REVISIONS INDEX 2016 ROAD & BRIDGE STANDARDS
|
|
|
- Ella Potter
- 5 years ago
- Views:
Transcription
1 REVISIONS INDEX 2016 ROAD & BRIDGE STANDARDS December 2018 Revision Letter September 2018 Revision Letter September 2017 Revision Letter August 2017 Revision Letter February 2017 Revision Letter
2 Signature on File 12/12/18
3
4 ADDED ST D PA-3 BACK INTO THE ROAD & BRIDGE STANDARDS. STANDARD PA-4 MOVED TO SHEET ST D PA-3 MODIFIED FROM VERSION IN 2008 ROAD & BRIDGE STANDARDS TO SHOW APS UNITS, WITH UPDATED MIN AND MAX MOUNTING HEIGHT NEW SHEET WITH STANDARD PA-4. LENGTH OF PEDESTAL SHORTENED FROM 6 0 TO 5 0. ALLOW OUTSIDE DIAMETER TO BE 4.0 INSTEAD OF 4.5. FOUNDATION WIDTH SHRUNK FROM 24 TO 18. ALLOW PREAPPROVED BAG MIX TO BE USED INSTEAD OF CLASS A3 CONCRETE. CHANGED PEDESTRIAN PUSH BUTTON REFERENCE TO ACCESSIBLE PEDESTRIAN SIGNAL (APS) UNIT. PEDESTAL TUBE ALLOWED TO BE SCHEDULE 40 INSTEAD OF SCHEDULE 80 ELIMINATED REFERENCES TO USE OF STAINLESS STEEL BANDS FOR ATTACHING BUTTON AND SIGNS TO POLES. CHANGED MIN AND MAX MOUNTING HEIGHTS FOR BUTTONS ADDED VIBRATION DAMPENERS REVISED LOCATOR TAPE REQUIREMENTS IN NOTE 1 CLARIFIED DEPTH DIMENSIONS TO TOP OF CONDUIT IN ALL SECTION VEIWS NEW FOUR INCH SQUARE TUBE SIGN POST STANDARD ADDED REFERENCE TO NOTE 13 FOR POLE-MOUNTED CABINET AND CCTV CAMERA CALLOUTS SIGNIFICANT REVISIONS TO VERTICAL CLEARANCE REQUIREMENTS IN NOTE #5. ADDED NOTE OSS-1 STANDARDS EXPANDED TO 7 SHEETS OSS-1 STANDARDS EXPANDED TO 7 SHEETS REVISE DISTANCE BETWEEN SAFETY SWITCH AND CONTACTOR FROM 24 MAX TO 6 MAX. ADDED NOTES BENEATH PE CONTROL AND CONTACTOR CALLOUTS SHEETS 6 AND 7 OF 7 REORGANIZED SO THAT ALL SIGN HANGER DETAILS ARE ON SHEET 6 AND ALL SIGN LIGHTING DETAILS ARE ON SHEET 7. ELIMINATED REQUIREMENT TO TILT THE SIGN FACE 3 DEGREES DOWNWARD. ADDED NOTES REFERENCING WHERE ISOLATION MATERIALS BETWEEN DISSIMILAR METALS ARE REQUIRED. Page 2 of 3
5 SHEETS 6 AND 7 OF 7 REORGANIZED SO THAT ALL SIGN HANGER DETAILS ARE ON SHEET 6 AND ALL SIGN LIGHTING DETAILS ARE ON SHEET 7. EMPHASIZED THAT LUMINAIRE RETRIEVAL SYSTEMS SHALL ONLY BE INSTALLED WHERE REQUIRED ON THE PLANS. ELIMINATED REFERENCES TO PROPRIETARY LUMI-TRAK SYSTEM. ADDED DETAILS FOR INSTALLATION OF LUMINAIRES WITHOUT A RETRIEVAL SYSTEM. ELIMINATED THE REQUIREMENT TO INSTALL HORIZONTAL LUMINAIRE ARMS FOR STRUCTURES THAT WILL NOT BE ILLUMINATED. CLARIFIED THAT HORIZONTAL ARMS ARE LUMINAIRE, NOT SIGN, HANGER ARMS TO DISTINGUISH THEM FROM THE (VERTICAL) SIGN HANGERS CHANGED DISTANCE BETWEEN VERTICAL SPLICES FROM 2 MIN. 5 MAX, TO 4 MIN ADDED ASTERISKED NOTE CLARIFYING WHERE DIMENSIONS c AND d ARE MEASURED TO. If you have any questions or comments regarding the 2016 Road & Bridge Standards, please contact Charles Patterson, P.E., at (804) , of the Standards and Special Design Section. Sincerely, Signature on file Date: 10/10/2018 Susan H. Keen, P.E. State Location & Design Engineer Page 3 of 3
6
7 ADDED DETAIL FOR TRANSITION FROM GR-MGS1 TO WEAK POST GUARDRAIL. If you have any questions or comments regarding the 2016 Road & Bridge Standards, please contact Charles Patterson, P.E., at (804) , of the Standards and Special Design Section. Sincerely, Signature on file Date: 9/26/17 Susan H. Keen, P.E. State Location & Design Engineer Page 2 of 2
8
