COM-POWER OPERATION MANUAL ACS W

Transcription

1 COM-POWER OPERATION MANUAL For the ACS W 150 khz to 250 MHz 100W Power Amplifier Page 1 of 15 MANUAL_ACS W Rev. M02.15

2 Table of Contents Important Safety Precautions Introduction..5 Product Specifications Front/Rear Panel Amplifier Operation Page 2 of 15 MANUAL_ACS W Rev. M02.15

3 Important Safety Precautions Safety Symbol Guide ATTENTION Refer Manual WARNING High Voltage Do not attempt to disassemble the instrument. Please contact our service department. AC power input should be within the voltage range specified on the rear panel. Please ensure that the correct fuse is installed prior to applying power for the first time. To avoid electrical shock, the power cord protective grounding conductor must be grounded. In order to protect against fire, replace the fuse with the specified type only. Make sure to disconnect the power cord before replacing the fuse. A blown fuse is indicative of a problem with the instrument. The problem must be repaired before replacing the fuse. It is important to always keep the front panel connectors clean. Disconnect the AC power cord from the instrument before cleaning. Use a soft cloth dipped in a solution of mild detergent and water. Do not spray any liquid onto the unit. Do not use any cleaners containing benzene, toluene, xylene, acetone and/or any other harsh chemicals. Page 3 of 15 MANUAL_ACS W Rev. M02.15

4 Do not exceed +3 dbm into the RF INPUT. Do not place heavy objects on top of the instrument. Avoid any rough handling that could damage the ACS W unit. Use electrostatic discharge precautions while handling and making connections to the ACS W unit. Do not insert wires into the connectors of the ACS W. Make proper connection with mating connectors and/or adapters. Do not block or obstruct the cooling fan vents located on the top, side and rear side of the unit. Page 4 of 15 MANUAL_ACS W Rev. M02.15

5 Introduction The Com-Power model ACS W broadband power amplifier operates from 150 khz to 250 MHz. This amplifier can be used for EMC immunity testing that requires generating electric fields. This small and lightweight amplifier utilizes class AB linear power devices that provide high gain, and wide dynamic range. By employing advanced components, the Com-Power ACS W amplifier is able to achieve high efficiency operation and reliability. Page 5 of 15 MANUAL_ACS W Rev. M02.15

6 Product Specifications Frequency Range 150 khz MHz Power Output: Rated Output 100 watts into 2:1 VSWR Power Protection Limit 140 watts Output 1dB compression No Compression upto 100W Gain 50 db ± 2 db Input for rated output 0 dbm (Typical) Input: Impedance 50 ohms, nominal VSWR 1.7 maximum Modulation on input AM, FM, or pulse modulation Connector Type N-Female (on Front Panel) Output: Impedance 50 ohms, nominal VSWR 1.7 maximum Harmonic distortion 15 dbc (min) at 100 watts Mismatch Tolerance VSWR of 5:1 Connector Type N-Female (on Front Panel) Line Power Single-phase Type: Universal Volts ac, 50/60 Hz, 400 VA Power Fuse: 250V, 5 Amps (T) Page 6 of 15 MANUAL_ACS W Rev. M02.15

7 Display and Interfaces USB Remote Interface Front panel display Continuous monitoring and display of Temperature, Current, Input / Output Power, VSWR and Gain Mechanical: Cooling Requirement Forced air (self contained fans) Size 19 Rack 4U Weight 21.4 kg (47 lb.) Operating Temperature 0 o C to 50 o C Page 7 of 15 MANUAL_ACS W Rev. M02.15

8 Front/Rear Panel Front Panel: RF output ON/OFF switch 2. Indicates RF output is ON when green light is lit 3. LCD display 4. Fault indicators 5. USB interface- for factory programming/maintenance. 6. RF input port- secure all connections required for the 50 ohm system prior to turning on the RF output. Caution: Although it has a auto shutoff in case of input levels above +3 dbm. Application of high power input signal or transients may damage the power amplifier. 7. RF output port- secure all the connections required for the 50 Ohm system prior to turning on the RF output. Page 8 of 15 MANUAL_ACS W Rev. M02.15

