ELM824xA 3.0μA Very low power CMOS dual operational amplifier

Size: px
Start display at page:

Download "ELM824xA 3.0μA Very low power CMOS dual operational amplifier"

Transcription

1 ELM824xA 3.μA Very low power CMOS dual operational amplifier General description ELM824xA is a very low current consumption-typ.3.μa CMOS dual OP-AMP provided with a wide common mode input voltage range. It has a quasi rail-to-rail input stage and a push-pull rail-to-rail output stage. ELM824xA can operate down to 1.2V. ELM824xA is suitable for portable devices which require low power and a single voltage source. Features Application Operation from a single power source Battery-operated portable devices Low voltage operation : 1.2V Vdd 6.V Micropower signal process Low current consumption : Typ.3.μA Low voltage analog circuit N-channel depletion differential input : No gm dependence on input operating points Common-mode input voltage range : Quasi rail-to-rail input Vss to Vdd-.3V(Vdd=V) Vss to Vdd-.1V(Vdd=3.V) Output stage : Push-pull rail-to-rail output Unity gain bandwidth : Typ.15kHz(Vdd V) Package : SOT-28, SOP-8, TSSOP-8 Maximum absolute ratings Parameter Symbol Limit Unit Power supply voltage Vdd 7. V Input voltage Vin Vss-.3 to Vdd+.3 V Output voltage Vout Vss-.3 to Vdd+.3 V Output short circuit Continuous Sec. Power dissipation Pd 3 mw Operating temperature Top -4 to +85 C Storage temperature Tstg -55 to +125 C Selection guide ELM824xA-x Symbol a Package B: SOT-28 D: SOP-8 E: TSSOP-8 b Product version A c Taping direction S: Refer to PKG file N: Refer to PKG file ELM824 x A - x a b c 1-1

2 ELM824xA 3.μA Very low power CMOS dual operational amplifier Pin configuration SOT-28(TOP VIEW) SOP-8(TOP VIEW) TSSOP-8(TOP VIEW) Pin No. Pin name Pin No. Pin name 1 OUTA 5 IN+B 2 IN-A 6 IN-B 3 IN+A 7 OUTB 4 VSS 8 VDD Standard circuit Marking SOT-28 SOP-8 TSSOP-8 Symbol Mark Content a to 9 Last numeral of A.D. b A to M (excepted I.) Assembly month c to 9 d e to 9 and A to Z (I, O, X excepted.) Lot No. 1-2

3 ELM824xA 3.μA Very low power CMOS dual operational amplifier Electrical characteristics Vss=V, Top=-4~+85 C Parameter Symbol Condition Min. Typ. Max. Unit Operating voltage Vdd V Vdd=V Vss=V, Top=25 C Parameter Symbol Condition Min. Typ. Max. Unit Input offset voltage Vio Vcm=Vdd/2, Unity gain follower ±6 mv Input bias current Iib 1. na Common-mode input voltage range Vcmr For CMRR 45dB. 1.2 V Maximum output voltage swing Voutsh Vid=1mV, RL=1kΩ to Vss 1.4 V Minimum output voltage swing Voutsl Vid=1mV, RL=1kΩ to Vdd.1 V Source current Isource Vout=1.2V, Vid=1mV.4 1. ma Sink current Isink Vout=.3V, Vid=1mV ma Large-signal voltage gain Avd RL=1kΩ to Vss, Vcm=.75V 95 db Common-mode rejection ratio CMRR RL=1kΩ to Vss, Vcm=.75V 85 db Supply voltage rejection ratio PSRR RL=1kΩ to Vss, Vcm=.75V 95 db Current consumption Iss Vcm=Vdd/2, Unity gain follower μa Short current Ishortp Vout to Vss shrot, Vid=1mV 1.4 ma Ishortn Vout to Vdd shrot, Vid=1mV 4. ma Unity gain bandwidth GBW 15 khz Slew rate SR RL=1kΩ, CL=2pF mv/μs Vdd=3.V Vss=V, Top=25 C Parameter Symbol Condition Min. Typ. Max. Unit Input offset voltage Vio Vcm=Vdd/2, Unity gain follower ±6 mv Input bias current Iib 1. na Common-mode input voltage range Vcmr For CMRR 45dB. 2.9 V Maximum output voltage swing Voutsh Vid=1mV, RL=1kΩ to Vss 2.9 V Minimum output voltage swing Voutsl Vid=1mV, RL=1kΩ to Vdd.1 V Source current Isource Vout=2.7V, Vid=1mV 4. ma Sink current Isink Vout=.3V, Vid=1mV ma Large-signal voltage gain Avd RL=1kΩ to Vss, Vcm=V 1 db Common-mode rejection ratio CMRR RL=1kΩ to Vss, Vcm=V 9 db Supply voltage rejection ratio PSRR RL=1kΩ to Vss, Vcm=V 1 db Current consumption Iss Vcm=Vdd/2, Unity gain follower μa Short current Ishortp Vout to Vss shrot, Vid=1mV 14 ma Ishortn Vout to Vdd shrot, Vid=1mV 25 ma Unity gain bandwidth GBW 15 khz Slew rate SR RL=1kΩ, CL=2pF mv/μs 1-3

4 Note ELM824xA 3.μA Very low power CMOS dual operational amplifier 1) Common mode input voltage range ELM824xA common mode input voltage range is fixed under the condition of CMRR 45dB; ELM824xA is able to accept the input above its specification if the degradation of CMRR is not considered. Even if the input voltage exceeds either positive or negative power voltage, troubles such as reverse of output will not occur. As maximum absolute rating, the input voltage is possible within (Vss-.3)V to (Vdd+.3)V. 2) Operation from single power source ELM824xA is designed to be most suitable for single power source; therefore, ELM824xA is able to share power supply with logic circuit one. Meanwhile, ELM824xA can also operate from double power sources. To protect power supplies of ELM824xA and logic circuit from noise, please separate wire from power supply and use decoupling (bypass) capacitor. Using the capacitor can improve PSRR characteristics, especially on 1kHz to 1kHz or more. 3) Feedback When OP-AMP circuit is used with feedback resistor, oscillation may happen in the circuit with loop-gain like unity gain follower. a) When large feedback resistance is used, the phase margin is decreased by its combination with the parasitic capacitance of the input part of OP-AMP. In this situation, please connect small capacitor in parallel with feedback resistor as shown in fig-1. b) For capacitive load, external resistor in series connection will be effective as shown in fig-2. (RL=3 to 5Ω) c) Being used as an unity gain follow, ELM824xA is able to drive capacitive load of 1pF directly without oscillation. a) fig-1 b) fig-2 4) Unused Amplifier Two amplifiers will consume power even if only one amplifier is used. In order to minimize power consumption by the unused amplifier, ELM recommends to connect this amplifier as voltage follower circuit and the input terminal (IN+) to Vdd. 1-4

