PZ-30 PRESSURE INDICATORS P Z N V S T I FEATURES MODEL NUMBER DESIGNATION LIST OF MODEL NUMBERS

Transcription

1 marking patible with EMC directive kinds of display multiplier Full 3-digit red Small 3 mm square face Except for Current output type patible with our analog sensors FETURES Pressure indicators separated from sensor - Can be used with variety of sensors Wide range of applications such as pneu matic equipment or semiconductor equipment ny range of pressure sensors is available Low power consumption by non display mode Set data protection by panel lock function MODEL NUMBER DESIGNTI Series name P Z N V S T I Switch output interface N:NPN open collector P:PNP open collector Blank:Voltage output I:Current output Input signal type V: I: connection type ST:One-touch type terminal CN:Connector type terminal LIST OF MODEL NUMBERS Switch output type Input signal type One-touch type terminal connection type Connector type terminal nalog Current output NPN PNP NPN PNP -NVST -NIST -PVST -PIST -NVSTI -NISTI -PVSTI -PISTI -NVCN -NICN -PVCN -PICN Verify the above model numbers when placing orders. Marked is manufactured upon receipt of order basis.

2 STNDRD SPECIFICTIS Unless otherwise specified, the specs are defined at an ambient temperature of 5±5 C and excitation voltage of 4 V DC. Item Model number Switch Display Imput General specifications Operating temp. range Operating humidity Protection grade Storage temp. Net weight Insulation resistance Dielectric strength Supply voltage Consumption current Input signal Input impedance No. of digit Display element Display cycle Negative pressure display Display accuracy Thermal error Resolution Output status Switching capacity Residual voltage ysteresis setting Repeatability Short circuit protection Response Thermal error State indication C %R C g kω ~ 5 35 ~ 85 IP4 ~ 7 pprox. 8 (Including m cable) MΩ minimum 5 V DC minute.8 ~ 3 V DC(Including ripple percentage) 5 m maximum (V) / (I) kω (V) / 5 Ω (I) 3 pprox. 4 times/s is ± %F.S. (Without sensor's error) ±.5 % ( ~ 5 C, Reference temp. 5 C) count NPN/PNP -point output (Transistor, Open collector output) 3 V DC m maximum. V maximum (NPN),. V maximum (PNP) ~ 3 counts djustable ±. %F.S. ± count With pretection function pprox. 5 ms ( F ) (Selectable 5 ms ~.5 s) ±.5 %F.S. ( ~ 5 C, Refernce temp. 5 C) Output (Green ), Output (Red ) Lighted when output is. Voltage output Current output (5 Ω) When analog current output type of PZ3 is chosen or when a sensor of current output type is connected, supply voltage is 4 V DC ± % ENVIRMENTL CRCTERISTICS Test item Vibration Shock Moisture resistance EMC Test conditions ~ 5 z, 98. m/s or.5 mm P-P, 3 directions for hours each 49 m/s, 3 directions for 3 times each 4 C, 9 ~ 95 %R, 4 hrs. EMI : EN55: 7, : 7 Group, class B EMS : EN636-: 6 Table Permissible change, switch operating points and analog output variation : ± %F.S. maximum each after test, switch operating pressure and analog output : ± 5 %F.S. maximum during test

3 INTERNL ELECTRICL SCEMTICS Voltage analog output Current input NPN output Current input PNP output Is S.Output S.Output mon.output Is S.Output S.Output mon.output Voltage input NPN output Voltage input PNP output Vs S.Output S.Output mon.output Vs S.Output S.Output mon.output When connecting the -wire type of current output sensors, please do not connect the 3 (.) terminal. Current analog output Current input NPN output Current input PNP output Is.Output S.Output S.Output mon Is S.Output S.Output.Output mon Voltage input NPN output Voltage input PNP output Vs.Output S.Output S.Output mon Vs S.Output S.Output.Output mon When connecting the -wire type of current output sensors, please do not connect the 3 (.) terminal.

