FSUSB45 High-Speed USB2.0 (480Mbps) Switch with Dedicated Charger Port Detect

Size: px
Start display at page:

Download "FSUSB45 High-Speed USB2.0 (480Mbps) Switch with Dedicated Charger Port Detect"

Transcription

1 July 2013 FSUSB45 High-Speed USB2.0 (480Mbps) Switch with Dedicated Charger Port Detect Features Low On Capacitance: 7.0 pf Typical Low On Resistance: 3.9 Ω Typical Low Power Consumption: 1 μa Maximum - 15 μa Maximum I CCT over an Expanded Voltage Range (V IN=1.8 V, V CC=4.3 V) Wide -3 db Bandwidth: > 720 MHz Packaged in: - 10-Lead MicroPak (1.6 x 2.1 mm) - 10-Lead UMLP (1.4 x 1.8 mm) 8 kv ESD Rating, >16 kv Power/ ESD Rating Power-Off Protection on All Ports When V CC=0 V - D+/D- Pins Tolerate up to 5.25 V Applications Cell Phone, PDA, Digital Camera, and Notebook LCD Monitor, TV, and Set-Top Box IMPORTANT NOTE: For additional performance information, please contact analogswitch@fairchildsemi.com. Description The FSUSB45 is a bi-directional, low-power, two-port, High-Speed, USB2.0 switch. Configured as a doublepole, double-throw (DPDT) switch, it is optimized for switching between two HS (480 Mbps) sources or an HS source and a Full-Speed (12 Mbps) source. The FSUSB45 is compatible with the requirements of USB2.0 and features an extremely low on capacitance (C ON) of 7.0 pf. The wide bandwidth of this device (720 MHz) exceeds the bandwidth needed to pass the third harmonic, resulting in signals with minimum edge and phase distortion. Superior channel-to-channel crosstalk also minimizes interference. The FSUSB45 contains special circuitry on the switch I/O pins for applications where the V CC supply is powered-off (V CC=0), which allows the device to withstand an over-voltage condition. This device is designed to minimize current consumption even when the control voltage applied to the SEL pin is lower than the supply voltage (V CC). This feature is especially valuable to mobile applications, such as cell phones, allowing for direct interface with the general-purpose I/Os of the baseband processor. An additional feature is the detection of the 1,1 state on D+/D- to signal an interrupt (INT) to the processor when entering a dedicated charging port mode of operation. INT HSD1+ HSD2+ D+ HSD1- HSD2- D- Sel Figure 1. Analog Symbol Ordering Information Part Number Top Mark Operating Temperature Range Package FSUSB45L10X JA -40 to +85 C 10-Lead, MicroPak 1.6 x 2.1 mm, JEDEC MO-255B FSUSB45UMX JB -40 to +85 C MicroPak is a trademark of Fairchild Semiconductor Corporation. 10-Lead, Quad, Ultrathin Molded Leadless Package (UMLP), 1.4 x 1.8 mm FSUSB45 Rev

2 Pin Assignments Vcc Sel INT HSD2+ HSD1+ HSD HSD1- D Sel HSD HSD2-4 9 Vcc D D- D HSD2- HSD1- INT Figure 2. Pad Assignments for MicroPak (Top Through View) Figure 3. Pin Assignments for UMLP (Top Through View) Pin Definitions MicroPak Pin # UMLP Pin # Name Description 9 8 INT Interrupt Signaling Output Pin 1 10 Sel Switch Select 4, 6 3, 5 D+, D- USB Data Bus 2, 3, 7, 8 1, 2, 6, 7 HSDn+, HSDn- Multiplexed Source Inputs 5 4 Ground Truth Table Sel Switch Connection INT Output L D+, D-=HSD1+, HSD1- LOW H D+, D-=HSD2+, HSD2- HIGH FSUSB45 Rev

3 Absolute Maximum Ratings Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol Parameter Min. Max. Unit V CC Supply Voltage V V CNTRL DC Input Voltage (S) (1) -0.5 V CC V V SW DC Switch I/O Voltage (1) V I IK DC Input Diode Current -50 ma I OUT DC Output Current 50 ma T STG Storage Temperature C ESD Human Body Model, JEDEC: JESD22-A114 All Pins 7 I/O to 8 Power to 16 Charged Device Model, JEDEC: JESD22-C101 2 Note: 1. The input and output negative ratings may be exceeded if the input and output diode current ratings are observed. kv Recommended Operating Conditions The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend exceeding them or designing to Absolute Maximum Ratings. Symbol Parameter Min. Max. Unit V CC Supply Voltage V V CNTRL (2) Control Input Voltage (Sel) 0 V CC V V SW Switch I/O Voltage -0.5 V CC V T A Operating Temperature C Note: 2. The control input must be held HIGH or LOW; it must not float. FSUSB45 Rev

4 DC Electrical Characteristics All typical value are at 25 C, V CC=3.3 V unless otherwise specified. Symbol Parameter Conditions V CC (V) T A =- 40ºC to +85ºC Min. Typ. Max. V IK Clamp Diode Voltage I IN=-18 ma V V IH V IL Input Voltage High Input Voltage Low V OH Output Voltage High I OH=-2 ma V OL Output Voltage Low I OL=2 ma Units 3.0 to V V 3.0 to V V 3.0 to to I IN Control Input Leakage V SW=0 to V CC µa I NC(OFF), I NO(OFF) I Dn(ON) I OFF Off State Leakage ON State Leakage Power-Off Leakage Current (All I/O Ports) HSD1n or HSD2n=0 V, 3.6 V or floating, D+/-=0 or 3.6 V HSD1n or HSD2n=0 V, 3.6 V or floating, D+/-=0 or 3.6 V V SW=0 V to 4.3 V, V CC=0 V, Figure 5 (3) VSW=0.4 V, ION=-8 ma, R ON HS Switch On Resistance Figure 4 R ON HS Delta R ON (4) µa µa µa V SW=0.4 V, I ON=-8 ma I CC Quiescent Supply Current V CNTRL=0 or V CC, I OUT= µa I CCT Increase in I CC Current per Control Voltage and V CC V CNTRL=2.6 V, V CC=4.3 V µa V CNTRL=1.8 V, V CC=4.3 V µa Notes: 3. Measured by the voltage drop between HSDn and Dn pins at the indicated current through the switch. On resistance is determined by the lower of the voltage on the two (HSDn or Dn ports). 4. Guaranteed by characterization. V V FSUSB45 Rev