5 ELM824xA 3.μA Very low power CMOS dual operational amplifier Typical characteristics 6. Iss-Vdd Unity Gain, Vcm=Vdd/2, No load 6. Iss-Top Unity Gain, Vcm=Vdd/2, No load Iss ( A) Top=-4 Iss ( A) Vdd=3.V Vdd=6.V Vdd=V Vdd=1.2V Vdd (V) Top ( ) Iss-Input Voltage Unity Gain, Vdd=3.V, No load Offset Voltage distribution Unity Gain, Vdd=3.V, Vcm=V, No load, Top=25 ss ( A) Top=-4 Percent (%) Input Voltage (V) Offset Voltage (mv) 1 Avd-Frequency Vcm=Vdd/2, 1k load, Top=25 1 Avd-Frequency Vdd=3.V, Vcm=V, 1k load 8 Vdd=6.V 8 Avd (db) Vdd=3.V Vdd=V Vdd=1.2V Avd (db) Top=

6 ELM824xA 3.μA Very low power CMOS dual operational amplifier CMRR-Frequency Unity Gain, Vcm=Vdd/2, 1k load, Top=25 Vdd=6.V Vdd=3.V Vdd=V Vdd=1.2V CMRR-Frequency 12 Unity Gain, Vdd=3.V, Vcm=V, 1k load Top= CMRR-Vcm [Vdd=1.2V] Frequency=1Hz, Unity Gain, 1k load 12 CMRR-Vcm [Vdd=V] Frequency=1Hz, Unity Gain, 1k load Top= Top= Vcm (V) Vcm (V) 12 CMRR-Vcm [Vdd=3.V] Frequency=1Hz, Unity Gain, 1k load 12 CMRR-Vcm [Vdd=6.V] Frequency=1Hz, Unity Gain, 1k load Top= Top= Vcm (V) Vcm (V) 1-6

7 ELM824xA 3.μA Very low power CMOS dual operational amplifier 12 1 PSRR-Frequency Unity Gain, Vcm=Vdd/2, Vdd=3.V 1k load, Top= PSRR-Frequency Unity Gain, Vdd=3.V, Vcm=V, 1k load PSRR (db) Vdd=V Vdd=1.2V Vdd=6.V PSRR (db) Top= SR-Vdd Unity Gain, 1k load Falling edge (Top=+85 ) Rising edge (Top=+85 ) 3 25 SR-Top Vdd=3.V, Unity Gain, 1k load SR (mv/ s) 2 15 Falling edge (Top=+25 ) 1 Rising edge (Top=+25 ) 5 Falling edge (Top=-4 ) Rising edge (Top=-4 ) Vdd (V) SR (mv/ s) Falling edge Rising edge Top ( ) Isource (ma) Isource-Vout [Vdd=1.2V] Vid=1mV Top=-4 Isource (ma) Isource-Vout [Vdd=V] Vid=1mV Top=

8 ELM824xA 3.μA Very low power CMOS dual operational amplifier Isource (ma) Isource-Vout [Vdd=3.V] Top=-4 Vid=1mV Isource (ma) Isource-Vout [Vdd=6.V] Top=-4 Vid=1mV Isink-Vout [Vdd=1.2V] Vid=1mV Top= Isink-Vout [Vdd=V] Top=-4 Vid=1mV Isink (ma) 1. Isink (ma) Isink-Vout [Vdd=3.V] Vid=1mV 12 Isink-Vout [Vdd=6.V] Vid=1mV Isink (ma) Top=-4 Isink (ma) Top=

9 ELM824xA 3.μA Very low power CMOS dual operational amplifier Short Circuit Current (ma) Short Circuit Current-Vdd Vout to Vss short, Vid=1mV Top= Vdd (V) Short Circuit Current (ma) Short Circuit Current-Vdd Vout to Vdd short, Vid=1mV Top= Vdd (V) Maximum Maximum Vout-RL [Vdd=1.2V] RL is connected between Vout and Vss. Vid=1mV Top=-4 Maximum Maximum Vout-RL [Vdd=V] RL is connected between Vout and Vss. Vid=1mV Top= Maximum Maximum Vout-RL [Vdd=3.V] RL is connected between Vout and Vss. Vid=1mV Top=-4 Maximum Maximum Vout-RL [Vdd=6.V] RL is connected between Vout and Vss. Vid=1mV Top=

10 ELM824xA 3.μA Very low power CMOS dual operational amplifier Minimum Minimum Vout-RL [Vdd=1.2V] RL is connected between Vdd and Vout. Vid=1mV.2 Top= Minimum Minimum Vout-RL [Vdd=V] RL is connected between Vdd and Vout. Vid=1mV Top= Minimum Vout-RL [Vdd=3.V] RL is connected between Vdd and Vout. Vid=1mV Minimum Vout-RL [Vdd=6.V] RL is connected between Vdd and Vout. Vid=1mV Minimum Minimum Top=-4 1. Top= Pulse Response [Vdd=V] Unity Gain, 1k load, Top=25 3. Pulse Response [Vdd=3.V] Unity Gain, 1k load, Top=25 Vin (V) 1..5 Vin Vin (V) Vin 3.. Vout Vout Time ( s) Time ( s) 1-1

HT9291/HT9292/HT9294 TinyPower TM Operation Amplifier

HT9291/HT9292/HT9294 TinyPower TM Operation Amplifier TinyPower TM Operation Amplifier Features Wide operating voltage: 1.4V to 5.5V Low quiescent current: typical 0.6µA/amplifier Rail-to-Rail output Gain bandwidth: 11kHz typical Unity gain stable Available

More information

HT9231/HT9232/HT9234 Operation Amplifier

HT9231/HT9232/HT9234 Operation Amplifier Operation Amplifier Features Operating Voltage: 2.0V to 5.5V Supply Current: 220μA/amplifier typical Rail-to-Rail Output Gain Bandwidth: 2.3MHz typical Unity Gain Stable Available in Single, Dual and Quad

More information

EC kHz, 7μA, CMOS, Rail-to-Rail Operational Amplifier. General Description. Features. Applications. Pin Assignments

EC kHz, 7μA, CMOS, Rail-to-Rail Operational Amplifier. General Description. Features. Applications. Pin Assignments General Description Features The is a single supply, low power CMOS operational amplifier; these amplifiers offer bandwidth of 250kHz, rail-to-rail inputs and outputs, and single-supply operation from