9 Section 1300: Revised index pages , , , & MP-2 CHANGE LUMINAIRE CALLOUT FROM TRUSS TYPE LUMINAIRE ARM TO LUMINAIRE ARM MP-3 CHANGE LUMINAIRE CALLOUT FROM TRUSS TYPE LUMINAIRE ARM TO LUMINAIRE ARM. CHANGED DIMENSION FROM TOP OF POLE TO CENTER OF ARM FROM 12 TO 12 MIN MP-3 CHANGE CASE X LOADING CALLOUT TO LOADING CASE X AB-1 REVISED NOTE VS-1 REVISED NOTE PA-4 REMOVED PA-3 DETAIL FROM THE STANDARDS LF-1 REVISED NOTE LP-1, 2 CHANGED BRACKET ARM LENGTH TO LUMINAIRE ARM LENGTH. SHOW BOTH LP-1 AND LP-2 STRUCTURES ON TRANSFORMER BASES; CLARIFY IN NOTES THAT STRUCTURES SHALL BE ON EITHER BREAKAWAY OR NON-BREAKAWAY TRANSFORMER BASES; REVISIONS TO NOTES REGARDING TRANSFORMER BASE INSTALLATION. DELETED NOTE REGARDING WIRE SUPPORT J-HOOKS FOR HAND HOLES MORE THAN 4 FEET UP THE STRUCTURE JB-R1, R2 CLARIFICATION REGARDING NUMBER OF PLACEMENT OF REQUIRED J-HOOKS; MINOR DRAFTING IMPROVEMENTS; REVISED REQUIREMENTS FOR PLACEMENT OF AGGREGATE UNDERNEATH THE JUNCTION BOX AND COMPACTED EARTH ON SIDES OF JUNCTION BOX; CONDUIT ENTRANCE DEPTH REVISED TO READ INSTEAD OF 18 ; DELETION OF NOTES THAT ARE DUPLICATES OF REQUIREMENTS IN THE SPECIFICATIONS JB-R1, R2 MINOR REVISIONS TO NOTES JB-S1, S2, S3, S4 ADDITION OF 48 X 48 JB-S4 STANDARD; DELETION OF REQUIREMENT THAT JB S BE ONE- OR TWO- PIECE IN DESIGN; CLARIFICATION OF AGGREGATE AND COMPACTED SOIL PLACEMENT UNDERNEATH AND AROUND BOX; REVISION TO NOTE REGARDING ACCEPTABLE METHODS OF LABELING BOXES; CLARIFICATION REGARDING NUMBER OF PLACEMENT OF REQUIRED J-HOOKS; CONDUIT ENTRANCE DEPTH REVISED TO READ INSTEAD OF 18 ; CORRECTED ERROR IN PREVIOUS STANDARD REGARDING LABELING OF DIMENSIONS A AND B JB-S4 NEW SHEET WITH DETAILS FOR 48 X 48 JB-S4 JUNCTION BOX WSP-1 STANDARDS EXPANDED TO 7 SHEETS WSP-1 STANDARDS EXPANDED TO 7 SHEETS WSP-1 STANDARDS EXPANDED TO 7 SHEETS WSP-1 SOME DETAILS MOVED TO SHEET 5 Page 2 of 3
10 Section 1300: WSP-1 SQUARE TUBE POST DESIGN TABLE MOVED TO SHEET 6. SHEET 5 NOW ENCOMPASSES DETAILS FOR SIGN PANEL ATTACHMENTS TO POSTS, INCLUDING NEW ALTERNATE ATTACHMENT DETAILS AND NEW DETAILS FOR MOUNTING OF BACK-TO-BACK SIGNS WSP-1 SQUARE TUBE POST DESIGN TABLE MOVED FROM SHEET WSP-1 NEW SHEET WITH SPLICE AND CORNER BOLT DETAILS PREVIOUSLY INCLUDED ON SHEET 6. ORIENTATION OF CORNER BOLTS CHANGED SO THAT ALL CORNER BOLT HEADS ARE ON LEFT SIDE STP-1 SINGLE POST MEDIAN INSTALLATION DETAIL MOVED FROM SHEET 12; ADDED NOTES 9 AND STP-1 CORRECTED CALLOUT FOR DRIVE TUBE FOUNDATION MATERIALS TO REQUIRE 3/16, NOT 1, STEEL PLATE STP-1 SOME DETAILS MOVED TO SHEET 12 OF STP-1 INCREASED ALLOWABLE MAXIMUM WIDTH OF SIGN ON A SINGLE POST FROM 5 FEET TO 6 FEET STP-1 DETAILS REGARDING SIGN MOUNTING HEIGHT/PLACEMENT FOR INTERCHANGE OFF-RAMPS MOVED TO NEW STANDARD ISD-1. SIGN BRACING DETAILS MOVED FROM SHEET 10 TO SHEET 12. NEW DETAILS WITH ALTERNATE SIGN PANEL MOUNTING DETAILS, AND NEW DETAILS SHOWING HOW TO ATTACH BACK-TO-BACK SIGN PANELS ON THE SAME POST ISD-1 NEW STANDARD SHOWING SPECIAL SIGN PLACEMENT AND MOUNTING HEIGHT REQUIREMENTS FOR CERTAIN SIGNS ON INTERCHANGE OFF-RAMPS. Any questions related to Section 1300 should be directed to the Traffic Engineering Division. If you have any questions or comments regarding the 2016 Road & Bridge Standards, please contact Charles Patterson, P.E., at (804) , of the Standards and Special Design Section. Sincerely, Signature on file Date: 8/31/17 Susan H. Keen, P.E. State Location & Design Engineer Page 3 of 3
11
12 The following Special Design sheets were added to the Central Office Environment on Falcon DMS and the FTP Server. RSS Reinforced Soil Slope (Sheets 1-2) If you have any questions or comments regarding the 2016 Road & Bridge Standards, please contact Charles Patterson, P.E., at (804) , of the Standards and Special Design Section. Sincerely, Signature on File Date: 2/16/17 B. A. Thrasher, P.E. State Location & Design Engineer Page 2 of 2
REVISIONS INDEX 2016 ROAD & BRIDGE STANDARDS. September 2017 Revision Letter August 2017 Revision Letter February 2017 Revision Letter
REVISIONS INDEX 2016 ROAD & BRIDGE STANDARDS September 2017 Revision Letter August 2017 Revision Letter February 2017 Revision Letter 506.08 ADDED DETAIL FOR TRANSITION FROM GR-MGS1 TO WEAK POST GUARDRAIL.
