SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005. CKC LABORATORIES, INC rd Drive S.E., Suite A Bothell, WA Steve Behm Phone:

Transcription

1 SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 CKC LABORATORIES, INC rd Drive S.E., Suite A Bothell, WA Steve Behm Phone: ELECTRICAL (EMC) Valid to: January 31, 2011 Certificate Number: In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this laboratory to perform the following Emissions, Immunity, Wireless and Military tests for electrical equipment: The following test sites are accredited for the test descriptions as indicated below: Site C1 EMC Emissions (EU Only) Testing EMC Immunity (Susceptibility) Testing, and Military / Automotive / Aerospace Emissions and Immunity Testing Site C2 EMC Emissions (EU Only) Testing and EMC Immunity (Susceptibility) Testing Site C3 EMC Emissions and Transmitter Characteristics Testing Military / Automotive / Aerospace Emissions Testing Site M1 Military / Automotive / Aerospace Emissions and Immunity Testing Site M3 Military / Automotive / Aerospace Emissions and Immunity Testing The following test standards are accredited to the indicated test site(s): AUSTRALIA / NEW ZEALAND AS/NZS C1, C2 & C3 Information Technology - Telecommunications and Information Exchange between Systems - Open Systems Interconnection - Transport Protocol Identification Mechanism AS/NZS C3 Electromagnetic Compatibility (EMC) - Generic Emission Standard - Residential, Commercial and Light Industry AS/NZS C3 Electromagnetic Compatibility (EMC) - Generic Emission Standard Industrial Environments AS/NZS C1 & C2 Electromagnetic Compatibility (EMC) - Generic Standards. Immunity for Residential, Commercial and Light-Industrial Environments AS/NZS C1 & C2 Electromagnetic Compatibility (EMC) - Part 6-2 Generic Standards Immunity for Industrial Environments (A2LA Cert. No ) revised 09/22/10 Page 1 of 19

2 AUSTRALIA / NEW ZEALAND (CONTINUED) AS/NZS C3 Electromagnetic Compatibility (EMC) Part 6-3 Emission Standard for Residential, Commercial and Light-Industrial Environments AS/NZS C3 Electromagnetic Compatibility (EMC) Part 6-4 Emission Standard for Industrial Environments AS/NZS 4268 C3 Radio Equipment and Systems - Short Range Devices - Limits and Methods of Measurement AS/NZS 4448 C3 Limits and Methods of Measurement of Radio Disturbance Characteristics for the Protection of Receivers used on Board Vehicles AS/NZS CISPR 11 C3 Industrial, Scientific and Medical (ISM) Radio-Frequency Equipment - Electromagnetic Disturbance Characteristics - Limits and Methods of Measurement AS/NZS CISPR 14.1 C3 Electromagnetic Compatibility (EMC) - Requirements for Household Appliances, Electric Tools and Similar Apparatus Emission AS/NZS CISPR 14.2 C1 & C2 Electromagnetic Compatibility (EMC) - Requirements for Household Appliances, Electric Tools and Similar Apparatus - Immunity - Product Family Standard AS/NZS CISPR 22 (Limited to 1GHz) C3 Information Technology Equipment - Radio Disturbance Characteristics - Limits and Methods of Measurement TELCORDIA / BELLCORE GR-499-CORE C1, C2 & C3 Transport Systems Generic Requirements (TSGR) Common Requirements [Sections 14.1, 14.2, 4.3] GR-1089-CORE C1, C2 & C3 Electromagnetic Compatibility (EMC) and Electrical Safety Generic Criteria for Network Telecommunication Equipment [Sections 2, 3 & 4] [Excluding Section 4.7, First and Second Level AC Power Fault Tests] CANADA STANDARD CAPABLE DESCRIPTION OF STANDARD * Indicates on-site test services available for indicated standards BETS-1* C3 Technical Standards and Requirements for Low Power Announce Transmitters in the Frequency Bands 525-1,705 KHz and MHz BETS-4* C3 Technical Standards and Requirements for Television Broadcasting Transmitters BETS-5* C3 Technical Standards and Requirements for AM Broadcasting Transmitters BETS-6* C3 Technical Standards and Requirements for FM Broadcasting Transmitters BETS-7 C3 Technical Standards and Requirements for Radio Apparatus Capable of Receiving Broadcasting BETS-8* C3 Technical Standards and Requirements for FM Transmitters Operating in Small Remote Communities (A2LA Cert. No ) revised 09/24/10 Page 2 of 19

3 CANADA (CONTINUED) BETS-9 C3 Technical Standards and Requirements for Television Transmitters Operating in Small Remote Communities ICES 001 C3 Industrial, Scientific and Medical (ISM) Radio Frequency Generators ICES 003 C3 Digital Apparatus ICES 004 C3 Alternating Current High Voltage Power Systems ICES 005 C3 Radio Frequency Lighting Devices ICES 006 C3 AC Wire Carrier Current Devices (Unintentional Radiators) RSS-102 C3 Evaluation Procedure for Mobile and Portable Radio Transmitters With Respect to Health Canada's Safety Code 6 for Exposure of Humans to Radio Frequency Fields RSS-111 C3 Broadband Public Safety Equipment Operating in the Band MHz RSS-112 C3 Land Mobile and Fixed Equipment Operating in the Band MHz RSS-117 C3 Land and Coast Station Transmitters using A1, A2, A3, A2H, or A3H Emissions Operating in the KHz Band RSS-118 C3 Land and Subscriber Stations: Voice, Data and Tone Modulated, Angle Modulation Radiotelephone Transmitters and Receivers Operating in the Cellular Mobile Bands MHz and MHz RSS-119 C3 Land Mobile and Fixed Radio Transmitters and Receivers, to 960 MHz RSS-123 C3 Low Power Licensed Radiocommunication Devices RSS-125 C3 Land Mobile and Fixed Radio Transmitters and Receivers, to 50.0 MHz, Primarily Amplitude Modulated RSS-127 C3 Air-Ground Equipment Operating in the Bands MHz and MHz RSS-129 C3 800 MHz Dual-Mode CDMA Cellular Telephones RSS-131 C3 Zone Enhancers for the Land Mobile Service RSS-132 C3 800 MHz Cellular Telephones Employing New Technologies RSS-133 C3 2 GHz Personal Communication Services RSS-134 C3 900 MHz Narrowband Personal Communications Services RSS-135 C3 Digital Scanner Receivers RSS-136 C3 Land and Mobile Station Radiotelephone Transmitters and Receivers Operating in the MHz General Radio Service Band RSS-137 C3 Location and Monitoring Service ( MHz) RSS-138 C3 Commercial Shipborne Radar in the MHz, MHz and MHz Bands RSS-139 C3 Advanced Wireless Services Equipment Operating in the Bands MHz and MHz RSS-141 C3 Aeronautical Radiocommunication Equipment in the Frequency Band MHz RSS-142 C3 Narrowband Multipoint Communication Systems in the MHZ and MHZ Bands (A2LA Cert. No ) revised 09/24/10 Page 3 of 19