More information

350MHZ CMOS Rail-to-Rail Output Opamps

350MHZ CMOS Rail-to-Rail Output Opamps Features Single-Supply Operation from +2.5V ~ +5.5V Rail-to-Rail Output -3dB Bandwidth(G=+1): 350MHz (Typ.) Low Input Bias Current: 1pA (Typ.) Quiescent Current: 4.2mA/Amplifier (Typ.) Operating Temperature:

More information

UTC UNISONIC TECHNOLOGIES CO., LTD. 1 LINEAR INTEGRATED CIRCUIT QUAD OPERATIONAL AMPLIFIERS

UTC UNISONIC TECHNOLOGIES CO., LTD. 1 LINEAR INTEGRATED CIRCUIT QUAD OPERATIONAL AMPLIFIERS UTC LM QUAD OPERATIONAL AMPLIFIERS DESCRIPTION The UTC LM consists of four independent, high gain internally frequency compensated operational amplifiers which are designed specifically to operated from

More information

PART. Maxim Integrated Products 1

PART. Maxim Integrated Products 1 - + 9-; Rev ; / Low-Cost, High-Slew-Rate, Rail-to-Rail I/O Op Amps in SC7 General Description The MAX9/MAX9/MAX9 single/dual/quad, low-cost CMOS op amps feature Rail-to-Rail input and output capability

More information

Single/Dual/Quad, +1.8V/750nA, SC70, Rail-to-Rail Op Amps

Single/Dual/Quad, +1.8V/750nA, SC70, Rail-to-Rail Op Amps 9-; Rev 4; 7/ Single/Dual/Quad, +.8V/75nA, SC7, General Description The MAX4464/MAX447/MAX447/MAX447/MAX4474 family of micropower op amps operate from a single +.8V to +5.5V supply and draw only 75nA of

More information

MIC915. Features. General Description. Applications. Ordering Information. Pin Configuration. Pin Description. Dual 135MHz Low-Power Op Amp

MIC915. Features. General Description. Applications. Ordering Information. Pin Configuration. Pin Description. Dual 135MHz Low-Power Op Amp MIC915 Dual 135MHz Low-Power Op Amp General Description The MIC915 is a high-speed, unity-gain stable operational amplifier. It provides a gain-bandwidth product of 135MHz with a very low, 2.4mA supply

More information

KA224/KA224A, KA324/KA324A, KA2902

KA224/KA224A, KA324/KA324A, KA2902 KA224/KA224A, KA324/KA324A, KA2902 Quad Operational Amplifier www.fairchildsemi.com Features Internally Frequency Compensated for Unity Gain Large DC Voltage Gain: 100dB Wide Power Supply Range: KA224

More information

EC MHz, CMOS, Rail-to-Rail Output Operational Amplifier. General Description. Features. Applications. Pin Configurations(Top View)

EC MHz, CMOS, Rail-to-Rail Output Operational Amplifier. General Description. Features. Applications. Pin Configurations(Top View) General Description The is wideband, low-noise, low-distortion operational amplifier, that offer rail-to-rail output and single-supply operation down to 2.2V. They draw 5.6mA of quiescent supply current,

More information

GT MHz, Low Power, CMOS, EMI Hardened, Rail-to-Rail Quad Operational Amplifier. 1. Features. 2. General Description. 3. Applications A0 1/16

GT MHz, Low Power, CMOS, EMI Hardened, Rail-to-Rail Quad Operational Amplifier. 1. Features. 2. General Description. 3. Applications A0 1/16 MHz, Low Power, CMOS, EMI Hardened, Rail-to-Rail Quad Operational Amplifier Advanced. Features Single-Supply Operation from +. ~ +5.5 Low Offset oltage: 5m (Max.) Rail-to-Rail Input / Output Quiescent

More information

SGM8521/2/4 150kHz, 5.5μA, Rail-to-Rail I/O, CMOS Operational Amplifiers

SGM8521/2/4 150kHz, 5.5μA, Rail-to-Rail I/O, CMOS Operational Amplifiers //4 0kHz,.μA, Rail-to-Rail I/O, GENERAL DESCRIPTION The (single), SGM8 (dual) and SGM84 (quad) are low cost, rail-to-rail input and output voltage feedback amplifiers. They have a wide input common mode

More information

MIC7122. General Description. Features. Applications. Ordering Information. Pin Configuration. Pin Description. Rail-to-Rail Dual Op Amp

MIC7122. General Description. Features. Applications. Ordering Information. Pin Configuration. Pin Description. Rail-to-Rail Dual Op Amp MIC722 Rail-to-Rail Dual Op Amp General Description The MIC722 is a dual high-performance CMOS operational amplifier featuring rail-to-rail inputs and outputs. The input common-mode range extends beyond

More information

Quad Ground Sense Operational Amplifier. The CO324 is monolithic IC with four built-in operational amplifiers featuring internal phase compensation.

Quad Ground Sense Operational Amplifier. The CO324 is monolithic IC with four built-in operational amplifiers featuring internal phase compensation. The CO4 is monolithic IC with four built-in operational amplifiers featuring internal phase compensation. Either a dual or single power supply can be driven, and these products can be driven by a digital

More information

SII Semiconductor Corporation, Rev.3.1_01

SII Semiconductor Corporation, Rev.3.1_01 www.sii-ic.com MINI ANALOG SERIES CMOS OPERATIONAL AMPLIFIER SII Semiconductor Corporation, 2009-2015 Rev.3.1_01 The mini-analog series is a group of ICs that incorporate a general purpose analog circuit

More information

SGM8621/2/3/4 3MHz, Rail-to-Rail I/O CMOS Operational Amplifiers

SGM8621/2/3/4 3MHz, Rail-to-Rail I/O CMOS Operational Amplifiers SGM8621/2/3/4 3MHz, Rail-to-Rail I/O PRODUCT DESCRIPTION The SGM8621 (single), SGM8622 (dual), SGM8623 (single with shutdown) and SGM8624 (quad) are low noise, low voltage, and low power operational amplifiers,

More information

I/O Op Amps with Shutdown

I/O Op Amps with Shutdown MHz, μa, Rail-to-Rail General Description The single MAX994/MAX995 and dual MAX996/ MAX997 operational amplifiers feature maximized ratio of gain bandwidth to supply current and are ideal for battery-powered

More information

Micropower Precision CMOS Operational Amplifier AD8500

Micropower Precision CMOS Operational Amplifier AD8500 Micropower Precision CMOS Operational Amplifier AD85 FEATURES Supply current: μa maximum Offset voltage: mv maximum Single-supply or dual-supply operation Rail-to-rail input and output No phase reversal

More information

Dual operational amplifier

Dual operational amplifier Dual operational amplifier The BA8, BA8F, and BA8N are monolithic ICs with two operational amplifiers featuring low power consumption and internal phase compensation mounted on a single silicon chip. These

