4. Set the FLSER tool switch to the S-RID position. 5. Push the + and - buttons to select the sensor ID (SID) for the transmitter.
|
|
- Meryl Glenn
- 5 years ago
- Views:
Transcription
1 V2.2 ( ) 1 (8) COISSIONING Selecting the transmitter position The device can be installed in dry surroundings (I20) by screws on the wall surface or on the standard flush mounting box. The recommended installation height is cm. The device position should be selected carefully. All the error factors that can affect to the measurements should be eliminated as well as possible. The following list defines the typical measurement error factors. Wiring direct sun light occupant proximity air flow coming from windows or doors air flow coming from ventilation nozzles air flow coming from the flush mounting box differential temperature caused by external wall NOTE: The wireless network coverage affects also on the transmitter positioning. With the help of FLSER commissioning tool, you can see the wireless network coverage and select the ideal transmitter positions inside the network. Device wiring and commissioning can only be carried out by qualified professionals. Always make the wirings while the power is switched off. NOTE: measurement causes a current peak to the supply voltage. This can produce an error to the analogue outputs when using long and thin cables. It is recommended to increase the wire cross section area in long cable situations (e.g. by using free pairs) to ensure reliable measurement signal. Connecting to wireless network IORTANT: The device wireless network settings are made by using either FLSER or L-SER commissioning tool. When the wireless settings are made with one tool, the other tool cannot be used to change or check the wireless settings. Connecting to wireless network by using FLSER tool 1. Disconnect the transmitter power supply. 2. Set the FLSER tool switch to the ID position. 3. ush the + and - buttons to select the FLTA base station master ID (ID) to which you are connecting the transmitter. 6 ID= 4. Set the FLSER tool switch to the S-RID position. 5. ush the + and - buttons to select the sensor ID (SID) for the transmitter. 8 SID= 6. ush the button. Wait message starts to flash on the FLSER tool display. You have now approximately 30 seconds to complete the next step.
2 2 (8) 7. Connect the power supply. flashes on the FLSER display. When the flashing stops, the transmitter is ready to start the communication with the FLTA base station. 8. FLSER tool starts to display the communication signal strengths between the FLSER and transmitter. 8 RSSI 9 The bigger number indicates the strength of the received signal sent by FLSER and the smaller number the strength of received signal sent by the transmitter. RSSI = Received Signal Strength Indication: 1 2 = poor 3 5 = satisfactory 6 9 = good 10. Go to the FLTA base station and check that the signal strengths are adequate. 11. Set the FLSER tool switch to the OFF position. The transmitter starts to communicate with the FLTA base station. Reading the transmitter information from FLTA base station The transmitter information can be read from the FLTA base station in three ways: From the display 6 TE C LUX RH% Temperature level Humidity (only in RH models) Through the analogue outputs Via odbus INDICATOR LIGHT FUNCTIONS A. Green indicator light B. Red indicator light The indicator lights are on for 0.5 seconds during the device start-up. The green indicator light flashes when the device sends information to the base station. The red indicator light turns on when the message transmit to the base station fails 20 consecutive times.
3 3 (8) L-SER TOOL With the L-SER tool you can change the device settings, controller and wireless network settings for example. Connecting L-SER tool to the device 1. Remove the display / HD-AL3 option. 2. Connect the L-SER cable to the connector. A. L-SER cable measurement value shows on the L-SER tool display.
4 4 (8) L-SER L-SER opens by pressing the button. The values can be changed with the + and - buttons. The is device-specific and the content depends on the device and installed options. The following structure contains the factory settings. easurement Wireless settings 900 WIRELESS CO2ppm OFF SENSOR ID odbus 1 ID ASTER ID aster ID (ID) [1 63] Sensor ID (SID) [OFF / 1 99] Calibration CALIBRATION odbus 0 ID Offset: CO2ppm tuning [±200 ppm] On ABC-Logic ABCLogic calibration [On / Off] 0.0 Offset: C Temperature measurement tuning [±3,0 C] 0 Offset: %RH Humidity measurement tuning [±5 %RH] OFF roller CONTROLLER CO2 odbus I ID 700 CO2 Setpoint rol method Integration time set point [ ppm] 0 CO2 ropor. band proportional band [ ] TEERATURE odbus I ID C Setpoint rol method Integration time C set point [ C] 2.0 C ropor. band C proportional band [1,0...32,0] HUIDITY odbus I ID %RH Setpoint rol method Integration time %RH set point [ %] %RH ropor. band %RH proportional band [ ] AXIU CTR L I odbus ID 700 CO2 Setpoint rol method Integration time set point [ ppm] 0 CO2 ropor. band proportional band [ ] C Setpoint C set point [ C] 2.0 C ropor. band C proportional band [1,0...32,0] %RH Setpoint %RH set point [ %] %RH ropor. band %RH proportional band [ ] AL3 Info AL3 INFO 7 12 YELLOW RED Yellow indicator light illumination point [ ppm] odbus ID VERSION Software version 5 s Red indicator light illumination point [ ppm] no RESET Reset to factory settings [no / yes]
5 5 (8) Wireless settings WIRELESS odbus 1 ID 1 ASTER ID SENSOR ID aster ID (ID) [1 63] Sensor ID (SID) [OFF / 1 99] Through the wireless settings you can set the master ID and sensor ID. IORTANT: The device wireless network settings are made by using either FLSER or L-SER commissioning tool. When the wireless settings are made with one tool, the other tool cannot be used to change or check the wireless settings. Calibration CALIBRATION odbus 0 ID Offset: CO2ppm tuning [±200 ppm] On 0.0 ABC-Logic Offset: C ABCLogic calibration [On / Off] Temperature measurement tuning [±3,0 C] 0 Offset: %RH Humidity measurement tuning [±5 %RH] All the measurements can be tuned through the calibration. The humidity tuning is available only in RH models. The value can be adjusted by 10 ppm steps. The temperature value can be adjusted by 0.1 C steps. The humidity value can be adjusted by 1 % steps. L-SER tool display shows how much the current value is tuned.
