Total solder points: 91 Difficulty level: beginner advanced 2 CHANNEL RF RECEIVER K8057 ILLUSTRATED ASSEMBLY MANUAL
|
|
|
- Marylou Peters
- 5 years ago
- Views:
Transcription
1 Total solder points: 91 Difficulty level: beginner advanced 2 CHANNEL RF RECEIVER K8057 For use with K8059/VM108 2 Channel RF transmitter ILLUSTRATED ASSEMBLY MANUAL H8057IP-1
2 Assembly hints 1. Assembly (Skipping this can lead to troubles! ) Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully. 1.1 Make sure you have the right tools: A good quality soldering iron (25-40W) with a small tip. Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called thinning and will protect the tip, and enables you to make good connections. When solder rolls off the tip, it needs cleaning. Thin raisin-core solder. Do not use any flux or grease. A diagonal cutter to trim excess wires. To avoid injury when cutting excess leads, hold the lead so they cannot fly towards the eyes. Needle nose pliers, for bending leads, or to hold components in place. Small blade and Phillips screwdrivers. A basic range is fine. 2 For some projects, a basic multi-meter is required, or might be handy 1.2 Assembly Hints : Make sure the skill level matches your experience, to avoid disappointments. Follow the instructions carefully. Read and understand the entire step before you perform each operation. Perform the assembly in the correct order as stated in this manual Position all parts on the PCB (Printed Circuit Board) as shown on the drawings. Values on the circuit diagram are subject to changes. Values in this assembly guide are correct* Use the check-boxes to mark your progress. Please read the included information on safety and customer service * Typographical inaccuracies excluded. Always look for possible last minute manual updates, indicated as NOTE on a separate leaflet
3 Assembly hints 1.3 Soldering Hints : 1- Mount the component against the PCB surface and carefully solder the leads 2- Make sure the solder joints are cone-shaped and shiny 3- Trim excess leads as close as possible to the solder joint REMOVE THEM FROM THE TAPE ONE AT A TIME! AXIAL COMPONENTS ARE TAPED IN THE CORRECT MOUNTING SEQUENCE! You will find the colour code for the resistances and the LEDs in the HALG (general manual) and on our website: 3
4 Construction / Bouw / Montage / Montaje 1. Diodes / Diode / Diodo D1 : 1N4148 D2 : 1N4148 D3 : 1N4007 D4 : 1N4007 D5 : 1N4007 D6 : 1N4007 CATHODE Watch the polarity! - Let op de polariteit! Attention à la polarité! - Achten Sie auf die Polarität! - Controle la polaridad! 2. Resistors / Weerstanden / Résistances / Widerstände / Resistencias R... D IC socket / IC voetje / support de CI / IC-Fassung / Zócalo de integrado IC1 : 8p Pay attention of the notch! Let op de positie van de nok! Attention à la position de l encoche! Achten Sie auf des position des Nockens! Atención a la posición del la muesca! 4. Capacitors / Kondensatoren / Condensateurs / Kondensatoren / Condensadores 6. Voltage regulator / Spanningsregelaar / Régulateur de tension / Spannungsregler / Regulador de tensión VR1 : UA78L05 VR Push button / Drukknop / bouton-poussoir / Druckknöpfe / Pulsador SW1 : KRS0610 SW... R1 : 330 ( B) R2 : 330 ( B) R3 : 330 ( B) R4 : 330 ( B) R5 : 47K ( B) R6 : 47K ( B) 4 C1 : 100nF (104) C2 : 100nF (104) 5. Transistor T1 : BC547B T2 : BC547B 8. DC-jack / DC connector / Connecteur CC / DC - Einbaubuchse / Conector CC SK1 SK... + SW -
5 Construction / Bouw / Montage / Montaje 9. Receiver module / Ontvangstmodule / Module récepteur / Empfängermodul / Módulo de recepción RX1 : 433MHz. 10. Screw terminal / schroefconnectoren / connecteurs à visser / Schraubconnectoren / Regletas de conexión SK2 : 2p. SK3 : 3p. SK4 : 3p.! 11. Electrolytic Capacitors / Electrolytische condensatoren / Condensateurs électrolytiques / Elektrolytkondensatoren / Condensadores electrolíticos C4 : 100µF C5 : 10µF Watch the polarity! Let op de polariteit! Attention à la polarité! Achten Sie auf die Polarität! Controle la polaridad! 12. Relays / Relais / Relés RY1 : V3SM121C (12VDC - 3A - 1 c) RY2 : V3SM121C (12VDC - 3A - 1 c) RY... C LEDs CATHODE COLOR= IC / CI LD... LD1 : 3mm RED LD2 : 3mm RED LD3 : 3mm RED LD4 : 3mm RED 1 16mm Watch the polarity! Let op de polariteit! Attention à la polarité! Achten Sie auf die Polarität! Controle la polaridad! IC1 : VK8057 VK8057=(Programmed PIC12F629) Pay attention of the notch! Let op de positie van de nok! Attention à la position de l encoche! Achten Sie auf des position des Nockens! Atención a la posición del la muesca! 5