More information

Quad ground sense operational amplifier

Quad ground sense operational amplifier Quad ground sense operational amplifier BAA / BAAF / BAAFV The BAA, BAAF, and BAAFV are monolithic ICs with four built-in operational amplifiers featuring internal phase compensation. Either a dual or

More information

SGM8631/2/3 6MHz, Rail-to-Rail I/O CMOS Operational Amplifiers

SGM8631/2/3 6MHz, Rail-to-Rail I/O CMOS Operational Amplifiers /2/3 6MHz, Rail-to-Rail I/O PRODUCT DESCRIPTION The (single), SGM8632 (dual) and SGM8633 (single with shutdown) are low noise, low voltage, and low power operational amplifiers that can be designed into

More information

Precision, Low-Power and Low-Noise Op Amp with RRIO

Precision, Low-Power and Low-Noise Op Amp with RRIO MAX41 General Description The MAX41 is a low-power, zero-drift operational amplifier available in a space-saving, 6-bump, wafer-level package (WLP). Designed for use in portable consumer, medical, and

More information

EC5462A High Slew Rate Rail-to-Rail Dual Operational Amplifiers

EC5462A High Slew Rate Rail-to-Rail Dual Operational Amplifiers Introduction (General Description) The EC5462A is a rail-to-rail dual channels operational amplifier with wide supply range from 4.5V to 18V. It provides 0.5V beyond the supply rails of common mode input

More information

LM2904,LM358/LM358A,LM258/ LM258A

LM2904,LM358/LM358A,LM258/ LM258A LM2904,LM358/LM358A,LM258/ LM258A Dual Operational Amplifier www.fairchildsemi.com Features Internally Frequency Compensated for Unity Gain Large DC Voltage Gain: 100dB Wide Power Supply Range: LM258/LM258A,

More information

LM324/LM324A, LM2902/LM2902A

LM324/LM324A, LM2902/LM2902A www.fairchildsemi.com LM324/LM324A, LM2902/LM2902A Quad Operational Amplifier Features Internally Frequency Compensated for Unity Gain Large DC Voltage Gain: 100dB Wide Power Supply Range: LM324/LM324A

More information

1.0V Micropower, SOT23, Operational Amplifier

1.0V Micropower, SOT23, Operational Amplifier 19-3; Rev ; 1/ 1.V Micropower, SOT3, Operational Amplifier General Description The micropower, operational amplifier is optimized for ultra-low supply voltage operation. The amplifier consumes only 9µA

More information

Nanopower Op Amp in Ultra-Tiny WLP and SOT23 Packages

Nanopower Op Amp in Ultra-Tiny WLP and SOT23 Packages EVALUATION KIT AVAILABLE MAX47 General Description The MAX47 is a single operational amplifier that provides a maximized ratio of gain bandwidth (GBW) to supply current and is ideal for battery-powered

More information

UNISONIC TECHNOLOGIES CO., LTD

UNISONIC TECHNOLOGIES CO., LTD UNISONIC TECHNOLOGIES CO., LTD GENERAL PURPOSE, LOW VOLTAGE, RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIERS DESCRIPTION The UTC LV358 is a dual op amp with low supply current and low voltage (2.7-5.5V). It

More information

HT9251/HT9252/HT9254 Low Voltage Operational Amplifiers

HT9251/HT9252/HT9254 Low Voltage Operational Amplifiers Low Voltage Operational Amplifiers Features Supply voltage range from 1.8V to 5.5V Supply Current: 50μA/amplifier - typical Rail-to-Rail Input/Output Gain Bandwidth: 550kHz - typical Available in Single

More information

SGM321/SGM358/SGM324 1MHz, 60μA, Rail-to-Rail I/O CMOS Operational Amplifiers

SGM321/SGM358/SGM324 1MHz, 60μA, Rail-to-Rail I/O CMOS Operational Amplifiers /SGM358/SGM324 1MHz, 60μA, Rail-to-Rail I/O CMOS Operational Amplifiers GENERAL DESCRIPTION The (single), SGM358 (dual) and SGM324 (quad) are low cost, rail-to-rail input and output voltage feedback amplifiers.

More information

SGM8631/2/3/4 470μA, 6MHz, Rail-to-Rail I/O CMOS Operational Amplifiers

SGM8631/2/3/4 470μA, 6MHz, Rail-to-Rail I/O CMOS Operational Amplifiers PRODUCT DESCRIPTION The SGM863 (single), SGM863 (dual), SGM8633 (single with shutdown) and SGM8634 (quad) are low noise, low voltage, and low power operational amplifiers, that can be designed into a wide

More information

190μA, 3MHz, Rail-to-Rail I/O CMOS Operational Amplifiers VREF. DIO2026QN20 D2026 RoHS/Green -40 to +125 C QFN4*4-20 Tape & Reel, 5000

190μA, 3MHz, Rail-to-Rail I/O CMOS Operational Amplifiers VREF. DIO2026QN20 D2026 RoHS/Green -40 to +125 C QFN4*4-20 Tape & Reel, 5000 Rev 0.1 DIO2026 190μA, 3MHz, Rail-to-Rail I/O CMOS Operational Amplifiers Features Supply Voltage Range: 2.5V to 5.5V Supply Current: Typical 190μA per channel Rail-to-Rail Input and Output ±1mV Typical

More information

KA741/KA741E. Single Operational Amplifier. Features. Description. Internal Block Diagram.

KA741/KA741E. Single Operational Amplifier. Features. Description. Internal Block Diagram. Single Operational Amplifier www.fairchildsemi.com Features Short circuit protection Excellent temperature stability Internal frequency compensation High Input voltage range Null of offset Description

More information

S-19610A MINI ANALOG SERIES FOR AUTOMOTIVE 125 C OPERATION CMOS OPERATIONAL AMPLIFIER. Features. Applications. Package.

