KA224/KA224A, KA324/KA324A, KA2902
|
|
- Kathleen O’Brien’
- 6 years ago
- Views:
Transcription
1 KA224/KA224A, KA324/KA324A, KA2902 Quad Operational Amplifier Features Internally Frequency Compensated for Unity Gain Large DC Voltage Gain: 100dB Wide Power Supply Range: KA224 / KA224A, KA324 / KA324A : 3V~32V (or ±1.5 ~ 16V) KA2902: 3V~26V (or ±1.5V ~ 13V) Input Common Mode Voltage Range Includes Ground Large Output Voltage Swing: 0V to -1.5V Power Drain Suitable for Battery Operation Description The KA324 series consist of four independent, high gain, internally frequency compensated operational amplifiers which were designed specifically to operate from a single power supply over a wide voltage range. Operation from split power supplies is also possible so long as the difference between the two supplies is 3 volts to 32 volts. Application areas include transducer amplifier, DC gain blocks and all the conventional OP Amp circuits which now can be easily implemented in single power supply systems. 1 1 Internal Block Diagram OUT OUT4 IN1 (-) IN1 (+) _ _ IN4 (-) IN4 (+) 4 11 GND IN2 (+) 5 _ + + _ 10 IN3 (+) IN2 (-) IN3 (-) OUT2 7 8 OUT3 Rev Fairchild Semiconductor Corporation
2 Schematic Diagram (One Section Only) Q5 Q6 Q12 Q17 Q19 Q20 IN(-) Q1 Q2 Q3 Q4 C1 Q18 R1 IN(+) Q11 R2 OUTPUT Q21 Q7 Q10 Q15 Q8 Q9 Q13 Q14 Q16 GND Absolute Maximum Ratings Parameter Symbol KA224/KA224A KA324/KA324A KA2902 Unit Power Supply Voltage ±16 or 32 ±16 or 32 ±13 or 26 V Differential Input Voltage VI(DIFF) V Input Voltage VI -0.3 to to to +26 V Output Short Circuit to GND Vcc 15V, TA=25 C(One Amp) - Continuous Continuous Continuous - Power Dissipation, TA=25 C Thermal Data PD Operating Temperature Range TOPR -25 ~ ~ ~ +85 C Storage Temperature Range TSTG -65 ~ ~ ~ +150 C Parameter Symbol Value Unit Thermal Resistance Junction-Ambient Max Rθja C/W mw 2
3 Electrical Characteristics ( = 5.0V, VEE = GND, TA = 25 C, unless otherwise specified) KA224 KA324 KA2902 Parameter Symbol Conditions Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Input Offset Voltage Input Offset Current Input Bias Current Input Common Mode Voltage Range Supply Current Large Signal Voltage Gain Output Voltage Swing Common- Mode Rejection Ratio Power Supply Rejection Ratio Channel Separation Short Circuit to GND Output Current Differential Input Voltage VIO VCM=0V to -1.5V VO(P) = 1.4V, RS= 0Ω (Note1) Note: 1. =30V for KA224 / KA224A, KA324 / KA324A, = 26V for KA This parameter, although guaranteed, is not 100% tested in production. Unit mv IIO VCM =0V na IBIAS VCM =0V na VI(R) Note1 0 - ICC GV RL =, = 30V (KA2902, =26V) ma RL =, = 5V ma = 15V, RL=2kΩ VO(P) = 1V to 11V V/mV RL = 2kΩ V VO(H) Note1 RL =10kΩ V VO(L) = 5V, RL=10kΩ mv CMRR db PSRR db CS f = 1kHz to 20kHz (Note2) db ISC = 15V ma ISOURCE ISINK VI(+) = 1V, VI(-) = 0V = 15V, VO(P) = 2V VI(+) = 0V, VI(-) = 1V = 15V VO(P) = 2V VI(+) = 0V, VI(-) = 1V = 5V VO(R) = 200mV ma ma µa VI(DIFF) V V 3
4 Electrical Characteristics (Continued) ( = 5.0V, VEE = GND, unless otherwise specified) The following specification apply over the range of -25 C TA +85 C for the KA224; and the 0 C TA +70 C for the KA324 ; and the -40 C TA +85 C for the KA2902 Parameter Symbol Conditions Input Offset Voltage Input Offset Voltage Drift Input Offset Current Input Offset Current Drift Input Bias Current Input Common Mode Voltage Range Large Signal Voltage Gain Output Voltage Swing Output Current Differential Input Voltage VIO VICM = 0V to -1.5V VO(P) = 1.4V, RS = 0Ω (Note1) KA224 KA324 KA2902 Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit mv VIO/ T RS = 0Ω (Note2) IIO VCM = 0V na IIO/ T RS = 0Ω (Note2) IBIAS VCM = 0V na VI(R) Note1 0 - GV = 15V, RL = 2.0kΩ VO(P) = 1V to 11V RL = 2kΩ V VO(H) Note1 RL = 10kΩ V VO(L) = 5V, RL= 10kΩ mv ISOURCE ISINK VI(+) = 1V, VI(-) = 0V = 15V, VO(P) = 2V VI(+) = 0V, VI(-) = 1V = 15V, VO(P) = 2V µv/ C pa/ C V V/ mv ma ma VI(DIFF) V Note: 1. =30V for KA224/KA224A, KA324/KA324A, = 26V for KA These parameters, although guaranteed, are not 100% tested in production. 4