6 Construction / Bouw / Montage / Montaje 15. Antenna / Antenne / Antena 16. PCB / Print layout / Circuit imprimé / Leiterplatten-Lay-out / Circuit integrado Solder Solder a 30cm / 0.5mm² wire (option) for an improved reception quality. Soldeer een draad van 30cm / 0.5mm² (optie) voor een betere ontvangst. Soudez un fil de 30cm / 0.5mm² (option) pour une meilleure réception. Löten Sie einen Draht von 30cm/0.5mm² (optional) wenn Sie einen besseren Empfang wünschen. Suelde un hilo de 30cm / 0,5mm² (opción) si quiere una mejor recepción 6
7 17. Schematic diagram / Schema / Schematisches diagram / Diagrama esquemática Schematic diagram 7
8 VELLEMAN Components NV Legen Heirweg Gavere Belgium Europe Modifications and typographical errors reserved Velleman Components nv. H8057IP ED
Total solder points: 198 Difficulty level: beginner advanced DUAL ELECTRONIC DICE K3400 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 198 Difficulty level: beginner 1 2 3 4 5 advanced DUAL ELECTRONIC DICE K3400 Cheating is no longer possible! ILLUSTRATED ASSEMBLY MANUAL H3400IP-1 Features & Specifications Features:
Total solder points: 247 Difficulty level: beginner advanced. 10 Channel, 2-Wire REMOTE CONTROL K8023 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 247 Difficulty level: beginner 1 2 3 4 5 advanced 10 Channel, 2-Wire REMOTE CONTROL K8023 Control up to 10 devices from a distance using only 2 wires. ILLUSTRATED ASSEMBLY MANUAL H8023IP-1
Total solder points: 63 Difficulty level: beginner advanced 2 CHANNEL RF CODELOCK TRANSMITTER K8059 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 63 Difficulty level: beginner 1 2 3 4 5 advanced 2 CHANNEL RF CODELOCK TRANSMITTER K8059 For use with K8057/VM109 2 Channel RF receiver ILLUSTRATED ASSEMBLY MANUAL H8059IP-1 VELLEMAN
Total solder points: Difficulty level: beginner advanced 3 DIGIT PANEL METER KIT K2032 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 65 + 49 Difficulty level: beginner 1 2 3 4 5 advanced 3 DIGIT PANEL METER KIT K2032 Ideal replacement for moving coil meters ILLUSTRATED ASSEMBLY MANUAL H2032IP-1 Features & Specifications
Total solder points: 338 Difficulty level: beginner advanced. Remote control by telephone K6501 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 338 Difficulty level: beginner 1 2 3 4 5 advanced Remote control by telephone K6501 Operate your appliances from anywhere with a simple phone call. ILLUSTRATED ASSEMBLY MANUAL H6501IP-1
Total solder points: 77 Difficulty level: beginner advanced OPTICAL PROXIMITY SWITCH K8092 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 77 Difficulty level: beginner 1 2 3 4 5 advanced OPTICAL PROXIMITY SWITCH K8092 Operate by waving hand or object in front of unit ILLUSTRATED ASSEMBLY MANUAL H8092IP-1 Features & Specifications
Total solder points: 33 Difficulty level: beginner advanced. 7W mono amplifier K4001 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 33 Difficulty level: beginner 1 2 3 4 5 advanced 7W mono amplifier K4001 Small but powerful multipurpose amplifier. ILLUSTRATED ASSEMBLY MANUAL H4001IP-1 2 Features & Specifications
Total solder points: 163 Difficulty level: beginner advanced SPEAKER PROTECTION KIT K4700 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 163 Difficulty level: beginner 1 2 3 4 5 advanced SPEAKER PROTECTION KIT K4700 Protects your precious speakers against switch-on clicks and DC current. ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 42 Difficulty level: beginner advanced UNIVERSAL STEREO PRE - AMPLIFIER K2572 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 42 Difficulty level: beginner 1 2 3 4 5 advanced UNIVERSAL STEREO PRE - AMPLIFIER K2572 Low noise preamplifier to boost small signals. ILLUSTRATED ASSEMBLY MANUAL H2572IP-1 Features
Total solder points: 47 Difficulty level: beginner advanced METAL DETECTOR K7102 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 47 Difficulty level: beginner 1 2 3 4 5 advanced METAL DETECTOR K7102 Avoid disasters when drilling holes in walls... ILLUSTRATED ASSEMBLY MANUAL H7102IP Features & Specifications