4 CANADA (CONTINUED) RSS-170 C3 Satellite Mobile Earth Stations RSS-181 C3 Coast and Ship Station Single Sideband Radiotelephone Transmitters and Receivers Operating in the KHz Band RSS-182 C3 Maritime Radio Transmitters and Receivers in the Band MHz RSS-188 C3 Global Maritime Distress and Safety System (GMDSS) RSS-191 C3 Local Multipoint Communication Systems in the 28 GHz Band; Point-to-Point and Point-to-Multipoint Broadband Communication Systems in the 24 GHz and 38 GHz Bands RSS-192 C3 Fixed Wireless Access Equipment Operating in the Band MHz RSS-193 C3 Multipoint and Point-to-Point Communication Systems (MCS) in the Fixed Service Operating in the MHz, MHz and MHz Bands RSS-194 C3 Fixed Wireless Access Equipment Operating in the Band MHz RSS-195 C3 Wireless Communications Service Equipment Operating in the Bands MHz and MHz RSS-196 C3 Point-to-Multipoint Broadband Equipment Operating in the Bands MHz and MHz for Rural Remote Broadband Systems (RRBS) (TV Channels 21 to 51) RSS-197 C3 Wireless Broadband Access Equipment Operating in the Band MHz RSS-199 C3 Broadband Radio Service (BRS) Equipment Operating in the Band MHz RSS-210 C3 Low Power License-exempt Radiocommunication Devices (All Frequency Bands) RSS-213 C3 2 GHz License - Exempt Personal Communications Service Devices (PCS) RSS-215 C3 Analogue Scanner Receivers RSS-220 C3 Devices Using Ultra-Wideband (UWB) Technology RSS-243 C3 Active Medical Implant Communications System Devices in the MHz Band RSS-287 C3 Emergency Position Indicating Radio Beacons (EPIRB), Emergency Locator Transmitters (ELT), Personal Locator Beacons (PLB), and Maritime Survivor Locator Devices (MSLD) RSS-310 C3 Low-power Licence-exempt Radiocommunication Devices (All Frequency Bands) Category II Equipment RSS-GEN C3 General Requirements and Information for the Certification of Radiocommunication Equipment (A2LA Cert. No ) revised 09/24/10 Page 4 of 19

5 EUROPEAN UNION STANDARD CAPABLE DESCRIPTION OF STANDARD EMC Directive 2004/108/EC Standards * Indicates on-site test services available for indicated standards EN C1, C2 & C3 Electromagnetic Compatibility - Product Family Standard For Lifts, Escalators And Passenger Conveyors - Emission EN C1 & C2 Electromagnetic Compatibility - Product Family Standard For Lifts, Escalators And Passenger Conveyors - Immunity EN C1, C2 & C3 Electromagnetic compatibility and radio spectrum matters (ERM); Telecommunication network equipment; Electromagnetic compatibility (EMC) requirements EN C1, C2 & C3 Specification for signaling on low-voltage electrical installations in the frequency range 3 KHz to KHz - Part 1 General requirements, frequency bands and electromagnetic disturbances EN ,2,3 C1, C2 & C3 Specification for signaling on low-voltage electrical installations in the frequency range 3 KHz to KHz - Part 2 Immunity requirements for mains communications equipment and systems operating in the range of frequencies 95 khz to 148,5 khz EN C1, C2 & C3 Cable networks for television signals, sound signals and interactive services - Part 2 Electromagnetic compatibility for equipment EN C1, C2 & C3 Railway applications - Electromagnetic compatibility - Part 1 General EN C1, C2 & C3 Railway applications - Electromagnetic compatibility - Part 3-2 Rolling stock - Apparatus EN C1, C2 & C3 Railway applications - Electromagnetic compatibility - Part 4 Emission and immunity of the signalling and telecommunications apparatus EN C1, C2 & C3 Alarm systems - Part 4 Electromagnetic compatibility - Product family standard: immunity requirements for components of fire, intruder and social alarm systems EN C1, C2 & C3 Electromagnetic compatibility - Electrical apparatus for the detection and measurement of combustible gases, toxic gases or oxygen EN C3 Electromagnetic compatibility (EMC) - Product family standard for machine tools - Part 1 Emissions. EN C1 & C2 Electromagnetic Compatibility (EMC) - Product family standard for machine tools - Part 2 Immunity EN C1, C2 & C3 Industrial, scientific and medical (ISM) radio-frequency equipment - Radio disturbance characteristics - Limits and methods of measurement EN C1,C2 & C3 Sound and television broadcast receivers and associated equipment - Radio disturbance characteristics - Limits and methods of measurement (A2LA Cert. No ) revised 09/24/10 Page 5 of 19