5 Electrical Characteristics (Continued) ( = 5.0V, VEE = GND, TA=25 C, unless otherwise specified) Parameter Symbol Conditions KA224A KA324A Min. Typ. Max. Min. Typ. Max. Unit VCM = 0V to -1.5V Input Offset Voltage VIO VO(P) = 1.4V, RS = 0Ω mv (Note1) Input Offset Current IIO VCM = 0V na Input Bias Current IBIAS VCM = 0V na Input Common-Mode Voltage Range VI(R) Note1 0 - Note: 1. =30V for KA224 / KA224A, KA324 / KA324A 2. This parameter, although guaranteed, is not 100% tested in production Supply Current ICC = 30V, RL = ma = 5V, RL = ma Large Signal Voltage Gain GV = 15V, RL= 2kΩ VO(P) = 1V to 11V V/mV RL = 2kΩ V VO(H) Note1 Output Voltage Swing RL = 10kΩ V VO(L) = 5V, RL= 10kΩ mv Common-Mode Rejection Ratio CMRR db Power Supply Rejection Ratio PSRR db Channel Separation CS f = 1kHz to 20kHz (Note2) db Short Circuit to GND ISC = 15V ma ISOURCE VI(+) = 1V, VI(-) = 0V = 15V, VO(P) = 2V ma VI(+) = 0V, VI(-) = 1V Output Current ma = 15V, VO(P) = 2V ISINK VI(+) = 0v, VI(-) = 1V µa = 5V, VO(P) = 200mV Differential Input Voltage VI(DIFF) V V 5
6 Electrical Characteristics (Continued) ( = 5.0V, VEE = GND, unless otherwise specified) The following specification apply over the range of -25 C TA + 85 C for the KA224A; and the 0 C TA +70 C for the KA324A Parameter Symbol Conditions Note: 1. =30V for KA224A and KA324A. 2. These parameters, although guaranteed, are not 100% tested in production. KA224A KA324A Min. Typ. Max. Min. Typ. Max. Input Offset Voltage VIO VCM = 0V to -1.5V VO(P) = 1.4V, RS = 0Ω mv (Note1) Input Offset Voltage Drift VIO/ T RS = 0Ω (Note2) µv/ C Input Offset Current IIO VCM = 0V na Input Offset Current Drift IIO/ T RS = 0Ω (Note2) pa/ C Input Bias Current IBIAS VCM = 0V na Input Common-Mode Voltage Range VI(R) Note Large Signal Voltage Gain GV = 15V, RL= 2.0kΩ V/mV Output Voltage Swing -2.0 Unit RL = 2kΩ V VO(H) Note1 RL = 10kΩ V VO(L) = 5V, RL= 10kΩ mv VI(+) = 1V, VI(-) = 0V ISOURCE mv = 15V, VO(P) = 2V Output Current VI(+) = 0V, VI(-) = 1V ISINK ma = 15V, VO(P) = 2V Differential Input Voltage VI(DIFF) V V 6
7 Typical Performance Characteristics Supply Voltage(v) Figure 1. Input Voltage Range vs Supply Voltage Temperature Tj ( C) Figure 2. Input Current vs Temperature Supply Voltage (V) Figure 3. Supply Current vs Supply Voltage Supply Voltage (V) Figure 4. Voltage Gain vs Supply Voltage Frequency (Hz) Figure 5. Open Loop Frequency Response Frequency (Hz) Figure 6. Common mode Rejection Ratio 7
8 Typical Performance Characteristics (Continued) Figure 7. Voltage Follower Pulse Response Figure 8. Voltage Follower Pulse Response (Small Signal) Figure 8. Large Signal Frequency Response Figure 9. Output Characteristics vs Current Sourcing Figure 10. Output Characteristics vs Current Sinking Figure 11. Current Limiting vs Temperature 8
9 Mechanical Dimensions Package Dimensions in millimeters 6.40 ± ± ( ) #1 # MAX 0.46 ± ± ± ± ± ±0.004 #7 # ± ± MIN MAX 3.30 ± ± ~
10 Mechanical Dimensions (Continued) Package Dimensions in millimeters 1.55 ± ±0.004 MIN ( ) #1 # MAX 8.56 ± ± #7 # ± ± MAX ± ±0.008 MAX0.10 MAX ± ± ~8 10
11 Ordering Information Product Number Package Operating Temperature KA324 KA324A KA324D KA324AD 0 ~ +70 C KA224 KA224A KA224D KA224AD -25 ~ +85 C KA2902 KA2902D -40 ~ +85 C 11
12 DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. 11/19/02 0.0m 001 Stock#DSxxxxxxxx 2002 Fairchild Semiconductor Corporation
LM324/LM324A, LM2902/LM2902A
www.fairchildsemi.com LM324/LM324A, LM2902/LM2902A Quad Operational Amplifier Features Internally Frequency Compensated for Unity Gain Large DC Voltage Gain: 100dB Wide Power Supply Range: LM324/LM324A
More informationLM2904,LM358/LM358A,LM258/ LM258A
LM2904,LM358/LM358A,LM258/ LM258A Dual Operational Amplifier www.fairchildsemi.com Features Internally Frequency Compensated for Unity Gain Large DC Voltage Gain: 100dB Wide Power Supply Range: LM258/LM258A,
More informationKA3303/KA3403. Quad Operational Amplifier. Features. Description. Internal Block Diagram.