K8066 3W MONO AMPLIFIER. Specifications
Total solder points: 34 Difficulty level: beginner 1 2 3 4 5 advanced 3W MONO AMPLIFIER K8066 Small but powerful amplifier suits a wide range of applications. Specifications Output power : 3Wrms (4-8 ohm,
Total solder points: Difficulty level: beginner advanced 0 TO 60 HOUR START / STOP TIMER K6200 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 96 + 43 Difficulty level: beginner 1 2 3 4 5 advanced 0 TO 60 HOUR START / STOP TIMER K6200 Broad range mains operated start / stop timer. ILLUSTRATED ASSEMBLY MANUAL H6200IP-1 VELLEMAN
Total solder points: 82 Difficulty level: beginner advanced. Dc to Pulse Width Modulator K8004 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 82 Difficulty level: beginner 1 2 3 4 5 advanced Dc to Pulse Width Modulator K8004 Allows very efficient control of DC motors, heaters or lights. ILLUSTRATED ASSEMBLY MANUAL H8004IP-2
K2601 STROBOSCOPE. Features
Total solder points: 38 Difficulty level: beginner 1 2 3 4 5 advanced STROBOSCOPE K2601 Great for party s, stage, photography,... Features Power supply : 220-240VAC Power consumption : 3-10W Flash frequency
Total solder points: 101 Difficulty level: beginner advanced ELECTRONIC WATCHDOG K2655 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 101 Difficulty level: beginner 1 2 3 4 5 advanced ELECTRONIC WATCHDOG K2655 Listens and scares intruders with realistic barking. ILLUSTRATED ASSEMBLY MANUAL H2655IP-2 Features & Specifications
Total solder points: 66 Difficulty level: beginner advanced. 15 Channel IR remote stick K8051 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 66 Difficulty level: beginner 1 2 3 4 5 advanced 15 Channel IR remote stick K8051 Sleek designer enclosure with just 2 buttons, yet it provides acces to a stunning 15 channels. ILLUSTRATED
Total solder points: 108 Difficulty level: beginner advanced PINK NOISE GENERATOR K4301 ILLUSTRATED ASSEMBLY MANUAL H4301IP-1
Total solder points: 108 Difficulty level: beginner 1 2 3 4 5 advanced PINK NOISE GENERATOR K4301 Add a spectrum analyser with a microphone and check your audio system performance. ILLUSTRATED ASSEMBLY
Total solder points: 79 Difficulty level: beginner advanced GUITAR PREAMPLIFIER WITH HEADPHONE OUTPUT K4102 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 79 Difficulty level: beginner 1 2 3 4 5 advanced GUITAR PREAMPLIFIER WITH HEADPHONE OUTPUT K4102 Practice the guitar without disturbing others. ILLUSTRATED ASSEMBLY MANUAL H4102IP-1
Eight channel remote relay card. Total solder points: 277 Difficulty level: beginner advanced K8056 ILLUSTRATED ASSEMBLY MANUAL
Eight channel remote relay card This relay card can be used in several ways : stand alone card, addressed by switches or open collector outputs or remote controlled through RS232. Total solder points:
Total solder points: 47 Difficulty level: beginner advanced METAL DETECTOR K7102 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 47 Difficulty level: beginner 1 2 3 4 5 advanced METAL DETECTOR K7102 Avoid disasters when drilling holes in walls... ILLUSTRATED ASSEMBLY MANUAL H7102IP Features & Specifications
400W MONO/STEREO AMPLIFIER
400W MONO/STEREO AMPLIFIER Universal, robust and compact are the words to describe this amplifier. Total solder points: 264 Difficulty level: beginner 1 2 3 4 5 advanced K4005B ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 271 Difficulty level: beginner advanced. 2 x 15 LED STEREO VU METER K4306 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 271 Difficulty level: beginner 1 2 3 4 5 advanced 2 x 15 LED STEREO VU METER K4306 For high precision audio level indication ILLUSTRATED ASSEMBLY MANUAL H4306IP-1 Features & Specifications
VOLUME AND TONE CONTROL - PREAMPLIFIER K8084
VOLUME AND TONE CONTROL - PREAMPLIFIER K8084 When using one of our amplifiers (big or small), you always need a volume control and preferably also a tone control H8084IP-1 Features & specifications When
K8055N. USB Experiment interface board. Interface your computer with the world using 5 digital in and 8 outputs, 2 analogue in-and outputs.
