Blue Point Engineering

Transcription

1 DMX Data Analyzer Board nstruction Overview DMX Analyzer - Tester PC Board Design your own enclosure with an analyzer / tester display or add to your existing equipment or system. The DMX Analyzer is a 6 x DMX / DMX LCD back lit data analyzer display unit. The DMX Analyze displays any 4 of channels at a time, and showing the numeric levels currently on those channels in several display formats. Decimal, Hexadecimal, Percentage, or Bar Graph The 4 on-board buttons [ +, -, 0, 00 ] will scroll thru the DMX channels for viewing, by holding down the ' - ' button and pressing 0 or 00 will subtract by 0 or 00. The Stats display shows the packet size, start code, and rate or (frequency). Board also features a dual input selection in programming, if your installation needs a front and rear connection, the user can easily change from the 'A' to 'B' input simply by making a front selection change. The LCD's backlight is easily adjusted with front access software setting for easy changes in those dark control room environments. The auto dim feature allows the user to set the time and dim to value. This is useful if your using battery power. FEATURES NCLUDE: Bar Graph Display (Displays 4 Channels at a Time) Decimal Display, Hexadecimal Display, Percentage Display, Bar Graph Display, and Statistics Display Auto Dim (User Set Timer) Dual nput Option Fully assembled printed circuit board. The PCB assembly consists of boards, the 6 x back lit display, detachable 4 button and contrast board, and the control board. The PCB includes a clear LCD cover that mounts with adhesive strips on your custom enclosure. +VDC input or with the onboard +V regulator, the Analyzer has a +7V ~ +VDC input voltage range. SPECFCATONS: POWER NPUT: +VDC regulated,. x. x 9. connector - center positive. f a regulator option is installed +7VDC ~ +VDC FUSE:.7 ~ Amp Fast Acting X 0 mm POWER USE: Approx: 4mA back light=0, 7mA back light=, 6mA back light=0 & B circuit installed, 40mA back light=, 60mA back light= & B circuit installed. (Auto Dim option available) DATA TYPE: DMX (0Khz) DATA NPUT: DMX - (or ) pin male, Pin - (Shield) Not connected, Pin Data -, Pin Data + DATA OUTPUT: DMX outputs - (or ) pin female 's, Pin - Power supply common, Pin Data -, Pin Data + DMENSONS Approx: PCB s: CPU and LCD boards:.6 W x.7 L x.6 H (including standoffs) CPU and LCD boards with Button board attached:.04 W Button board:.7 W x. L x.9 H Blue Point

2 nstruction DMX Data Analyzer Board - Components / KT Components Handle the PCB with static electricity precautions - touch a CAUTON grounded source to discharge static electricity before touching the PCB anytime. Panel Mounting Stands Optional LED (B) nput ON Front Side View Button Board Display LCD Contrast Connections ( Pin,) of A and B nput Back Side View Power Regulator Power Configuration Jumpers Power Wire Connections Side View Note - Take care not to touch the component pins or the inner pins of the connectors. Electrostatic discharge may cause permanent damage to the unit. Button Board LC Display Blue Point

3 DMX Data Analyzer Board - Setup nstruction POWER NPUT SETTNGS AND CONNECTONS Assemble the power setup harness or power connection cable and attach to PCB (Optional kit- not included) Set the Voltage Regulator Jumpers according to the voltage input that will be used. f +VDC is to be connected set the jumpers to the OFF position. This will disable the regulator and the connected power source will power the PCB directly. f a power source is connected that is in the range of +7VDC ~ +VDC then set the jumpers to the ON position. For example, use this setting for a 6 cell battery pack with.v batteries totaling 9V. NOTE - f a voltage source greater than VDC is used it is recommended to remove and mount the regulator to the metal chassis or a heat sink to dissipate excessive heat. NOTE: DO NOT EXCEED THE VOLTAGE RANGE. DO NOT SOURCE OTHER DEVCES FROM THS PC BOARD. NSURE THAT THE VOLTAGE SOURCE S A REGULATED DC VOLTAGE 7V - VDC Power Harness Suggested Battery Schematic +VDC to Switch Circuit GND to Circuit SC047 GND Power + Battery Connection - Pack Note: Ground is switched by inserting a connector Power Jack Bottom View SC047 REGULATOR + - POWER Jumper Setup Power Connection Fuse. x x 9 mm - VDC POWER HARNESS REGULATOR OFF VDC nput ON 7V to V nput 9 VDC A power supply (regulated) with a. x. x 9. center positive connector Blue Point