Quad Operational Amplifier www.fairchildsemi.com Features Output voltage can swing to GND or negative supply Wide power supply range; Single supply of 3.0V to 36V Dual supply of ±1.5V to ±18V Electrical
More informationKA741. Single Operational Amplifier. Features. Description. Internal Block Diagram.
Single Operational Amplifier www.fairchildsemi.com Features Short circuit protection Excellent temperature stability Internal frequency compensation High Input voltage range Null of offset Description
More informationKA741/KA741E. Single Operational Amplifier. Features. Description. Internal Block Diagram.
Single Operational Amplifier www.fairchildsemi.com Features Short circuit protection Excellent temperature stability Internal frequency compensation High Input voltage range Null of offset Description
More informationCopyright Each Manufacturing Company.
Free DataSheet Search and Download Site. Free electronic engineering tool that enables you to locate product datasheets from hundreds of electronic component manufacturers worldwide. Copyright Each Manufacturing
More informationIs Now Part of To learn more about ON Semiconductor, please visit our website at
Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC
More informationLM348. Quad Operational Amplifier. Features. Description. Internal Block Diagram.
Quad Operational Amplifier www.fairchildsemi.com Features LM741 OP Amp operating characteristics Low supply current drain Class AB output stage-no crossover distortion Pin compatible with the LM324 Low
More informationKA4558. Dual Operational Amplifier. Features. Descriptions. Internal Block Diagram.
Dual Operational Amplifier www.fairchildsemi.com Features No frequency compensation required. No latch up. Large common mode and differential voltage range. Parameter tracking over temperature range. Gain
More informationLM1458/LM1458C. Dual Operational Amplifier. Features. Description. Internal Block Diagram.
Dual Operational Amplifier www.fairchildsemi.com Features Internal frequency compensation Short circuit protecion Large common mode and differential voltage range No latch up Low power consumption Description
More informationUTC UNISONIC TECHNOLOGIES CO., LTD. 1 LINEAR INTEGRATED CIRCUIT QUAD OPERATIONAL AMPLIFIERS
UTC LM QUAD OPERATIONAL AMPLIFIERS DESCRIPTION The UTC LM consists of four independent, high gain internally frequency compensated operational amplifiers which are designed specifically to operated from
More informationLM311. Single Comparator. Features. Description. Internal Block Diagram.
Single Comparator www.fairchildsemi.com Features Low input bias current : 250nA (Max) Low input offset current : 50nA (Max) Differential Input Voltage : ±30V Power supply voltage : single 5.0V supply to
More informationKA334. Dual Power Operational Amplifier. Description. Features. Applications. Internal Block Diagram VCC OUT1 OUT2. NC Vcc VEE/GND GND VEE/GND GND GND
Dual Power Operational Amplifier www.fairchildsemi.com Features Output Current upto 0.7A Operates at Low Voltage (VS(MIN)=4V) Low Saturation Voltage (Ip=0.5A, VO=.5V) Thermal Shutdown (TSD=0 C) Ground
More informationL272. Dual Power Operational Amplifier. Description. Features. Applications. Internal Block Diagram VCC OUT1 OUT2 VEE/GND VEE/GND GND GND GND NC IN1-
Dual Power Operational Amplifier www.fairchildsemi.com Features Output Current upto 0.7A Operates at Low Voltage (VS(MIN)=4V) Low Saturation Voltage (Ip=0.5A, VO=1.5V) Thermal Shutdown (TSD=160 C) Ground
More informationL272/L272A Dual Power Operational Amplifier
L272/L272A Dual Power Operational Amplifier www.fairchildsemi.com Features Output Current up to 0.7A Operates at Low Voltage (VS(MIN) = 4V) Low Saturation Voltage (Ip = 0.5A, VO = 1.5V) Thermal Shutdown
More informationLM2903,LM393/LM393A,LM293A
Dual Differential Comparator www.fairchildsemi.com Features Single Supply Operation: 2V to 36V Dual Supply Operation: 1V to 18V Allow Comparison of Voltages Near Ground Potential Low Current Drain 800
More informationKA7500B. SMPS Controller. Features. Description. Internal Block Diagram.