5 AC Electrical Characteristics All typical value are for V CC=3.3 V at 25 C unless otherwise specified. Symbol Parameter Conditions V CC (V) t ON Turn-On Time, S to Output t OFF Turn-Off Time, S to Output RL=50 Ω, CL=5 pf, VSW=0.8 V, Figure 6, Figure 7 RL=50 Ω, CL=5 pf, VSW=0.8V, Figure 6, Figure 7 (5) CL=5 pf, RL=50 Ω, Figure 6, t PD Propagation Delay Figure 8 t BBM Break-Before-Make R L=50 Ω, C L=5 pf, V SW1=V SW2=0.8 V, Figure 12 T A =- 40 to +85 C Min. Typ. Max. Units 3.0 to ns 3.0 to ns ns 3.0 to ns t PLH/HL INT Propagation Delay (5) R L=50 Ω, C L=5 pf 3.0 to ns O IRR Off Isolation R L=50 Ω, f=24 0MHz, Figure to db Xtalk BW Non-Adjacent Channel Crosstalk -3 db Bandwidth Note: 5. Guaranteed by characterization. USB Hi-Speed-Related AC Electrical Characteristics R L=50 Ω, f=240 MHz, Figure to db R L=50 Ω, C L=0 pf, Figure MHz 3.0 to 3.6 R L=50 Ω, C L=5 pf, Figure MHz Symbol Parameter Conditions V CC (V) t SK(P) Skew of Opposite Transitions of C L=5 pf, R L=50 Ω, the Same Output (6) Figure 9 t J Total Jitter (6) t R=t F=500 ps (10-90%) at R L=50 Ω, C L=5 pf, 480 Mbps (PRBS=2 15 1) Note: 6. Guaranteed by characterization. T A =- 40 to +85 C Min. Typ. Max. Units 3.0 to ps 3.0 to ps Capacitance Symbol Parameter Conditions T A =- 40 to +85 C Min. Typ. Max. Units C IN Control Pin Input Capacitance V CC=0 1.5 pf C OUT INT Pin Output Capacitance V CC=0 2.5 pf C ON D+/D- On Capacitance V CC=3.3 V, f=1 MHz, Figure pf C OFF D1n, D2n Off Capacitance V CC=3.3 V, Figure pf FSUSB45 Rev

6 Test Diagrams V ON HSD1n V SW Dn HSD2n A D+, D- VSW I ON Select V Sel = 0 orvcc Sel 0 or VCC R ON = V ON / I ON Figure 4. On Resistance Figure 5. Off/On Leakage Dn t RISE = 2.5ns t FALL = 2.5ns V SW V Sel C L R L,, and C L are functions of the application environment (see AC Tables for specific values) C L includes test fixture and stray capacitance. Figure 6. AC Test Circuit Load R L V CC Input V /OE, V Sel 90% 90% V CC /2 V CC /2 10% 10% V OH 90% 90% Output- V OL t ON t OFF Figure 7. Turn-On / Turn-Off Waveforms t RISE= 500ps t FALL = 500ps +400mV -400mV 10% 0V 90% 90% 10% Output t PHL t PLH Figure 8. Propagation Delay (t Rt F 500ps) Figure 9. Intra-Pair Skew Test t SK(P) Capacitance Meter S V Sel = 0 or V cc Capacitance Meter S V Sel = 0 or V cc Figure 10. Channel Off Capacitance Figure 11. Channel On Capacitance FSUSB45 Rev

7 Test Diagrams (Continued) t RISE = 2.5ns V SW1 V SW2 Dn C L R L V cc Input - V Sel 0V 10% 0.9*V out 90% V cc /2 0.9*V out t BBM V Sel R L,, and C L are functions of the application environment (see AC Tables for specific values) C L includes test fixture and stray capacitance. Figure 12. Break-Before-Make Interval Timing Network Analyzer V IN V S V Sel R T and R T are functions of the application environment (see AC Tables for specific values). Figure 13. Bandwidth Network Analyzer V Sel and R T are functions of the application environment (see AC Tables for specific values). R T V IN R T Off isolation = 20 Log ( / V IN ) Figure 14. Channel Off Isolation V S NC Network Analyzer V IN V S V Sel R T and R T are functions of the application environment (see AC Tables for specific values). Crosstalk = 20 Log ( / V IN ) Figure 15. Non-Adjacent Channel-to-Channel Crosstalk R T FSUSB45 Rev

8 Physical Dimensions 2X 0.10 C 2.10 A B (0.11) 1.62 KEEPOUT ZONE, NO TRACES OR VIAS ALLOWED PIN1 IDENT IS 2X LONGER THAN OTHER LINES TOP VIEW 2X 0.10 C 0.50 (0.35) 10X (0.25) 10X RECOMMENDED LAND PATTERN 0.55 MAX 0.05 C 0.05 C C SIDE VIEW (0.20) DETAIL A D (0.36) 0.56 (0.15) DETAIL A 2X SCALE (0.29) BOTTOM VIEW X X C A B 0.05 C ALL FEATURES NOTES: A. PACKAGE CONFORMS TO JEDEC REGISTRATION MO-255, VARIATION UABD. B. DIMENSIONS ARE IN MILLIMETERS. C. DIMENSIONS AND TOLERANCES PER ASME Y14.5M, D. PRESENCE OF CENTER PAD IS PACKAGE SUPPLIER DEPENDENT. IF PRESENT IT IS NOT INTENDED TO BE SOLDERED AND HAS A BLACK OXIDE FINISH. E. DRAWING FILENAME: MKT-MAC10Arev5. Figure Lead MicroPak Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor s online packaging area for the most recent package drawings: FSUSB45 Rev

9 Physical Dimensions 2X 0.10 C 1.40 A B 1.70 (9X) PIN#1 IDENT TOP VIEW 0.10 C 2X 0.40 (10X) C 0.55 MAX. (0.15) RECOMMENDED LAND PATTERN 0.08 C DETAIL A PIN#1 IDENT SEATING PLANE SIDE VIEW (9X) BOTTOM VIEW DETAIL A SCALE : 2X 6 C (10X) 0.10 C A B 0.05 C LEAD OPTION 1 SCALE : 2X PACKAGE EDGE LEAD OPTION 2 SCALE : 2X (10X) NOTES: X OPTIONAL MINIMIAL TOE LAND PATTERN A. PACKAGE DOES NOT CONFORM TO ANY JEDEC STANDARD. B. DIMENSIONS ARE IN MILLIMETERS. C. DIMENSIONS AND TOLERANCES PER ASME Y14.5M, D. LAND PATTERN RECOMMENDATION IS BASED ON FSC DESIGN ONLY. E. DRAWING FILENAME: MKT-UMLP10Arev5. F. FAIRCHILD SEMICONDUCTOR. Figure Lead Ultrathin Molded Leadless Package (UMLP) Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor s online packaging area for the most recent package drawings: FSUSB45 Rev

10 FSUSB45 Rev FSUSB45 Hi-Speed USB2.0 (480Mbps) Switch with Dedicated Charger Port Detect

11 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Fairchild Semiconductor: FSUSB45L10X FSUSB45UMX

FSUSB45 Hi-Speed USB2.0 (480Mbps) Switch with Dedicated Charger Port Detect

FSUSB45 Hi-Speed USB2.0 (480Mbps) Switch with Dedicated Charger Port Detect December 2009 FSUSB45 Hi-Speed USB2.0 (480Mbps) Switch with Dedicated Charger Port Detect Features Low On Capacitance: 7.0pF Typical Low On Resistance: 3.9Ω Typical Low Power Consumption: 1μA Maximum -

