter with local display RIT 261 Technical Information TI 091R/2/ae Temperature transmitter with local display RIT 261 Universal field mounted transmitter provides an exceptional backlit temperature indication with five large digits and

More information

Temperature transmitter itemp RTD DIN rail TMT 127

Temperature transmitter itemp RTD DIN rail TMT 127 Technical information TI 095R/24/ae Nr. 510 06165 Temperature transmitter itemp RTD DIN rail TMT 127 Pt100 transmitter for an economical, high accuracy temperature monitoring. Fixed range measurement,

More information

Technical Information itemp TMT180

Technical Information itemp TMT180 TI00088R/09/EN/14.16 71315611 Technical Information itemp TMT180 Temperature head transmitter for resistance thermometers Pt100 Configurable using a PC, for installation in a terminal head, form B Application

More information

TR 104, TR 104-Ex Rail mounted Temperature Transmitters

TR 104, TR 104-Ex Rail mounted Temperature Transmitters Data Sheet 10/-8.48-EN Rev. A TR 104, TR 104-Ex Rail mounted Temperature Transmitters Analog, Pt 100 (RTD), fixed measuring ranges Input Resistance thermometer (two-wire and three-wire circuit) Optionally

More information

â itemp Pt100 TMT127 Technical information Pt100 transmitter for DIN rail mounting for high accuracy temperature monitoring

â itemp Pt100 TMT127 Technical information Pt100 transmitter for DIN rail mounting for high accuracy temperature monitoring Technical information itemp Pt100 TMT127 Pt100 transmitter for DIN rail mounting for high accuracy temperature monitoring Application Temperature transmitter with fixed measuring range for converting a

More information

Temperature Transmitters - DIN Rail Mounted

Temperature Transmitters - DIN Rail Mounted XTD Features - Non-programmable Models Sensor Types: Models for thermocouple Types J, K, or T Models for RTD Type Pt100 3-wire Select from a variety of pre-configured measuring ranges Internal cold junction

More information

Digital temperature transmitter with HART protocol Model T32.1S, head mounting version Model T32.3S, rail mounting version

Digital temperature transmitter with HART protocol Model T32.1S, head mounting version Model T32.3S, rail mounting version Electrical temperature measurement Digital temperature transmitter with HART protocol Model T32.1S, head mounting version Model T32.3S, rail mounting version WIKA data sheet TE 32.04 Applications Process

More information

HART Compatible Intelligent 2-wire DIN Rail Transmitters

HART Compatible Intelligent 2-wire DIN Rail Transmitters HART Compatible Intelligent 2-wire DIN Rail Transmitters MESO-L is a Smart and universal 2-wire DIN Rail transmitter for temperature and other measurement applications. MESO-LX is the Intrinsic Safe version

More information