Total solder points: 313 Difficulty level: beginner 1 2 3 4 5 advanced USB Experiment interface board K8055N Interface your computer with the world using 5 digital in and 8 outputs, 2 analogue in-and outputs.
Power shield that can drive: relays, solenoids, DC and stepper motors
ILLUSTRATED KA0IP LUSTRA TED ASSEMBLY SE MANUAL AL HKA0IP Motor & Power shield Arduino Power shield that can drive: relays, solenoids, DC and stepper motors Features For use with Arduino Due, Arduino Uno,
K8039 DMX CONTROLLED POWER DIMMER. Control a lamp or group of lamps trough a DMX signal. Suitable for resistive and mains voltage halogen lighting.
DMX CONTROLLED POWER DIMMER K8039 Control a lamp or group of lamps trough a DMX signal. Suitable for resistive and mains voltage halogen lighting. Specifications control source: DMX-512, 3 pin XLR socket
Configure your Arduino as a simple web server or let it get data from the worldwide web.
KA0 ILLUSTRATED LUSTRA TED ASSEMBLY SE MANUAL HKA0IP KA0 Ethernet shield for Arduino Configure your Arduino as a simple web server or let it get data from the worldwide web. Features For use with Arduino
10W Class D Stereo Amplifier Kit
1 Total Solder Joints: 70 Difficulty Level : beginner expert 10W Class D Stereo Amplifier Kit PARADIGM Technologies (UK) Ltd Electronic Kits and Modules K1420 High power multipurpose audio amplifier Specifications
10W Class D Ultra Stereo Amplifier Kit
1 Total Solder Joints: 70 Difficulty Level : beginner expert PARADIGM Technologies (UK) Ltd Electronic Kits and Modules 10W Class D Ultra Stereo Amplifier Kit K1421 High power / quality audio amplifier
1A POWER SUPPLY K1823
Total solder points: 27 Skill level : 1 1A POWER SUPPLY K1823 Applications : Just add a suitable transformer (see table inside) Great to power your projects and save on batteries Use as adjustable power
K2655. Electronic watchdog. Features: Specifications :
Total solder points: 101 Difficulty level: beginner 1 2 3 4 5 advanced Features: Electronic watchdog K2655 Very realistic simulation through the use of a random generator. Choice of two different dogs.