Ohio Department of Transportation Office of Roadway Engineering January 18, 2013
Ohio Department of Transportation Office of Roadway Engineering January 18, 2013 To: Holders of the Traffic Standard Construction Drawings (SCDs) and Plan Insert Sheets (PISs) As of January 18, 2013, eighteen
Current Standard Plates including Transmittal Letters are available on the web at:
MINNESOTA DEPARTMENT OF TRANSPORTATION DEVELOPED BY: Design Standards ISSUED BY: Office of Project Management and Technical Support, Design Support Section TRANSMITTAL LETTER NO. (17-04) MANUAL: Standard
To: All Holders of the Virginia Department of Transportation s 2001 Road and Bridge Standards
DEPARTMENT OF TRANSPORTATION 1401 EAST BROAD STREET RICHMOND, VIRGINIA 23219-2000 PHILIP A. SHUCET COMMISSIONER July 21, 2004 MOHAMMAD MIRSHAHI, P.E. STATE LOCATION AND DESIGN ENGINEER MEMORANDUM To: All
INSTRUCTIONS: 1. Record the transmittal letter number, date, and subject on the transmittal record sheet located in the front of the manual.
MINNESOTA DEPARTMENT OF TRANSPORTATION DEVELOPED BY: Design Standards ISSUED BY: Office of Technical Support Design Services Section TRANSMITTAL LETTER NO. (0-03) MANUAL: Standard Plates DATED: September
SIGNALS AND LIGHTING FIELD GUIDE
CHAPTER 16 SIGNAL AND LIGHT POLES SIGNAL AND LIGHT POLES The standards and requirements for installing traffic control signal and light poles are presented in this chapter. 16.1 Traffic Control Signal
Standard Plate 7036 is discontinued. It is replaced by Standard Plan Pedestrian Curb Ramp Details.
DEVELOPED BY: Design Standards ISSUED BY: Office of Program Management & Technical Support, Design Support Section TRANSMITTAL LETTER NO. (12-02) MANUAL: Standard Plates DATED: May 11, 2012 SUBJECT: Standard
MDOTProjectwise\Documents\Reference Documents\Traffic Reference\Statewide Special Details\Develop
500 460 MDOTProjectwise\Documents\Reference Documents\Traffic Reference\Statewide Special Details\Develop Check if Applicable TRAFFIC SIGNAL SPECIAL DETAILS INDEX/CHECKLIST *One completed checklist required
Standard Signs Manual
Standard Signs Manual NEW, CHANGED, OR DELETED 1/2017 STANDARD SIGN DETAILS Title Page Number Fractions... 101 Straight Arrows... 102 Double Head Arrows... 102A Double Head Arrows - 90... 102B Advance
Manhole or Catch Basin Type A & B Cone Sections Precast - Design F Manhole or Catch Basin Cover (Reducer Cone Section Precast) Design D
MINNESOTA DEPARTMENT OF TRANSPORTATION DEVELOPED BY: Design Standards ISSUED BY: Office of Program Management and Technical Support, Design Support Section TRANSMITTAL LETTER NO. (14-02) MANUAL: Standard
Guide Sign Policy for Secondary State Highways Edition
Massachusetts Highway Department, Ten Park Plaza, Boston, MA 02116-3973 ` Guide Sign Policy for Secondary State Highways 2005 Edition Revised September 2005 1. PURPOSE The Massachusetts Highway Department
SUBJECT: Standard Plates 4132, 4155, Drainage Structures and Castings Info
MINNESOTA DEPARTMENT OF TRANSPORTATION DEVELOPED BY: Design Standards ISSUED BY: Office of Project Management and Technical Support, Design Support Section TRANSMITTAL LETTER NO. (18-01) MANUAL: Standard
2. Remove from the Standard Plate manual: Standard Plate Index, Sheets 1-4 of 4, Numerical Index of Standard Plates (August 31, 2012)
MINNESOTA DEPARTMENT OF TRANSPORTATION DEVELOPED BY: Design Standards ISSUED BY: Office of Program Management & Technical Support, Design Support Section TRANSMITTAL LETTER NO. (12-04) MANUAL: Standard
SIG-032-B TRAFFIC SIGNAL MAST ARM POLE AND MAST ARM DETAILS - CATEGORY III LUMINAIRE ARM (SEE CONTRACT) 6'-0", 8'-0", 10'-0" NOMINAL SPREAD
Michigan Department of Transportation 6'-0", 8'-0", 10'-0" NOMINAL SPREAD (SEE CONTRACT) LUMINAIRE ARM (SEE CONTRACT) POLE CAP 1'-6" (6'-0" ARM) 1'-10" (8'-0" ARM) 2'-0" (10'-0" ARM) NOMINAL RISE 2.38"
SIG-030-B TRAFFIC SIGNAL MAST ARM POLE AND MAST ARM DETAILS - CATEGORY I LUMINAIRE ARM 6'-0", 8'-0", 10'-0" NOMINAL SPREAD (SEE CONTRACT) POLE CAP
Michigan Department of Transportation 6'-0", 8'-0", 10'-0" NOMINAL SPREAD (SEE CONTRACT) LUMINAIRE ARM (SEE CONTRACT) POLE CAP 1'-6" (6'-0" ARM) 1'-10" (8'-0" ARM) 2'-0" (10'-0" ARM) NOMINAL RISE 2.38"