6 EUROPEAN UNION (CONTINUED) EN C1, C2 & C3 Electromagnetic compatibility - Requirements for household appliances, electric tools and similar apparatus - Part 1 Emission EN C1 & C2 Electromagnetic compatibility - Requirements for household appliances, electric tools and similar apparatus - Part 2 Immunity - Product family standard EN C1, C2 & C3 Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment EN C1 & C2 Sound and television broadcast receivers and associated equipment - Immunity characteristics - Limits and methods of measurement EN 55022* (Limited to 1GHz) C1 & C2 Information technology equipment - Radio disturbance characteristics - Limits and methods of measurement EN (2006)* C3 Information technology equipment - Radio disturbance characteristics - Limits and methods of measurement [omits amendment(s)] EN C1 & C2 Information technology equipment - Immunity characteristics - Limits and methods of measurement EN C1, C2 & C3 Electromagnetic compatibility - Product family standard for audio, video, audio-visual and entertainment lighting control apparatus for professional use - Emission EN C1 & C2 Electromagnetic compatibility - Product family standard for audio, video, audio-visual and entertainment lighting control apparatus for professional use - Immunity EN C1, C2 & C3 Automatic Electrical Controls for Household and Similar Use- Part 1 General Requirements [EMC sections only] EN thru9, 11, 13,14,18 C1, C2 & C3 Automatic electrical controls for household and similar use - Part 2 Particular requirements EN C1, C2 & C3 Maritime navigation and radiocommunication equipment and systems - General requirements - Methods of testing and required test results EN C1, C2 & C3 Arc welding equipment - Part 10 Electromagnetic compatibility (EMC) requirements EN C1, C2 & C3 Electromagnetic compatibility (EMC) - Part 3 Limits - Section 2 Limits for harmonic current emissions (equipment input current less than/equal to 16 A per phase) EN C1, C2 & C3 Electromagnetic compatibility (EMC) - Part 3 Limits - Section 3 Limitation of voltage fluctuations and flicker in low-voltage supply systems for equipment with rated current less than or equal to 16 A (A2LA Cert. No ) revised 09/24/10 Page 6 of 19

7 EUROPEAN UNION (CONTINUED) EN C1 & C2 Electromagnetic compatibility (EMC) generic standards - Immunity for residential, commercial and light-industrial environments EN C1 & C2 Electromagnetic compatibility (EMC) - Part 6-2 Generic standards immunity for industrial environments EN C1, C2 & C3 Electromagnetic compatibility (EMC) Part 6-3 Emission standard for residential, commercial and light-industrial environments EN C1, C2 & C3 Electromagnetic compatibility (EMC) Part 6-4 Emission standard for industrial environments EN C1, C2 & C3 Low voltage power supplies, D.C. output - Part 3 Electromagnetic compatibility (EMC) EN C1, C2 & C3 Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 1 General requirements EN thru 5 C1, C2 & C3 Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-1 Particular requirements - Test configurations, operational conditions and performance criteria EN C1 & C2 Equipment for general lighting purposes - EMC immunity requirements EN C1, C2 & C3 Uninterruptible power systems (UPS) - Part 2 Electromagnetic compatibility (EMC) requirements EN C1, C2 & C3 Safety of machinery functional safety of safety related electrical, electronic & programmable control systems (note: only capable of performing EMC testing for section 6.4.3, ref Annex E) R&TTE Directive 99/5/EC Standards (excluding article 3.1a, safety provisions) * Indicates on-site test services available for indicated standards EN C1, C2 & C3 Electromagnetic compatibility (EMC) and Radio spectrum Matters (ERM) - Land Mobile Service - Radio equipment with an internal or external RF connector intended primarily for analogue speech - Part 2 Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive EN C1, C2 & C3 Electromagnetic compatibility (EMC) and Radio spectrum Matters (ERM) - Land mobile service - Radio equipment intended for the transmission of data (and/or speech) using constant or non-constant envelope modulation and having an antenna connector - Part 2 Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive EN C1, C2 & C3 Electromagnetic compatibility (EMC) and Radio spectrum Matters (ERM); Radiotelephone transmitters and receivers for the maritime mobile service operating in VHF bands; Part 2: Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive (A2LA Cert. No ) revised 09/24/10 Page 7 of 19

8 EUROPEAN UNION (CONTINUED) EN C1, C2 & C3 Electromagnetic compatibility and Radio spectrum Matters (ERM) - Radiotelephone transmitters and receivers for the maritime mobile service operating in VHF bands - Part 3 Harmonized EN covering essential requirements of article 3.3 (e) of the R&TTE Directive EN C1, C2 & C3 Electromagnetic compatibility and Radio spectrum Matters (ERM) - Land Mobile Service; Radio equipment transmitting signals to initiate a specific response in the receiver - Part 2 Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive EN C1, C2 & C3 Electromagnetic compatibility and Radio spectrum Matters (ERM) - Short Range Devices (SRD) - Radio equipment to be used in the 25 MHz to 1000 MHz frequency range with power levels ranging up to 500 mw, Part 2 Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive EN C1,C2 &C3 Electromagnetic compatibility and Radio spectrum Matters (ERM) - On-site paging service - Part 2 Harmonized EN under article 3.2 of the R&TTE Directive EN C1, C2 & C3 Electromagnetic compatibility and Radio spectrum Matters (ERM) - Wideband Transmission systems - Data transmission equipment operating in the 2.4 GHz ISM band and using spread spectrum modulation techniques - Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive EN C1, C2 & C3 Electromagnetic compatibility and Radio spectrum Matters (ERM) - Short Range Devices (SRD) - Radio equipment in the frequency range 9 KHz to 25 MHz and inductive loop systems in the frequency range 9 KHz to 30 MHz - Part 2 Harmonized EN under article 3.2 of the R&TTE Directive EN C1,C2 &C3 Electromagnetic compatibility and Radio spectrum Matters (ERM) - Wireless microphones in the 25 MHz to 3 GHz frequency range - Part 2 Harmonized EN under article 3.2 of the R&TTE Directive EN C1, C2 & C3 Electromagnetic compatibility and Radio spectrum Matters (ERM) - Land Mobile Service - Double Side Band (DSB) and/or Single Side Band (SSB) amplitude modulated citizen's band radio equipment - Part 2 Harmonized EN covering essential requirements under article 3.2 of R&TTE Directive EN C1, C2 & C3 Electromagnetic compatibility and Radio spectrum Matters (ERM) - Short range devices - Radio equipment to be used in the 1 GHz to 40 GHz frequency range - Part 2 Harmonized EN under article 3.2 of the R&TTE Directive EN C1, C2 & C3 Electromagnetic compatibility and Radio spectrum Matters (ERM) - Wide band audio links - Part 2 Harmonized EN under article 3.2 of the R&TTE Directive (A2LA Cert. No ) revised 09/24/10 Page 8 of 19