4 NLOG OUTPUT MODE Pr Pr setting : The second figure in triple digits indicates output mode in the initial setting. Output mode is fixed by rated pressure. Code Output mode R mode (pound) V (Vzero) 5 V (4 m) ( m) G mode (Positive) V 5 V (4 m) ( m) 3 V mode (Negative) 5 V V ( m) (4 m) SWITC OUTPUT MODE Switch output can be set when blinking red indicates (SW) in the intial setting. The mode is set at Separate (/), prior to shipment. The mode is initialized at Separate (L/L), 4 when rated pressure is set at -P or -F (negative pressure). Output SW SW Separate mode Window comparator mode Mode Separate Window comparator Separate Window comparator (I operation) ( operation) Operation S- S- S- 3 S- 4 C- 5 C- 6 C- 7 C- 8 Pressure setting (Operating point) I LO B I LO B P: SW P: SW P P Setting (Lower limit) : Setting (Upper limit) : Setting Setting (Lower limit) : Setting (Upper limit) : Setting -Pr -Pr (LO operation) P: SW P: SW P P or P P P Pr -Pr Pr Pr :Switch hysteresis P=Setting P=Setting -Pr (B operation) P P P Pr Note. In the Separate Mode, setting corresponds to SW, and Setting corresponds to SW. Note. In the Window parator Mode, the minimum value for SW and SW corresponds to Setting and the maximum value corresponds to Setting.

5 SELECTI OF DISPLY MULTIPLIER/RTED PRESSURE Selection of display multiplier Please set any code when blinking red indicates negative pressure in the initial setting. Display multiplier is set at () prior to shipment. Selection of rated pressure Please set any code when blinking red indicates negative pressure, SW, SW in the initial setting. Rated pressure is set at P ( ~ ) prior to shipment. Mode (/3) Display multiplier Code Multiplier () (MPa) b.953 Pressure reference Pressure unit Rated pressure range Setting code Rated pressure display (PL ~ P) ~ P Gauge/bsolute ~ 35 ~ 5 ~ - ~ ~ 35 ~ 5 4P 5P -P P 4P 5P 6P 7P 3P 3P ~ 6 ~ 7 ~ ~ MPa Mode (/3) Display multiplier Code Multiplier () (MPa) b.953 Pressure reference Pressure unit Rated pressure range Setting code Rated pressure display (PL ~ P) ~ P Gauge/bsolute MPa pound ~ 5. ~ ~ ~ ~ - ~ - ~ - ~ 3 - ~ 5 - ~ 6 - ~ 53P 4P 4P 44P r r r 3r 5r 6r 3r

6 SELECTI OF DISPLY MULTIPLIER/RTED PRESSURE Mode (3/3) Display multiplier Code Multiplier () (MPa) b.953 Pressure reference Pressure unit Rated pressure range Setting code Rated pressure display (PL ~ P) ~ F Gauge/bsolute ( / ) ~.35 ~.5 ~ -. ~. ~ 3.5 ~ 5. ~ 7. ~ 4F 5F -F F 4F 5F 7F 3F OUTLINE DIMENSI One-touch type terminal / SW SW (φ4) 5 core cable L = ± WG6 UL No.844 Unless otherwise specified, tolerance: ±.5 (Unit: mm) 3 M3 Depth 6 Window Push button Wire input 8.5 Terminal : OCN-5 manufactured by Osada Wire : WG6 ~6 Wire strip length : 9 ~ mm Connector type terminal M3 Depth 6 +/ SW SW 36.4 (φ4) 5 core cable L = ± WG6 UL No Connector : (Pitch.5) manufactured by Osada (ousing : -78-3) Wire color Brown Gray Black White Blue Connection Switch output Switch output mon

7 OW TO MOUNT OPTIL CCESSORIES <SOLD SEPERTELY> Rear panel mounting bracket set Unless otherwise specified, tolerance: ±.5 (Unit: mm) Panel mounting bracket set (5) φ4. Material : SUS34 (t =.5) Material : SUS34 (t =.5) 5 35 φ4.x5. Slot -M3x4 ssociated screw -M3x4 ssociated screw φ (46) φ4.x5. Slot (.5) (4) (3) (46) Panel holder set (5.7) 3. Recommended : 5 minimum maximum maximum Panel cut dimension (Recommended board thickness : 5 maximum) Panel holder set (PG-3/PG-35) older cover set older stopper set Name Series Name Contents CPG-3 CPG-4 CPG-7 Panel holder cover Panel holder Panel stopper ( pcs.) Panel holder cover Panel holder Panel holder Panel stopper ( pcs.) Rear panel bracket set (Z) CPG- Rear panel bracket set (Z) and M3 4, male screw ( pcs.) Panel bracket set (Z) CPG- Panel panel bracket set (Z) and M3 4, male screw ( pcs.)