9 Caution: High power output present at the output port when unit is operating, which could lead to serious injuries to user. Do not touch the connector when the unit is ON. 8. Handles Rear Panel: Mains power input to unit with inbuilt fuse socket. The power input can be between 100V AC to 250VAC,47-63Hz, 400VA. The unit auto detects the power supply voltage. The fuse provides primary AC circuit protection. In case of failure of Fuse, replace only with the rated fuse {5x 20 mm 250 V, 5A, (T)} 11. AC supply power ON switch 12. Serial number of unit. Page 9 of 15 MANUAL_ACS W Rev. M02.15

10 Amplifier Operation 1. Before turning on the unit, make sure the RF input and output ports on the front panel are connected to their respective 50Ω input/output devices. 2. Turn on power switch on rear panel. The following messages will be displayed on LCD. Page 10 of 15 MANUAL_ACS W Rev. M02.15

11 In normal condition following message will be displayed NOTE: Prior to turning the front panel power switch ON, please ensure that the RF output of the RF signal source connected to the Amplifier input is turned off or below -45 dbm. When the front panel power switch is turned ON, the ACS W performs a self test. ACS W does not allow the presence of an input signal greater than -45 dbm during the self test and the presence of an input signal will automatically disable the output and display the following message until RF input is reduced below -45 dbm. Page 11 of 15 MANUAL_ACS W Rev. M02.15

12 3. Turn on switch from the front panel as shown in picture. Upon successful completion of the self test mode the LCD screen will display the Driver 1 & 2 Current/Temperature, Module Current/Temperature and System Status. Please note that Pin, Pout, SWR and Gain will not be displayed until the amplifier sees an input of -45dBm. 4. When the RF input is applied (in excess of -40 dbm), the front panel LCD displays the actual measured values for Pin, Pout, SWR, and Gain. The current and temperature status of PA and Driver is always displayed regardless of the input state. Page 12 of 15 MANUAL_ACS W Rev. M02.15

13 Displayed indications and their meanings: Driver1 = Driver1 Current/Temperature (Line 1, columns 1/2 on LCD) Driver2 = Driver2 Current/Temperature (Line 2, columns 1/2 on LCD) PA = PA Module Current/Temperature (Line 3, columns 1/2 on LCD) PS = Power Supply status (Line 4 on LCD) Prev = Reflected Power sensed at the RF output (Line 1, column 3 on LCD) Pin = Input Power to the unit (Line 2, column 3 on LCD) Pout = Output Power of the unit (Line 3, column 3 on LCD) Gain = Gain of the unit (Line 4, column 3 on LCD) 5. Before switching off the power from the front panel, make sure the RF output is reduced to a safe level (-50 dbm) or completely disabled. 6. In the event of any fault occurring, the unit will automatically shut down. Page 13 of 15 MANUAL_ACS W Rev. M02.15

14 7. Depending on the nature of the fault the appropriate red LED will be light up and the corresponding fault message will be displayed on front panel LCD. 8. In order to restart the unit, first turn off the front panel switch, and then restart the unit as described in Section 3. Page 14 of 15 MANUAL_ACS W Rev. M02.15

15 9. Please refer to the Diagnostics chart below to check fault conditions SR.#. FAULT LIGHT LIT MESSAGE ON LCD SCREEN FAULT POSSIBLE CAUSE 1 Current 2 Temperature 3 4 Power Supply RF Input / RF Output 5 VSWR PA CURRENT RANGE EXCEEDED OR DRIVER CURRENT RANGE EXCEEDED PA TEMPERATURE RANGE EXCEEDED OR DRIVER TEMPERATURE RANGE EXCEEDED POWER SUPPLY BAD RF INPUT EXCEEDS +3 dbm OR RF OUTPUT EXCEEDS dbm Reflected Power > 85 Watts Indicates that the current through the module exceeds 9.0 Amperes or the driver current exceeds 2.00 Amperes. Indicates that the temperature range of the module or driver has risen higher than 65 C. Indicates that the DC power supply is not working properly. Indicates either input or output power has exceeded internal limit. Indicates that the reflected power to the Power amplifier has exceeded internal limits. * Power limit was exceeded * Mismatch on 50-ohm System * VSWR of the system is too high * Mismatch on 50-ohm system * VSWR of the system is too high * DC power supply failed * AC input zero cross detector failed * Excessive current draw due to device failure. * Input power limit was exceeded. * Output power limit was exceeded. * Check output connection of unit and connected system. Page 15 of 15 MANUAL_ACS W Rev. M02.15