SMPS Controller www.fairchildsemi.com Features Internal Regulator Provides a Stable 5V Reference Supply Trimmed to 5% Uncommitted Output TR for 200mA Sink or Source Current Output Control For Push-Pull
More informationUC3525A. SMPS Controller. Features. Description. Internal Block Diagram.
SMPS Controller www.fairchildsemi.com Features 5V ± 1% Reference Oscillator Sync terminal Internal Soft Start Deadtime Control Under-Voltage Lockout Description UC3525A is a monolithic integrated circuit
More informationKA7500C. SMPS Controller. Features. Description. Internal Block Diagram.
SMPS Controller www.fairchildsemi.com Features Internal regulator provides a stable 5V reference supply trimmed to ±1 % Accuracy. Uncommitted output TR for 200mA sink or source current Output control for
More informationQuad ground sense operational amplifier
Quad ground sense operational amplifier BAA / BAAF / BAAFV The BAA, BAAF, and BAAFV are monolithic ICs with four built-in operational amplifiers featuring internal phase compensation. Either a dual or
More informationQuad Ground Sense Operational Amplifier. The CO324 is monolithic IC with four built-in operational amplifiers featuring internal phase compensation.
The CO4 is monolithic IC with four built-in operational amplifiers featuring internal phase compensation. Either a dual or single power supply can be driven, and these products can be driven by a digital
More informationDual operational amplifier
Dual operational amplifier The BA8, BA8F, and BA8N are monolithic ICs with two operational amplifiers featuring low power consumption and internal phase compensation mounted on a single silicon chip. These
More informationIs Now Part of To learn more about ON Semiconductor, please visit our website at
Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC
More informationLow Power LM321N5. Low Power Single Operational Amplifier. General Description. Features. Applications
Low Power Single Operational Amplifier Low Power Single Operational Amplifier General Description The is a high gain and internally frequency compensated operational amplifier specifically designed to
More informationKA76L05. Low Dropout Voltage Regulator. Description. Features. Internal Block Diagram.
Low Dropout Voltage Regulator www.fairchildsemi.com Features Limited input voltage and high efficiency. Internal thermal over load protection. 6V load dump protection. Output current up to.1a. Description
More informationLM317M. 3-Terminal 0.5A Positive Adjustable Regulator. Features. Description. Internal Block Diagram.
www.fairchildsemi.com 3-Terminal 0.5A Positive Adjustable Regulator Features Output Current in Excess of 0.5A Output Adjustable Between 1.2V and 37V Internal Thermal Overload Protection Internal Short
More informationRC4741 General Purpose Operation Amplifier
General Purpose Operation Amplifier www.fairchildsemi.com Features Unity gain bandwidth 3. MHz High slew rate 1.6 V/mS Low noise voltage 9 nv/öhz Input offset voltage. mv Input bias current 6 na Indefinite
More informationUC3842/UC3843/UC3844/UC3845
SMPS Controller www.fairchildsemi.com Features Low Start up Current Maximum Duty Clamp UVLO With Hysteresis Operating Frequency up to 500KHz Description The UC3842/UC3843/UC3844/UC3845 are fixed frequencycurrent-mode
More informationKA431/KA431A/KA431L. Programmable Shunt Regulator. Features. Description. Internal Block Diagram.
www.fairchildsemi.com KA431/KA431A/KA431L Programmable Shunt Regulator Features Programmable output voltage to 36 volts Low dynamic output impedance 0.20 typical Sink current capability of 1.0 to 100mA
More informationKA78RL00. Adjustable Micro Power Voltage Regulator. Description. Features. Internal Block Diagram.
Adjustable Micro Power Voltage Regulator www.fairchildsemi.com Features Low Quiescent Current Low Dropout Voltage Low Temperature Coefficient Tight Line and Load Regulation Guaranteed 100mA Output Current
More informationFAN7527B. Power Factor Correction Controller. Features. Description. Applications.
Power Factor Correction Controller www.fairchildsemi.com Features Internal start-up timer Internal R/C filter eliminates the need for an external R/C filter Very precise adjustable output over voltage
More informationLM431SA/LM431SB/LM431SC
Programmable Shunt Regulator www.fairchildsemi.com Features Programmable Output Voltage to 36 Volts Low Dynamic Output Impedance.2 Typical Sink Current Capability of 1. to 1mA Equivalent FullRange Temperature
More informationRC4136 General Performance Quad 741 Operational Amplifier
RC General Performance Quad 7 Operational Amplifier www.fairchildsemi.com Features Unity gain bandwidth MHz Short circuit protection No frequency compensation required No latch-up Large common mode and
More informationLM392/LM2924 Low Power Operational Amplifier/Voltage Comparator
LM392/LM2924 Low Power Operational Amplifier/Voltage Comparator General Description The LM392 series consists of 2 independent building block circuits. One is a high gain, internally frequency compensated
More informationQuad operational amplifier
Quad operational amplifier BA7 / BA7F The BA7 and BA7F are monolithic ICs with four operational amplifiers featuring internal phase compensation mounted on a single silicon chip. Either a dual or single
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. LM392 Low Power Operational Amplifier/Voltage Comparator General Description
More informationMC78XXE. 3-Terminal 1A Positive Voltage Regulator. Features. Description. Internal Block Digram.