E:\Wilmot\DGN\14018pp.dgn 3/11/2015 6:49:16 AM
600-06 SHOULDER WIDENING FOR TYPE (SPECIAL) GUARDRAIL TERMINALS E:\Wilmot\DGN\08pp.dgn //05 6:9:6 AM E:\DGN\08SUP.dgn //05 ::55 PM E:\DGN\08SUP.dgn //05 :8:0 PM E:\DGN\08-WRG.dgn //05 :8:5 PM E:\DGN\08SM.dgn
Ohio Department of Transportation Office of Traffic Engineering July 17, 2009
Ohio Department of Transportation Office of Traffic Engineering July 17, 2009 To Holders of the OTE Standard Construction Drawings (SCDs) and Plan Insert Sheets (PISs): As of July 17, 2009, fifteen SCDs
Open shipping crate and separate all of the different parts. Over The Top Shelters LLC
ASSEMBLY INSTRUCTIONS FOR MODEL SH122110GN and SH122110GY Open shipping crate and separate all of the different parts. Count each part and match up with parts list. Shortages or damaged parts should be
SUBJECT: Standard Plate 9102 Turf Establishment Areas At Pipe Culvert Ends
MINNESOTA DEPARTMENT OF TRANSPORTATION DEVELOPED BY: Design Standards ISSUED BY: Office of Project Management and Technical Support, Design Support Section TRANSMITTAL LETTER NO. (17-03) MANUAL: Standard
Current Standard Plates including Transmittal Letters are available on the web at:
MINNESOTA DEPARTMENT OF TRANSPORTATION DEVELOPED BY: Design Standards ISSUED BY: Office of Project Management and Technical Support, Design Support Section TRANSMITTAL LETTER NO. (15-03) MANUAL: Standard
SUBJECT: Standard Plate Turf Establishment Areas (at Pipe Culvert Ends)
MINNESOTA DEPARTMENT OF TRANSPORTATION DEVELOPED BY: Design Standards ISSUED BY: Office of Program Management and Technical Support, Design Support Section TRANSMITTAL LETTER NO. (14-01) MANUAL: Standard
REVISION INFORMATION SHEET ONTARIO PROVINCIAL STANDARDS FOR ROADS AND PUBLIC WORKS
Ontario Provincial Standards 301 St. Paul St., 2 nd Floor North St. Catharines, ON L2R 7R4 REVISION INFORMATION SHEET ONTARIO PROVINCIAL STANDARDS FOR ROADS AND PUBLIC WORKS VOLUME 4 MUNICIPAL AND PROVINCIAL
SIGN MOUNTED BEACON SIG-027-A SINGLE SIGN MOUNTED FLASHING BEACON INSTALLED ON ONE WOOD POST DETAIL "A-1"
1 1/2" x 60" Galvanized (thread both ends) Top Bolt See Detail "A-1" and Slotted Channel Parallel Conduit Clamp Warning Sign 3 Equal Bolt Spacings (3 places at 12" min. spacing) (1) 3/8"x 7" min. (4"x
UPM 6X Custom. UPM 6X CUSTOM Standard stock Tee socket sized for 5" schedule 40 or 80 Pipe. Page 1 of 8
Page 1 of 8 UPM 6X Custom A. TEE SOCKET: 6 O.D. PIPE SOCKET TO FIT OVER 5 SCHEDULE 40 or 80 STEEL PIPE B. CROSS PIECE: 2 X 2 X 3/16, LENGTH DEPENDENT ON MODULE USED, SQUARE TUBE 2 PLACES C. LONGITUNDINAL:
Standard 25 Wide Structure
Standard 25 Wide Structure Truss Arch Style 2 piece 12ft c/c typical Arch Depth 12 Webbing Diameter 1/2 1 run straight 2 runs straight Wind Brace - up to 120 8 Wind Brace - up to 192 12 Wind Brace - over
This specification describes the minimum technical requirements for drawings, as applicable to all disciplines.
SPEC-0800 1/5 1.0 PURPOSE This specification describes the minimum technical requirements for drawings, as applicable to all disciplines. 2.0 VALE DRAWING TYPE DEFINITIONS Engineering Drawings Engineering
SECTION R507 DECKS DECKING LEDGER BOARD BEAM. FOOTING BEAM SPAN CANTILEVER For SI: 1 inch = 25.4 mm FIGURE R507.2 DECK CONSTRUCTION
SECTION R507 DECKS R507.1 Application. The provisions of this section shall provide prescriptive requirements for the design and construction of all uncovered, wood-framed, single-span exterior decks.
OHIO DEPARTMENT OF TRANSPORTATION CENTRAL OFFICE, 1980 W. BROAD ST., COLUMBUS, OHIO
OHIO DEPARTMENT OF TRANSPORTATION CENTRAL OFFICE, 1980 W. BROAD ST., COLUMBUS, OHIO 43216-0899 July 20, 2012 To: Users of the Standard Bridge Drawings From: Tim Keller, Administrator, Office of Structural
Track Rack. * Track Racks are not lockable
The Track Rack s unique staggered, sliding hook design creates the greatest parking efficiency while still providing easy access to any particular bike. When adding or removing a bike to the rack, simply
DECKS. Stairway illumination Positive attachment of ledger Lateral load connection required board (R507.2) required (R ) (R311.7.