S-19610A MINI ANALOG SERIES FOR AUTOMOTIVE 125 C OPERATION CMOS OPERATIONAL AMPLIFIER. Features. Applications. Package. www.sii-ic.com MINI ANALOG SERIES FOR AUTOMOTIVE 15 C OPERATION CMOS OPERATIONAL AMPLIFIER SII Semiconductor Corporation, 14 The mini-analog series is a group of ICs that incorporate a general purpose

More information

UNISONIC TECHNOLOGIES CO., LTD

UNISONIC TECHNOLOGIES CO., LTD UNISONIC TECHNOLOGIES CO., LTD SINGLE GENERAL PURPOSE, LOW VOLTAGE, RAIL-TO-RAIL OUTPUT OPERATIONAL AMPLIFIER DESCRIPTION The UTC LV321 is a single op amp with low supply current. It brings good performance

More information

SP435W Dual OP AMP with Voltage Regulator

SP435W Dual OP AMP with Voltage Regulator DESCRIPTION The SP435W is a monolithic IC specifically designed to control the output current and voltage levels of switch mode battery chargers and power supplies. The device contains two operational

More information

Rail-to-rail input/output, 29 µa, 420 khz CMOS operational amplifiers. Description. TSV62x TSV622 TSV623 TSV624 TSV625

Rail-to-rail input/output, 29 µa, 420 khz CMOS operational amplifiers. Description. TSV62x TSV622 TSV623 TSV624 TSV625 Rail-to-rail input/output, 29 µa, 420 khz CMOS operational amplifiers Applications Datasheet - production data TSSOP14 Features SO8 MiniSO8/MiniSO10 Rail-to-rail input and output Low power consumption:

More information

Features. Applications

Features. Applications 105MHz Low-Power SOT23-5 Op Amp General Description The is a high-speed operational amplifier which is unity gain stable regardless of resistive and capacitive load. It provides a gain-bandwidth product

More information

Dual operational amplifier

Dual operational amplifier DESCRIPTION The 77 is a pair of high-performance monolithic operational amplifiers constructed on a single silicon chip. High common-mode voltage range and absence of latch-up make the 77 ideal for use

More information

SGM MHz, 48μA, Rail-to-Rail I/O CMOS Operational Amplifier

SGM MHz, 48μA, Rail-to-Rail I/O CMOS Operational Amplifier PRODUCT DESCRIPTION The is a low cost, single rail-to-rail input and output voltage feedback amplifier. It has a wide input common mode voltage range and output voltage swing, and takes the minimum operating

More information

Not Recommended for New Designs

Not Recommended for New Designs Not Recommended for New Designs This product was manufactured for Maxim by an outside wafer foundry using a process that is no longer available. It is not recommended for new designs. The data sheet remains

More information

HT9274 Quad Micropower Op Amp

HT9274 Quad Micropower Op Amp Quad Micropower Op Amp Features Quad micro power op amp Wide range of supply voltage: 1.6V~5.5V High input impedance Single supply operation Low current consumption: < 5A per amp Rail to rail output Provides

More information

Low Power LM321N5. Low Power Single Operational Amplifier. General Description. Features. Applications

Low Power LM321N5. Low Power Single Operational Amplifier. General Description. Features. Applications Low Power Single Operational Amplifier Low Power Single Operational Amplifier General Description The is a high gain and internally frequency compensated operational amplifier specifically designed to

More information

ULTRA HIGH SPEED SINGLE OPERATIONAL AMPLIFIER

ULTRA HIGH SPEED SINGLE OPERATIONAL AMPLIFIER ULTRA HIGH SPEED SINGLE OPERATIONAL AMPLIFIER GENERAL DESCRIPTION The NJM711 is an ultra high speed single operational amplifier. It can swings 6V/µs high slew rate and 1GHz gain band width product(1mhz

More information

TSV611, TSV611A, TSV612, TSV612A

TSV611, TSV611A, TSV612, TSV612A TSV611, TSV611A, TSV612, TSV612A Rail-to-rail input/output 10 µa, 120 khz CMOS operational amplifiers Applications Datasheet - production data Out1 1 In1-2 In1+ 3 TSV611ILT - TSV611ICT In+ 1 5 V CC+ +

More information

ABLIC Inc., 2018 Rev.1.0_00

ABLIC Inc., 2018 Rev.1.0_00 S-1963A www.ablic.com AUTOMOTIVE, 15 C OPERATION, LOW INPUT OFFSET VOLTAGE CMOS OPERATIONAL AMPLIFIER ABLIC Inc., 18 Rev.1._ This IC incorporates a general purpose analog circuit in a small package. This

More information

ABLIC Inc., 2018 Rev.1.0_00

ABLIC Inc., 2018 Rev.1.0_00 www.ablic.com 15 C OPERATION, LOW INPUT OFFSET VOLTAGE CMOS OPERATIONAL AMPLIFIER ABLIC Inc., 18 This IC incorporates a general purpose analog circuit in a small package. This is a zero-drift operational

More information

MCP6031/2/3/ µa, High Precision Op Amps. Features. Description. Applications. Design Aids. Package Types. Typical Application

MCP6031/2/3/ µa, High Precision Op Amps. Features. Description. Applications. Design Aids. Package Types. Typical Application 0.9 µa, High Precision Op Amps Features Rail-to-Rail Input and Output Low Offset Voltage: ±150 µv (maximum) Ultra Low Quiescent Current: 0.9 µa Wide Power Supply Voltage: 1.8V to 5.5V Gain Bandwidth Product:

More information

1.8 V Low Power CMOS Rail-to-Rail Input/Output Operational Amplifier AD8515

1.8 V Low Power CMOS Rail-to-Rail Input/Output Operational Amplifier AD8515 Data Sheet FEATURES Single-supply operation: 1.8 V to 5 V Offset voltage: 6 mv maximum Space-saving SOT-23 and SC7 packages Slew rate: 2.7 V/μs Bandwidth: 5 MHz Rail-to-rail input and output swing Low

More information

LP2902/LP324 Micropower Quad Operational Amplifier

LP2902/LP324 Micropower Quad Operational Amplifier LP2902/LP324 Micropower Quad Operational Amplifier General Description The LP324 series consists of four independent, high gain internally compensated micropower operational amplifiers. These amplifiers

More information

nanopower Op Amp in a Tiny 6-Bump WLP

nanopower Op Amp in a Tiny 6-Bump WLP EVALUATION KIT AVAILABLE MAX4464 General Description The MAX4464 is an ultra-small (6-bump WLP) op amp that draws only 75nA of supply current. It operates from a single +.8V to +5.5V supply and features

More information

LMV331TP / LMV393TP. General Purpose, 1.8V, RRI, Open-Drain Output Comparators. Features. Description. Applications. Pin Configuration (Top View)

LMV331TP / LMV393TP. General Purpose, 1.8V, RRI, Open-Drain Output Comparators. Features. Description. Applications. Pin Configuration (Top View) Features 3PEAK LMV331TP / LMV393TP Description Down to 1.8V Supply Voltage: 1.8V to 5.5V Low Supply Current: 40 μa per Channel High-to-Low Propagation Delay: 10 ns Internal Hysteresis Ensures Clean Switching

More information

Features. Ordering Information. Part Number Standard Marking Pb-Free Marking

Features. Ordering Information. Part Number Standard Marking Pb-Free Marking MIC9 MIC9 8MHz Low-Power SC-7 Op Amp General Description The MIC9 is a high-speed operational amplifier with a gain-bandwidth product of 8MHz. The part is unity gain stable. It has a very low µa supply