More information

FSUSB43 Low-Power, Two-Port, High-Speed, USB2.0 (480Mbps) Switch

FSUSB43 Low-Power, Two-Port, High-Speed, USB2.0 (480Mbps) Switch FSUSB43 Low-Power, Two-Port, High-Speed, USB2.0 (480Mbps) Switch Features Over-Voltage Tolerance (OVT) on all USB Ports up to 5.25V without External Components Low On Capacitance: 3.7pF Typical Low On

More information

FSUSB63 3:1 High-Speed USB 2.0 Switch / Multiplexer

FSUSB63 3:1 High-Speed USB 2.0 Switch / Multiplexer July 2013 FSUSB63 3:1 High-Speed USB 2.0 Switch / Multiplexer Features Switch Type 3:1 USB Switch USB USB 2.0 High-Speed & Full-Speed Compliant Break-Before-Make Time 126µs R ON 6Ω Typical C ON 6pF Typical

More information

FSUSB46 Hi-Speed USB2.0 (480Mbps) DPST Switch with Dedicated Charger Port Detection

FSUSB46 Hi-Speed USB2.0 (480Mbps) DPST Switch with Dedicated Charger Port Detection March 2013 FSUSB46 Hi-Speed USB2.0 (480Mbps) DPST Switch with Dedicated harger Port Detection Features Low On apacitance: 7.0pF Typical Low On Resistance: 3.9Ω Typical Low Power onsumption: 1μA Maximum

More information

FSUSB30 Low-Power, Two-Port, High-Speed USB 2.0 (480Mbps) Switch

FSUSB30 Low-Power, Two-Port, High-Speed USB 2.0 (480Mbps) Switch Click to see this datasheet in Simplified Chinese! FSUSB30 Low-Power, Two-Port, High-Speed USB 2.0 (480Mbps) Switch Features Low On Capacitance: 3.7pF (Typical) Low On Resistance: 6.5Ω (Typical) Low Power

More information

FSUSB73 3:1 High-Speed USB Multiplexer and Hub Routing Switch

FSUSB73 3:1 High-Speed USB Multiplexer and Hub Routing Switch April 2012 FSUSB73 3:1 High-Speed USB Multiplexer and Hub Routing Switch Features Switch Type 3:1 MUX + Isolation Switch USB USB 2.0 High-Speed & Full-Speed Compliant R ON 6.5Ω C ON ESD (IEC61000-4-2)

More information

FSA3031 Dual High-Speed USB2.0 with Mobile High-Definition Link (MHL )

FSA3031 Dual High-Speed USB2.0 with Mobile High-Definition Link (MHL ) FSA3031 Dual High-Speed USB2.0 with Mobile High-Definition Link (MHL ) Features Low On Capacitance: 4.6 pf/6.75 pf MHL/USB (Typical) Low Power Consumption: 30 μa Maximum Supports MHL Rev. 2.0 Passes 1080

More information

FSA321 USB2.0 Hi-Speed (480Mbps) and Audio Switches with Negative Signal Capability and Built-in Termination on Unselected Audio Paths

FSA321 USB2.0 Hi-Speed (480Mbps) and Audio Switches with Negative Signal Capability and Built-in Termination on Unselected Audio Paths March 2013 FSA321 USB2.0 Hi-Speed (480Mbps) and Audio Switches with Negative Signal Capability and Built-in Termination on Unselected Audio Paths Features Audio: 1.8 Typical On Resistance HS-USB: 8 Typical

More information

FSA3200 Two-Port, High-Speed USB2.0 Switch with Mobile High-Definition Link (MHL )

FSA3200 Two-Port, High-Speed USB2.0 Switch with Mobile High-Definition Link (MHL ) November 2012 FSA3200 Two-Port, High-Speed USB2.0 Switch with Mobile High-Definition Link (MHL ) Features Low On Capacitance: 2.7 pf / 3.1 pf MHL / USB (Typical) Low Power Consumption: 30μA Maximum Supports

More information

FSUSB22 Low-Power, 2-Port, High-Speed USB 2.0 (480Mbps) Switch

FSUSB22 Low-Power, 2-Port, High-Speed USB 2.0 (480Mbps) Switch March 2008 FSUSB22 Low-Power, 2-Port, High-Speed USB 2.0 (480Mbps) Switch Features -40dB Off Isolation at 250MHz -40dB Non-adjacent Channel Crosstalk at 250MHz On Resistance: 4.5Ω Typical (RON) -3dB Bandwidth:

More information

Is Now Part of To learn more about ON Semiconductor, please visit our website at

Is Now Part of To learn more about ON Semiconductor, please visit our website at Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC

More information

FSUSB43 Low-Power, Two-Port, High-Speed, USB2.0 (480Mbps) Switch

FSUSB43 Low-Power, Two-Port, High-Speed, USB2.0 (480Mbps) Switch FSUSB43 Low-Power, Two-Port, High-Speed, USB2.0 (480Mbps) Switch Features Over-Voltage Tolerance (OVT) on all USB Ports up to 5.25V without External Components Low On Capacitance: 3.7pF Typical Low On

More information

FSUSB104 Low-Power, Two-Port, Hi-Speed, USB2.0 (480 Mbps) Switch

FSUSB104 Low-Power, Two-Port, Hi-Speed, USB2.0 (480 Mbps) Switch FSUSB104 Low-Power, Two-Port, Hi-Speed, USB2.0 (480 Mbps) Switch Features Low On Capacitance: 3.7 pf Typical Low On Resistance: 3.9 Ω Typical Low Pow er Consumption: 1 μa Maximum - 15 μa Maximum ICCT over

More information

FSA110 Audio and Wired-OR USB2.0 Hi-Speed (480Mbps) Switch with Negative Signal Capability and Built-in Termination

FSA110 Audio and Wired-OR USB2.0 Hi-Speed (480Mbps) Switch with Negative Signal Capability and Built-in Termination July 2013 FSA110 Audio and Wired-OR USB2.0 Hi-Speed (480Mbps) Switch with Negative Signal Capability and Built-in Termination Features 6pF Typical Switch Off Capacitance for HS USB 2.5Ω Typical On Resistance

More information

FSA2269 / FSA2269TS Low-Voltage Dual-SPDT (0.4 ) Analog Switch with Negative Swing Audio Capability

FSA2269 / FSA2269TS Low-Voltage Dual-SPDT (0.4 ) Analog Switch with Negative Swing Audio Capability July 2013 FSA2269 / FSA2269TS Low-Voltage Dual-SPDT (0.4 ) Analog Switch with Negative Swing Audio Capability Features 0.4 Ω Typical On Resistance (R ON) for +3.0 V Supply 0.25 Ω Maximum RON Flatness for