πλ² Synthesizer Manual for Assembly Kit Features 2 Oscillators 4 Waveforms 32 Presets 32 User presets
πλ² Synthesizer Manual for Assembly Kit Features 2 Oscillators 4 Waveforms 32 Presets 32 User presets Specifications Power supply: +5V DC/50mA Dimensions: 100 x 100 x 23mm Congratulations on purchasing
Two channel codelock receiver
Total solder points: 224 Difficulty level: beginner 1 2 3 4 5 advanced Two channel codelock receiver K6727 Features: Easy to build: no coils to be made! Works together with the K6706/K6706A two channel
Read This Page First
Read This Page First If you are reading this you know the manuals are always available at QRPKITS.com. This is version 8.0 of the manual dated 4/27/2016. There is no need to print out the whole assembly
LITTLE NERD v1.1 Assembly Guide
last update: 9. 3. 2016 LITTLE NERD v1.1 Assembly Guide bastl instruments.com INTRODUCTION This guide is for building Little Nerd module from Bastl Instruments. It is good to have basic soldering skills
Pacific Antenna - Easy TR Switch
Pacific Antenna - Easy TR Switch Kit Description The Easy TR Switch is an RF sensing switch that can be used to switch an antenna between a receiver and transmitter. It also has a second switched pair
VC Divider Assembly manual
1 VC Divider Assembly manual Thank you for your purchase of the SSSR Labs VC Divider DIY Kit! This manual will help you assemble the VC Divider quickly and easily. Follow the instructions! As you may know,
LED Field Strength Indicator Kit
LED Field Strength Indicator Kit Description The Field Strength Indicator kit from Qrpkits.com provides a visual way to monitor RF fields through the brightness of an LED. It will respond to RF fields
Assembly Instructions
Assembly Instructions For the SSQ-2F 3.1 MHz Rife Controller Board Kit v1.41 Manual v1.00 2012 by Ralph Hartwell Spectrotek Services GENERAL ASSEMBLY INSTRUCTIONS Arrange for a clean work surface with
Pacific Antenna Easy TR Switch
Pacific Antenna Easy TR Switch Kit Description The Easy TR Switch is an RF sensing circuit with a double pole double throw relay that can be used to automatically switch an antenna between a separate receiver
Pacific Antenna Field Strength Indicator Kit
Pacific Antenna Field Strength Indicator Kit Description The Field Strength Indicator kit from Pacific Antenna provides a visual way to monitor the presence and relative strength RF fields through the
Line-Following Robot
1 Line-Following Robot Printed Circuit Board Assembly Jeffrey La Favre October 5, 2014 After you have learned to solder, you are ready to start the assembly of your robot. The assembly will be divided
LA502 Assembly guide Main PCB Resistors - (2)
LA502 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about
TKEY-1. CW touch key. (no electromechanical contacts) Assembly manual. Last update: May 1,
TKEY-1 CW touch key (no electromechanical contacts) Assembly manual Last update: May 1, 2016 ea3gcy@gmail.com Updates and news at: www.qsl.net/ea3gcy Thanks for constructing the TKEY-1A CW touch key Have
Pacific Antenna Easy SWR Indicator Kit
Pacific Antenna Easy SWR Indicator Kit Description Monitoring the match of an antenna to your transmitter or adjusting an antenna tuner for best match requires an indicator of the reflected power as an
Introduction 1. Download socket (the cable plugs in here so that the GENIE microcontroller can talk to the computer)
Introduction 1 Welcome to the magical world of GENIE! The project board is ideal when you want to add intelligence to other design or electronics projects. Simply wire up your inputs and outputs and away
Elektor Construction Guide TAPIR
Elektor Construction Guide TAPIR The TAPIR is a three-dimensional assembly. To ensure good access to all soldering points, we recommend assembling the kit exactly according to the described sequence. 1
CW-ADD. Universal CW Adapter for SSB Transceivers. Assembly manual. Last updated: October 1,
CW-ADD Universal CW Adapter for SSB Transceivers Assembly manual Last updated: October 1, 2017 ea3gcy@gmail.com Updates and news at: www.ea3gcy.com Thanks for building the Universal CW Adapter kit CW-ADD
3. Assembly manual ANALYZING THE PCB'S LCD PCB. Component side: Solder side:
3. Assembly manual ANALYZING THE PCB'S LCD PCB Component side: Solder side: MAIN PCB Component side: Solder side: ASSEMBLGING THE LCD PCB 1. Resistor R1: 33 Ohm (orange, black, black) 2. 6 Pin female header
Assembly and User Guide
Assembly and User Guide AtariPunkr is an adjustable stepped tone generator. AtariPunkr provides hours of fun everyone! Powered by: 9V Battery Outputs: Mylar Speaker (Included) Stereo Output (3.5mm Jack)
Building the Sawdust Regenerative Receiver