6 6 (8) roller OFF CONTROLLER CO2 odbus I ID 700 CO2 Setpoint rol method Integration time set point [ ppm] 0 CO2 ropor. band proportional band [ ] TEERATURE odbus I ID C Setpoint rol method Integration time C set point [ C] 2.0 C ropor. band C proportional band [ ] HUIDITY odbus I ID %RH Setpoint rol method Integration time %RH set point [ %] %RH ropor. band %RH proportional band [ ] AXIU CTRL odbus I ID 700 CO2 Setpoint rol method Integration time set point [ ppm] 0 CO2 ropor. band proportional band [ ] C Setpoint C set point [ C] 2.0 C ropor. band C proportional band [ ] %RH Setpoint %RH set point [ %] %RH ropor. band %RH proportional band [ ] The control output can be controlled either according to a one measurement value or according to the maximum selection of all values. Humidity related settings are only available in RH models. The values can be adjusted by 10 ppm steps. The temperature values can be adjusted by 0,1 C steps. The humidity values can be adjusted by 5 % steps.
7 In the maximum selection control, the control output signal is formed according to the measurement that causes the largest control signal value. The following situation is in the example figure: Carbon dioxide concentration is 800 ppm Temperature is 21,5 C Humidity is 55 % 7 (8) AL3 AL YELLOW RED Yellow indicator light illumination point [ ppm] Red indicator light illumination point [ ppm] AL3 is available if HD-AL3 option is installed. The indicator light limits can be changed through the. The hysteresis is ppm. Info INFO odbus ID VERSION Software version 5 s no RESET? Reset to factory settings [no / yes] You can check the device software version and reset the device to factory settings through the Info. NOTE: If the wireless settings are set with the FLSER tool, resetting the factory settings doesn't return the wireless settings to the factory defaults.
8 8 (8) SELECTING THE EASUREENT INFORATION TO BE VIEWED ON THE DISLAY The measurement values scroll on the N model display. The wanted value can be locked to view continuously by pressing the S1 button. You resume to the scrolling view by pressing the S1 button again. CALIBRATION A. S1 button If ABCLogic method is not in use, the device should be calibrated every 6-12 months. The recommended calibration interval is 5 years even if the ABCLogic is in use. ABCLOGIC T self-calibration feature ABCLogic (Automatic Background Calibration Logic) is a patented self-calibration technique. ABCLogic method eliminates the possible long term drift. ABCLogic method can be used when the concentration drops at least two times within a week to the level of approx. 400 ppm. Therefore the ABCLogic is effective in spaces that are not continuously occupied. ABCLogic can be deactivated in continuously occupied spaces. Deactivating the ABCLogic The ABCLogic function can be deactivated by using the L-SER tool.
A. S1 button NOTE: In M models, the shown measurement information can be selected also via Modbus.
V1.0.0 (20.02.201) 1 (10) OUNTING The device can be installed in dry surroundings (I20) by screws on the wall surface or on the standard flush mounting box. The recommended installation height is 1 180
More informationWIRELESS BASE STATION WIRELESS CONFIGURATION TOOL WIRELESS REPEATER
WIRELESS BASE STATION FLTA is a base station for wireless network transmitters and I/O modules. From FLTA, the controls and measurements can be read via Modbus RTU and through the analogue outputs. Respectively
More informationAir Quality Sensor KNX AQS
Air Quality Sensor KNX AQS Installation and Adjustment 1 Content 1. Description... 3 1.0.1. Measurement of carbon dioxide in the air... 3 1.1. Technical specifications... 4 2. Installation and commissioning...
More informationWireless CO 2. + TRH Sensor. Installation Guide. Version 1
Wireless CO 2 + TRH Sensor Installation Guide Version 1 2 CO2 + TRH Sensor Installation Guide Introduction The wireless CO 2 + TRH (Carbon Dioxide + Temperature and Relative Humidity) sensor is a wall
More information200 RTH OFF ON IN OUT ALARM RESET
200 RTH OFF ON IN OUT ALARM RESET EN OWNER S MANU AL www.auraton.pl 2 3 Thank you for purchasing the modern temperature controller based on an advanced microprocessor. AURATON 200 RTH LCD FrostGuard function:
More informationCDG. Carbon Dioxide - User Manual Gas Detector. 1 Intended Use. 2 Functional Description. 3 Installation. 4 Electrical Connection.