DECKS Max. riser height-7 ¾ Min. tread depth-10 Landings required at (R311.7.5.1) (R311.7.5.2) top and bottom of stairs (R311.7.6) Notched guardrail post NOT allowed Graspable handrail required Spacing
6/19/2014. Milton Madison Bridge Slide. Project Partners. The Challenge. Aaron L. Stover, PE, SE Michael Baker Jr., Inc.
Kentucky Society of Professional Engineers May 23 rd, 2014 Lexington KY Milton Madison Bridge Slide Aaron L. Stover, PE, SE Michael Baker Jr., Inc. Project Partners The Challenge Milton, KY Existing Bridge
MH Table of Contents Standard Title/Scope Page Table of Contents SCE Public
MH Table of Contents Standard Title/Scope MH 300 MH 310 MH 318 MH 320 MH 325 MH 330 MH 335 MH 340 MH 350 Manholes Requirements MH 300.1 Manholes Requirements...........................................
Chapter 25. Lighting Plans
Chapter 25 Lighting Plans The following are changes, additions or deletions to the January 2014, Topic #625-000-008, Plans Preparation Manual (PPM), for use on Turnpike projects only. 25.1 General Replace
INVITATION TO BID. * EA Mounted) 24 Detector Card (NEMA TS-2) * EA 25 Concrete Curb Ramp *848 5 EA
INVITATION TO BID TOWN OF CARY Cary, North Carolina Sealed bids must be submitted no later than 1:30 p.m. on October 1, 2018 to the Town of Cary at the office of the Transportation and Facilities Department],
Manholes Table of Contents
Standard MH 300 Title Manholes Requirements MH 300.1 Manholes Requirements Manholes Table of Contents Underground Structures Standards MH 310 MH 318 MH 320 MH 325 MH 330 MH 335 MH 340 MH 350 Precast Tub-Type
B " 787
175'0" 53339 3H:1V S.B.P. 25" 635 3H:1V Slope 100'0" 30480 Soil Cut 3H:1V Slope 58" 1474 75" 05 1 2 3 4 5 6 7 8 9 10 11 12 13 25 14 15 16 17 18 20 21 22 23 24 25 2270P Impact 243 60 12 Spaces @ 75" [05]
Plate 8132A - Preformed Rigid PVC Conduit Loop Detector, is a new plate requested by OTST.
DISTRIBUTION: 7 MINNESOTA DEPARTMENT OF TRANSPORTATION DEVELOPED BY: Design Standards ISSUED BY: Design Services Section TRANSMITTAL LETTER NO. (0-0) MANUAL: Standard Plates DATED: January 9, 00 SUBJECT:
Midwest Roadside Safety Facility
C 1690" A 42926 75" 1905 150" 3810 G E F F 11 10 9 8 7 6 5 4 3 2 C D D 25 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 21.2 G E Impact 2270P 17 Spaces @ 75" [1905] Spacing = 106' 3" [32385] 1 1662 1/2"
System 3000 specifications
System 3000 specifications Scope: Materials: Type of Bookstack: This specification covers delivery and installation of steel library shelving of the bracket type. Height, depth and accessories shall be
CITY OF TUMWATER 555 ISRAEL RD. SW, TUMWATER, WA (360)
CITY OF TUMWATER 555 ISRAEL RD. SW, TUMWATER, WA 98501 (360) 754-4180 Email: cdd@ci.tumwater.wa.us WATER-SEWER-STREET-STORM (IN CITY) Submittal Checklist TUM - RCVD BY DATE STAMP APPLICANT INFORMATION
5/16" Flange nut. Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector zinc plated bolt w/ washers and nut. Anchor 3" sq. 7 Ga.
2 1/2" x 2 1/2" x 10 Ga. 6" 5" 4" Variable Slipbase (8" Sq. SYS.) 5/16 Corner Bolt W/ nut 5/16" Flange nut Stub Insert (8" Sq. SYS.) Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector zinc
GENERAL ISOMETRIC LAYOUT
EXISTING OR PROPOSED WIPER WALL SUPPORT STRUCTURE GATE LID CARBATHAN HG 0 WEB GRAY LOWER PAN GRATING ALUMINUM WIPER WALL CARBATHANE HG, 90 GRAY STRUCTURAL SPECIFICATIONS:. FLOODGATE MATERIAL TO BE ALUMINUM
OREGON DEPARTMENT OF TRANSPORTATION
OREGON DEPARTMENT OF TRANSPORTATION TRAFFIC SIGNAL DESIGN MANUAL The material contained herein is for information purposes only and may be used to aid new employees, and those unfamiliar with ODOT Traffic
FXL-168 FIXED RACK ASSEMBLY INSTRUCTIONS SALES ORDER #
ZOMEWORKS FXL-168 FIXED RACK ASSEMBLY INSTRUCTIONS SALES ORDER # 1 1011 Sawmill Road NW, PO Box 25805, Albuquerque, NM 87125 USA (505) 242-5354 / (800) 279-6342 / FAX (505) 243-5187 E-mail: zomework@zomeworks.com
Vertical Offset Base and Safety Rail System Installation Instructions
Section 5 Vertical Offset Base and Safety Rail System Installation Instructions The vertical offset base and safety rail assembly are designed to be used in residential construction for sloped or flat
Installation Instructions for. Handrail Component System