9 EUROPEAN UNION (CONTINUED) EN C1, C2 & C3 Electromagnetic compatibility and Radio spectrum Matters (ERM) - Cordless audio devices in the range 25 MHz to MHz - Consumer radio microphones and in-ear monitoring systems operating in the CEPT harmonized band 863 MHz to 865 MHz - Part 2 Harmonized EN under article 3.2 of the R&TTE Directive EN C1, C2 & C3 Electromagnetic compatibility and Radio spectrum Matters (ERM) - ElectroMagnetic Compatibility (EMC) standard for radio equipment and services - Part 1 Common technical requirements EN thru 32 C1, C2 & C3 Electromagnetic compatibility and Radio spectrum Matters (ERM) - ElectroMagnetic Compatibility (EMC) standard for radio equipment and services Parts 2-32, specific conditions EN C1, C2 & C3 Harmonized EN for Global System for Mobile communications (GSM) - Base Station and Repeater equipment covering essential requirements under article 3.2 of the R&TTE directive EN C1, C2 & C3 Fixed Radio Systems - Multipoint equipment and antennas - Generic harmonized standard for multipoint digital fixed radio systems and antennas covering the essential requirements under article 3.2 of the Directive 1999/5/EC EN C1, C2 & C3 Electromagnetic compatibility and Radio spectrum Matters (ERM) - Digital wireless microphones operating in the CEPT harmonized band 1785 MHz to MHz - Part 2 Harmonized EN under article 3.2 of the R&TTE Directive EN C1, C2 & C3 Broadband Radio Access Networks (BRAN) - 5 GHz high performance RLAN - Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive EN thru 12 C1, C2 & C3 Electromagnetic compatibility and Radio spectrum Matters (ERM) - Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks EN C1, C2 & C3 Electromagnetic compatibility and Radio spectrum Matters (ERM) - Wireless Video Links (WVL) operating in the 1.3 GHz to 50 GHz frequency band - Part 2 Harmonized EN under article 3.2 of the R&TTE Directive EN C1 & C2 Electromagnetic compatibility and Radio spectrum Matters (ERM) - Ultra WideBand (UWB) technologies for communication purposes - Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive EN C1, C2 & C3 Electromagnetic compatibility and Radio spectrum Matters (ERM) - Radio Frequency Identification Equipment operating in the band 865 MHz to 868 MHz with power levels up to 2 W - Part 2 Harmonized EN under article 3.2 of the R&TTE Directive EN C1, C2 & C3 Electromagnetic compatibility and Radio spectrum Matters (ERM) - Short Range Devices (SRD) - Close Range Inductive Data Communication equipment operating at 13,56 MHz - Part 2 Harmonised EN under article 3.2 of the R&TTE Directive (A2LA Cert. No ) revised 09/24/10 Page 9 of 19

10 EUROPEAN UNION (CONTINUED) EN C1, C2 & C3 Electromagnetic compatibility and Radio spectrum Matters (ERM) - Short Range Devices (SRD) using Ultra WideBand (UWB) technology - Location tracking equipment operating in the frequency range from 6 GHz to 8.5 GHz - Part 2 Harmonized EN covering essential requirements of Article 3.2 of the R&TTE Directive EN C1, C2 & C3 Broadband Radio Access Networks (BRAN) 5.8 GHz fixed broadband data transmitting systems - Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive EN 55022* (Limited to 1GHz) C1 & C2 Information technology equipment - Radio disturbance characteristics - Limits and methods of measurement EN (2006)* C3 Information technology equipment - Radio disturbance characteristics - Limits and methods of measurement [omits amendment A1] EN C1, C2 & C3 Electromagnetic compatibility (EMC) - Part 3 Limits - Section 2 Limits for harmonic current emissions (equipment input current less than/equal to 16 A per phase) EN C1, C2 & C3 Electromagnetic compatibility (EMC) - Part 3 Limits - Section 3 Limitation of voltage fluctuations and flicker in low-voltage supply systems for equipment with rated current less than or equal to 16 A EN C1 & C2 Electromagnetic compatibility (EMC) generic standards. Immunity for residential, commercial and light-industrial environments EN C1 & C2 Electromagnetic compatibility (EMC) - Part 6-2 Generic standards immunity for industrial environments EN C1, C2 & C3 Electromagnetic compatibility (EMC) Part 6-3 Emission standard for residential, commercial and light-industrial environments EN C1, C2 & C3 Electromagnetic compatibility (EMC) Part 6-4 Emission standard for industrial environments Medical Directive 93/42/EEC Standards EN C1, C2 & C3 Medical electrical equipment - Part 1-2 General requirements for safety - Collateral standard - Electromagnetic compatibility - Requirements and tests EN C1, C2 & C3 Medical electrical equipment Part 2-2 Particular requirements for the safety of high frequency surgical equipment EN C1, C2 & C3 Medical electrical equipment - Part 2-4 Particular requirements for the safety of cardiac defibrillators [EMC sections only] EN C1, C2 & C3 Medical electrical equipment - Part 2.10 Particular requirements for the safety of nerve and muscle stimulators [EMC sections only] EN C1, C2 & C3 Medical electrical equipment - Part 2-12 Particular requirements for the safety of lung ventilators - Critical care ventilators [EMC sections only] (A2LA Cert. No ) revised 09/24/10 Page 10 of 19

