Total solder points: 101 Difficulty level: beginner advanced ELECTRONIC WATCHDOG K2655 ILLUSTRATED ASSEMBLY MANUAL

Transcription

1 Total solder points: 101 Difficulty level: beginner advanced ELECTRONIC WATCHDOG K2655 Listens and scares intruders with realistic barking. ILLUSTRATED ASSEMBLY MANUAL H2655IP-2

2 Features & Specifications Features: Very realistic simulation through the use of a random generator. Choice of two different dogs. Reacts to environment noise, with adjustable sensitivity. Trigger input to connect other detectors (photo-electric cell, motion detector, smoke detector, etc...). Connectable to more powerful amplifier. Complete with rectifier and voltage regulator. Specifications: Power supply : 2x8V/0,5A transformer or 9 to 12VDC. Loudspeaker output (2W at 4 ohm). Supply current: standby: 75mA, when barking: max. 400mA. Dimensions: 142x75x30mm / (5,7x3x1,2"). 2

3 Assembly hints 1. Assembly (Skipping this can lead to troubles! ) Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully. 1.1 Make sure you have the right tools: A good quality soldering iron (25-40W) with a small tip. Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called thinning and will protect the tip, and enables you to make good connections. When solder rolls off the tip, it needs cleaning. Thin raisin-core solder. Do not use any flux or grease. A diagonal cutter to trim excess wires. To avoid injury when cutting excess leads, hold the lead so they cannot fly towards the eyes. Needle nose pliers, for bending leads, or to hold components in place. Small blade and Phillips screwdrivers. A basic range is fine. For some projects, a basic multi-meter is required, or might be handy Assembly Hints : Make sure the skill level matches your experience, to avoid disappointments. Follow the instructions carefully. Read and understand the entire step before you perform each operation. Perform the assembly in the correct order as stated in this manual Position all parts on the PCB (Printed Circuit Board) as shown on the drawings. Values on the circuit diagram are subject to changes. Values in this assembly guide are correct* Use the check-boxes to mark your progress. Please read the included information on safety and customer service * Typographical inaccuracies excluded. Always look for possible last minute manual updates, indicated as NOTE on a separate leaflet. 3

4 Assembly hints 1.3 Soldering Hints : 1- Mount the component against the PCB surface and carefully solder the leads 2- Make sure the solder joints are cone-shaped and shiny 3- Trim excess leads as close as possible to the solder joint AXIAL COMPONENTS ARE TAPED IN THE CORRECT MOUNTING SEQUENCE! REMOVE THEM FROM THE TAPE ONE AT A TIME! You will find the colour code for the resistances and the LEDs in the HALG (general manual) and on our website: 4

5 Construction 1. Jumpers J1 J3 J6 2. Diodes. Watch the polarity! D1 : 1N4148 D2 : 1N4148 D3 : 1N4148 D4 : 1N4148 D5 : 1N4148 D6 : 1N4007 D7 : 1N4007 CATHODE D Resistors R... R1 : 330 ( B) R2 : 10K ( B) R3 : 10K ( B) R4 : 10K ( B) R5 : 10K ( B) R6 : 220K ( B) R7 : 1K ( B) R8 : 1K ( B) R9 : 1K ( B) R10 : 4K7 ( B) R11 : 4K7 ( B) R12 : 4K7 ( B) R13 : 4K7 ( B) R14 : 47K ( B) R15 : 47K ( B) R16 : 47K ( B) R17 : 47K ( B) R18 : 220K ( B) R19 : 10 ( B) R20 : 2M2 ( B) R21 : 10K ( B) R22 : 2K7 ( B) R23 : 2K7 ( B) R24 : 2K7 ( B) R25 : 2K7 ( B) R26 : 2K7 ( B) R27 : 2K7 ( B) R28 : 2K7 ( B) R29 : 2K7 ( B) 4. Metal film resistors R... R30 : 100K ( ) R31 : 100K ( ) R32 : 100K ( ) R33 : 100K ( ) R34 : 100K ( ) 5