-Terminal A Positive Voltage Regulator www.fairchildsemi.com Features Current up to A Voltages of 5, V Thermal Overload Protection Short Circuit Protection Transistor Safe Operating Area Protection Description
More informationMC78XX/LM78XX. 3-terminal 1A positive voltage regulator. Features. Description. Internal Block Digram.
www.fairchildsemi.com 3-terminal 1A positive voltage regulator Features Current up to 1A Voltages of 5, 6, 8, 9, 10, 11, 12, 15, 18, 24V Thermal Overload Protection Short Circuit Protection Transistor
More informationKM4110/KM mA, Low Cost, +2.7V & +5V, 75MHz Rail-to-Rail Amplifiers
+ + www.fairchildsemi.com KM411/KM41.5mA, Low Cost, +.7V & +5V, 75MHz Rail-to-Rail Amplifiers Features 55µA supply current 75MHz bandwidth Power down to I s = 33µA (KM41) Fully specified at +.7V and +5V
More informationLM725 Operational Amplifier
LM725 Operational Amplifier General Description The LM725/LM725A/LM725C are operational amplifiers featuring superior performance in applications where low noise, low drift, and accurate closed-loop gain
More informationBIPOLAR ANALOG INTEGRATED CIRCUIT
DATA SHEET BIPOLAR ANALOG INTEGRATED CIRCUIT µpc4 LOW POWER QUAD OPERATIONAL AMPLIFIER DESCRIPTION The µpc4 is a quad operational amplifier which is designed to operate from a single power supply over
More informationLM837 Low Noise Quad Operational Amplifier
LM837 Low Noise Quad Operational Amplifier General Description The LM837 is a quad operational amplifier designed for low noise, high speed and wide bandwidth performance. It has a new type of output stage
More informationS-19610A MINI ANALOG SERIES FOR AUTOMOTIVE 125 C OPERATION CMOS OPERATIONAL AMPLIFIER. Features. Applications. Package.
www.sii-ic.com MINI ANALOG SERIES FOR AUTOMOTIVE 15 C OPERATION CMOS OPERATIONAL AMPLIFIER SII Semiconductor Corporation, 14 The mini-analog series is a group of ICs that incorporate a general purpose
More informationLM2904WH. Low-power dual operational amplifier. Description. Features
Low-power dual operational amplifier Datasheet - production data MiniSO8 Wafer form SO8 Features Frequency compensation implemented internally Large DC voltage gain: 100 db Wide bandwidth (unity gain:
More informationUC3842/UC3843/UC3844/UC3845
SMPS Controller www.fairchildsemi.com Features Low Start Up Current Maximum Duty Clamp UVLO With Hysteresis Operating Frequency Up To 500KHz Description The UC3842/UC3843/UC3844/UC3845 are fixed frequency
More informationUNISONIC TECHNOLOGIES CO., LTD
UNISONIC TECHNOLOGIES CO., LTD DUAL OPERATIONAL AMPLIFIER DESCRIPTION The UTC LM358 consists of two independent high gain, internally frequency compensated operational amplifier. It can be operated from
More informationFAN7527. Power Factor Correction Controller. Features. Description. Applications.
Power Factor Correction Controller www.fairchildsemi.com Features Internal Startup Timer Internal R/C filter eliminates the Need for an External R/C filter Very Precise Adjustable Output Over Voltage Protection
More informationNJM324C. Low power quad operational amplifiers
Low power quad operational amplifiers Features Wide gain bandwidth:.mhz typ. Input common-mode voltage range includes ground Large voltage gain:db typ. Very low supply current per amplifier:ua typ. Low
More informationFAN CH Motor Driver. Features. Description. Typical Application. Ordering Information.
6-CH Motor Driver www.fairchildsemi.com Features 5-CH Balanced Transformerless (BTL) Driver 1-CH (Forward Reverse) Control DC Motor Driver Operating Supply Voltage (4.5 V ~ 13.2 V) Built in Thermal Shut
More informationKA378R33. Low Dropout Voltage Regulator. Features. Description. Internal Block Diagram.
www.fairchildsemi.com KA378R33 Low Dropout Voltage Regulator Features 3A / 3.3V Output low dropout voltage regulator TO22 Full-Mold package (4PIN) Overcurrent protection, Thermal shutdown Overvoltage protection,
More informationKA7552A/KA7553A. SMPS Controller. Features. Description. Internal Block Diagram.
