An onboard regulator permits with supply voltages of 2.5V to 24V which makes the device suitable for a wide range of industrial applications

Size: px

Start display at page:

Download "An onboard regulator permits with supply voltages of 2.5V to 24V which makes the device suitable for a wide range of industrial applications"

Leo Phelps
5 years ago
Views:

1 Description device is a chopper-stabilized Hall Effect ensor that offers a magnetic sensing solution with superior sensitivity stability over temperature and integrated protection features. uperior high-temperature performance is made possible through dynamic offset cancellation, which reduces the residual offset voltage normally caused by device over molding, temperature dependencies, and thermal stress. Each device includes on a single silicon chip a voltage regulator, Hall-voltage generator, small-signal amplifier, chopper stabilization, chmitt trigger, and a open-collector output to sink up to 20mA. The output turns low with the magnetic outh Pole on the branded side of the package and turns high if the magnetic field is removed (for UA package). An onboard regulator permits with supply voltages of 2.5V to 24V which makes the device suitable for a wide range of industrial applications Features Digital Unipolar Hall ensor upports a wide voltage range (2.5 to 24V) Resistant to physical stress Wide operating temperature range High chopping frequency olid-state reliability High sensitivity (B OP and B RP ) mall package sizes Output state Terminal configuration and functions Terminal ame umber TYPE DECRIPTIO UA O VDD 1 1 PWR 2.5V to 24 V power supply GD 2 3 Ground Ground terminal OUT 3 2 Output Open-drain output. The open drain requires a pull-up resistor

2 Absolute Maximum Ratings over operating free-air temperature range MI MAX UIT Power supply voltage VDD V Output terminal voltage OUT V Output terminal current sink I IK 0 30 ma Operating junction temperature, T J Tstg V ED Electrical Characteristics HBM ED stress voltage kv MM ED stress voltage V over operating free-air temperature range (unless otherwise noted) PARAMETER TET CODITIO MI TYP MAX UIT V DD Operating voltage V I DD Operating supply current V DD =2.5V to 24 V ma t on Power-on time µ I lkg Off-state leakage current Output Hi-Z µa r D(on) FET on-resistance V DD =5V, I O =10mA, T A = Ω t d Output delay time B=0Gs to B OP + 100Gs µ t r Output rise time R1=1Kohm Co=50pF µ t f Output fall time R1=1Kohm Co=50pF µ Magnetic Characteristics f BW Bandwidth khz B OP Operated point Gs B RP B HY Release point UA Package Gs Hysteresis Gs B OP Operated point Gs B RP B HY Release point OT23 Package Gs Hysteresis Gs B OP Operated point Gs B RP Release point OT23-3 Package Gs B HY Hysteresis Gs Function Description Overview The device is a chopper-stabilized Hall sensor with a digital latched output for

3 magnetic sensing applications. The output of the device switches low (turns on) when a magnetic field perpendicular to the Hall element exceeds the operate point threshold, B OP. After turn-on, the output voltage is V OUT(sat). The output transistor is capable of sinking current up to 20mA. When the magnetic field is reduced below the release point, B RP, the device output goes high (turns off). The difference in the magnetic operate and release points is the hysteresis, B HY, of the device. This built-in hysteresis allows clean switching of the output even in the presence of external mechanical vibration and electrical noise. Functional Block Diagram VC C C 1 R egulated upply R 1 Bias Temperature C ompensation OUT C 2 Hall E lement Offset C ancelation G ate DR V R eference G D

4 Field Direction Definition A positive magnetic field is defined as a south pole near the marked side of the package. TO-92 Package OUT=Low OUT=High UA Package UA Package OT23-3 Package OUT=Low OUT=High O Package O Package OT23 Package

5 If the device is powered on with a magnetic field strength between B RP and B OP, then the device output is determinate High. For UA package, if the field strength is greater than B OP, then the output is pulled low. If the field strength is less than B RP, the output is released. For O package, however, if the field strength is less than B OP, then the output is pulled low. If the field strength is greater than B RP, the output is released. Package Designator (UA) 3-Terminal UA P ackage Dimension:mm MAX otes: 1. E xact body and lead configuration at vendor s option within limits shown. 2. Height does not include mold gate flash. Where no tolerance is specified, dimension is nominal.

6 Package Designator (OT23-3) 3-Terminal O P ackage D imens ion:mm ± ± ± ± ± ± ± ± ±0.1 otes: 1. E xact body and lead configuration at vendor s option within limits s hown. 2. Height does not include mold gate flas h. Where no tolerance is specified, dimension is nominal.

7 Package Designator (OT23)

3185 THRU 3189 HALL-EFFECT LATCHES FOR HIGH-TEMPERATURE OPERATION FEATURES. ABSOLUTE MAXIMUM RATINGS at T A = +25 C V CC GROUND OUTPUT SUPPLY

3185 THRU 3189 HALL-EFFECT LATCHES FOR HIGH-TEMPERATURE OPERATION FEATURES. ABSOLUTE MAXIMUM RATINGS at T A = +25 C V CC GROUND OUTPUT SUPPLY 3185 THRU 3189 Data Sheet 2769.2A X V CC These Hall-effect latches are extremely temperature-stable and stressresistant sensors especially suited for operation over extended temperature ranges to +15 C.