Handrail STEP-BY-STEP Installation Instructions for Handrail Component System Rise in Inches Run in Inches 8 8.5 9 9.5 10 10.5 11 11.5 12 12.5 13 13.5 14 14.5 15 8.5 47 45 43 42 40 39 38 36 35 34 33 32
CITY OF WHITE PLAINS STANDARD DESIGN CRITERIA AND SPECIFICATIONS FOR SMALL WIRELESS FACILITIES
CITY OF WHITE PLAINS STANDARD DESIGN CRITERIA AND SPECIFICATIONS FOR SMALL WIRELESS FACILITIES Small 1.1 Definitions: Antenna - Communications equipment that transmits or receives electromagnetic radio
SwingSafe Swing-Away Mailbox Support Diagram
SwingSafe Swing-Away Mailbox Support Diagram Wood Mounting Plates Top Arm (B) Muffler Clamps (A) Carriage Bolts and Nuts Bottom Arm 4-Foot U-Channel Post USPS Recommended 42-44 Height Ground Slope Hex
602.4, TABLE 602.4, , , , , , , , , TABLE
602.4, TABLE 602.4, 602.4.1, 602.4.2, 602.4.3, 602.4.4, 602.4.5, 602.4.9, 2304.11, 2304.11.1, TABLE 2304.11.1.1, 2304.11.2, 2304.11.3, 602.4.8, 602.4.8.2, 602.4.8.1, 602.4.6, 602.4.6.2, 602.4.6.1, 2304.11.4,
UPM 6X. UPM 6X Standard stock Tee socket sized for 5" schedule 40 or 80 Pipe. Page 1 of 8
Page 1 of 8 UPM 6X A. TEE SOCKET: 6 O.D. PIPE SOCKET TO FIT OVER 5 SCHEDULE 40 OR 80 STEEL PIPE B. CROSS PIECE: 2 X 2 X 1/8, LENGTH DEPENDENT ON MODULE USED, SQ. TUBE 2 PLACES C. LONGITUDINAL: 2 X 2 X
Midwest Roadside Safety Facility
28 Spaces @ 75"=2100" 100' 3:1 Cut 40' 75" (TYP.) 3:1 Soil Cut 3:1 1 2 3 4 5 6 7 8 9 10 25 12 13 11 14 15 16 17 18 19 20 21 22 23 24 25 26 75" 300" or Two 12'-6" Section End Section 300" or Two 12'-6"
Bol FEATURES: SPECIFICATIONS: 8' 24' Round Tapered and Straight Wood Poles STRUCTURA INC. FIXTURE TYPE: PROJECT NAME:
Bol 8' 24' Round Tapered and Straight Wood Poles FIXTURE TYPE: PROJECT NAME: Round Taper Glulam solid wood and aluminum pole available in 8' 24' lengths. Tenon adapters, slip fitters and side bracket mounts
SECTION CHAIN LINK FENCING AND GATES AND SOFTBALL BACKSTOP
1 1 1 0 1 0 1 0 1 SECTION 1 1 CHAIN LINK FENCING AND GATES AND SOFTBALL BACKSTOP BASED ON DFD MASTER SPECIFICATION DATED /01/ P A R T 1 - G E N E R A L SCOPE The work under this section shall consist of
Midwest Roadside Safety Facility
28 Spaces @ 75"=175'-0" 100'-0" 3:1 Cut 40'-0" 6'-3" (TYP.) 3:1 Soil Cut 3:1 1 2 3 4 5 6 7 8 9 10 25 12 13 11 14 15 16 17 18 19 20 21 22 23 24 25 26 6'-3" 25'-0" or Two Section 12-gauge End Section 25'-0"
Bike Locker Model DBL1 & DBL2
Bike Locker Model DBL1 & DBL2 DBL1 & DBL2 are constructed of 99% recycled steel and is available in 20 standard powder coat colors or a galvanized finish. DBL1 & DBL2 store 1 or 2 bikes effortlessly and
Superstrut Stainless Steel Channels and Accessories
In this section... Superstrut Stainless Steel Channels and Accessories Superstrut Stainless Steel Channels and Accessories Channels...46 Channel Fittings and Hardware...47 49 Clamps and Hangers...50 52
DOCUMENT SUBMITTAL REQUIREMENTS FOR A NEW MULTI-FAMILY DWELLING
INFORMATION BULLETIN / GENERAL INFORMATION REFERENCE NO.: None DOCUMENT NO. P/GI 2014-007 Previously Issued As: P/GI 2011-007 Effective: 01-01-2014 Revised: DOCUMENT SUBMITTAL REQUIREMENTS FOR A NEW MULTI-FAMILY
SPECIFICATIONS FOR THE INSTALLATION OF CONDUIT SYSTEMS IN RESIDENTIAL SUBDIVISIONS. Notification of Completed Conduit Sections
SPECIFICATIONS FOR THE INSTALLATION OF CONDUIT SYSTEMS IN RESIDENTIAL SUBDIVISIONS Section 1 Definitions 2 Scope of Work 3 Extent of Work 4 Inspection and Performance of Work 5 Trenching 6 Duct Installation
This specification describes the minimum requirements for structural steel drawings.
1/7 1.0 PURPOSE This specification describes the minimum requirements for structural steel drawings. 2.0 GENERAL As stated in specification SPEC-0800, drawings are intended to be Design drawings. Sufficient
SECTION CONCRETE REINFORCEMENT FOR STEAM UTILITY DISTRIBUTION
PAGE 032015-1 SECTION 032015 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification sections,
Deck Evaluation Checklist
Date: Reported By: Project Name/Client: Year Deck was Built: I. Stairs A. Not Applicable B. Are there any visible signs of cracks, decay or over-notching? No Yes 1. If yes, where? C. Stairway width: (Hint:
Spiral Slide
IMPORTANT Page 1 PLEASE READ THESE INSTRUCTIONS BEFORE COMMENCING ASSEMBLY. All equipment must be installed in accordance with these instructions. Check your shipment against Bill of Lading and Parts list.