SMPS Controller www.fairchildsemi.com Features Builtin drive circuits for direct connection power MOSFET (lo = ±1.5A) Wide operating frequency range (5kHz ~ 600kHz) Pulse by pulse over current limiting
More informationQUAD OPERATIONAL AMPLIFIERS FEATURES. SCHEMATIC DIAGRAM (One Section Only)
S The LM248/LM348 is a true quad LM741. It consists of four independent, high-gain, internally compensated, low-power operational amplifiers which have been designed to provide functional characteristics
More informationKA324 / KA324A / KA2902 Quad Operational Amplifier
KA324 / KA324A / KA2902 Quad Operational Amplifier Features Internally Frequency Compensated for Unity Gain Large DC oltage Gain: 100 db Wide Power Supply Range: KA324 / KA324A: 3 ~ 32 (or ±1.5 ~ 16 )
More informationKA378R05. Low Dropout Voltage Regulator. Features. Description. Internal Block Diagram.
KA78R5 Low Dropout Voltage Regulator www.fairchildsemi.com Features A / 5V Output low dropout voltage regulator TO Full-Mold package (PIN) Overcurrent protection, Thermal shutdown Overvoltage protection,
More informationDUAL OPERATIONAL AMPLIFIER
DUAL OPERATIONAL AMPLIFIER FEATURES n Wide Power Supply Range Single Supply: 3V ~ 32V Dual Supplies: ±.V ~ ±6V n Lower Input Offset : 2mV (Typ.) n Input CommonMode Range Include Ground n Differential Input
More informationKA239, LM339/A (KA339/A), LM2901 (KA2901), KA3302
QUAD DIFFERENTIAL COMPARATOR The LM/KA239 series consists of four independent voltage comparators designed to operate from single power supply over a wide voltage range. FEATURES Single or dual supply
More informationSII Semiconductor Corporation, Rev.3.1_01
www.sii-ic.com MINI ANALOG SERIES CMOS OPERATIONAL AMPLIFIER SII Semiconductor Corporation, 2009-2015 Rev.3.1_01 The mini-analog series is a group of ICs that incorporate a general purpose analog circuit
More informationLP2902/LP324 Micropower Quad Operational Amplifier
LP2902/LP324 Micropower Quad Operational Amplifier General Description The LP324 series consists of four independent, high gain internally compensated micropower operational amplifiers. These amplifiers
More informationTS358 Single Supply Dual Operational Amplifiers
SOP-8 DIP-8 Pin assignment: 1. Output A 8. Vcc 2. Input A (-) 7. Output B 3. Input A (+) 6. Input B (-) 4. Gnd 5. Input B (+) General Description Utilizing the circuit designs perfected for recently introduced
More informationTL082 Wide Bandwidth Dual JFET Input Operational Amplifier
TL082 Wide Bandwidth Dual JFET Input Operational Amplifier General Description These devices are low cost, high speed, dual JFET input operational amplifiers with an internally trimmed input offset voltage
More informationFAN7601. Green Current Mode PWM Controller. Description. Features. Typical Applications. Internal Block Diagram.
Green Current Mode PWM Controller www.fairchildsemi.com Features Green Current Mode PWM Control Low Operating Current: Max 4mA Burst Mode Operation Internal High Voltage Start-up Switch Under Voltage Lockout
More informationLF353 Wide Bandwidth Dual JFET Input Operational Amplifier
LF353 Wide Bandwidth Dual JFET Input Operational Amplifier General Description These devices are low cost, high speed, dual JFET input operational amplifiers with an internally trimmed input offset voltage
More informationTS3021H. Automotive rail-to-rail 1.8 V high-speed comparator. Related products. Applications. Description. Features SOT23-5
Automotive rail-to-rail 1.8 V high-speed comparator Datasheet - production data Related products TS3021 for standard temperature range (-40 C to 125 C) OUT IN+ 1 2 SOT23-5 + - Features AEC-Q100 and Q003
More informationELM824xA 3.0μA Very low power CMOS dual operational amplifier
ELM824xA 3.μA Very low power CMOS dual operational amplifier General description ELM824xA is a very low current consumption-typ.3.μa CMOS dual OP-AMP provided with a wide common mode input voltage range.
More informationLF442 Dual Low Power JFET Input Operational Amplifier
LF442 Dual Low Power JFET Input Operational Amplifier General Description The LF442 dual low power operational amplifiers provide many of the same AC characteristics as the industry standard LM1458 while
More informationKA7632/KA7633. Fixed Multi-output Regulator. Description. Features. Internal Block Diagram.
Fixed Multioutput Regulator www.fairchildsemi.com Features Output Currents up to.5a (output1 & ) Output Current up to 1A with External Transistor (output3) Fixed Precision Output 1 voltage 3.3V ± % Fixed
More informationLB4310. Dual Op Amp And Voltage Reference. General Description. Features. Applications. LB4310 Rev of /02/03.