Carbon Dioxide - User Manual 1 Intended Use 2 Functional Description 2.1 Control Mode 2.2 Sensor 3 Installation 3.1 Mounting instructions 3.2 Installation 4 Electrical Connection 4.1 Instruction 5 Commissioning
More informationWIRELESS TRANSMITTERS... 1 PRODUCT SELECTION GUIDES...
CONTENTS WIRELESS TRANSMITTERS... 1 PRODUCT SELECTION GUIDES... 9 sensor characteristics... 9 sensor selection guide...10 WIRELESS TRANSMITTERS Our wireless transmitters have a proven and field tested
More informationUser Manual. tsense VAV Disp. CO 2 -, temperature- and relative humidity transmitter
User Manual tsense VAV Disp CO 2 -, temperature- and relative humidity transmitter General tsense VAV for wall mounting measures indoor air carbon dioxide concentration, temperature and relative humidity
More informationTS-WS-07 Wireless Indoor/Outdoor 8-Channel Thermo-Hygrometer with Jumbo Display User Manual
TS-WS-07 Wireless Indoor/Outdoor 8-Channel Thermo-Hygrometer with Jumbo Display User Manual Table of Contents 1. Introduction......2 2.Getting Started.....2 2.1 Parts List.......2 2.2 Recommend Tools.........2
More informationINTAC Microprocessor Humidifier Controller
PURE Humidifier Company Read and Save These Instructions INTAC Microprocessor Humidifier Controller Installation Instructions Operation and Maintenance Manual 002 % Power 68% Heaters 1 2 3 4 INTAC Humidifier
More informationAURATON 2020 AURATON 2020 TX RX Plus
0 I 31 EN AURATON 2020, AURATON 2020 TX RX Plus AURATON 2020 AURATON 2020 AURATON 2020 TX RX Plus Preliminary notes The manual includes the information on AURATON 2020 and AURATON 2020 TX RX Plus controllers.
More informationInstruction Manual T5140 T5141 T5145 T5240 T5241 T5245. Programmable transmitter of CO2 concentration with 4-20 ma output. with 0-10 V output
www.cometsystem.com Instruction Manual T5140 T5141 T5145 Programmable transmitter of CO2 concentration with 4-20 ma output T5240 T5241 T5245 Programmable transmitter of CO2 concentration with 0-10 V output
More informationSTC-KNX (32-channel AP)
STC-KNX (32-channel AP) Bidirectional-Gateway between EnOcean and EIB/KNX-Bus Operating and installation instructions Humidity sensors Light sensors Presence sensors Gas sensors Room control panels Automated
More informationKNX ENO 634 (32-channel AP)
WEINZIERL GINEERING GmbH KNX O 634 (32-channel AP) Bidirectional-Gateway between EnOcean and KNX-Bus Operating and installation instructions Digital inputs Link from KNX to EnOcean actuator Switch Dimmer
More informationMx-RPW Room Control Module (Built-In Occupancy Sensor)
Wireless Room Controller Application Solar-powered, self-learning room sensor with LCD and smart communication management for measuring room temperature, independent generation of utilization time profiles
More informationLIGHT TRANSMITTER OPERATION MANUAL. 4 to 20 ma. Model : TR-LXT1A4
4 to 20 ma LIGHT TRANSMITTER Model : TR-LXT1A4 Your purchase of this LIGHT TRANSMITTER marks a step forward for you into the field of precision measurement. Although this TRANSMITTER is a complex and delicate
More informationCOD GB / 1.0 RBAND/UMS - RBAND/CSM
INTRODUCTION DESCRIPTION The RadioBand system is designed of Industrial, Commercial and Domestic door and gate applications where a safety edge is used. The system provides a wireless system replacing
More informationEBDSPIR-AT-DD. RF ceiling PIR presence detector DALI / DSI dimming. Product Guide. Overview. Features
Product Guide EBDSPIR-AT-DD RF ceiling PIR presence detector DALI / DSI dimming Overview The EBDSPIR-AT-DD is a passive infrared (PIR) motion sensor combined with two output channels capable of controlling
More informationElectrical devices may only be mounted and connected by electrically skilled persons.
Order No. : 5490.. Operating instructions 1 Safety instructions Electrical devices may only be mounted and connected by electrically skilled persons. Serious injuries, fire or property damage possible.
More informationwww.greenelectricalsupply.com Installation Guide Model: WLVD Wireless Low Voltage Dimmer (Receiver) Specifications: Power Supply 24 V DC Place on 24V power line prior to light load. 10A Maximum Load Package
More informationElectrical devices may only be mounted and connected by electrically skilled persons.
Art. No. : FM..1561.07.. Operating instructions 1 Safety instructions Electrical devices may only be mounted and connected by electrically skilled persons. Serious injuries, fire or property damage possible.