UPM 10X and 10XHD A. TEE SOCKET: 7 O.D. PIPE SOCKET TO FIT OVER 6 SCHEDULE 40 OR 80 STEEL PIPE
Page 1 of 8 UPM 10X and 10XHD A. TEE SOCKET: 7 O.D. PIPE SOCKET TO FIT OVER 6 SCHEDULE 40 OR 80 STEEL PIPE B. CROSS PIECE: 3 X 3 X 3/16, LENGTH IS 60 (10X) or 78 (10XHD), SQ. TUBE 2 PLACES C. LONGITUDINAL:
.1 Applicability: These criteria shall be applied as follows:
DESIGN CRITERIA DIVISION 4800 STREET LIGHTING 4801 GENERAL: These criteria shall be adhered to for the design of all publiclyfinanced or privately-financed traffic signal systems to be installed in the
Ultra Space Saver American Bicycle Security Company
The Ultra Space Saver is userfriendly and allows easy access to bikes. It provides convenient space for u-lock security on nearly any bike, including bikes with fenders and fork shocks. The double-sided
SunTrackerTwo Preparation
TOLL FREE:(888)29-2705 FAX:(941)77-9460 info@eco-smart.com SunTrackerTwo Preparation Cutting Holes and Preparing Curbs T.G.I Or Truss CIRALIGHT INSTALLATION MANUAL Page 1 Cutting Holes and Preparing Curbs
SECTION SITE FURNISHINGS FOR CFCRT. 1. American Society for Testing and Materials (ASTM).
PART 1 - GENERAL 1.1 SECTION INCLUDES A. Benches. B. Trash receptacles. C. Bike storage. 1.2 REFERENCE STANDARDS A. Including but not limited to: 1. American Society for Testing and Materials (ASTM). 1.3
CHAPTER 29 PROJECT COMPLETION DOCUMENTS
CHAPTER 29 PROJECT COMPLETION DOCUMENTS PROJECT COMPLETION Upon completion of traffic control signal system and lighting projects, there are forms and checklists to ensure that the project is closed out
CITY OF BEVERLY HILLS Department of Public Works and Transportation Civil Engineering Division STREET/ALLEY IMPROVEMENT PLAN REVIEW CHECKLIST
CITY OF BEVERLY HILLS Department of Public Works and Transportation Civil ing Division STREET/ALLEY IMPROVEMENT PLAN REVIEW CHECKLIST The following checklist consists of the minimum requirements for preparation
HOW TO BUILD A DEER OR ELK-PROOF FENCE. Saskatchewan Environment Resource Stewardship Branch 112 Research Drive Saskatoon, Saskatchewan S7K 2H6
HOW TO BUILD A DEER OR ELK-PROOF FENCE Saskatchewan Environment Resource Stewardship Branch 112 Research Drive Saskatoon, Saskatchewan S7K 2H6 Revised March 2005 1 This information is intended to assist
10x10 Trellis Pergola
0x0 Trellis Pergola ASSEMBLY GUIDE Ver.-007 Table of Contents PAGE 0x0 Trellis Pergola Introduction & Overview...................................................... Pergola Materials Overview..............................................................
1. Show the following information with additional information necessary to indicate shop compliance with the requirements of this section.
SECTION 12360 LIBRARY SHELVING PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 06100 - Carpentry. 2. 09200 - Metal Studs, Lath, Suspension Ceiling, Plaster and Stucco. 3. 09660 - Resilient Tile Flooring.
SUBSTATION SECURITY WALL INSTALLATION MANUAL
SUBSTATION SECURITY WALL INSTALLATION MANUAL JULY 26, 2016 OLDCASTLE PRECAST, INC. 3000 New McEver Rd, Acworth, Ga 30101 Substation Security Wall Installation Manual This Installation Manual is intended
HOENER ASSOCIATES INC. ARCHITECTS
HOENER ASSOCIATES INC. ARCHITECTS BRUCE D. DELL MARK REUTHER ADDENDUM NO. 1 PROJECT 15-22C RENOVATION AND SITE WORK AT: BUILDING B DDRB OF ST. CHARLES DEVELOPMENT DISABILITIES RESOURCE BOARD ST. CHARLES,
H HD Adult Wheelchair Swing Frame & Hangers(perm) IMPORTANT
Page 1 IMPORTANT PLEASE READ THESE INSTRUCTIONS BEFORE COMMENCING ASSEMBLY. All equipment must be installed in accordance with these instructions. Check your shipment against Bill of Lading and Parts list.