More information

FSUSB42 Low-Power, Two-Port, High-Speed, USB2.0 (480Mbps) UART Switch

FSUSB42 Low-Power, Two-Port, High-Speed, USB2.0 (480Mbps) UART Switch FSUSB42 Low-Power, Two-Port, High-Speed, USB2.0 (480Mbps) UART Switch Features Low On Capacitance: 3.7 pf Typical Low On Resistance: 3.9 Ω Typical Low Pow er Consumption: 1 μa Maximum - 15 μa Maximum ICCT

More information

FSUSB20 Low-Power 1-Port High-Speed USB (480Mbps) Switch

FSUSB20 Low-Power 1-Port High-Speed USB (480Mbps) Switch FSUSB20 Low-Power 1-Port High-Speed USB (480Mbps) Switch Features 30dB off isolation at 250MHz 30dB non-adjacent channel crosstalk at 250MHz 4.5Ω typical on resistance (R ON ) 3dB bandwidth: >720MHz Low

More information

FSA Ω Low-Voltage Dual DPDT Analog Switch

FSA Ω Low-Voltage Dual DPDT Analog Switch March 2013 FSA2467 0.4Ω Low-Voltage Dual DPDT Analog Switch Features Typical 0.4 On Resistance (R ON ) for +2.7V Supply Features Less then12µa ICCT Current when Sn Input is Lower than V CC 0.25 Maximum

More information

Is Now Part of To learn more about ON Semiconductor, please visit our website at

Is Now Part of To learn more about ON Semiconductor, please visit our website at Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC

More information

FSA2457 Dual DPDT, 5Ω Analog Data Switch

FSA2457 Dual DPDT, 5Ω Analog Data Switch FSA2457 Dual DPDT, 5Ω Analog Data Switch Features Low On Capacitance for Data Path: 12pF Typical Low On Resistance for Data Path: 5Ω Typical Low Pow er Quiescent Consumption: 1μA Maximum Wide -3db Bandw

More information

FSA2268 / FSA2268T Low-Voltage Dual-SPDT (0.4 ) Analog Switch with 16kV ESD

FSA2268 / FSA2268T Low-Voltage Dual-SPDT (0.4 ) Analog Switch with 16kV ESD FSA2268 / FSA2268T Low-Voltage Dual-SPDT (0.4 ) Analog Switch with 16kV ESD Features 0.4Ω Typical On Resistance (R ON) for +3.0V Supply 0.25Ω Maximum R ON Flatness for +3.0V Supply -3db Bandwidth: > 50MHz

More information

FSHDMI04 Wide-Bandwidth Differential Signaling HDMI Switch

FSHDMI04 Wide-Bandwidth Differential Signaling HDMI Switch Click to see this datasheet in Simplified Chinese! Wide-Bandwidth Differential Signaling HDMI Switch Features 1.65 Gbps throughput 8kV ESD protection -26dB non-adjacent channel crosstalk at 825MHz Isolation

More information

Features. Applications

Features. Applications PRELIMINARY DATASHEET IDTHS421V16 Description The IDTHS421V16 is a bi-directional, low power, Quad single-pole, double-throw (SPDT) hybrid switch targeted at dual SIM card multiplexing. It is optimized

More information

FSUSB104 Low-Power, Two-Port, Hi-Speed, USB2.0 (480 Mbps) Switch

FSUSB104 Low-Power, Two-Port, Hi-Speed, USB2.0 (480 Mbps) Switch October 2015 FSUSB104 Low-Power, Two-Port, Hi-Speed, USB2.0 (480 Mbps) Switch Features Low On Capacitance: 3.7 pf Typical Low On Resistance: 3.9 Ω Typical Low Power Consumption: 1 μa Maximum - 15 μa Maximum

More information

Is Now Part of To learn more about ON Semiconductor, please visit our website at

Is Now Part of To learn more about ON Semiconductor, please visit our website at Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC

More information

FSA806 USB2.0 High-Speed (480Mbps), UART, and Audio Switch with Negative Signal Capability

FSA806 USB2.0 High-Speed (480Mbps), UART, and Audio Switch with Negative Signal Capability July 2012 FSA806 USB2.0 High-Speed (480Mbps), UART, and Audio Switch with Negative Signal Capability Features 3:1 Switch Handles: - Audio Headsets - UART - Up to Two High- and Low-Speed USB Data Negative-Swing-Capable

More information

FSA4159 Low-Voltage, 1Ω SPDT Analog Switch with Power-Off Isolation

FSA4159 Low-Voltage, 1Ω SPDT Analog Switch with Power-Off Isolation December 2013 FSA4159 Low-Voltage, 1Ω SPDT Analog Switch with Power-Off Isolation Features Low I CC When the S Input is Lower Than V CC Power-Off Isolation (V CC=0 V) 1 Ω On Resistance (R ON) for 4.5 V

More information

FSAV433 High-Bandwidth (550MHz), 3-Channel, 3:1 Video Switch

FSAV433 High-Bandwidth (550MHz), 3-Channel, 3:1 Video Switch January 2011 FSAV433 High-Bandwidth (550MHz), 3-Channel, 3:1 Video Switch Features Ground between Channels to Optimize Isolation and Reduce Hostile Crosstalk -70dB Non-Adjacent Channel Crosstalk at 30MHz

More information

FT3001 Reset Timer with Configurable Delay

FT3001 Reset Timer with Configurable Delay FT3001 Reset Timer with Configurable Delay Features Delay Times: 3.0, 3.75, 4.5, 6.0 Seconds 1 µa I CC Current Consumption in Standby Primary and Secondary Input Reset Pins Push-Pull and Open-Drain Output

More information

FSSD07 1-Bit / 4-Bit SD/SDIO and MMC Dual-Host Multiplexer

FSSD07 1-Bit / 4-Bit SD/SDIO and MMC Dual-Host Multiplexer March 2012 FSSD07 1-Bit / 4-Bit SD/SDIO and MMC Dual-Host Multiplexer Features On Resistance: 5Ω Typical, V DDC =2.7V f toggle : >75MHz Low On Capacitance: 6pF Typical Low Power Consumption: 2µA Maximum

More information

FSAV MHz, 4-Channel, 2:1 Video Switch

FSAV MHz, 4-Channel, 2:1 Video Switch Features -50dB Off Isolation at 30MHz -80dB Non-Adjacent Channel Crosstalk at 30MHz 3dB Bandwidth: 800MHz On Resistance: 4 (Typical) Low Power Consumption: 1µA (Maximum) Control Input TTL Compatible Applications

More information

Is Now Part of. To learn more about ON Semiconductor, please visit our website at

Is Now Part of. To learn more about ON Semiconductor, please visit our website at Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com Please note: As part of the Fairchild Semiconductor integration, some of the Fairchild orderable part numbers

More information

FST Bit Bus Switch

FST Bit Bus Switch Features 4 Ω Switch Connection between Two Ports Minimal Propagation Delay through the Switch Low I CC Zero Bounce in Flow-through Mode Control Inputs Compatible with TTL Level Description December 2012