11 EUROPEAN UNION (CONTINUED) EN C1, C2 & C3 Medical electrical equipment - Part 2 Particular requirements for the safety of diagnostic and therapeutic laser equipment [EMC sections only] EN C1, C2 & C3 Medical electrical equipment - Part 2-24 Particular requirements for the safety of infusion pumps and controllers [EMC sections only] EN C1, C2 & C3 Medical electrical equipment - Part 2-34 Particular requirements for the safety, including essential performance, of invasive blood pressure monitoring equipment [EMC sections only] EN C1, C2 & C3 Medical electrical equipment - Part 2-37 Particular requirements for the safety of ultrasonic medical diagnostic and monitoring equipment [EMC sections only] EN C1, C2 & C3 Particular requirements in vitro diagnostic medical equipment Other Standards EN C1, C2 & C3 Electrically Powered Wheelchairs, Scooters And Their Chargers - Requirements And Test Methods [Section 9.8 Only] EN C1 & C2 Radiated electromagnetic field from digital radio telephones - Immunity test (900MHz - 5MHz Keyed Carrier) EN * C1 & C2 Electromagnetic compatibility (EMC) - Part 4-2 Testing and measurement techniques - Electrostatic discharge immunity test EN C1 & C2 Electromagnetic compatibility (EMC) - Part 4-3 Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test EN * C1 & C2 Electromagnetic compatibility (EMC) - Part 4-4 Testing and measurement techniques - Electrical fast transient/burst immunity test EN * C1 & C2 Electromagnetic compatibility (EMC) - Part 4-5 Testing and measurement techniques - Surge immunity test EN * C1 & C2 Electromagnetic compatibility (EMC) - Part 4-6 Testing and measurement techniques - Immunity to conducted disturbances, induced by radio-frequency fields EN * C1 & C2 Electromagnetic compatibility (EMC) - Part 4 Testing and measurement techniques - Section 8 Power frequency magnetic field immunity test basic EMC publication EN * C1 & C2 Electromagnetic compatibility (EMC) - Part 4 Testing and measuring techniques - Section 11 Voltage dips, short interruptions and voltage variations immunity tests Directives Old Approach 75/322/EEC - M1 & C3 2000/2/EC 72/245/EEC /28/EC M1 & C3 On the suppression of radio interference produced by agricultural or forestry tractors (electromagnetic compatibility) On the approximation of the laws of the Member States relating to the suppression of radio interference produced by sparkignition engines fitted to motor vehicles (A2LA Cert. No ) revised 09/24/10 Page 11 of 19

12 IDA SINGAPORE IDA TS CT-CTS C3 Technical specification for cordless telephone and cordless telecommunication systems [excluding dect and phs] IDA TS SRD C3 Technical specification for short range devices IDA TS AR C3 Technical specification for amateur radio equipment IDA TS 3G-BS C3 Technical specification for imt-2000 third generation (3g) cellular base station and repeater system IDA TS WBA C3 Technical specification for wireless broadband access (WBA) equipment IDA TS LMR C3 Technical specification for land mobile radio equipment IDA TS RPG C3 Technical specification for radio pagers (for public paging service) IDA TS UWB C1, C2 & C3 Technical Specification for Ultra Wideband (UWB) Devices IDA TS EMC C1, C2 & C3 EMC requirements for telecommunication equipment IDA TS GMPCS C3 Technical specification for Global Mobile Personal Communication by Satellite (GMPCS) Terminals IDA TS GSM-MT C3 Technical specification for GSM Mobile Terminals IDA TS GSM-BS C3 Technical specification for GSM base station and repeater equipment IDA TS 3G-MT C3 Technical specification for IMT-2000 third generation (3G) cellular mobile terminals INTERNATIONAL STANDARD CAPABLE DESCRIPTION OF STANDARD * Indicates on-site test services available for indicated standards CISPR 11 C3 Industrial, scientific and medical (ISM) radio-frequency equipment - Electromagnetic disturbance characteristics - Limits and methods of measurement CISPR 13 C3 Sound and television broadcast receivers and associated equipment - Radio disturbance characteristics - Limits and methods of measurement CISPR 14-1 C3 Electromagnetic compatibility - Requirements for household appliances, electric tools and similar apparatus - Part 1 Emission CISPR 14-2 C1 & C2 Electromagnetic compatibility - Requirements for household appliances, electric tools, and similar apparatus - Part 2 Immunity - Product Family Standard CISPR 15 C3 Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment CISPR 20 C1, C2 & C3 Sound and television broadcast receivers and associated equipment - Immunity characteristics - Limits and methods of measurement CISPR 22(2006)* C3 Information technology equipment - Radio disturbance characteristics - Limits and methods of measurement CISPR 22(1997) C3 Information technology equipment - Radio disturbance characteristics - Limits and methods of measurement (A2LA Cert. No ) revised 09/24/10 Page 12 of 19