More informationBellman BRUGERVEJLEDNING. Fyrtårn Flash BE1441
Bellman EN BRUGERVEJLEDNING Fyrtårn Flash BE1441 Introduction The Visit system consists of a number of radio transmitters and receivers. The transmitters detect different events in the surrounding area
More informationSTR-LCF. Security Advice Caution. Notes on Disposal. Electronic Fan Coil Thermostat (Flush mounting) Datasheet. Application
STR-LCF Electronic Fan Coil Thermostat (Flush mounting) Datasheet Subject to technical alteration Issue date: 28.2.217 Application The fan coil room thermostat has been designed for individual control
More informationSentido KNX Manual. Sentido KNX. Manual. basalte bvba hundelgemsesteenweg 1a 9820 merelbeke belgium
basalte bvba hundelgemsesteenweg a 980 merelbeke belgium / 68 06 basalte Table of contents:. Introduction... 3. Installation... 4. 3. Identifying the parts... 5 General... 6 3. General functions... 7 3.
More informationRADIOBAND V3 Programming & Installation Manual
RADIOBAND V3 Programming & Installation Manual Radioband V3 User s Manual Introduction The RadioBand system is designed for Automatic Gates, Commercial and Domestic door applications where a safety edge
More informationJUMO Wtrans E01. Measuring probe for humidity, temperature, and CO 2 with wireless data transmission. Brief description. Universal Wtrans receiver
Page 1/13 JUMO Wtrans E01 Measuring probe for humidity, temperature, and CO 2 with wireless data transmission Humidity from 0 to 100 % RH (incl. -40 to +80 C) or CO 2 from 0 to 2000/5000/10000 ppm or Temperature
More informationUSER MANUAL. EPP Intelligent Positioner Control Unit 1/22.
USER MANUAL - Intelligent Positioner Control Unit 1/22 Table of contents: 1 General... 3 1.1 Safety instructions... 3 2 Application... 4 3 Electrical specifications and terminals... 5 3.1 Control loop...
More informationOVEN INDUSTRIES, INC. Model 5C7-362
OVEN INDUSTRIES, INC. OPERATING MANUAL Model 5C7-362 THERMOELECTRIC MODULE TEMPERATURE CONTROLLER TABLE OF CONTENTS Features... 1 Description... 2 Block Diagram... 3 RS232 Communications Connections...
More informationTechnical manual GS 4x.00 knx application description air quality sensor
Technical manual GS 4x.00 knx application description air quality sensor General Information The device fits for the particular use of the following tasks: monitoring of the air quality in building systems
More informationKNX TH65-AP. Thermo-Hygrometer. Installation and Adjustment. Item number 70184
EN KNX TH65-AP Thermo-Hygrometer Item number 70184 Installation and Adjustment 1 Content 1. Description... 3 1.1. Technical specifications... 3 2. Installation and commissioning... 4 2.1. Installation
More informationHUMIDITY/TEMP. CONTROLLER/MONITOR
HUMIDITY/TEMP. CONTROLLER/MONITOR Model : PHT-3109 Your purchase of this HUMIDITY/TEMP. CONTROLLER, MONITOR marks a step forward for you into the field of precision measurement. Although this METER is
More information1: White buttons Used by the user on a daily basis. 2: Grey buttons Used only upon first startup.
Fig. 1 Lock/ unlock 30 1000 Light 1 100 300 zone 1 Learn actual lux LED 600 2000 0,4 0,6 0,8 1,0 1,2 Time 1 Light 2 zone 2 1,4 1,6 Factor of lux zone 1 Pulse 2min 5min Time Time 2 10min 15min 30min 1 2
More information2F. No.25, Industry E. 9 th Rd., Science-Based Industrial Park, Hsinchu, Taiwan Application Note of OGM220, AN001 V1.8
Application Note of OGM220, AN001 V1.8 1.0 Introduction OGM220 series is a dual channels NDIR module having a digital output directly proportional to CO2 concentration. OGM220 is designed for multi-dropped
More informationDevice connection and commissioning can only be carried out by qualified professionals. Always make the connections while the power is switched off.
V1.2.0 (03.03.2014) 1 (21) This user guide is for controllers with the software version 1.2.0 or newer. WIRING Device connection and commissioning can only be carried out by qualified professionals. Always
More informationUse of the application program. Contents. instabus EIB Application program description. September S2 Room temperature controller
Use of the application program Product family: Product type: Manufacturer: Heating, Air conditioning, Ventilation Thermostat Siemens Name: Room temperature controller IKE 250 DELTA millennium Order no.:
More informationElectrical data Nominal voltage AC/DC 24 V Nominal voltage frequency
echnical data sheet LR24A-KNX Communicative rotary actuator for ball valves Nominal torque 5 Nm Nominal voltage AC/DC 24 V Control modulating Conversion of sensor signals Communication via KNX (S-Mode)
More informationPolyGard Digital Transmitter DGC DT-02
PolyGard Digital Transmitter DGC DT-02 Description LON interoperable digital gas transmitter to monitor toxic and combustible gases and vapors in the ambient air. The complete monitoring and alarm tripping
More informationRSMFX-2R MULTIFUNCTIONAL
Mounting and operating instructions Table of contents SAFETY AND PRECAUTIONS 3 PRODUCT DESCRIPTION 4 ARTICLE CODES 4 INTENDED AREA OF USE 4 TECHNICAL DATA 4 STANDARDS 4 OPERATIONAL DIAGRAMS 5 WIRING AND
More informationPlease enter the identity code of your device here!