More information

Low-Voltage, 1 Ω Dual SPST Analog Switch with Power-Off Isolation. Description

Low-Voltage, 1 Ω Dual SPST Analog Switch with Power-Off Isolation. Description FS1259 Low-Voltage, 1 Ω Dual SPST nalog Switch with Power-Off Isolation Features Power-Off Isolation (V CC =0 V) 1 Ω On Resistance (R ON ) for 4.5V V CC 0.25 Ω Maximum R ON Flatness for 4.5 V V CC Space-Saving,

More information

FSAV430 Low Voltage 1.1GHz, 4-Channel, 2:1 Video Switch

FSAV430 Low Voltage 1.1GHz, 4-Channel, 2:1 Video Switch FSAV430 Low Voltage 1.1GHz, 4-Channel, 2:1 Video Switch Features -40dB Off Isolation at 30MHz -60dB Non-Adjacent Channel Crosstalk at 30MHz 3dB Bandwidth: 1.1GHz On Resistance: 4.5 (Typical) Low Power

More information

NC7SZ66 Low Voltage Single SPST Normally Open Bus Switch

NC7SZ66 Low Voltage Single SPST Normally Open Bus Switch September 2013 NC7SZ66 Low Voltage Single SPST Normally Open Bus Switch Features Broad V CC Operating Range: 1.65 V to 5.5 V Rail-to-Rail Signal Handling Power Down High-Impedance Inputs/Outputs 5 Ω Switch

More information

Is Now Part of To learn more about ON Semiconductor, please visit our website at

Is Now Part of To learn more about ON Semiconductor, please visit our website at Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC

More information

FAN5622 / FAN5624 / FAN5626 Linear LED Drivers with Single-Wire Digital Interface

FAN5622 / FAN5624 / FAN5626 Linear LED Drivers with Single-Wire Digital Interface FAN5622 / FAN5624 / FAN5626 Linear LED Drivers with Single-Wire Digital Interface Features Family of Three Linear Current-Sink LED Drivers that Support 2, 4, or 6 LED Outputs Current Sink Driver for Each

More information

FSA801 USB2.0 High-Speed (480Mbps), UART, and Audio Switch with Negative Signal Capability

FSA801 USB2.0 High-Speed (480Mbps), UART, and Audio Switch with Negative Signal Capability January 2011 FSA801 USB2.0 High-Speed (480Mbps), UART, and Audio Switch with Negative Signal Capability Features 3:1 Switch Handles: - Audio Headsets - UART - Up to Two High- and Low-Speed USB Data USB

More information

FSUSB242. FSUSB242 Type-C USB Port Protection Switch

FSUSB242. FSUSB242 Type-C USB Port Protection Switch FSUSB242 Type-C USB Port Protection Switch Features Fully USB Data Port Protection V DD 0 V 5.5 V (12 V DC tolerant) 18 V to +20 V DC Tolerance on HSD± Port ±25 V IEC 64000 4 5 Surge Protection w/o External

More information

NC7SZ57 / NC7SZ58 TinyLogic UHS Universal Configurable Two-Input Logic Gates

NC7SZ57 / NC7SZ58 TinyLogic UHS Universal Configurable Two-Input Logic Gates NC7SZ57 / NC7SZ58 TinyLogic UHS Universal Configurable Two-Input Logic Gates Features Ultra High Speed Capable of Implementing any Two-Input Logic Functions Typical Usage Replaces Two (2) TinyLogic Gate

More information

FST Bit Bus Switch

FST Bit Bus Switch Features 4Ω Switch Connection between Two Ports Minimal Propagation Delay through the Switch Low I CC Zero Bounce in Flow-through Mode Control Inputs Compatible with TTL Level Description March 2008 Fairchild

More information

Is Now Part of To learn more about ON Semiconductor, please visit our website at

Is Now Part of To learn more about ON Semiconductor, please visit our website at Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC

More information

Order Number Package Number Eco Status Package Description

Order Number Package Number Eco Status Package Description FXL4TD245 Low-Voltage Dual-Supply 4-Bit Signal Translator with Configurable Voltage Supplies and Signal Levels and 3-STATE Outputs and Independent Direction Controls Features Bi-directional interface between

More information

STG3693. Low voltage high bandwidth quad SPDT switch. Features. Description

STG3693. Low voltage high bandwidth quad SPDT switch. Features. Description Low voltage high bandwidth quad SPDT switch Datasheet - production data Features Ultra low power dissipation: I CC = 0.3 µa at T A = 125 C Low on-resistance: R DS(on) = 4 Ω (T A = 25 C) at V CC = 3.0 V

More information

FSA1259 / FSA1259A Low-Voltage, 1Ω Dual SPST Analog Switch with Power-Off Isolation

FSA1259 / FSA1259A Low-Voltage, 1Ω Dual SPST Analog Switch with Power-Off Isolation FS1259 / FS1259 Low-Voltage, 1Ω Dual SPST nalog Switch with Power-Off Isolation Features Power-Off Isolation (=0V) 1Ω On Resistance (R ON) for 4.5V 0.25Ω Maximum R ON Flatness for 4.5V Space-Saving, US8

More information

NC7SZ125 TinyLogic UHS Buffer with Three-State Output

NC7SZ125 TinyLogic UHS Buffer with Three-State Output NC7SZ125 TinyLogic UHS Buffer with Three-State Output January 2014 NC7SZ125 TinyLogic UHS Buffer with Three-State Output Features Ultra-High Speed: t PD 2.6 ns (Typical) into 50 pf at 5 CC High Output

More information

FSA Ω Low-Voltage SPDT Analog Switch

FSA Ω Low-Voltage SPDT Analog Switch F5157 0.4Ω Low-Voltage PDT nalog witch Features Typical 0.4Ω On Resistance (R ON ) for +2.7V upply F5157 Features Less than 12μ I CCT Current When Input is Lower than 0.25Ω Maximum R ON Flatness for +2.7V

More information

CLCUSB30 Low Power, High-Speed (480MSPS) USB 2.0 Analog Switch

CLCUSB30 Low Power, High-Speed (480MSPS) USB 2.0 Analog Switch Data Sheet Comlinear CLCUSB30 Low Power, High-Speed (480MSPS) USB 2.0 Analog Switch F E A T U R E S n ±8kV ESD protection on all pins n 7pF on capacitance n 4.0Ω on resistance n 720MHz -3dB bandwidth n

More information

NC7WZ16 TinyLogic UHS Dual Buffer

NC7WZ16 TinyLogic UHS Dual Buffer NC7WZ16 TinyLogic UHS Dual Buffer Features Ultra-High Speed: t PD 2.4ns (Typical) into 50pF at 5 CC High Output Drive: ±24mA at 3 CC Broad CC Operating Range: 1.65 to 5.5 Matches Performance of LCX when

More information

CLCUSB42 Low Power, High-Speed (480MSPS) USB 2.0 Analog Switch

CLCUSB42 Low Power, High-Speed (480MSPS) USB 2.0 Analog Switch Comlinear CLCUSB42 Low Power, High-Speed (480MSPS) USB 2.0 Analog Switch F E A T U R E S n ±8kV ESD protection on all pins n 7pF on capacitance n 4.0Ω on resistance n 720MHz -3dB bandwidth n