13 INTERNATIONAL (CONTINUED) CISPR 25 C1, C2 & C3 Radio disturbance characteristics for the protection of receivers used on board vehicles, boats, and on devices - Limits and methods of measurement IEC C1, C2 & C3 Medical electrical equipment - Part 1 General requirements for safety 2 Collateral standard - Electromagnetic compatibility - Requirements and tests IEC C1, C2 & C3 Medical electrical equipment Part 2-2 Particular requirements for the safety of high frequency surgical equipment IEC C1, C2 & C3 Electromagnetic compatibility of electrical and electronic installations in ships IEC C1, C2 & C3 Maritime navigation and radiocommunication equipment and systems - General requirements - Methods of testing and required test results IEC * C1 & C2 Electromagnetic compatibility (EMC) - Part 4-2 Testing and measurement techniques - Electrostatic discharge immunity test IEC C1 & C2 Electromagnetic compatibility (EMC) - Part 4-3 Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test IEC * C1 & C2 Electromagnetic compatibility (EMC) - Part 4-4 Testing and measurement techniques - Electrical fast transient/burst immunity test IEC * C1 & C2 Electromagnetic compatibility (EMC) - Part 4-5 Testing and measurement techniques - Surge immunity test IEC * C1 & C2 Electromagnetic compatibility (EMC) - Part 4-6 Testing and measurement techniques - Immunity to conducted disturbances, induced by radio-frequency fields IEC * C1 & C2 Electromagnetic compatibility (EMC) - Part 4 Testing and measurement techniques - Section 8 Power frequency magnetic field immunity test basic EMC publication IEC * C1 & C2 Electromagnetic compatibility (EMC) - Part 4 Testing and measuring techniques - Section 11 Voltage dips, short interruptions and voltage variations immunity tests IEC C1, C2 & C3 Programmable controllers Part 2 Equipment requirements and tests [EMC sections only] IEC C1, C2 & C3 Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 1 General requirements IEC thru 5 C1, C2 & C3 Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-1 Particular requirements - Test configurations, operational conditions and performance criteria IEC C1, C2 & C3 Particular requirements in vitro diagnostic medical equipment IEC C1, C2 & C3 Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 3-1 Immunity requirements for safety-related systems and for equipment intended to perform safety-related functions (functional safety) - General industrial applications (A2LA Cert. No ) revised 09/24/10 Page 13 of 19

14 INTERNATIONAL (CONTINUED) IEC C1, C2 & C3 Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 3-2 Immunity requirements for safety-related systems and for equipment intended to perform safety-related functions (functional safety) - Industrial applications with specified electromagnetic environment IEC C1, C2 & C3 Safety of machinery functional safety of safety related electrical, electronic & programmable control systems (note: only capable of performing EMC testing for section 6.4.3, ref Annex E) ISO M1 & C3 Road vehicles - Electrical disturbances from conduction and coupling - Part 2 Electrical transient conduction along supply lines only M1 & C3 Road vehicles - Electrical disturbances from conduction and coupling - Part 2 Vehicles with nominal 12 V or 24 V supply voltage - Electrical transient transmission by capacitive and inductive coupling via lines other than supply lines M1 & C3 Road vehicles - Component test methods for electrical disturbances from narrowband radiated electromagnetic energy - Part 2 Absorber-lined shielded enclosure M1 & C3 Road vehicles - Component test methods for electrical disturbances from narrowband radiated electromagnetic energy - Part 3 Transverse electromagnetic (TEM) cell M1 & C3 Road vehicles - Component test methods for electrical disturbances from narrowband radiated electromagnetic energy - Part 4 Bulk current injection (BCI) M1 & C3 Road vehicles - Component test methods for electrical disturbances from narrowband radiated electromagnetic energy - Part 8 Immunity to magnetic fields M1 & C3 Earth-moving machinery - Electromagnetic compatibility M1 & C3 Agricultural and forestry machinery - Electromagnetic compatibility - Test methods and acceptance criteria JAPAN STANDARD CAPABLE DESCRIPTION OF STANDARD VCCI V-1 C3 Agreement of voluntary control council for interference by information technology equipment VCCI V-2 C3 Rules for Voluntary control measures VCCI V-3 (up to 6 GHz) C3 Technical Requirements (A2LA Cert. No ) revised 09/24/10 Page 14 of 19

15 KOREA STANDARD CAPABLE DESCRIPTION OF STANDARD RRA NOTICE C3 Type Approval of Telecommunications Terminal Equipment RRA NOTICE C3 Designation and Management of Testing Laboratories for Broadcasting and Communications Equipment KCC NOTICE C1, C2 & C3 Type Official Approval, Type registration, EMC registration for Broadcasting and Communications Equipment. RRL NOTICE C3 Technical requirements for the radio equipment of aeronautical mobile service and aeronautical radio navigation service RRL NOTICE C3 Technical requirements for the radio equipment of telecommunication service RRL NOTICE C3 Conformity assessment procedure for type official approval and type registration of radio equipment. RRL NOTICE C3 Technical requirements for the radio equipment for other services than broadcasting, maritime, aeronautical and telecommunications service. RRL NOTICE C3 Technical requirements for the radio equipment for maritime mobile service & maritime radio navigation service KCC NOTICE C3 Technical requirements for EMI KCC NOTICE C1 & C2 Technical requirements for EMS RRA NOTICE C3 Conformity assessment procedure for electromagnetic interference RRA NOTICE C1 & C2 Conformity assessment procedure for electromagnetic susceptibility KN 11 (2008-5) C3 CISPR 11 (2004-6) KN 13 (2008-5) C3 CISPR 13 (2006-3) KN 14-1 (2008-5) C3 CISPR 14-1 ( ) KN 22 (2008-5) C3 CISPR 22 (2005-4) KN 41 (2008-5) C3 EC directive 95/54 (1995-5) KN 50 (2008-5) C3 IEC ~5 (2000-9) KN (2008-5) C3 EN V1.5.1 ( ) KN (2008-5) C3 EN V1.2.1 (2002-8) KN (2008-5) C3 EN V1.2.1 (2002-8) KN (2008-5) C3 EN V1.3.1 ( ) KN 15 (2008-5) C3 CISPR 15 (2007-1) KN 60 ( )* C3 Conformity assessment procedure for interference of powerline communication equipment KN (2008-5) C1 & C2 IEC (2001-4) KN (2008-5) C1 & C2 IEC (2006-2) KN (2008-5) C1 & C2 IEC (2004-7) KN (2008-5) C1 & C2 IEC ( ) KN (2008-5) C1 & C2 IEC ( KN (2008-5) C1 & C2 IEC (2001-3) KN (2008-5) C1 & C2 IEC (2004-3) (A2LA Cert. No ) revised 09/24/10 Page 15 of 19