General Description The LB4310 is a monolithic IC specifically designed to regulate the output current and voltage levels of switching battery chargers and power supplies The device contains two Op Amps
More informationDual high slew rate operational amplifier
Dual high slew rate operational amplifier BA6 / BA6F / BA6N The BA6, BA6F, and BA6N are dual operational amplifiers which achieve approximately twice the high output current of the BA, as well as featuring
More informationTS324 Low Power Quad Operational Amplifiers
DIP-14 General Description SOP-14 TS324 contains four independent high gain operational amplifiers with internal frequency compensation. The four opamps use a split power supply. The device has low power
More informationLMV321, LMV358, LMV324 General Purpose, Low Voltage, Rail-to-Rail Output Amplifiers
www.fairchildsemi.com LMV31, LMV358, LMV34 General Purpose, Low Voltage, RailtoRail Output Amplifiers Features at.7v 80µA supply current per channel 1.MHz gain bandwidth product Output voltage range: 0.01V
More informationLM158, LM258, LM358, LM158A, LM258A, LM358A
LM158, LM258, LM358, LM158A, LM258A, Low-power dual operational amplifiers Datasheet - production data Related products See LM158W for enhanced ESD ratings See LM2904 and LM2904W for automotive grade versions
More informationHIGH TEMPERATURE QUAD OPERATIONAL AMPLIFIER HT1104 APPLICATIONS FEATURES GENERAL DESCRIPTION PACKAGE PINOUT. HTMOS TM High Temperature Products
HTMOS TM High Temperature Products HIGH TEMPERATURE QUAD OPERATIONAL AMPLIFIER HT FEATURES Specified Over -55 to +5 C Single or Split Supply Operation Common-Mode Input Voltage Range Includes Negative
More informationTL082 Wide Bandwidth Dual JFET Input Operational Amplifier
TL082 Wide Bandwidth Dual JFET Input Operational Amplifier General Description These devices are low cost, high speed, dual JFET input operational amplifiers with an internally trimmed input offset voltage
More informationUNISONIC TECHNOLOGIES CO., LTD UM609A
UNISONIC TECHNOLOGIES CO., LTD DUAL OPERATIONAL AMPLIFIER AND CURRENT CONTROLLER DESCRIPTION The UTC is a monolithic IC that includes one independent op-amp and another op-amp for witch the non inverting
More informationLow power quad operational amplifiers
Low power quad operational amplifiers Features Wide gain bandwidth:.mhz typ. Input common-mode voltage range includes ground Large voltage gain:db typ. Very low supply current per amplifier:ua typ. Low
More informationLow-Power Quad Operational Amplifier FEATURES: DESCRIPTION: Memory. Logic Diagram. RAD-PAK technology-hardened against natural space radiation
Low-Power Quad Operational Amplifier FEATURES: RAD-PAK technology-hardened against natural space radiation Total dose hardness: - > 100 krad (Si), depending upon space mission Excellent Single Event Effects:
More informationLow Cost JFET Input Operational Amplifiers ADTL082/ADTL084
Low Cost JFET Input Operational Amplifiers ADTL/ADTL FEATURES TL/TL compatible Low input bias current: pa maximum Offset voltage 5.5 mv maximum (ADTLA/ADTLA) 9 mv maximum (ADTLJ/ADTLJ) ±5 V operation Low
More informationIP102. Dual OPAmp-Dual Comparator and Adj. Shunt Regulator DESCRIPTION FEATURES ORDERING INFORMATION BLOCK DIAGRAM
DESCRIPTION The IP102/A is a monolithic IC that includes two operational amplifiers, two comparators and an adjustable shunt regulator. This device is offering space and cost saving in many applications
More information15 MHz, Rail-to-Rail, Dual Operational Amplifier OP262-EP
5 MHz, Rail-to-Rail, Dual Operational Amplifier OP262-EP FEATURES Supports defense and aerospace applications (AQEC standard) Military temperature range ( 55 C to +25 C) Controlled manufacturing baseline
More informationDual Operational Amplifiers
FEATURES Wide range of supply voltages Low supply current drain independent of supply voltage Low input biasing current Low input offset voltage and offset current Input common-mode voltage range includes
More informationSP435W Dual OP AMP with Voltage Regulator
DESCRIPTION The SP435W is a monolithic IC specifically designed to control the output current and voltage levels of switch mode battery chargers and power supplies. The device contains two operational
More informationRT2904WH. RobuST low-power dual operational amplifier. Applications. Features. Description
RobuST low-power dual operational amplifier Datasheet - production data Features D SO8 (plastic micropackage) Pin connections (top view) Frequency compensation implemented internally Large DC voltage gain:
More informationLM321 Low Power Single Op Amp
Low Power Single Op Amp General Description The LM321 brings performance and economy to low power systems. With a high unity gain frequency and a guaranteed 0.4V/µs slew rate, the quiescent current is
More informationLM392 LM2924 Low Power Operational Amplifier Voltage Comparator
LM392 LM2924 Low Power Operational Amplifier Voltage Comparator General Description The LM392 series consists of 2 independent building block circuits One is a high gain internally frequency compensated
More informationLM1558/LM1458 Dual Operational Amplifier
LM1558/LM1458 Dual Operational Amplifier General Description The LM1558 and the LM1458 are general purpose dual operational amplifiers. The two amplifiers share a common bias network and power supply leads.