More information

SGM7222 High Speed USB 2.0 (480Mbps) DPDT Analog Switch

SGM7222 High Speed USB 2.0 (480Mbps) DPDT Analog Switch GENERAL DESCRIPTION The SGM7222 is a high-speed, low-power double-pole/ double-throw (DPDT) analog switch that operates from a single 1.8V to 4.3V power supply. SGM7222 is designed for the switching of

More information

WAS4729QB QB* WAS4729QB. Descriptions. Features. Applications. Order information

WAS4729QB QB* WAS4729QB. Descriptions. Features. Applications. Order information WAS4729QB Low On Resistance (0.75Ω) Dual SPDT Analog Switch with Negative Swing Audio Capability Http//:www.sh-willsemi.com Descriptions The WAS4729QB is a high performance, dual Single Pole Double Throw

More information

MM74HC86 Quad 2-Input Exclusive OR Gate

MM74HC86 Quad 2-Input Exclusive OR Gate MM74HC86 Quad 2-Input Exclusive OR Gate Features Typical Propagation Delay: 9ns Wide Operating oltage Range: 2 6 Low Input Current: 1mA Maximum Low Quiescent Current: 20mA Max. (74 Series) Output Drive

More information

Low-Power, Two-Port, High-Speed, USB2.0 (480Mbps) DPDT Analog Switch BL1530

Low-Power, Two-Port, High-Speed, USB2.0 (480Mbps) DPDT Analog Switch BL1530 DPDT USB2.0 Analog Switch Low-Power, Two-Port, High-Speed, USB2.0 (480Mbps) DPDT Analog Switch Description The is a Low-Power, Two-Port, High-Speed, USB2.0 (480Mbps) double pole double-throw (DPDT) Analog

More information

WAS4723Q WAS4723Q. Order information 1 2 VCC NO1. Low On Resistance, Dual SPDT Analog Switch. Http//: QFN L

WAS4723Q WAS4723Q. Order information 1 2 VCC NO1. Low On Resistance, Dual SPDT Analog Switch. Http//:  QFN L WAS4723Q Low On Resistance, Dual SPDT Analog Switch Http//:www.willsemi.com Descriptions The WAS4723Q is a high performance, dual Single Pole Double Throw (SPDT) analog switch that features ultra-low Ron

More information

BCT4222B 350MHz DPDT Analog Switch

BCT4222B 350MHz DPDT Analog Switch BCT4222B 350MHz DPDT Analog Switch Features VCC Operating Range: 1.65V to V Rail-to-Rail Signal Range ON-Resistance Matching: 0.04 Ω (TYP) ON-Resistance Flatness: 0.08Ω (TYP) High Off Isolation: 58dB at

More information

PI3USB10LP-A. USB 2.0 High-Speed (480 Mbps) Signal Switch Targeted for Battery Powered Applications. Description. Features.

PI3USB10LP-A. USB 2.0 High-Speed (480 Mbps) Signal Switch Targeted for Battery Powered Applications. Description. Features. Features USB 2.0 compliant (high speed and full speed) R ON is 5.5Ω typical @ V CC = 3.0V Low bit-to-bit skew Low Crosstalk: 40dB @ 500 Mbps Off Isolation: 35dB @ 500 Mbps Near-Zero propagation delay:

More information

STMUX1000LQTR GIGABIT LAN ANALOG SWITCH 16-BIT TO 8-BIT MULTIPLEXER

STMUX1000LQTR GIGABIT LAN ANALOG SWITCH 16-BIT TO 8-BIT MULTIPLEXER GIGABIT LAN ANALOG SWITCH 16-BIT TO 8-BIT MULTIPLEXER LOW R ON : 5.5 TYPICAL V CC OPERATING RANGE: 3.0 TO 3.6 V LOW CURRENT CONSUMPTION: 20 µa ESD HBM MODEL: > 2 KV CHANNEL ON CAPACITANCE: 7.5 pf TYPICAL

More information

NC7SV05 TinyLogic ULP-A Inverter (Open-Drain Output)

NC7SV05 TinyLogic ULP-A Inverter (Open-Drain Output) NC7SV05 TinyLogic ULP-A Inverter (Open-Drain Output) Features 0.9V to 3.6V V CC Supply Operation 3.6V Over-Voltage Tolerant I/Os at VCC from 0.9V to 3.6V Extremely High Speed tpd - 1.0ns: Typical for 2.7V

More information

FSA2257 Low R ON Low-Voltage Dual SPDT Bi-Directional Analog Switch

FSA2257 Low R ON Low-Voltage Dual SPDT Bi-Directional Analog Switch F2257 Low R ON Low-Voltage Dual PDT Bi-Directional nalog witch Features Maximum 1.15Ω On Resistance (R ON ) for 4.5V upply 0.3Ω Maximum R ON Flatness for +5V upply pace-aving MicroPak Packaging Broad Operating

More information

BCT4222B BCT4222B. High-Speed DPDT Analog Switch. General Description. Features. Connection Diagram. Applications

BCT4222B BCT4222B. High-Speed DPDT Analog Switch. General Description. Features. Connection Diagram. Applications BCT4222B Features V CC Operating Range: 1.65V to V Rail-to-Rail Signal Range ON-Resistance Matching: 0.05 (TYP) ON-Resistance Flatness: 0.08 (TYP) High Off Isolation: 57dB at 10MHz 54dB (10MHz) Crosstalk

More information

NC7SV57 / NC7SV58 TinyLogic ULP-A Universal Configurable Two-Input Logic Gates

NC7SV57 / NC7SV58 TinyLogic ULP-A Universal Configurable Two-Input Logic Gates December 2010 NC7S57 / NC7S58 TinyLogic ULP-A Universal Configurable Two-Input Logic Gates Features 0.9 to 3.6 CC Supply Operation 3.6 Over-oltage Tolerant I/Os at CC from 0.9 to 3.6 Extremely High Speed

More information

FSAT66 Low Voltage Single SPST Normally Open Analog Switch with TTL Compatible Control Input

FSAT66 Low Voltage Single SPST Normally Open Analog Switch with TTL Compatible Control Input April 2003 Revised July 2004 FSAT66 Low Voltage Single SPST Normally Open Analog Switch with TTL Compatible Control Input General Description The FSAT66 is a high speed single pole/single throw normally

More information

Description. Applications

Description. Applications 2:1 MIPI 4-Data Lane Switch Features ÎÎ4-lane, 2:1 switches that support DHY ÎÎData rate: 2. Gbps ÎÎSupports 2:1 clock differential signal ÎÎ-3 db Bandwidth: 4. GHz Typical ÎÎLow Crosstalk: -30 db@1.2

More information

FST32X Bit Bus Switch

FST32X Bit Bus Switch FST32X245 16-Bit Bus Switch General Description The Fairchild Switch FST32X245 provides 16-bits of high speed CMOS TTL-compatible bus switching in a standard flow-through mode. The low On Resistance of

More information

STG3220. Low voltage high bandwidth dual SPDT switch. Features. Description. Applications

STG3220. Low voltage high bandwidth dual SPDT switch. Features. Description. Applications Low voltage high bandwidth dual SPDT switch Features Ultra low power dissipation: I CC = 1 μa (max.) at T A = 85 C Low "ON" resistance: R ON = 4.8 Ω (T A = 25 ºC) at V CC = 4.3 V R ON = 5.9 Ω (T A = 25

More information

TOP VIEW COM2. Maxim Integrated Products 1

TOP VIEW COM2. Maxim Integrated Products 1 19-3472; Rev ; 1/4 Quad SPST Switches General Description The quad single-pole/single-throw (SPST) switch operates from a single +2V to +5.5V supply and can handle signals greater than the supply rail.