6 Construction R35 : 100K ( ) R36 : 100K ( ) R37 : 100K ( ) R38 : 100K ( ) R39 : 51K ( ) ( ) R40 : 51K ( ) ( ) R41 : 51K ( ) ( ) R42 : 51K ( ) ( ) R43 : 51K ( ) ( ) R44 : 51K ( ) ( ) R45 : 51K ( ) ( ) 5. IC sockets. Watch the position of the notch! IC1 : 14p IC2 : 14p IC3 : 16p IC4 : 28p IC5 : 16p IC6 : 14p IC7 : 8p 6. Capacitors. C1 : 100pF (101) C2 : 10nF (103) C3 : 10nF (103) C4 : 3,9nF (392) C5 : 47nF (473) C6 : 47nF (473) C9 : 100nF (104) C10 : 100nF (104) C11 : 100nF (104) C Resistor trimmers RV2 : 2M2 Time RV3 : 100K Tone 8. Transistors T1 : BC547 T2 : BC PCB tabs. A GND B VAC TRIG MIC LS RV1 6

7 Construction 10. Capacitors 12. Big trimmers. RV IC s. Watch the position of the notch! C7 : 100nF / 250V C8 : 100nF / 250V 11. Electrolytic Capacitors. Watch the polarity! C... RV1 : 4K7 TRIG level RV4 : 470K Volume 13. Voltage regulator VR... IC1 : LM324 or eq. IC2 : CD4093 or eq. IC3 : CD4040 or eq. IC4 : VK2655 (programmed Eprom 2764C25) IC5 : CD4015 or eq. IC6 : CD4077 or eq. IC7 : LM386 or eq. C12 : 10µF / 35V C13 : 10µF / 35V C14 : 220µF / 16V C15 : 1000µF / 16V VR1 : UA7805 7

8 Construction 15. Microphone MIC... MIC Attention : the negative connection is the one closest to the earth lip of the microphone housing. Solder them both together. The remaining pin is the positive connection. Twist the connection wires in order to avoid interferences and noise. Tip : use screened cable (Screen connected to the negative should the connection be too long (0,5m or 2ft). 8

9 Connecting 16. CONNECTING 1. Hook up when using a transformer Min. 4 ohm Red Black B GND A 2x8V/0.5A Fig

10 Connecting 2. Hook when using a battery : Min. 4 ohm Red Black 9V battery Red Black Fig

11 Test & use 17. TEST & USE Turn all the trimmers to their centre position. Connect a loudspeaker of at least 4 ohm to the points LS. Connect the transformer (8V-0-8V) to the points VAC (Fig. 1.0). The center tap (0) should be connected to ground (GND, the middle one of the three VAC pins). The circuit can also be powered with direct current (9 to 12V, unregulated): in this case the negative goes to GND (the middle pin), the positive to one of the two outmost pins A or B (Fig. 2.0) Make some noise, your loyal servant will promptly start barking. With RV1 (TRIG LEVEL) you can adjust the sensitivity of the detector. In case the circuit is too sensitive you may replace R20 by a 1M (brown, black, green, gold) or 470K (yellow, violet, yellow, gold). RV4 is the volume potentiometer. With RV3 you can adjust the pitch of the barking. Remove J1 and install J2 to select the other dog. After each triggering, the circuit continues barking for a while. With RV2 you can adjust that period. The circuit can also be triggered by other detectors if you like: to make the dog bark, you only have to shortcircuit the TRIG points with a relay contact, push-button, etc... 11

12 Test & use Capacitor C3 takes care that the dog does not go on barking as long as the TRIG contacts are closed. To enable barking the whole time (e.g. with smoke detection), you may replace capacitor C3 by a wire link. With a 4 ohm horn-type loudspeaker, the volume usually will appear sufficient. Should you still want a more powerful amplifier, you may connect it to AF OUT. Pay attention to the polarity! Fit a 100nF MKM capacitor for C16. If you are sure that the power amplifier already has a capacitor at the input, then you may fit a wire link for C16. 12

13 PCB 18. PCB layout. 13

14 Diagram 19. Diagram 14

15 Diagram 15

16 Modifications and typographical errors reserved Velleman nv. H2655IP ED3 VELLEMAN NV Legen Heirweg 33, 9890 Gavere Belgium - Europe