v Features = +25 C, 50 Ohm System, Vcc = 5V

Transcription

1 Typical Applications Prescaler for DC to X band PLL applications: Satellite communication systems Fiber optic Point-to-point and point-to-multi-point radios VSAT Functional Diagram Features Ultra low SSB phase noise: -18 dbc/hz Wide bandwidth Output power: 3 dbm Single DC supply: +5V S8G SMT package General Description Electrical Specifications, T A = +25 C, 5 Ohm System, Vcc = 5V The HMC361S8G & HMC361S8GE are low noise divide-by-2 static dividers with InGaP GaAs HBT technology in 8 lead surface mount plastic packages. This device operates from DC (with a square wave input) to 1 GHz input frequency with a single +5V DC supply. The low additive SSB phase noise of -18 dbc/hz at 1 khz offset helps the user maintain good system noise performance. Parameter Conditions Min. Typ. Max. Units Input frequency Sine wave input. [1] [2]. 1 GHz Input power range Fin =. GHz to 1 GHz dbm Fin = 1 GHz to 8 GHz dbm Fin = 8 GHz to 1 GHz dbm Output power Fin = 6 GHz 3 dbm Fin = 1 GHz -6 dbm Reverse leakage Both RF outputs terminated 5 db SSB phase noise (1 khz offset) Pin = dbm, Fin = 6 GHz -18 dbc/hz Output transition time Pin = dbm, Fout = 882 MHz 1 ps Supply current (Icc) 83 ma [1] Divider will operate down to near DC for square-wave input signal. [2] For stable operation without an input signal, refer to Analog Devices Application Note, Frequency Divider Operation & Compensation with No Input Signal tel fax Order online Phone: at Application support: Phone: Application or RFMG-apps@analog.com

2 Input Sensitivity Window, T = 25 C INPUT POWER (dbm) Recommended Operating Window Output Power vs. Temperature OUTPUT POWER (dbm) Output Harmonic Content, Pin = dbm, T = 25 C OUTPUT LEVEL (dbm) C +85 C - C Pfeedthru 3rd Harmonic Input Sensitivity Window vs. Temperature INPUT POWER (dbm) Min Pin +25 C Max Pin +25 C Min Pin +85 C Max Pin +85 C Min Pin - C Max Pin - C Residual Phase Noise Performance, Pin = dbm, T = 25 C SSB PHASE NOISE (dbc/hz) OFFSET FREQUENCY (Hz) Reverse Leakage, Pin = dbm, T = 25 C POWER LEVEL (dbm) Both Output Ports Terminated One Output Port Terminated tel fax Order online Phone: at Application support: Phone: Application or RFMG-apps@analog.com - 2

3 Output Voltage Waveform, Pin = dbm, Fout = 882 MHz, T = 25 C AMPLITUDE (mv) ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing TIME (ns) Absolute Maximum Ratings RF input (Vcc = +5V) Vcc VLogic +13 dbm +5.5V Junction temperature (T J ) 135 C Continuous Pdiss (T = 85 C) (derate 15.9 mw/ C above 85 C) Thermal resistance (R TH ) (junction to ground paddle) Vcc -1.6V to Vcc -1.2V.79 W 63 C/W Storage temperature -65 C to +15 C Operating temperature - C to +85 C Typical Supply Current vs. Vcc Vcc (V) Icc (ma) Note: Divider will operate over full voltage range shown above NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3. DIMENSION DOES NOT INCLUDE MOLDFLASH OF.15 mm PER SIDE.. DIMENSION DOES NOT INCLUDE MOLDFLASH OF.25 mm PER SIDE. 5. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. Package Information Part Number Package Body Material Lead Finish MSL Rating Package Marking [3] [1] H361 HMC361S8G Low stress injection molded plastic Sn/Pb solder MSL1 XXXX [2] H361 HMC361S8GE RoHS-compliant low stress injection molded plastic 1% matte Sn MSL1 XXXX [1] Max peak reflow temperature of 235 C [2] Max peak reflow temperature of 26 C [3] -digit lot number XXXX tel fax Order online Phone: at Application support: Phone: Application or RFMG-apps@analog.com

4 Pin Description Pin Number Function Description Interface Schematic 1 OUT Divided output 18 out of phase with pin 3 and must be DC blocked 2, 6 N/C N/C or ground 3 OUT Divided output, DC block required VCC Supply voltage 5V ±.25V. 5 IN RF input must be DC blocked. 7 IN 8 GND RF input 18 out of phase with pin 5, DC block required for differential operation or A/C ground for single ended applications Ground backside of package has exposed metal ground slug which must be connected to ground tel fax Order online Phone: at Application support: Phone: Application or RFMG-apps@analog.com -

5 Evaluation PCB List of Materials for Evaluation PCB 1631 [1] Item J1 - J3 C1 - C C5 C6 U1 PCB [2] Description PCB mount SMA RF connector 1 pf capacitor, 2 pkg. 1 pf capacitor, 63 pkg. 1 µf tantalum capacitor HMC361S8G / HMC361S8GE divide-by eval board [1] Reference this number when ordering complete evaluation PCB [2] Circuit board material: Rogers 35 The circuit board used in the application should use RF circuit design techniques. Signal lines should have 5 Ω impedance while the package ground leads and backside ground slug should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. This evaluation board is designed for single ended input testing. J2 and J3 provide differential output signals tel fax Order online Phone: at Application support: Phone: Application or RFMG-apps@analog.com

6 Application Circuit tel fax Order online Phone: at Application support: Phone: Application or - 6