4 DMX Data Analyzer Board - Setup M nstruction LAYOUT & WRNG DAGRAM - Determine the / Enclosure Box layout if needed and assemble the DMX connectors to the Box and PCB. (See optional enclosure setup and layout drawing overviews for possible configurations) nput A 4 Panel Mounted DMX nput A and nput B with NO Optional Loop Output -PN (M) DMX nput A- B 0 Ohm Resistor Red Gold M Panel Mounted nput B 4 Neutrik Termination Resistor R = 0 Ω / Watt R -PN (M) NPUT Only Electronic Schematic 0 Ohm Resistor Red Gold Twisted pair Wire 4 AWG Mount connector as desired. Recommended wire: 4 AWG stranded & twisted together. Analyzer Board DMX Wire - 4 AWG Twisted Pair White Wire = Black Wire = Data- () Data+ () Note - Electrostatic discharge may cause permanent damage to the module. Handle the PCB with static electricity precautions. Copyright 0 Blue Point, All Rights Reserved Blue Point

5 DMX Data Analyzer Board - Setup nstruction NPUT- OUTPUT LAYOUT & WRNG DAGRAM - DMX nput A and nput B and Optional Loop Output nput A Optional Loop Output Optional Enclosure Layout Example nput B M Panel Mounted 4 -PN (M) F Panel Mounted 4 -PN (F) 4 M Panel Mounted -PN (M) Twisted pair Wire 4 AWG Neutrik Red Gold 0 Ohm Resistor Analyzer Board Shield Wire = Pin Black Wire = Pin White Wire = Pin Green Wire = Pin 4 Red Wire = Pin Pin-4 Pin- Pin- Pin- Pin- Shield Note - Electrostatic discharge may cause permanent damage to the module. Handle the PCB with static electricity precautions. Mount connector as desired. Recommended wire: 4 AWG stranded & twisted together. Copyright 0 Blue Point, All Rights Reserved Blue Point

6 DMX Data Analyzer Board - Setup Optional - Example LAYOUT nstruction Port B LED FRONT BACK Add clear plastic LCD screen cover between enclosure and LCD module B nput Output A nput Switch Board Mounting 's Neutrik DMX NPUT B Optional Loop Out DMX NPUT A Power Connector Any pin connector manufacture can be used; chassis mount or inline. Lighting Console Alternative DMX Device s Pin - open (Do not connect) Pin - Data - Pin - Data + Pin - open (Do not connect) Pin - Data - Pin - Data + A B A Loop Out Terminator Analyzer DMX Devices - moving heads, LED's, Pars, Relays, Motors, Dimmers, etc. Analyzer PCB NPUT A NPUT B PCB BLOCK DAGRAM CPU PROCESSOR LCD DSPLAY Analyzer Female (x) Neutrik Configuration Examples Male (x) Blue Point

7 DMX Data Analyzer Board - Optional Setup Optional Enclosure Setup EXAMPLE Mounting Front Male Connectors (x) Female Connector (x) nstruction Electronics Enclosure Box Back Back Panel Mounted s (- M) (- F) Front Back Box Mounting Labels Stats Labels nput B + Cnt 00 Setup Power Jack ( Center Positive ) Mount the +V Power Connector using a washer and nut - Label C + Top View Mounting Mounting Mounting OPTONAL B input (LED will light when 'B' Port is selected) Front View Blue Point

8 nstruction DMX Data Analyzer Board - Optional Setup Optional Setup FRONT MPORTANT NOTE - TERMNATE ALL NON LOOP THRU NPUT CONNECTOR(S) BY SOLDERNG A 0 OHM RESSTOR ACROSS PNS AND. BACK Power Connection NPUT- B RECEVE RECEVE (M) - Male Connector Belden DMX Cable Switchcraft - Connectors Belden DMX Cable DMX Wire OUTPUT SEND - 4 AWG Twisted Pair SEND (F) -Female Connector with shielded and rubber cover jacket White Wire = Black Wire = Data- () Data+ () RECEVE RECEVE (M) - Male Connector NPUT - A Blue Point

9 DMX Data Analyzer Board - Setup LAYOUT & WRNG DAGRAM - DMX nput A and nput B and Optional Loop Output nstruction NO ENCLOSURE 0 Ohm -Terminate if not Used RECEVE SEND nput A -PN (M) Optional Loop Output -PN (F) nput B -PN (M) RECEVE Red Gold 0 Ohm Resistor Twisted pair Wire 4 AWG Analyzer Board Shield Wire = Pin Black Wire = Pin White Wire = Pin Green Wire = Pin 4 Red Wire = Pin Pin-4 Pin- Pin- Pin- Pin- Shield Note - Electrostatic discharge may cause permanent damage to the module. Handle the PCB with static electricity precautions. Mount connector as desired. Recommended wire: 4 AWG stranded & twisted together. Copyright 0 Blue Point, All Rights Reserved Blue Point