More informationLF412 Low Offset, Low Drift Dual JFET Input Operational Amplifier
LF412 Low Offset, Low Drift Dual JFET Input Operational Amplifier General Description These devices are low cost, high speed, JFET input operational amplifiers with very low input offset voltage and guaranteed
More informationTC75S55F, TC75S55FU, TC75S55FE
TOSHIBA CMOS Linear Integrated Circuit Silicon Monolithic TC7SF/FU/FE TC7SF, TC7SFU, TC7SFE Single Operational Amplifier The TC7SF/TC7SFU/TC7SFE is a CMOS singleoperation amplifier which incorporates a
More informationRC4207. Precision Monolithic Dual Operational Amplifier. Features. Description. Block Diagram. Pin Assignments.
www.fairchildsemi.com RC7 Precision Monolithic Dual Operational Amplifier Features Low Noise.5 mvp-p (. Hz to Hz) Ultra-low VO 75 mv Ultra-low VO drift. mv/ C Long term VO stability. mv/mo Low input bias
More informationAPX358/APX324 LOW VOLTAGE, RAIL-TO-RAIL INPUT AND OUTPUT DUAL/QUAD OPERATIONAL AMPLIFIERS
Features General Description (For V + =5V and V - =0V typical unless otherwise noted) Guaranteed 2.7V and 5V performance Crossover distortion eliminated Operating temperature range (-40 C to +85 C) Gain-bandwidth
More informationLM148, LM248, LM348 QUADRUPLE OPERATIONAL AMPLIFIERS
µa741 Operating Characteristics Low Supply Current Drain...0.6 ma Typ (per amplifier) Low Input Offset Voltage Low Input Offset Current Class AB Output Stage Input/Output Overload Protection Designed to
More informationIs Now Part of To learn more about ON Semiconductor, please visit our website at
Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC
More informationNE/SA/SE5532/5532A Internally-compensated dual low noise operational amplifier
INTEGRATED CIRCUITS Supersedes data of 1997 Sep 29 21 Aug 3 DESCRIPTION The 5532 is a dual high-performance low noise. Compared to most of the standard s, such as the 1458, it shows better noise performance,
More informationRV4145A. Low Power Ground Fault Interrupter. Features. Description. Block Diagram.
Low Power Ground Fault Interrupter www.fairchildsemi.com Features No potentiomenter required Direct interface to SCR Supply voltage derived from AC line 26V shunt Adjustable sensitivity Grounded neutral
More informationMicropower Precision CMOS Operational Amplifier AD8500
Micropower Precision CMOS Operational Amplifier AD85 FEATURES Supply current: μa maximum Offset voltage: mv maximum Single-supply or dual-supply operation Rail-to-rail input and output No phase reversal
More informationLM9044 Lambda Sensor Interface Amplifier
LM9044 Lambda Sensor Interface Amplifier General Description The LM9044 is a precision differential amplifier specifically designed for operation in the automotive environment. Gain accuracy is guaranteed
More informationFAN8728. Spindle + 4-CH Input PWM Motor Drive IC. Features. Description. Typical Applications. Ordering Information.
Spindle 4-CH Input PWM Motor Drive IC www.fairchildsemi.com Features!!"! #$ "%"" &'( $)* $, $# " ",-,. Description /012*1 " "3 % # " 4 %" ", " " % &5/!&5/!0/.6/60 "7"- 48-QFPH-1414 Typical Applications
More informationML4818 Phase Modulation/Soft Switching Controller
Phase Modulation/Soft Switching Controller www.fairchildsemi.com Features Full bridge phase modulation zero voltage switching circuit with programmable ZV transition times Constant frequency operation
More informationTS3022. Rail-to-rail 1.8 V high-speed dual comparator. Applications. Description. Features
TS22 Rail-to-rail 1.8 V high-speed dual comparator Datasheet - production data Applications Telecom Instrumentation Signal conditioning High-speed sampling systems Portable communication systems Automotive
More informationRC A Adjustable/Fixed Low Dropout Linear Regulator. Description. Features. Applications. Typical Applications.
www.fairchildsemi.com A Adjustable/Fixed Low Dropout Linear Regulator Features Low dropout voltage Load regulation:.5% typical Trimmed current limit On-chip thermal limiting Standard SOT-223, TO-263, and
More informationNE/SA/SE532 LM258/358/A/2904 Low power dual operational amplifiers
INTEGRATED CIRCUITS NE/SA/SE53 Supersedes data of Jan Jul 1 DESCRIPTION The 53/358/LM94 consists of two independent, high gain, internally frequency-compensated operational amplifiers internally frequency-compensated
More information