More information

Features. Applications SOT-23-5 (M5)

Features. Applications SOT-23-5 (M5) 1.8V to 11V, 15µA, 25kHz GBW, Rail-to-Rail Input and Output Operational Amplifier General Description The is a low-power operational amplifier with railto-rail inputs and outputs. The device operates from

More information

15 MHz, Rail-to-Rail, Dual Operational Amplifier OP262-EP

15 MHz, Rail-to-Rail, Dual Operational Amplifier OP262-EP 5 MHz, Rail-to-Rail, Dual Operational Amplifier OP262-EP FEATURES Supports defense and aerospace applications (AQEC standard) Military temperature range ( 55 C to +25 C) Controlled manufacturing baseline

More information

TSB611. Low-power, rail-to-rail output, 36 V operational amplifier. Applications

TSB611. Low-power, rail-to-rail output, 36 V operational amplifier. Applications Low-power, rail-to-rail output, 36 V operational amplifier Datasheet - production data Applications Industrial Power supplies Automotive OUT IN+ 1 2 SOT23-5 + - VCC+ VCC- IN- Features Low offset voltage:

More information

SGM721 SGM722 SGM723 SGM µA, 10MHz, Rail-to-Rail I/O CMOS Operational Amplifier FEATURES PRODUCT DESCRIPTION. PIN CONFIGURATIONS (Top View)

SGM721 SGM722 SGM723 SGM µA, 10MHz, Rail-to-Rail I/O CMOS Operational Amplifier FEATURES PRODUCT DESCRIPTION. PIN CONFIGURATIONS (Top View) SGM7 SGM7 SGM73 SGM74 PRODUCT DESCRIPTION The SGM7 (single), SGM7 (dual), SGM73 (single with shutdown) and SGM74 (quad) are low noise, low voltage, and low power operational amplifiers, that can be designed

More information

V OUT. +Denotes lead(pb)-free/rohs-compliant package. PART

V OUT. +Denotes lead(pb)-free/rohs-compliant package. PART 9-346; Rev 2; / 2kHz, 4µA, Rail-to-Rail General Description The single MAX99/MAX99 and dual MAX992/ MAX993 operational amplifiers (op amps) feature a maximized ratio of gain bandwidth (GBW) to supply current

More information

SGM ns, Low-Power, 3V/5V, Rail-to-Rail Input Single-Supply Comparator

SGM ns, Low-Power, 3V/5V, Rail-to-Rail Input Single-Supply Comparator 45ns, Low-Power, 3V/5V, Rail-to-Rail GENERAL DESCRIPTION The is a single high-speed comparator optimized for systems powered from a 3V or 5V supply. The device features high-speed response, low-power consumption,

More information

MCP6041/2/3/ na, Rail-to-Rail Input/Output Op Amps. Features. Description. Applications. Design Aids. Package Types.

MCP6041/2/3/ na, Rail-to-Rail Input/Output Op Amps. Features. Description. Applications. Design Aids. Package Types. 600 na, Rail-to-Rail Input/Output Op Amps Features Low Quiescent Current: 600 na/amplifier Rail-to-Rail Input/Output Gain Bandwidth Product: 14 khz Wide Supply Voltage Range: 1.4V to 6.0V Unity Gain Stable

More information

UNISONIC TECHNOLOGIES CO., LTD UM609A

UNISONIC TECHNOLOGIES CO., LTD UM609A UNISONIC TECHNOLOGIES CO., LTD DUAL OPERATIONAL AMPLIFIER AND CURRENT CONTROLLER DESCRIPTION The UTC is a monolithic IC that includes one independent op-amp and another op-amp for witch the non inverting

More information

Features. Applications SOT-23-5

Features. Applications SOT-23-5 135MHz, Low-Power SOT-23-5 Op Amp General Description The is a high-speed, unity-gain stable operational amplifier. It provides a gain-bandwidth product of 135MHz with a very low, 2.4mA supply current,

More information

CMOS Quad Rail-to-Rail I/O Op Amp DESCRIPTION: FEATURES: Logic Diagram

CMOS Quad Rail-to-Rail I/O Op Amp DESCRIPTION: FEATURES: Logic Diagram 6484 CMOS Quad Rail-to-Rail I/O Op Amp V+ IN+A IN+D IN-A OUT A OUT D IN-D V- IN+B OUT B OUT C IN+C IN-B Logic Diagram IN-C FEATURES: Rad-Pak technology-hardened against natural space radiation Total dose

More information

NJU High Output Current, Rail-to-Rail Input/Output Dual CMOS Operational Amplifier

NJU High Output Current, Rail-to-Rail Input/Output Dual CMOS Operational Amplifier High Output Current, Rail-to-Rail Input/Output Dual CMOS Operational Amplifier NJU779 GENERAL DESCRIPTION The NJU779 is a Rail-to-Rail input and output dual CMOS operational amplifier that features high

More information

Features. Ordering Information. Part Identification

Features. Ordering Information. Part Identification MIC9 MHz Low-Power SC-7 Op Amp General Description The MIC9 is a high-speed operational amplifier with a gain-bandwidth product of MHz. The part is unity gain stable. It has a very low.ma supply current,

More information

NJM324C. Low power quad operational amplifiers

NJM324C. Low power quad operational amplifiers Low power quad operational amplifiers Features Wide gain bandwidth:.mhz typ. Input common-mode voltage range includes ground Large voltage gain:db typ. Very low supply current per amplifier:ua typ. Low

More information

S Series MINI ANALOG SERIES LOW INPUT OFFSET VOLTAGE CMOS OPERATIONAL AMPLIFIER. Features. Applications. Packages.

S Series MINI ANALOG SERIES LOW INPUT OFFSET VOLTAGE CMOS OPERATIONAL AMPLIFIER. Features. Applications. Packages. S-89713 Series www.sii-ic.com MINI ANALOG SERIES LOW INPUT OFFSET VOLTAGE CMOS OPERATIONAL AMPLIFIER SII Semiconductor Corporation, 2009-2016 Rev.3.4_00 The mini-analog series is a group of ICs that incorporate

More information

4-CH BTL DRIVER FOR CD PLAYER WITH 3.3V OUTPUT VOLTAGE

4-CH BTL DRIVER FOR CD PLAYER WITH 3.3V OUTPUT VOLTAGE 4-CH BTL DRIVER FOR CD PLAYER WITH 3.3V OUTPUT VOLTAGE DESCRIPTION The SA1469PH, an IC for CD players, has a 4-channel BTL driver, 3.3V regulator (attached PNP transistor required), standard operational