16 KOREA (CONTINUED) STANDARD CAPABLE DESCRIPTION OF STANDARD KN (2008-5) C1 & C2 IEC ( ) KN 14-2 (2008-5) C1 & C2 CISPR 14-2 ( ) KN 20 (2008-5) C1 & C2 CISPR 20 (1998-8) KN 24 (2008-5) C1 & C2 CISPR 24 ( ) KN 41 (2008-5) C1 & C2 EC directive 95/54 (1995-5) KN 51 (2008-5) C1 & C2 IEC ~5 (2000-9) KN (2008-5) C1 & C2 EN V1.5.1 ( ) KN (2008-5) C1 & C2 EN V1.2.1 (2002-8) KN (2008-5) C1 & C2 EN V1.2.1 (2002-8) KN (2008-5) C1 & C2 EN V1.3.1 ( ) SAE STANDARD CAPABLE DESCRIPTION OF STANDARD J C1, C3, M1 & M3 Measurement of radiated emissions from integrated circuits - surface scan method (loop probe method) 10 MHz to 3 GHz J551-1 C1 & C3 Performance levels and methods of measurement of electromagnetic compatibility of vehicles, boats (up to 15 m), and machines (16.6 Hz to 18 GHz) J551-2 C1 & C3 Test limits and methods of measurement of radio disturbance characteristics of vehicles, motorboats, and spark-ignited engine- driven devices J551-4 C1 & C3 Test limits and methods of measurement of radio disturbance characteristics of vehicles and devices, broadband and narrowband, 150 KHz to 1000 MHz J551-5 C1 & C3 Performance levels and methods of measurement of magnetic and electric field strength from electric vehicles, broadband, 9 KHz to 30 MHz J C1, MI & M3 Vehicle electromagnetic immunity - off-vehicle source J C1, M1 & M3 Vehicle electromagnetic immunity - on-board transmitter simulation J C1, M1 & (R) vehicle electromagnetic immunity - bulk current injection M3 J C1, M1 & M3 Performance level and methods of measurement of electromagnetic compatibility of vehicles, boats (up to 15 m), and machines 50 Hz to 15 GHz Part 15 vehicle electromagnetic immunity - electrostatic discharge (ESD) J C1, M1 & M3 (R) vehicle electromagnetic immunity - power line magnetic fields J C3 Immunity to radiated electromagnetic fields Bulk current injection (BCI) method J C1,M1 & M2 Immunity to conducted transients on power leads J C3 Electrical interference by conduction and coupling capacitive and inductive coupling via lines other than supply lines J C3 Electromagnetic compatibility measurement procedure for vehicle components part 13 immunity to electrostatic discharge (A2LA Cert. No ) revised 09/24/10 Page 16 of 19

17 SAE (CONTINUED) J C1,M1 & M2 Electrical interference by conduction and coupling - coupling clamp and chattering relay J C1, M1 & M2 Electromagnetic compatibility measurement procedure for vehicle components - Part 22 - Immunity to radiated magnetic J J1455 C1, M1 & M2 C1, M1 & M2 J C1, C2 & C3, M1 & M2 fields Limits and methods of measurement of radio disturbance characteristics of components and modules for the protection of receivers used on board vehicles Joint SAE/TMC recommended environmental practices for electronic equipment design (heavy-duty trucks) [Sections: , , , , , , (except )] (R) measurement of radiated emissions from integrated circuits - tem/wideband tem (GTEM) cell method; tem cell (150 KHz to 1 GHz), wideband tem cell (150 KHz to 8GHz) [up to 1.2GHz] TAIWAN CNS C1, C2 & C3 Specification for radio disturbance and immunity measuring apparatus and methods Part 1 Radio disturbance and immunity measuring apparatus. CNS (up to 6 GHz) C3 Limits and methods of measurement of radio interference characteristics of information technology equipment (ITE) CNS C3 Limits and methods of measurement of radio interference characteristics of sound and television broadcast receiver and associated equipment. CNS C3 Limits and methods of measurement of electromagnetic disturbance characteristics of industrial, scientific and medical (ISM) radio-frequency equipment. UNITED STATES 47 CFR PART 11 C3 Emergency alert system (EAS) 47 CFR PART 15 C3 Radio frequency devices 47 CFR PART 18 C3 Industrial, scientific and medical equipment 47 CFR PART 22 C3 Public mobile services 47 CFR PART 24 C3 Personal communications services 47 CFR PART 25 C3 Satellite communications 47 CFR PART 27 C3 Miscellaneous wireless communication services 47 CFR PART 73 C3 Radio broadcast services 47 CFR PART 74 C3 Experimental radio, auxiliary, and special broadcast and other program distributional services 47 CFR PART 80 C3 Stations in the maritime services 47 CFR PART 87 C3 Aviation services 47 CFR PART 90 C3 Private land mobile radio services 47 CFR PART 95 C3 Personal radio services 47 CFR PART 97 C3 Amateur radio services (A2LA Cert. No ) revised 09/24/10 Page 17 of 19