10 DMX Data Analyzer Board - OPERATON nstruction CONNECTON Connect a power supply into the power input connector. Connect a DMX source into the A or B input. f a loop through connector is installed either terminate with a 0 ohm terminator or loop to other devices. nsure that input A or B is selected in the menu (see operation instructions below), the LCD will display the channels and data on the respective input or no signal if a valid DMX signal is not present. The Analyzer can be connected or inserted anywhere on the DMX daisy chain. OPERATON Once a DMX signal is established, any of the channels and levels can be displayed. To display the desired channel press the + to scroll to a higher channel one channel at a time or - to scroll one lower channel one at a time. Press the 0 or 00 button to scroll in addition to the left most channel in the display by 0 or 00 respectively. By holding the - button and pressing 0 or 00, the display will scroll in subtraction to the left most channel. The levels of each channel are updated several times per second and will display the latest value. To enter the stats menu press the Stats buttons ( + and - ) simultaneously. To escape and return to the DMX channel display, press the Esc (0) button. To enter the setup menu press the Setup buttons (0 and 00 ) simultaneously. On each menu use the + or - button to change the values. Press Next (00) to go to the next menu setting, or press Esc (0) to return exit the setup menu. Note - Esc and Next will permanently store the value set until changed. ( See the Analyzer Menu Flow Charts for setup menu options.) Button Board Channels Values Dsplay Channels Stats menu press Stats buttons ( + and - ) simultaneously To display the desired channel press the + to scroll to a higher channel one channel at a time or - to scroll one lower channel one at a time Values Press the 0 or 00 button to scroll in addition to the left most channel in the display by 0 or 00 respectively. By holding the - button and pressing 0 or 00, the display will scroll in subtraction to the left most channel. SW SW Display Modes SW SW4 0 Esc Setup Stats Next Decimal Display Hexadecimal Display Percentage Display Bar Graph Display Statistics Display DMX Packet - Start - Rate Blue Point

11 nstruction DMX Data Analyzer Board - OPERATON OPTONAL HARDWARE SETUP ( Auto / Voltage Monitor - AVMH) f the analyzer PC board is equipped with optional Dual nput =(DMX A-B nput) Auto Off, and / or optional Voltage Monitor hardware, these settings are software activated by the Equipped settings. The Dual nput option (nput A-B) is determined by the hardware mounted on the main PCB labeled A in and B in, if both C chips are installed then this is a dual input unit. ( nputs canbe monitored, A-B) The optional Battery Auto Off and Voltage Monitor setup is determined by hardware connected to the main PCB J4 connector. f any of these other optional features are installed, update these optional settings by entering the Setup Equipped Menu by holding the + button and power the unit on. On each menu use the + or - button to change the values. Press Next (00) to go to the next menu setting, or press Esc (0) exit the setup menu. Note - Esc and Next will permanently store the value set until changed. The Voltage Threshold setting is a numeric value indicating the voltage level and lower value that will cause the low battery or b to be displayed. This value is factory preset (8) and should stay in a range of 800 (approx. 6.8 Battery Volts). to 07 (approx. 9 Battery Volts). Formula: [ (A *.%) /.00 = X ] or [ (X *.00) /.%) = A ] Where A is the threshold voltage and X is the numeric value. (/4096=.00V per step) (.4V drop across auto switch). NOTE- ACTVATNG SOFTWARE FEATURES WTHOUT THE HARDWARE ATTACHED MAY CAUSE ERRATC BEHAVOR OF THE BOARD. Optional Setup OPTONAL HARDWARE C Chip - C Chip - J4 Optional hardware Component Setup (Shown Not-nstalled) Using Dual nput DMX Data Analyzer Board Features Connect any - DMX source and display any of the DMX channels and the levels currently on those channels, allowing the user to scroll to any channel to view the levels on the respective channels. The (4) buttons: +, -, 0, & 00, allows the user to scroll through the DMX channels for viewing, and displays in either decimal, hex, percentage, or bar graph value. The stats menu displays the packet size, start code, and rate (amount of packets per second) of the selected input. The user can easily select the 'A' or 'B' input simply by a front menu / buttons selection. The LCD's back light setting is also a menu selection and easily adjusted (no tweeker required) in dark control room environments. The Auto Dim feature will automatically change the LCD back light to a user preset value after a user preset timer elapses. Blue Point

12 nstruction DMX Data Analyzer Board - MENU OPERATON DMX ANALYZER MENU FLOW CHARTS and POWER ON Setup 00 NO Dual nput Equipped? YES Select nput A or B Setup Menu (press 0 & 00 ) NO Auto Off Equipped? YES Set Auto Off Feature ON / OFF Setup Equipped Menu (press & hold + power on) Dual nput Equipped? YES / NO Auto Off Equipped? YES / NO Voltage Monitor Equipped? YES / NO nput Voltage Threshold [+/- Value] Exit Set LCD Back Light Value (0 ) Set Display Type: Decimal Hex Percent Graph Set Auto Dim ON / OFF LCD Auto Dim On? ON Set Auto Off Timer ( second to 60 minutes) Set Auto Dim Value (0 ) OFF OFF NO Auto Off ON / OFF ON Set Auto Off Timer ( second to 60 minutes) Voltage Monitor Equipped? YES Set Battery ndicator Feature ON / OFF Display Software Version Exit Blue Point