More information

17µA Max, Dual/Quad, Single-Supply, Precision Op Amps

17µA Max, Dual/Quad, Single-Supply, Precision Op Amps 19-127; Rev. 1; 11/98 General Description The MAX478 and MAX479 are dual and quad micropower, precision op amps available in 8-pin and 14-pin DIP and small-outline packages, respectively. Both devices

More information

10MHz/42MHz Low Noise, Low Bias Op-Amps

10MHz/42MHz Low Noise, Low Bias Op-Amps MAX475/MAX488 1MHz/42MHz Low Noise, Low Bias Op-Amps General Description The MAX475/MAX488 are wideband, low-noise, low-input bias current operational amplifiers offering railto-rail outputs and single-supply

More information

Low Power, Wide Supply Range, Low Cost Unity-Gain Difference Amplifier AD8276

Low Power, Wide Supply Range, Low Cost Unity-Gain Difference Amplifier AD8276 Low Power, Wide Supply Range, Low Cost Unity-Gain Difference Amplifier AD87 FEATURES Wide input range Rugged input overvoltage protection Low supply current: μa maximum Low power dissipation:. mw at VS

More information

LM321 Low Power Single Op Amp

LM321 Low Power Single Op Amp Low Power Single Op Amp General Description The LM321 brings performance and economy to low power systems. With a high unity gain frequency and a guaranteed 0.4V/µs slew rate, the quiescent current is

More information

ELM86xxxxBxA CMOS Dual 400mA LDO Regulator

ELM86xxxxBxA CMOS Dual 400mA LDO Regulator ELM86xxxxBxA CMOS Dual ma LDO Regulator General description ELM86xxxxBxA is dual CMOS Voltage Regulator which consists of large current LDOs. With the chip enable function of each channel, it is possible

More information

Single-Supply, 150MHz, 16-Bit Accurate, Ultra-Low Distortion Op Amps

Single-Supply, 150MHz, 16-Bit Accurate, Ultra-Low Distortion Op Amps 9-; Rev ; /8 Single-Supply, 5MHz, 6-Bit Accurate, General Description The MAX4434/MAX4435 single and MAX4436/MAX4437 dual operational amplifiers feature wide bandwidth, 6- bit settling time in 3ns, and

More information

1.8 V, Micropower, Zero-Drift, Rail-to-Rail Input/Output Op Amp ADA4051-2

1.8 V, Micropower, Zero-Drift, Rail-to-Rail Input/Output Op Amp ADA4051-2 .8 V, Micropower, Zero-Drift, Rail-to-Rail Input/Output Op Amp ADA45-2 FEATURES Very low supply current: 3 μa Low offset voltage: 5 μv maximum Offset voltage drift: 2 nv/ C Single-supply operation:.8 V

More information

Very Low Distortion, Dual-Channel, High Precision Difference Amplifier AD8274 FUNCTIONAL BLOCK DIAGRAM +V S FEATURES APPLICATIONS GENERAL DESCRIPTION

Very Low Distortion, Dual-Channel, High Precision Difference Amplifier AD8274 FUNCTIONAL BLOCK DIAGRAM +V S FEATURES APPLICATIONS GENERAL DESCRIPTION Very Low Distortion, Dual-Channel, High Precision Difference Amplifier AD8273 FEATURES ±4 V HBM ESD Very low distortion.25% THD + N (2 khz).15% THD + N (1 khz) Drives 6 Ω loads Two gain settings Gain of

More information

MIC7300 A17. General Description. Features. Applications. Ordering Information. Pin Configurations. Functional Configuration.

MIC7300 A17. General Description. Features. Applications. Ordering Information. Pin Configurations. Functional Configuration. MIC7300 High-Output Drive Rail-to-Rail Op Amp General Description The MIC7300 is a high-performance CMOS operational amplifier featuring rail-to-rail input and output with strong output drive capability.

More information

Rail-to-Rail, 200kHz Op Amp with Shutdown in a Tiny, 6-Bump WLP

Rail-to-Rail, 200kHz Op Amp with Shutdown in a Tiny, 6-Bump WLP 19-579; Rev ; 12/1 EVALUATION KIT AVAILABLE Rail-to-Rail, 2kHz Op Amp General Description The op amp features a maximized ratio of gain bandwidth (GBW) to supply current and is ideal for battery-powered

More information

Copyright Each Manufacturing Company.

Copyright Each Manufacturing Company. Free DataSheet Search and Download Site. Free electronic engineering tool that enables you to locate product datasheets from hundreds of electronic component manufacturers worldwide. Copyright Each Manufacturing

More information

AVAILABLE OPTIONS CERAMIC DIP (J) 6 mv ua747cd ua747cn. 5 mv ua747mj ua747mw ua747mfk

AVAILABLE OPTIONS CERAMIC DIP (J) 6 mv ua747cd ua747cn. 5 mv ua747mj ua747mw ua747mfk SLOS9A D97, FEBRUARY 97 REVISED OCTOBER 99 No Frequency Compensation Required Low Power Consumption Short-Circuit Protection Offset-Voltage Null Capability Wide Common-Mode and Differential Voltage Ranges

More information

PJ386 Low Voltage Audio Power Amplifier

PJ386 Low Voltage Audio Power Amplifier T he PJ386 is a power amplifier designed for use in low voltage consumer applications. The gain is internally set to 20 to keep external part count low, but the addition of an external resistor and capacitor

More information

Ultra-Small, Rail-to-Rail I/O with Disable, Single-/Dual-Supply, Low-Power Op Amps MAX4245/MAX4246/ MAX4247. Features. General Description

Ultra-Small, Rail-to-Rail I/O with Disable, Single-/Dual-Supply, Low-Power Op Amps MAX4245/MAX4246/ MAX4247. Features. General Description General Description The MAX4245/MAX4246/ family of low-cost op amps offer rail-to-rail inputs and outputs, draw only 32µA of quiescent current, and operate from a single +2.5V to +5.5V supply. For additional

More information

LMC7101 Tiny Low Power Operational Amplifier with Rail-To-Rail Input and Output

LMC7101 Tiny Low Power Operational Amplifier with Rail-To-Rail Input and Output Tiny Low Power Operational Amplifier with Rail-To-Rail Input and Output General Description The LMC7101 is a high performance CMOS operational amplifier available in the space saving SOT 23-5 Tiny package.