Building the Sawdust Regenerative Receiver Introduction The Sawdust is a super regenerative receiver using the basic Armstrong design architecture. The receiver uses one toroidal transformer to provide
Lighthouse Beginner s soldering kit
Lighthouse Beginner s soldering kit Kit contains: 1 x 220 ohm resistor (Red, Red, Black) 1 x 82k ohm resistor (Grey, Red, Orange) 2 x 220k ohm resistors (Red, Red, Yellow) 2 x Diodes 1 x Power switch 1
MICROGRANNY v2.1 - Assembly Guide
last update: 9. 5. 2017 MICROGRANNY v2.1 - Assembly Guide bastl-instruments.com INTRODUCTION Welcome to the assembly guide for the MicroGranny kit. MicroGranny is a monophonic granular sampler by Bastl
Value Location Qty Potentiometers C1M Distortion 1 A10k Volume 1. Footswitch 3PDT SW1 1. Jacks 1/4 Mono 2 DC Power 1
Distortion BUILD INSTRUCTIONS Thank you for your purchase of our Distortion+ kit! We have completely redesigned our entire line of kits to be the most user friendly, while still maintaining their same
LPF-9B Nine band low pass filter module kit ( meters)
LPF-9B Nine band low pass filter module kit (80-60-40-30-20-17-15-12-10 meters) Assembly manual Last update: March 1, 2018 ea3gcy@gmail.com Most recent updates and news at: www.ea3gcy.com Thanks for constructing
KN-Q10 Assembly Manual
KN-Q10 Assembly Manual Translated by Adam Rong, BD6CR/4 with permission from Ke Shi, BA6BF Edited by Stephen, VK2RH Revision B, Oct 14, 2010 Thank you for purchasing the KN-Q10 4 Band SSB/CW Dual Mode
Easy Transmitter. Support ETX_REV5_Manual V2.7 Revised
Easy Transmitter Introduction The Easy Transmitter kit from qrpkits.com provides a basic, crystal controlled transmitter with VXO tuning to provide a small tuning range around the crystal frequency. It
BP-1A. Band-Pass variable filter continuous tuning from 3 to 30MHz. For analogue or software-defined receivers (SDR) Assembly manual
BP-1A Band-Pass variable filter continuous tuning from 3 to 30MHz. For analogue or software-defined receivers (SDR) Assembly manual Last updated: December 1, 2017 ea3gcy@gmail.com Updates and news at:
Pacific Antenna Low Pass Filter Kit
Pacific Antenna Low Pass Filter Kit Description Many basic transmitter and/or transceiver designs have minimal filtering on their output and frequently have significant harmonic content in their signals.
12V Dimmer Kit, version 2
12V Dimmer Kit, version 2 User Manual Description The 12V Dimmer Kit V2 is an especially efficient PWM (pulse-width modulation) controller for 12V loads up to 60 watts. It features a single dial control
Technical Specifications - Characteristics
Watt FM TRANSMITTER General Description This is a small but quite powerful FM transmitter having three RF stages incorporating an audio preamplifier for better modulation. t has an output power of 4 Watts
The Walford Electronics Ford Receiver Kit Project Construction Manual
The Walford Electronics Ford Receiver Kit Project Construction Manual Walford Electronics Ford Receiver construction manual V1.5 Page 1 of 22 Introduction The Ford receiver has four stages: The first stage
TS500 Assembly guide. Soldering. TS500 Assembly guide Main PCB 1. Diodes. Document revision 1.2 Last modification : 17/12/16
TS500 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about
Building the Toothpick Audio CW Filter
Building the Toothpick Audio CW Filter Introduction The toothpick is a simple variable bandpass audio filter designed to compliment the Splinter QRPp Trans-Receiver. The filter also contains an audio amplifier
Xkitz.com XLO-5CP Control Panel for Five Channel Color Light Organ
Xkitz.com XLO-5CP Control Panel for Five Channel Color Light Organ Rev 1.15 An Optional accessory for the Xkitz XLO-5 or XLO-5DC 5 Channel Color Light Organs Introduction This kit contains all the electronics
Building the Sawdust Regenerative Receiver
Building the Sawdust Regenerative Receiver Introduction The Sawdust is a super regenerative receiver using the basic Armstrong design architecture. The receiver uses one toroidal transformer to provide
Pacific Antenna Easy Transmitter Kit
Pacific Antenna Easy Transmitter Kit Introduction The Easy Transmitter kit from qrpkits.com provides a crystal controlled transmitter with VXO tuning. The circuit consists of a N3904 based crystal oscillator
Bill of Materials: Metronome Kit PART NO
Metronome Kit PART NO. 2168325 The metronome kit allows you to build your own working electronic metronome. Features include a small speaker, flashing LED, and the ability to switch between several different
The ability to make basic voltage and resistance measurements using a digital multimeter
Congratulations on your purchase of a new OneShot chassis! The PC01 OneShot combines a rugged enclosure, power supply, and discrete instrument DI in a compact 1/4U package. A few minutes of assembly are
ABC V1.0 ASSEMBLY IMPORTANT!