Operating Instructions DULCOMETER D2C Part 2: Adjustment and Operation, Measured Variables ph/chlorine dioxide ProMinent D2C2-001-pH/CIO2-GB ph/clo 2 7.20 ph 0.45 ppm DULCOMETER STOP STAR T ph/clo 2 7.20
More informationEVALUATION OF HUMIDITY SENSORS IN A SWINE BARN
EVALUATION OF HUMIDITY SENSORS IN A SWINE BARN DEVELOPMENT AND TESTING OF A PROCEDURE TO EVALUATE HUMIDITY SENSORS IN LIVESTOCK BUILDINGS Stéphane-P. Lemay, Huiqing Guo, Ernie M. Barber and Lloyd Zyla
More informationtheben Fan Coil Actuator FCA 1 Fan Coil Actuator FCA 1 FCA Version: Jan-08 (Subject to change) Page 1 of 77
Fan Coil Actuator FCA 1 FCA 1 492 0 200 Version: Jan-08 (Subject to change) Page 1 of 77 Contents 1 Functional characteristics...4 1.1 Operation and display...5 1.2 Advantages of the FCA 1...5 1.2.1 Special
More informationWireless wall transmitter, 1-gang with inscription space, Wireless wall transmitter, 3-gang with inscription space
Wireless wall transmitter, 1-gang with inscription space Order No. : 5331.. Wireless wall Order No. : 5333.. Operating instructions 1 Safety instructions Electrical devices may only be mounted and connected
More informationWireless Room Temperature and Humidity Transmitter (Units without Temperature Setpoint or Override) Installation and Operating Instructions
Wireless Temperature and Humidity Overview and Indentification The Wireless Temperature and Humidity measures the room temperature and Relative Humidity and transmits the data at 418MHz or 433MHz RF to
More informationVENTI-LIGHT VLD. Ventilatie Indicator G e b r u i k e r s h a n d l e i d i n g. Ampèrestraat NL-1446 TR PURMEREND
VENTI-LIGHT VLD Ventilatie Indicator G e b r u i k e r s h a n d l e i d i n g mpèrestraat 35-37 NL-446 TR PURMEREND Postbus 783 NL-440 T PURMEREND T (+3) 099 630 60 F (+3) 099 630 6 E info@atal.nl I www.atal.nl
More informationENGLISH S-CO2 AMBIENT AIR SENSOR INSTALLATION AND OPERATING INSTRUCTIONS CO 2. TF5701_B_v1_web
S-CO2 CO 2 AMBIENT AIR SENSOR INSTALLATION AND OPERATING INSTRUCTIONS ENGLISH TF5701_B_v1_web 1 DESCRIPTION This module measures carbon dioxide (CO 2 ) in the range of 0 to 2 000 ppm and is equipped with
More informationCD-Pxx-00-0 Series Duct Mount CO 2 Transmitter
Installation Instructions CD-Pxx-00-0 Issue Date February 4, 006 CD-Pxx-00-0 Series Duct Mount CO Transmitter Application Requirements FCC Compliance Statement This equipment has been tested and found
More informationSTX Stair lighting controller.
Stair lighting controller STX-1792 STX-1792 controller is used to control stairs lighting dynamically. The backlight is switched on with the subsequent steps, depending on the motion directions: ascending
More informationAnalogue temperature controllers
Analogue temperature controllers CT8A Input by J-K thermo-couple or by thermo-resistance Pt 00 (-wire) regulation modes : ON/OFF or proportional derivative selected by wiring Relay output Specifications
More informationControl solutions Biofloor
MR24 Central radio controller 24V Connect COMAP offers the Connect control system as part of its underfloor heating and cooling solution. Composed of a central radio control module (MR24), wireless digital
More informationJPQ2 PULSE ACCUMULATOR
INSTRUCTION MANUAL PULSE ACCUMULATOR (field-programmable; built-in excitation) MODEL JPQ JPQ BEFORE USE... Thank you for choosing M-System. Before use, check the contents of the package you received as
More informationTX CONTROLLER Model EM-IP Quick Start Guide
TX CONTROLLER Model EM-IP Quick Start Guide 860 boul. de la Chaudière, suite 200 Québec (Qc), Canada, G1X 4B7 Tel.: +1 (418) 877-4249 Fax: +1 (418) 877-4054 E-Mail: gdd@gdd.ca Web site: www.gdd.ca Visit
More informationSeries 70 Servo NXT - Modulating Controller Installation, Operation and Maintenance Manual