More information

DIO20881/2/4 600nA,Rail-to-Rail Input/ Output Low Power Amplifier

DIO20881/2/4 600nA,Rail-to-Rail Input/ Output Low Power Amplifier Rev 0. 600nARailtoRail Input/ Output Low Power Amplifier Features Ultra low power: 600nA per channel Unity Gain Stable Gain Bandwidth Product: 4kHz Wide supply range:.v to.v Available in SOT3 SOIC8 MSOP8

More information

TSV630, TSV630A, TSV631, TSV631A

TSV630, TSV630A, TSV631, TSV631A TSV630, TSV630A, TSV631, TSV631A Rail-to-rail input/output, 60 µa, 880 khz, 5 V CMOS operational amplifiers Datasheet - production data Applications Battery-powered applications Portable devices Active

More information

AOUT AIN- AIN+ GND 1 AOUT 2 AIN- 3 AIN+

AOUT AIN- AIN+ GND 1 AOUT 2 AIN- 3 AIN+ www.dalsemi.com FEATURES High Slew Rate: V/µs High Gain Bandwidth: 6.5 MHz Supply Voltage Range.5 to 5.5V Rail-to-Rail Output Swing.75 ma Supply Current per Channel ORDERING INFORMATION Part Number Description

More information

MCP601/1R/2/3/4. 2.7V to 6.0V Single Supply CMOS Op Amps. Features. Description. Typical Applications. Available Tools.

MCP601/1R/2/3/4. 2.7V to 6.0V Single Supply CMOS Op Amps. Features. Description. Typical Applications. Available Tools. MCP60/R///4.7V to 6.0V Single Supply CMOS Op Amps Features Single-Supply:.7V to 6.0V Rail-to-Rail Output Input Range Includes Ground Gain Bandwidth Product:.8 MHz Unity-Gain Stable Low Quiescent Current:

More information

MCP6271/1R/2/3/4/ µa, 2 MHz Rail-to-Rail Op Amp. Features. Description. Applications. Available Tools. Package Types

MCP6271/1R/2/3/4/ µa, 2 MHz Rail-to-Rail Op Amp. Features. Description. Applications. Available Tools. Package Types MCP627/R/2/3/4/ 70 µa, 2 MHz Rail-to-Rail Op Amp Features Gain Bandwidth Product: 2 MHz (typical) Supply Current: I Q = 70 µa (typical) Supply Voltage: 2.0V to 6.0V Rail-to-Rail Input/Output Extended Temperature

More information

TABLE OF CONTENTS Features... Applications... Pin Configurations... General Description... Revision History... 2 Specifications... 3 Absolute Maximum

TABLE OF CONTENTS Features... Applications... Pin Configurations... General Description... Revision History... 2 Specifications... 3 Absolute Maximum FEATURES Offset voltage: 2.5 mv maximum Single-supply operation: 2.7 V to 5.5 V Low noise: 8 nv/ Hz Wide bandwidth: 24 MHz Slew rate: V/μs Short-circuit output current: 2 ma No phase reversal Low input

More information

LMC6081 Precision CMOS Single Operational Amplifier

LMC6081 Precision CMOS Single Operational Amplifier LMC6081 Precision CMOS Single Operational Amplifier General Description The LMC6081 is a precision low offset voltage operational amplifier, capable of single supply operation. Performance characteristics

More information

Micropower, Rail-to-Rail, 300kHz Op Amp with Shutdown in a Tiny, 6-Bump WLP

Micropower, Rail-to-Rail, 300kHz Op Amp with Shutdown in a Tiny, 6-Bump WLP EVALUATION KIT AVAILABLE MAX46 General Description The MAX46 op amp features a maximized ratio of gain bandwidth (GBW) to supply current and is ideal for batterypowered applications such as handsets, tablets,

More information

Single-Supply, Rail-to-Rail, Low Power FET-Input Op Amp AD820

Single-Supply, Rail-to-Rail, Low Power FET-Input Op Amp AD820 Single-Supply, Rail-to-Rail, Low Power FET-Input Op Amp AD82 FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 5 V

More information

KA741. Single Operational Amplifier. Features. Description. Internal Block Diagram.

KA741. Single Operational Amplifier. Features. Description. Internal Block Diagram. Single Operational Amplifier www.fairchildsemi.com Features Short circuit protection Excellent temperature stability Internal frequency compensation High Input voltage range Null of offset Description

More information

ABLIC Inc., 2014 Rev.1.0_02

ABLIC Inc., 2014 Rev.1.0_02 www.ablicinc.com MINI ANALOG SERIES FOR AUTOMOTIVE 15 C OPERATION LOW INPUT OFFSET VOLTAGE CMOS OPERATIONAL AMPLIFIER ABLIC Inc., 214 The mini-analog series is a group of ICs that incorporate a general

More information

KM4110/KM mA, Low Cost, +2.7V & +5V, 75MHz Rail-to-Rail Amplifiers

KM4110/KM mA, Low Cost, +2.7V & +5V, 75MHz Rail-to-Rail Amplifiers + + www.fairchildsemi.com KM411/KM41.5mA, Low Cost, +.7V & +5V, 75MHz Rail-to-Rail Amplifiers Features 55µA supply current 75MHz bandwidth Power down to I s = 33µA (KM41) Fully specified at +.7V and +5V

More information

TS931ILT/AILT/BILT SOT23-5L Tape & Reel

TS931ILT/AILT/BILT SOT23-5L Tape & Reel Output Rail-to-Rail Micropower Operational Amplifiers n Rail-to-rail output voltage swing n Micropower consumption (µa) n Single supply operation (.7V to V n Low offset (mv max for TS93xB) n CMOS inputs

More information

+3V/+5V, 250MHz, SOT23 ADC Buffer Amplifiers with High-Speed Disable

+3V/+5V, 250MHz, SOT23 ADC Buffer Amplifiers with High-Speed Disable 9-5; Rev ; / +V/+5V, 5MHz, SOT ADC Buffer Amplifiers General Description The MAX85/MAX86 single and MAX87/MAX88/ MAX87/MAX88 dual ADC buffer amplifiers feature high-speed performance and single +V supply

More information

Internally-compensated dual low noise operational amplifier NE/SE5532/5532A

Internally-compensated dual low noise operational amplifier NE/SE5532/5532A Internally-compensated dual low noise operational DESCRIPTION The 5532 is a dual high-performance low noise operational. Compared to most of the standard operational s, such as the 1458, it shows better

More information

High-Speed, Low-Power, 3V/5V, Rail-to-Rail Single-Supply Comparators

High-Speed, Low-Power, 3V/5V, Rail-to-Rail Single-Supply Comparators 19-9; Rev 3; 6/97 High-Speed, Low-Power, 3V/5V, General Description The are single/dual/quad high-speed comparators optimized for systems powered from a 3V or 5V supply. These devices combine high speed,

More information

NE/SA5234 Matched quad high-performance low-voltage operational amplifier

NE/SA5234 Matched quad high-performance low-voltage operational amplifier INTEGRATED CIRCUITS Supersedes data of 2001 Aug 03 File under Integrated Circuits, IC11 Handbook 2002 Feb 22 DESCRIPTION The is a matched, low voltage, high performance quad operational amplifier. Among

More information