Hobart EZ-TIG 165i. Eff w/lk330301j And Following For OM Revision A And Following. 230 Volt 60 Hz TIG Only TM F. Processes.

Size: px

Start display at page:

Download "Hobart EZ-TIG 165i. Eff w/lk330301j And Following For OM Revision A And Following. 230 Volt 60 Hz TIG Only TM F. Processes."

Stephanie Harper
5 years ago
Views:

1 TM F Processes TIG (GTAW) Welding 20 Volt Arc Welding Power Source Hobart For OM Revision A And Following 20 Volt 60 Hz TIG Only File: TIG (GTAW)

2 SECTION 10 PARTS LIST FOR LK001J AND FOLLOWING C Figure Main Assembly Figure Main Assembly Wrapper, Label, Warning General Precautionary Static Cord Set, 250v 6 50p 12ga /C 7ft Spt Jkt (Prior tomc191006j) CORD SET,250V 6-50P 12GA /C 7FT SPT- JKT (Eff W/MC191006J) Hose, Nprn Brd No 1 X.250 ID X TM Page 42

3 Figure Main Assembly (Continued) GS Valve, 24VDC 2way Custom Port 1/8 Orf W/Frict (Prior to MD140022J) GS Valve, 24VDC 2way Custom Port.054 Orf W/Frict (Eff w/ MD140022J) Bushing, Strain Relief.240/.510 ID X.875 Mtg Hole CB Supplementary Protector, Man Reset 1p 5A 250VAC Panel, Rear (Prior to MB080009J) Panel, Rear (Eff w/mb j) Nut, 750 NPT 1.1 Hex.27 H Nyl Blk Ftg, Hose Brs Barbed M /16 Tbg X 5/8 18 Thrd (Prior to MC490002J) Handle, Carrying Hose, Gas 12 Ft W/Clamps (Prior to MC490002J) Hose, Gas 12 Ft W/Fittings (Eff w/mc490002j) Regulator/Flowmeter, 0 50 CFH Argon/CO2 Kit (Prior to MC490002J) Regulator/Flowgauge, 0 50 CFH AR/CO2 mix w/filter (Eff w/mc490002j) L Inductor, Input (Prior to MB J) L Inductor, Input (Eff w.mb j) Windtunnel, Assembly (see Figure 10-2) Grommet, Scr No 8/10 Panel Hole.12 Sq.500 High PC Circuit Card Assy, Control & Interface FM Fan, Muffin 24VDC 4500 Rpm 240 Cfm Mtg Holes Plenum, Air Base Bumper, RBR.875 OD X.188 ID X.9 High Recessed Cable Assy, RJ S Switch, Tgl Spdt 15A 125VAC On none on Spd Term Blk Nut, Hex.09 H Brs Blk Use w/switches Nut, Nylon Strain Rlf Pg thk 1.062od Work Cable, W/Clamp (12 ft) Torch Pkg,12.5 Ft (.8m), Rubber Blank, Snap in Nyl Mtg Hole Black D/D Knob, Pointer Dia Nut, Hex.25 H Nyl Flange.62 D Nameplate, Hobart EZ TIG 165I (Order By Model And Serial ) Panel, Front (Prior tomc191006j) Panel, Front (Eff w/mc191006j Nut, Nylon Thd Pg S Switch, Tgl Dpst 40A 600VAC Scr Term (Prior to MC191006J) S Switch, Rocker DPST 15A 250VAC Off-None-On (Eff w/mc191006j) P Pot Assy, W/Leads & Connector & Leds Cp Flat 1t T Inductor, Arc Starter/Output 150 Amp PC Circuit Card Assy, Arc Starter CE L Inductor, Toroid 5 Amp 180 Uh, 12 Leads W/Quick Con Insulator, Washer Inductor Label, Warning Electric Shock/Exploding s RFCS RJ45 Foot Control (Includes) RFCS RJ45 Foot Control (Pedal Only) Cable, w/connectors 14 Ft Clamp, Stl Cush.187 Dia X.281 Mtg Hole Zinc Pld When ordering a component originally displaying a precautionary label, the label should also be ordered. To maintain the factory original performance of your equipment, use only Manufacturer s Suggested Replacement s. Model and serial number required when ordering parts from your local distributor. TM Page 4

4 Hardware is common and not available unless listed B Figure Windtunnel Assembly Figure Windtunnel Assembly (Figure 10-1, 15) PC Circuit Card Assy, Commutator Control Bushing, Snap-In Nyl Stand-Off Panel, Midplane T XFMR, Main (Includes) RT Thermistor, NTC 10K 25 Deg C In Lead Heat Sink, Secondary Assy (See Figure 10-) Z Inductor, Output When ordering a component originally displaying a precautionary label, the label should also be ordered. To maintain the factory original performance of your equipment, use only Manufacturer s Suggested Replacement s. Model and serial number required when ordering parts from your local distributor. TM Page 44

5 Hardware is common and not available unless listed Figure 10-. Heat Sink, Secondary Assembly A Figure 10-. Heat Sink, Secondary Assembly (Figure 10-2, 7) Heat Sink, Secondary D9,D Diode, Ultra-Fast Recovery 90 A 600 V Dual SOT Q2,,4, Transistor, IGBT 100 A 600 V SOT RT Thermistor, NTC 0K 25 Deg C 8 In Lead Screw, M4.7 x 8.5 Pan HD-PHL STL PLD Sems Split/Fl SR Diode, Power Module 55 Amp 600 V 1 PH Fast Recovery... 1 To maintain the factory original performance of your equipment, use only Manufacturer s Suggested Replacement s. Model and serial number required when ordering parts from your local distributor. TM Page 45

6 Hobart Brothers Co. An Illinois Tool Works Company 2200 Corporate Drive Troy, OH 457 USA For Assistance: Call ORIGINAL INSTRUCTIONS PRINTED IN USA 2014 Hobart Brothers Co

DIVERSION 165 And DIVERSION 180 w/auto-line

TM-246 522C 2011 0 Processes TIG (GTAW) Welding 20 Volt Arc Welding Power Source DIVERSION 165 And DIVERSION 180 w/auto-line Diversion 165 And 180 Models Eff w/ma080041j And Following For OM-246 522 Revision