THE HIGH PERFORMANCE COMPANY Series 70 Hold 1 sec. Hold 1 sec. FOR MORE INFORMATION ON THIS PRODUCT AND OTHER BRAY PRODUCTS PLEASE VISIT OUR WEBSITE www.bray.com Table of Contents 1. Definition of Terms.........................................2
More informationAqua-Gen 3BR INSTRUCTIONS
Aqua-Gen 3BR INSTRUCTIONS INSTALLATION INSTRUCTIONS CONTROLLER: Find a suitable location to mount the control box* radio note. The controller must be installed out of direct weather and no closer than
More informationRS232 CONTROLLER/MONITOR
RS232 CONTROLLER/MONITOR Model : PRS-2321 Your purchase of this RS232 CONTROLLER, MONITOR marks a step forward for you into the field of precision measurement. Although this RS232 CONTROLLER MONITOR is
More informationMonitoring Relay MR 50
Monitoring Relay MR 50 Standard signals 0/4... 20 m, 0/2... 10 V DC Features M Input standard signals 0/4... 20 m, 0/2... 10 V DC M Measuring range programmable M Basic accuracy 0.1 % +/- 1 Digit M Installed
More informationAqua-Gen 3PV INSTRUCTIONS
Aqua-Gen 3PV INSTRUCTIONS INSTALLATION INSTRUCTIONS CONTROLLER: Find a suitable location to mount the control box* radio note. The controller must be installed out of direct weather and no closer than
More informationUSER MANUAL ULD 910. October 2003 Revision: 03. Single Channel Vehicle Detector ULD 910. Part Number: MIC
Single Channel Vehicle Detector ULD 910 USER MANUAL Part Number: MIC0302004 ULD 910 October 2003 Revision: 03 I N D E X PAGE Detector Commissioning... 1 Frequency... 1 Sensitivity... 1 Automatic Sensitivity
More informationDLC-PDC PHOTODIODE CONTROLLER
DLC-PDC PHOTODIODE CONTROLLER INSTALLATION AND OPERATION INSTRUCTIONS 203 Cooper Circle, Peachtree City, GA 30269 Customer Service: Telephone: (800) 553-3879 Fax: (800) 954-7016 DLC-PDC Rev. 2 TABLE of
More informationLC8 & LC8-15. Single Level Lighting Controller INSTALLATION AND MAINTENANCE MANUAL (IMM) 205_LC8_R4
Single Level Lighting Controller INSTALLATION AND MAINTENANCE MANUAL (IMM) 205_LC8_R4 TABLE of CONTENTS 1 INTRODUCTON...3 1.1 GENERAL...3 1.2 OVERVIEW...3 2 INSTALLATION...4 2.1 POWER CONNECTIONS...4 2.2
More informationHyperioN 2. Instruction Manual. Wireless Environmental / Lighting Master Controller. Product #
HyperioN 2 Product #702880 Wireless Environmental / Lighting Master Controller Instruction Manual www.titancontrols.net Hyperion 2 Table of Contents Overview...4 Figure 1: Control Network... 5 Quick Set
More informationQuick Start Guide. ELPRO 905U-L-T Wireless I/O Transmitter Unit. man_905u-l-t_quickstart_v1-7.doc
Quick Start Guide ELPRO 905U-L-T Wireless I/O Transmitter Unit man_905u-l-t_quickstart_v1-7.doc ELPRO 905U-L-T Wireless I/O Transmitter Unit Quick Start Guide About this document This document is the ELPRO
More informationQAM Snare Isolator User Manual
QAM Snare Isolator User Manual QS-ISO-1.6 9/1/15 This document details the functions and operation of the QAM Snare Isolator leakage detector Table of Contents Overview... 3 Screen Navigation... 4 Settings...
More informationEBDHS-MB-AT-DD. RF ceiling PIR presence detector DALI / DSI dimming. Product Guide. Overview. Features
Product Guide EBDHS-MB-AT-DD RF ceiling PIR presence detector DALI / DSI dimming Overview The EBDHS-MB-AT-DD is a passive infrared (PIR) motion sensor combined with two output channels capable of controlling
More information5096 FIRMWARE ENHANCEMENTS
Document Number A100745 Version No.: 4.4.1 Effective Date: January 30, 2006 Initial Release: September 19, 2005 1. Fixed display of logged memory date and time broken in version 4.3. 2. Allow time samples
More informationOvazone-Core-Node-T Ovazone-Core-Router Manual
Ovazone-Core-Node-T Ovazone-Core-Router Manual ID7724 V9 20.9.2016 Firmware 1.0-1.2 Contents Introduction...3 Installation...4 Usage...9 Maintenance...9 Specifications... 10 Warnings... 12 Manufacturer...