More information

NC7WZ07 TinyLogic UHS Dual Buffer (Open-Drain Outputs)

NC7WZ07 TinyLogic UHS Dual Buffer (Open-Drain Outputs) April 2013 NC7WZ07 TinyLogic UHS Dual Buffer (Open-Drain Outputs) Features Ultra-High Speed: t PZL 2.3 ns (Typical) High I OL Output Drive: ±24 ma at 3 CC Broad CC Operating Range: 1.65 to 5.50 Power Down

More information

STMUX3040. NEATSwitch : octal SPDT high bandwidth signal switch. Features. Description. Applications

STMUX3040. NEATSwitch : octal SPDT high bandwidth signal switch. Features. Description. Applications NEATSwitch : octal SPDT high bandwidth signal switch Features Supports 3.0 Gbps generic data rate Octal SPDT switch to support 2 PCI lanes Low R ON : 5.5 Ω typical Internal voltage regulator V CC operating

More information

BCT MHz DPDT Analog Switch for USB2.0 Hi-Speed

BCT MHz DPDT Analog Switch for USB2.0 Hi-Speed BCT4227 700MHz DPDT Analog Switch for USB2.0 Hi-Speed Features VCC Operating Range: 1.65V to V Rail-to-Rail Signal Range ON-Resistance Matching: 0.05 Ω (TYP) ON-Resistance Flatness: 0.08Ω (TYP) High Off

More information

74AC14, 74ACT14 Hex Inverter with Schmitt Trigger Input

74AC14, 74ACT14 Hex Inverter with Schmitt Trigger Input 74AC14, 74ACT14 Hex Inverter with Schmitt Trigger Input Features I CC reduced by 50% Outputs source/sink 24mA 74ACT14 has TTL-compatible inputs Ordering Information Order Number General Description Package

More information

NC7SZ157 TinyLogic UHS 2-Input Non-Inverting Multiplexer

NC7SZ157 TinyLogic UHS 2-Input Non-Inverting Multiplexer NC7SZ157 TinyLogic UHS 2-Input Non-Inverting Multiplexer Features Broad CC Operating Range: 1.65 to 5.5 Ultra High-Speed Power Down High-Impedance Inputs/Outputs Over-oltage Tolerance Inputs Facilitate

More information

WAS4899Q WAS4899Q. Descriptions. Features. Order information. Applications. Low On Resistance, Quad SPDT Analog Switch. Http//:

WAS4899Q WAS4899Q. Descriptions. Features. Order information. Applications. Low On Resistance, Quad SPDT Analog Switch. Http//: WAS4899Q Low On Resistance, Quad SPDT Analog Switch Http//:www.willsemi.com Descriptions The WAS4899Q is a high performance, quad, Single Pole Double Throw (SPDT) analog switch that features ultra-low

More information

PI5A23159 Low Voltage Dual SPDT 0.8Ω Analog Switch

PI5A23159 Low Voltage Dual SPDT 0.8Ω Analog Switch Features CMOS Technology for Bus and Analog Applications Low On-Resistance: 0.8 at 3.0V Wide Range: 1.65V to 5.5V Rail-to-Rail Signal Range Control Overvoltage Tolerance: 5.5V(Min) Fast Transition Speed:

More information

STG3693. Low voltage high bandwidth Quad SPDT switch. Features. Description

STG3693. Low voltage high bandwidth Quad SPDT switch. Features. Description Low voltage high bandwidth Quad SPDT switch Features Ultra low power dissipation: I CC = 0.2μA (Max.) at T A = 85 C Low ON resistance: R ON = 4Ω (T A = 25 C) at V CC = 3.0V Wide operating voltage range:

More information

FAN5622 / FAN5624 / FAN5626 Linear LED Drivers with Single-Wire Digital Interface

FAN5622 / FAN5624 / FAN5626 Linear LED Drivers with Single-Wire Digital Interface FAN5622 / FAN5624 / FAN5626 Linear LED Drivers with Single-Wire Digital Interface Features Family of Three Linear Current-Sink LED Drivers that Support 2, 4, or 6 LED Outputs Current Sink Driver for Each

More information

NC7SZ00 TinyLogic UHS Two-Input NAND Gate

NC7SZ00 TinyLogic UHS Two-Input NAND Gate NC7SZ00 TinyLogic UHS Two-Input NAND Gate Features Ultra-High Speed: t PD 2.4ns (Typical) into 50pF at 5 CC High Output Drive: ±24mA at 3 CC Broad CC Operating Range: 1.65 to 5.5 Matches Performance of

More information

FXMA2104 Dual-Supply, 4-Bit Voltage Translator / Buffer / Repeater / Isolator for Open-Drain Applications

FXMA2104 Dual-Supply, 4-Bit Voltage Translator / Buffer / Repeater / Isolator for Open-Drain Applications FXMA2104 Dual-Supply, 4-Bit Voltage Tralator / Buffer / Repeater / Isolator for Open-Drain Applicatio Features Bi-Directional Interface between Any Two Levels: 1.65V to 5.5V Direction Control not Needed

More information

FXWA9306 Dual Bi-Directional I 2 C-Bus and SMBus Voltage- Level Translator

FXWA9306 Dual Bi-Directional I 2 C-Bus and SMBus Voltage- Level Translator FXWA9306 Dual Bi-Directional I 2 C-Bus and SMBus Voltage- Level Tralator Features 2-Bit Bi-Directional Tralator for SDA and SCL Lines in Mixed-Mode I 2 C-Bus Applicatio Standard-Mode, Fast-Mode, and Fast-Mode-Plus

More information

Is Now Part of To learn more about ON Semiconductor, please visit our website at

Is Now Part of To learn more about ON Semiconductor, please visit our website at Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC

More information

Is Now Part of To learn more about ON Semiconductor, please visit our website at

Is Now Part of To learn more about ON Semiconductor, please visit our website at Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC

More information

Dual Supply, 2-Bit Voltage Translator / Buffer / Repeater / Isolator for I 2 C Applications

Dual Supply, 2-Bit Voltage Translator / Buffer / Repeater / Isolator for I 2 C Applications FXMA2102 Dual Supply, 2-Bit Voltage Tralator / Buffer / Repeater / Isolator for I 2 C Applicatio Features Bi-Directional Interface between Any Two Levels: 1.65 V to 5.5 V Direction Control not Needed System