18 UNITED STATES (CONTINUED) 47 CFR PART 101 C3 Fixed microwave services ANSI RESNA WC VOL.2 C1, C2 & C3 Electrically powered wheelchairs, scooters and their chargers - Requirements and test methods [Section 21 only] DO 160A/B/C/D/E/F C1, C3, Environmental conditions and test procedures of airborne MIL-STD-461A/B/C MIL-STD-462A/B/C MIL-STD-461A/B/C MIL-STD-462A/B/C M1 & M3 C1, C3, M1 & M3 C1, M1 & M3 MIL-STD-461D/E/F C1, C3, M1 & M3 MIL-STD-461D/E/F C1, M1 & M3 equipment [Sections: & 25] Electromagnetic emission and susceptibility requirements for the control of electromagnetic interference [Emissions tests sections: CE01-07, RE01-03] Electromagnetic emission and susceptibility requirements for the control of electromagnetic interference [Susceptibility tests CS01-12, RS01-03, RS06] Electromagnetic emission and susceptibility requirements for the control of electromagnetic interference [Emissions tests sections: CE & CE106, RE ] Electromagnetic emission and susceptibility requirements for the control of electromagnetic interference [Susceptibility tests CS101, CS103, CS104, CS105, CS109, CS114, CS115, CS116, RS101, RS103] Per FCC TCB PROGRAM ROLES AND RESPONSIBILITIES dated February 14, 2008 Section 11 Scope of Accreditation for TCB Laboratory The testing laboratory portion of the TCB shall be accredited to ISO/IEC with a scope of accreditation covering the regulations and measurement procedures listed in table 2.11 It should be noted that further guidance on the measurement techniques to be used for a given regulation may be found in the associated report and order, FCC public notice, FCC bulletin or interpretation found on the FCC KDB. Table 2 ISO/IEC Accredited Laboratory Scope of Accreditation Scope A Unlicensed Radio Frequency Devices A1 A2 A CFR Parts 11 (Emergency Alert System (EAS)), 15 (Radio Frequency Devices) and 18 (Industrial, Scientific, and Medical Equipment) 2. FCC MP-5, (February 1986) FCC Methods of Measurements of Radio Noise Emissions From Industrial, Scientific, and Medical Equipment 3. ANSI C , American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 khz to 40 GHz CFR Part 15, Radio Frequency Devices 2. ANSI C , American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 khz to 40 GHz CFR Part 15, Radio Frequency Devices 2. ANSI C , American National Standard for Methods of Measurement of the Electromagnetic and Operational Compatibility of Unlicensed Personal Communications Services (UPCS) Devices 3. ANSI C , American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 khz to 40GHz (A2LA Cert. No ) revised 09/24/10 Page 18 of 19

19 A CFR Part 15, Radio Frequency Devices 2. ANSI C , American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 khz to 40 GHz Scope B Licensed Radio Service Equipment B CFR Parts 2 (Frequency Allocations and Radio Treaty Matters; General Rules and Regulations), 22 (Public Mobile Services), 24 (Personal Communications Services), 25 (Satellite Communications), and 27 (Miscellaneous Wireless Communications Services) 2. ANSI/TIA-603-C (2004), Land Mobile FM or PM Communications Equipment Measurement and Performance Standards B CFR Parts 2 (Frequency Allocations and Radio Treaty Matters; General Rules and Regulations), 22 (Public Mobile Services), 74 (Experimental Radio Auxiliary, Special Broadcast and Other Program Distributional Services), 90 (Private Land Mobile Radio Services), 95 (Personal Radio Services), and 97 (Amateur Radio Services) 2. ANSI/TIA-603-C (2004), Land Mobile FM or PM Communications Equipment Measurement and Performance Standards B CFR Parts 2 (Frequency Allocations and Radio Treaty Matters; General Rules and Regulations), 80 (Stations in the Maritime Services), and 87 (Aviation Services) 2. ANSI/TIA-603-C (2004), Land Mobile FM or PM Communications Equipment Measurement and Performance Standards B CFR Parts 2 (Frequency Allocations and Radio Treaty Matters; General Rules and Regulations), 27 (Broadband Radio Services (BRS) and Educational Broadband Services (EBS)), 74 (Experimental Radio Auxiliary, Special Broadcast and Other Program Distributional Services), and 101 (Fixed Microwave Services) 2. ANSI/TIA-603-C (2004), Land Mobile FM or PM Communications Equipment Measurement and Performance Standards Scope C Telephone Terminal Equipment C CFR Part 68, Connection of Terminal Equipment to the Telephone Network 2. TIA-968-A (January 15, 2003), Telecommunications -- Telephone Terminal Equipment -- Technical Requirements for Connection of Terminal Equipment to the Telephone Network (Upgrade and Revision of TIA/EIA/IS-968), including amendments: TIA-968-A-1 (September 2, 2003), TIA-968-A-2 (March 7, 2004), TIA-968-A-3 (February 2, 2005), TIA-968-A-4 (March 14, 2007), and TIA-968-A-5 (July 25, 2007). 3. T1.TRQ.6 (January 15, 2002), Technical Requirements Document, SHDSL, HDSL2, HDSL4 Digital Subscriber Line Terminal Equipment to Prevent Harm to the Telephone Network 4. TIA/EIA TSB-31-B (February 1, 1998), Part 68 Rationale and Measurement Guidelines (1998) CKC is accredited to the entirety of Scope A and Scope B as listed above in Table 2 Industry Canada Transmitter & EMC Compliance Testing RSS-GEN, ANSI C63.4 (2003) and specific standard(s). 11 See the FCC equipment authorization web page for links to the referenced measurement techniques. Notes: 1. Limitations for listed standards are indicated by square brackets. 2. Scope excludes protocol sections of applicable standards. 3. Scope includes references to basic standards or test methods specified within the governing standard; consequently, the basic standard references need not be identified on this scope document. (A2LA Cert. No ) revised 09/24/10 Page 19 of 19

20 A2LA has accredited CKC LABORATORIES, INC. Bothell, WA for technical competence in the field of Electrical Testing This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated 8 January 2009). Presented this 20 th day of April President & CEO For the Accreditation Council Certificate Number Valid to January 31, 2011 For the tests or types of tests to which this accreditation applies, please refer to the laboratory s Electrical Scope of Accreditation.