EXCAVATION AND BACKFILL
Standard Specification 2565.3, 2451, and 1805 A basic understanding of specifications is needed to properly replace the disturbed soil and restore the condition of the excavated area. The size of the disturbed
Maintenance of Traffic sequence of operations including any phasing and detour maps;
All Local-let projects are required to have a Stage 2 submittal to the LPA Manager for review. The only exceptions are 2-lane resurfacing, striping, guardrail, and raised pavement markers, unless otherwise
SECTION STEEL LIGHTING STANDARDS. 1. Electrical conduit and fittings; Section
02760-1 of 5 SECTION 02760 STEEL LIGHTING STANDARDS 02760.01 GENERAL A. Description Steel lighting standards shall include, but not necessarily be limited to, furnishing and installing steel lighting poles,
Open Up Your View With CABLE SYSTEMS
Open Up Your View With CABLE SYSTEMS PRESENTED BY CROWN HERITAGE Our Cable Multiple options to accomodate any deck or stair design Marine Grade 316 stainless steel Swaging is the term used for attaching
BVS Cable support systems
Installation manual BVS Cable support systems Installation method Additional products Industriveien 29, 2020 Skedsmokorset, Norway BVS CABLE SUPPORT SYSTEMS Content Page no. Description 3-11 BVS Additional
Pole Mount Installation Manual
Pole Mount Installation Manual Thank You for Choosing AIMS Power! 1. AIMS Power is a leading supplier of solar products, specializing in PV mounting systems. We ensure our products are manufactured to
Installation Instructions
Column & Beam Units with Debris Netting Installation Instructions Laminated Wood Systems, Inc. Seward, Nebraska 800-949-3526 2015 LWS, INC. AVR-NET INSTALL 05-12-16 AVR Installation Notes 1 Safety The
Porta-Cleanse TM 4610/4620 Mastless Mixer Stand
Porta-Cleanse TM 4610/4620 Mastless Mixer Stand Issued: 11/00 Porta-Cleanse TM 4610/4620 Mastless Mixer Stand Issued: 9/04 4610/4620 Mixer Product Specification for Porta-Cleanse TM Mastless Mixer Stand
METALWORKS Concealed. Installation Instructions
METALWORKS Concealed Installation Instructions 1. GENERAL 1.1 Product Description MetalWorks Concealed ceilings consist of perforated and unperforated panels that are downward accessible, and are designed
10x10 Trellis Pergola
0x0 Trellis Pergola ASSEMBLY GUIDE Ver.0-7 Table of Contents PAGE Introduction & Overview...................................................... Pergola Materials Overview..............................................................
Project Booklet. Structural Drafting with AutoCAD
Project Booklet Structural Drafting with AutoCAD Introduction 1 General Setup 2 Border and Title Block 3 Drafting the Foundation Plan (Plate 1) 8 Drafting the South Elevation (Plate 2) 11 Drafting Section
CASS TL-3 (Utilizing C-Shaped Post) Assembly Manual
CASS TL-3 (Utilizing C-Shaped Post) Assembly Manual Part No. 620289B Revision March 2007 INDEX Page Important Notice 3 Introduction 3 General Description 3 Ground Preparation and Barrier Alignment 3 Layout
Original Gallery System
GAllery System Art Displays Original Gallery System a Gallery System product Here s everything you need to know to get started with your Gallery System Art Hanging System GS getting started To install
Installation Instructions
Installation Instructions Ceiling Mount Bracket for DLP Based Projectors (for High Ceilings) Model No. ET-PKD100H Contents Important Safety Notice.................. 2 For DLP Based Projector: PT-D10000
Standard Details Index NWTP Improvements and MF System Installation
Detail Standard Details Index NWTP Improvements and MF System Installation Marco Island, Florida Description 0315-001 PLASTIC WATERSTOP 0315-003 HYDROPHILIC/GROOVE WATERSTOP 0315-011 WATERSTOP JOINT 0315-154
Storefront Installation Guide
Storefront General Notes: 1. Check Contract Documents and Shop Drawings. Understand and clarify any Field Verify Notes and approvals of drawings and products to be familiar with the project. Installation
Section 808. FENCING
808.01 Section 808. FENCING 808.01. Description. This work consists of providing and erecting, or moving existing, woven wire fence, temporary fence, protective fence, chain link fence, high-tensile wire
3616 Old Howard Co. Airport Road Big Spring, TX
3616 Old Howard Co. Airport Road Big Spring, TX 79720 432.263.3725 SKT-350 SKT-350 31 Bill of Material Type I SKT MGS Type II SKT MGS S3000 1 SKT Impact Head S3000 1 SKT Impact Head Steel Post Systems
Post & Rail. Includes: Crossbuck, 2-Rail, 3-Rail and 4-Rail POST SUPPORT OPTIONS
Post & Rail Includes: Crossbuck, 2-Rail, 3-Rail and 4-Rail STAGGER RAIL ENDS FOR GREATER STRENGTH ALLOW 1-1/2" GAP ON HINGE SIDE OF GATE AND 1-1/4" ON LATCH SIDE OF GATE HARDWARE DIG HOLES 30" MINIMUM
Low Headroom Rear Mount TorqueMaster
Low Headroom Rear Mount Supplemental Instruction Insert This supplemental installation instruction is to be used as a supplement to the main Installation Instruction and Owner s Manual provided with the
ULTRA SPACE SAVER Installation Instructions
Installation Instructions The Ultra Space Saver has several steps for installation. Note that the single and double sided setups and parts are different. Make sure you follow the instructions according
Transmission Line Support Systems
Antenna Support Bracket for transmission line The Antenna Support Bracket angle mounts directly to a 4-1/2" (114 mm) OD antenna pipe mount or tower leg. This is ideal for supporting transmission line runs
AUXILIARY FRAMING AND ACCESSORIES
CUSTOM CABINETS & RACKS STRUT AND ACCESSO- RIES JUNCTION KITS ANGLE AND BRACE KITS SPLICE KITS BRACE KITS INSTALLATION KITS WALL ANGLE KITS RUBBER END CAPS SUPPORT INSTALLATION AND SUPPORT KITS STANCHION
How To Measure Your Finished Opening
3000 Series Bifold Doors How To Measure Your Finished Opening MEASURE FROM RIGHT TO LEFT 2 PLACES (WIDTH) MEASURE FROM TOP TO BOTTOM 2 PLACES (HEIGHT) Tools Required for Assembly: Tools Needed: Phillips
General Guidelines:
ASSEMBLY INSTRUCTIONS Congratulations on your new Patriot Dock purchase. This manual contains instructions to assemble basic dock configurations for use at typical residential shoreline application. Please