More informationDual Technology Wall Mount Occupancy Sensor
LOS-WDT 1 11.04.08 Dual Technology Wall Mount Occupancy Sensor Models Available The wall-mount dual-technology sensors are used to control lighting in spaces that have pendant fixtures, ceiling fans, or
More informationeguard EG2233, EG3333, EG3355, EG3388 & EG8406: Installation and Set-up Procedures Tx 2200 and Rx 4200 Boards
eguard EG2233, EG3333, EG3355, EG3388 & EG8406: Installation and Set-up Procedures Tx 2200 and Rx 4200 Boards A. Primary Technical Data: Transmitter Operating voltage DC 24V Operating current. < 450mA
More information1000TR. Instructions
1000TR ph Instructions CONTENTS 1. INTRODUCTION... 2 1.1 COMMON INTRODUCTION... 2 1.2 PARTS & ACCESSORIES... 2 2. INSTALLATION... 3 2.1 CASING... 3 2.2 MOUNTING... 3 2.3 ELECTRICAL INSTALLATION... 3 2.3.1
More informationBrief description. Type overview
echnical data sheet VAV-Compact KNX A pressure sensor, digital VAV controller and damper actuator all in one, providing a VAV-Compact solution with a communications capability for pressureindependent VAV
More informationContents. English User Manual Regulators
Contents Safety warnings Page 28 Technical specifications Page 28 Description of instrument Page 31 Electrical connections Page 31 Glossary Page 32 Operation Page 37 Setting the regulation parameters Page
More informationFuzzy Temperature Controllers E5AF
Fuzzy Temperature Controllers 1/4 DIN Controller Combines Fuzzy and PID Control For Fast Response to Process Disturbances Advanced PID control provides optimal response during start-up and steadystate
More informationInstallation Manual. Ultra RF Analogue Transmitter QC0168. Manual Ref: QC0168. Version: March
Installation Manual Ultra RF Analogue Transmitter QC0168 Manual Ref: QC0168 Version: March 17 1.0 System Concept RF Transmitters connect to sensors or meters and send data to the infrastructure internet
More informationEIB/KNX, Indoor / Outdoor, IP65 Document: 3400_ex_SK08-GLBS.pdf Article No.
Seite 1 Product Page SK08-- MES Global Radiation Product Group 10 EIB/KNX, Indoor / Outdoor, IP65 Document: 3400_ex_SK08-.pdf Article No. SK08- -MES KNX - Global radiation sensor, silicon pyranometer pyranometer
More informationPRESSURE SENSORS I INSTALATION AND OPERATION INSTRUCTIONS ACCUTRON MDP BIDIRECTIONAL DIFFERENTIAL PRESSURE SENSOR
PRESSURE SENSORS I INSTALATION AND OPERATION INSTRUCTIONS ACCUTRON MDP BIDIRECTIONAL DIFFERENTIAL PRESSURE SENSOR ACC-MDP DIMENSIONS AND HARDWARE 2.10 " [5 3.40 mm ] 1.05 " [26.70 mm ] Ø0.19" [Ø4.76m m]
More informationWireless AC Circuit Identifier
User's Guide Wireless AC Circuit Identifier Models RT30 and RT30-E 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Back to the
More informationPlease enter the identity code of your device here!
Operating Instructions DULCOMETER D2C Part 2: Adjustment and Operation, Measured Variables chlorine/chlorine ProMinent D2C2-001-chlorine/chlorine-GB CI 2 /Cl 2 0.50 ppm CLE 0.20 ppm CI DULCOMETER STOP
More informationQuick Start Guide. ELPRO 105U-L-T Wireless I/O Transmitter Unit. man_105u-l-t_quickstart_v1-8.doc
Quick Start Guide ELPRO 105U-L-T Wireless I/O Transmitter Unit man_105u-l-t_quickstart_v1-8.doc ELPRO 105U-L-T Wireless I/O Transmitter Unit Quick Start Guide About this document This document is the ELPRO
More informationAutoDAB Connect In-Car DAB Adapter User Guide
AutoDAB Connect In-Car DAB Adapter User Guide www.autodab.com Table of Content INTRODUCTION... 1 CONTENTS OF PACKAGE... 2 INSTALLATION... 3 OPERATION CONTROLS... 8 STARTING UP THE SYSTEM... 11 USING REMOTE
More informationModel 12200A RCN PTAC/PTHP/FAN COIL CONTROL NODE OPERATION OUTPUTS G1 = FAN 1 G2 = FAN 2 G3 = FAN 3 O/B = Rev Valve W = HEAT Y = COMPRESSOR
Model 12200A RCN PTAC/PTHP/ COIL CONTROL NODE OPERATION OUTPUTS G1 = 1 G2 = 2 G3 = 3 O/B = Rev Valve W = HEAT Y = COMPRESSOR Operating Modes Summary (Refer to Logic Tables 1 5): 1. PTAC (Standard) Fan
More informationComfort Digisystem User Manual. SecureStream Technology. Receiver DH10. English
Comfort Digisystem User Manual SecureStream Technology Receiver DH10 English User manual Table of contents Page Introduction to the Comfort Digisystem 3 Functions of the Receiver DH10 4 Getting started
More informationCAST Application User Guide
CAST Application User Guide for DX900+ Electromagnetic Multilog Sensor U.S. Patent No. 7,369,458. UK 2 414 077. Patents Pending 17-630-01-rev.b 05/24/17 1 Copyright 2017 Airmar Technology Corp. All rights
More informationluxcontrol lighting control system basicdim basicdim ILD 16DPI 69f Compact control module with ambient light sensor and motion sensor
ILD 16DPI 69f Compact control module with ambient light sensor and motion sensor Product description Compact dimensions for luminaire installation For up to 10 DSI or LI devices (max. 5 per output channel)
More informationDISSOLVED OXYGEN TRANSMITTER
4 to 20 ma DISSOLVED OXYGEN TRANSMITTER Model : TR-DOT1A4 ATTENTION : Fill the Probe's Electrolyte at first. Intend to keep the DO probe under the best condition, when user receive the DIGITAL OXYGEN METER
More informationVBRC 5. Radio Communicator. Installer Manual
VBRC 5 Radio Communicator Installer Manual 10 / 10 / 2013 CONTENT 1. INTRODUCTION...3 2. SYSTEM STRUCTURE...3 3. SYSTEM PROGRAMMING WITH PC SOFTWARE...5 4. TROUBLESHOOTING...6 5. FIRMWARE UPGRADE...7 6.