ABC V1.0 ASSEMBLY Before starting this kit, prepare the following tools: Soldering iron (15-20W will do), flush cutters, no.2 hex screwdriver or allen key and phillips screwdriver. Also briefly go through
Assembly Instructions for the 1.5 Watt Amplifier Kit
Assembly Instructions for the 1.5 Watt Amplifier Kit 1.) All of the small parts are attached to a sheet of paper indicating both their value and id. 2.) Leave the parts affixed to the paper until you are
Circuit Board Assembly Instructions for Babuinobot 1.0
Circuit Board Assembly Instructions for Babuinobot 1.0 Brett Nelson January 2010 1 Features Sensor4 input Sensor3 input Sensor2 input 5v power bus Sensor1 input Do not exceed 5v Ground power bus Programming
Guitarpedalkits.com Overdrive Pedal Build Instructions
Page 1 Guitarpedalkits.com Overdrive Pedal Build Instructions Follow the instructions in this guide to build your very own DIY overdrive pedal from GuitarPedalKits.com. If you re a first time builder,
Read This Page First
Read This Page First If you are reading this you know the manuals are always available at QRPKITS.com. If you have questions contact qrpkits.com@gmail.com There is no need to print out the whole assembly
Modifying a USB sound fob to act as a repeater interface for app_rpt
Modifying a USB sound fob to act as a repeater interface for app_rpt This document explains how to modify a USB sound fob to work as a repeater interface for app_rpt. The following materials and tools
TekBot Remote Control Receiver Board Construction
TekBot Remote Control Receiver Board Construction Purpose This tutorial illustrates the procedure for construction of the Receiver board for the TekBot. A Guide to Soldering Many of you have soldered once
Value Location Qty Transistors 2N5485 Q1, Q2, 4 Q3, Q4 2N5087 Q5 1. Trim Pots 250k VTRIM 1. Potentiometers C500k Speed 1. Toggle Switch On/On Vibe 1
P-90 BUILD INSTRUCTIONS Thank you for your purchase of our P-90 kit! We have completely redesigned our entire line of kits to be the most user friendly, while still maintaining their same great sound!
Soldering Techniques NIAGARA COLLEGE TECHNOLOGY DEPT.
Soldering Techniques NIAGARA COLLEGE TECHNOLOGY DEPT. Soldering 101 Soldering is the process of joining two metals together to form an electrically ll and mechanically secure bond using heat and a third
DC Motor. Controller. User Guide V0210
DC Motor Controller User Guide 59757 V0210 This kit provides a great exercise of intermediate soldering skills and creates a device that enables you to control various Pitsco motors, Tamiya gearboxes,
Read This Page First
Pacific Antenna 0 Watt HF Amplifier Kit Manual This is Version 5.5 dated 060505 Read This Page First If you are reading this you know the manuals are always available at QRPKITS.com. If you have questions
Assembly Instructions for B7971 Smart Socket
Assembly Instructions for B7971 Smart Socket Identification and installation of the resistors, Fig1 Segment 1,R1, 22k Segment 4, R4, 22k Segment 2, R2, 27k Segment 3, R3, 27k Segment 5, R5, 27k Segment
Telecaster Wiring Kits Please Read All Instructions Before Beginning. Tools you will need: Soldering tips: Removing Current Wiring: Step 1. Step 2.