More information

Is Now Part of To learn more about ON Semiconductor, please visit our website at

Is Now Part of To learn more about ON Semiconductor, please visit our website at Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC

More information

NLAS7222B, NLAS7222C. High-Speed USB 2.0 (480 Mbps) DPDT Switches

NLAS7222B, NLAS7222C. High-Speed USB 2.0 (480 Mbps) DPDT Switches High-Speed USB 2.0 (480 Mbps) DPDT Switches ON Semiconductor s NLAS7222B and NLAS7222C are part of a series of analog switch circuits that are produced using the company s advanced sub micron CMOS technology,

More information

FSA3200 Two-Port, High-Speed USB2.0 Switch with Mobile High-Definition Link (MHL )

FSA3200 Two-Port, High-Speed USB2.0 Switch with Mobile High-Definition Link (MHL ) FSA3200 Two-Port, High-Speed USB2.0 Switch with Mobile High-Definition Link (MHL ) Features Low On Capacitance: 2.7 pf / 3.1 pf MHL / USB (Typical) Low Pow er Consumption: 30μA Maximum Supports MHL Rev.

More information

Low voltage high bandwidth dual single-pole double-throw analog switch. Description. Table 1. Device summary. Order code Package Packaging

Low voltage high bandwidth dual single-pole double-throw analog switch. Description. Table 1. Device summary. Order code Package Packaging Low voltage high bandwidth dual single-pole double-throw analog switch Applications Datasheet - production data Wearable Sport and fitness Portable equipment Features QFN10 (1.8 x 1.4 mm) Ultra low power

More information

TOP VIEW COUT1 COM2. Maxim Integrated Products 1

TOP VIEW COUT1 COM2. Maxim Integrated Products 1 19-77; Rev ; 7/4.75Ω, Dual SPDT Audio Switch with General Description The dual, single-pole/double-throw (SPDT) switch operates from a single +2V to +5.5V supply and features rail-to-rail signal handling.

More information

PI5A4684. Chip Scale Packaging, Dual SPDT Analog Switch. Features. Description. Pin Configuration/ Block Diagram (top view) CSP.

PI5A4684. Chip Scale Packaging, Dual SPDT Analog Switch. Features. Description. Pin Configuration/ Block Diagram (top view) CSP. Features CMOS Technology for Bus and Analog Applications Low On-Resistance: 0.5Ω. Wide Range: 1.65V to 5.5V Rail-to-Rail Signal Range Control Input Overvoltage Tolerance: 5.5V min. High Off Isolation:

More information

FAN MHz TinyBoost Regulator with 33V Integrated FET Switch

FAN MHz TinyBoost Regulator with 33V Integrated FET Switch FAN5336 1.5MHz TinyBoost Regulator with 33V Integrated FET Switch Features 1.5MHz Switching Frequency Low Noise Adjustable Output Voltage Up to 1.5A Peak Switch Current Low Shutdown Current:

More information

FSTD Bit Bus Switch with Level Shifting

FSTD Bit Bus Switch with Level Shifting FSTD16861 20-Bit Bus Switch with Level Shifting General Description The Fairchild Switch FSTD16861 provides 20-bits of highspeed CMOS TTL-compatible bus switching. The low On Resistance of the switch allows

More information

FXMAR2104 Dual-Supply, 4-Bit Voltage Translator / Isolator for Open-Drain and Push-Pull Applications

FXMAR2104 Dual-Supply, 4-Bit Voltage Translator / Isolator for Open-Drain and Push-Pull Applications FXMAR2104 Dual-Supply, 4-Bit Voltage Tralator / Isolator for Open-Drain and Push-Pull Applicatio Features Bi-Directional Interface between Any Two Levels: 1.65V to 5.5V Direction Control Not Needed Internal

More information

FXMAR2102 Dual-Supply, 2-Bit Voltage Translator / Isolator for I 2 C Applications

FXMAR2102 Dual-Supply, 2-Bit Voltage Translator / Isolator for I 2 C Applications FXMAR2102 Dual-Supply, 2-Bit oltage Tralator / Isolator for I 2 C Applicatio Features Bi-Directional Interface between Any Two Levels: 1.65 to 5.5 No Direction Control Needed Internal 10K Pull-Up Resistors

More information

FST Bit Bus Switch

FST Bit Bus Switch FST3126 4-Bit Bus Switch General Description The Fairchild Switch FST3126 provides four high-speed CMOS TTL-compatible bus switches. The low on resistance of the switch allows inputs to be connected to

More information

FST Bit Low Power Bus Switch

FST Bit Low Power Bus Switch FST3384 10-Bit Low Power Bus Switch General Description The Fairchild Switch FST3384 provides 10 bits of highspeed CMOS TTL-compatible bus switches. The low on resistance of the switch allows inputs to

More information

FIN424C / FIN425C 20-Bit Ultra-Low-Power Serializer / Deserializer for µcontroller and RGB Displays

FIN424C / FIN425C 20-Bit Ultra-Low-Power Serializer / Deserializer for µcontroller and RGB Displays November 2009 FIN424C / FIN425C 20-Bit Ultra-Low-Power Serializer / Deserializer for µcontroller and RGB Displays Features Data & Control Bits 20 Frequency 10MHz Capability QVGA Interface Microcontroller

More information

NC7SZ08 TinyLogic UHS Two-Input AND Gate

NC7SZ08 TinyLogic UHS Two-Input AND Gate NC7SZ08 TinyLogic UHS Two-Input AND Gate Features Ultra-High Speed: t PD 2.7ns (Typical) into 50pF at 5 CC High Output Drive: ±24mA at 3 CC Broad CC Operating Range: 1.65 to 5.5 Matches Performance of

More information

USB1T11A Universal Serial Bus Transceiver

USB1T11A Universal Serial Bus Transceiver Features Complies with Universal Serial Bus Specification 1.1 Utilizes Digital Inputs and Outputs to Transmit and Receive USB Cable Data Supports 12Mbit/s Full Speed and 1.5Mbit/s Low Speed Serial Data

More information

NC7SZ74 TinyLogic UHS D-Type, Flip-Flop with Preset and Clear

NC7SZ74 TinyLogic UHS D-Type, Flip-Flop with Preset and Clear NC7SZ74 TinyLogic UHS D-Type, Flip-Flop with Preset and Clear Features Ultra-High Speed: t PD 2.6 (Typical) into 50pF at 5 CC High Output Drive: ±24mA at 3 CC Broad CC Operating Range: 1.65 to 5.5 Power

More information

0.39, Low-R ON, Ultra-Low Distortion, Compact DPDT Analog Switch

0.39, Low-R ON, Ultra-Low Distortion, Compact DPDT Analog Switch .39, Low-R ON, Ultra-Low Distortion, Compact DPDT Analog Switch DESCRIPTION The is a compact, low resistance, ultra-low distortion double pole double throw (DPST) analog switch. The features a flat.39

More information