More informationThe Smallest, Quietest & Safest Garage Door Operator in the World!
ZAP Technical Instruction The Smallest, Quietest & Safest Garage Door Operator in the World! Function Programming Series controller applicable to: 800 II G, 800 II, 8800 II, 8800 II HP, 8850 These functions
More informationTechnical Application Guide
Lighting Control Wireless Occupancy Sensor, Wireless Multi Sensor Technical Application Guide Easily enhance your smart lighting system with the Philips wireless occupancy sensor and multi sensor, which
More informationEnglish RACON SERIES II RADIO CONTROL SERVICE MANUAL
English 22.2.2007 RACON SERIES II RADIO CONTROL SERVICE MANUAL Read the instructions supplied with the product before installation and commissioning. Keep the instructions in a safe place for future reference.
More informationCONTROL MANUAL. Dry-Pic 09PE - 09VE
CONTROL MANUAL Dry-Pic 09PE - 09VE Translation of the original document 003, 04.01 EN CONTENTS PAGE 1 - IMPORTANT RECOMMENDATIONS 1.1 Power supply 1. Electronic board specifications 1.3 Caution 1.4 Earth
More informationCX105 Conductivity/Resistivity Transmitter
CX105 Conductivity/Resistivity Transmitter User Manual REV A.15 Sensorex Corporation, USA 11751 Markon Drive Garden Grove, CA. 92841 U.S.A. www.sensorex.com IMPORTANT SAFETY INFORMATION Please read and
More informationinstabus EIB product documentation
Page: 1 of 39 Push button interface 4-gang Sensor Product name: Push button interface 4-gang Design: UP (flush-mounting type) Item no.: 2076-4T-01 ETS search path: Input / Binary Input, 4-gang / Push button
More informationIXIAN TM class V 1.5. EC Transmitter This is an evolving document. EC Transmitter IXIAN TM. Features
class V 1.5 EC Transmitter This is an evolving document check back for updates. Features 4 20mA output Reads conductivity from 0.07µs to 100,000µs Accuracy +/- 2% Calibrate remotely through a PLC or directly
More informationT-1WF(V) Instruction Manual. Long Range LLC. 26 Tannery Street Franklin, NH 03235
T-1WF(V) Instruction Manual Long Range LLC. 26 Tannery Street Franklin, NH 03235 Introduction With the ability to fire targets and control the direction of your trap, the T-1WF transmitter is the perfect
More informationKNX manual 1-channel flush-mounted switch actuator SU 1
KNX manual 1-channel flush-mounted switch actuator SU 1 4942520 2018-10-04 Contents 1 Function description 3 2 Operation 4 3 Technical data 5 4 The SU 1 application programme 7 4.1 Selection in the product
More informationEPSON Stylus COLOR 300. Accessories. Printer Specifications. User Replaceable Parts. Cartridge. Media. Printing
paper support Accessories edge guides left edge guide lock lever paper thickness lever power switch Ink Cartridge Use only the ink cartridge specified in the table below with the EPSON Stylus COLOR 300.
More informationElectrical data Nominal voltage AC/DC 24 V Nominal voltage frequency
echnical data sheet LR24A-KNX Communicative rotary actuator for ball valves Nominal torque 5 Nm Nominal voltage AC/DC 24 V Conversion of sensor signals echnical data Electrical data Nominal voltage AC/DC
More informationRAM 712 KNX room thermostat for surface-mounted and flush-mounted installation
RAM 712 KNX room thermostat for surface-mounted and flush-mounted installation RAM 712 712 9 200 Version: Dec-10 (subject to change) Page 1 of 65 Contents 1 Functional characteristics... 4 1.1 Operation...
More informationWireless Temp/Setpoint & Override Room Transmitter
Overview The BAPI Wireless Combination Transmitter measures the room temperature and relative humidity and transmits the data at 418MHz or 433MHz RF to a receiver. Temperature setpoint and override button
More informationCLIMATE. Climate sensors to ensure comfort and productivity
CLIMATE Climate sensors to ensure comfort and productivity CLIMATE We produce climate sensors to ensure productivity and comfort in animal production. dol-sensors manufactures sensors for temperature,
More informationConfiguration of CPE 310-S and CPE 311-S transmitters by keypad
Configuration of CPE 310-S and CPE 311-S transmitters by keypad Table of contents 1. Introduction...5 1.1. Description of the transmitter...5 1.2. Description of the keys...5 1.3. Protection tips of the
More informationRADIOBAND 3G RB3 T868 RB3 R868 USER'S MANUAL
RADIOBAND 3G RB3 T868 RB3 R868 USER'S MANUAL Index INTRODUCTION... 3 Operating... 3 Receiver RB3 R868... 4 Transmitter RB3 T868... 5 ASSEMBLY AND INSTALLATION... 6 1 Installation of the equipment... 6
More information