Telecaster Wiring Kits Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers Wire Strippers 3/8 Drill Bit 5/32 Drill Bit
Gat ew ay T o S pace AS EN / AS TR Class # 07. Colorado S pace Grant Consortium
Gat ew ay T o S pace AS EN / AS TR 2500 Class # 07 Colorado S pace Grant Consortium One Minute Reports: - Can we have two data loggers? - Do you provide us with cameras? {Hardware Checkout after proposal}
DDDAC1794. Version 1.1
Finally!! The new, highly improved 2016 module! De voltage regulation at the analog side of the system has now an embedded Tentlabs Shunt regulator. The Bias through the much discussed pin 20 got a constant
Pacific Antenna 10 Watt HF Amplifier Kit
Pacific Antenna 0 Watt HF Amplifier Kit Description Our 0 watt Linear, HF amplifier kit is designed to increase the power output of low power transmitters. Gives up to 5dB gain and includes an input attenuator
THE RING RESONATOR (K-975)
THE RING RESONATOR (K-975) OUTPUT BOOST The Ring Resonator An Octave Up Fuzz Modkitsdiy.com 9 VDC CENTER (-) ADAPTER TO AMP IN FROM GUITAR OUT Unplug when not in use to save battery life. Use these instructions
Electronics Merit Badge Class 4. 12/30/2010 Electronics Merit Badge Class 4 1
Electronics Merit Badge Class 4 12/30/2010 Electronics Merit Badge Class 4 1 Soldering Safety Note: A Soldering Iron gets hotter than 374 F. Do not touch the soldering iron s metal parts or you will receive
THE THUNDERDRIVE (K-950)
THE THUNDERDRIVE (K-950) OUTPUT DISTORTION Unplug when not in use to save battery life. TO AMP IN The Thunderdrive Modkitsdiy.com FROM GUITAR OUT Use these instructions to learn: How to build an effects
Assembly Instructions
Assembly Instructions for the PA3 v2.0 Amplifier Kit PA3 Amplifier shown mounted on HS2 Heat Sink (The HS2 shown here is not included with this kit.) 27 February 2016 2013-2016 by Ralph Hartwell Spectrotek
Pacific Antenna Code Practice Oscillator Kit
Pacific Antenna Code Practice Oscillator Kit This kit is offered to initiate the first time builder in the various techniques of mechanical and electronic kit construction. At the end of the approximately
KLIK v1.0 - Assembly Guide
last update: 12. 7. 2017 KLIK v1.0 - Assembly Guide bastl-instruments.com INTRODUCTION Welcome to the assembly guide for the KLIK by BASTL INSTRUMENTS. Klik is a synchronisation device that enables you
Cricket 80a Assembly Manual v Copyright David Cripe NM0S The 4 State QRP Group
Cricket 80a Assembly Manual v. 1.0 Copyright 2017 David Cripe NM0S The 4 State QRP Group Introduction Thank you for purchasing a CRICKET 80a Transceiver. We hope you will enjoy building it and find it
RF Current Meter Kit
Kit When assembled, this kit provides you with a simple but effective means of measuring the current in antenna wires, and of looking for braid currents on coax feeders. The more current you can get flowing
KASTLE v1.5 - Assembly Guide
last update: 14. 12. 2017 KASTLE v1.5 - Assembly Guide bastl-instruments.com INTRODUCTION Welcome to the assembly guide for the Kastle kit - mini modular synthesizer. It is suitable for beginners. It is
K Input programmable messageboard with LCD & serial interface. Features : Specifications :
Total solder points: 239 Difficulty level: beginner 2 3 4 5 advanced 8 Input programmable messageboard with LCD & serial interface Features : K8045 Add an LCD display to any low-tech application and make
Ten Tec DDS Board Assembly Procedure
05 May 2014 Ten Tec DDS Board Assembly Procedure You will find a photo of a completed board at the end of these instructions. Refer it whenever clarification is required. 1. AD9835 Attachment If you purchased
Tek-Bot Remote Control Transmitter Board Construction
Tek-Bot Remote Control Transmitter Board Construction Purpose This tutorial illustrates the procedure for construction of the Transmitter board for the Tek-bot. A Guide to Soldering Many of you have soldered
DuoDrive Nixie Bargraph Kit
Assembly Instructions And User Guide Nixie Bargraph Kit - 1 - REVISION HISTORY Issue Date Reason for Issue Number 1 12 December 2017 New document - 2 - 1. INTRODUCTION 1.1 About Nixie Bargraph Driver IN-9
Explorer Wiring Kit (assembled)
Explorer Wiring Kit (assembled) For Vintage, Firestorm & Standard Series Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers
Find a place where you can work through completion, without disturbing your
Scan by Manual Manor ARIES SYSTEM 300 MUSIC SYNTHESIZER Page I of 4 MODULE AR-334 SEQUENCER ASSEMBLY INSTRUCTIONS It is recommended that you do the following before you proceed: Find a place where you