Explanation Drawings of Counterweights Assembly

Transcription

1

2

3 Explanation Drawings of Counterweights Assembly (1) At first, make bend lines on the template and then cut the center of the cutting lines as much as possible. (2) Do not immediately apply paste. Check the completed shape of the paper craft by folding the mountain and valley lines on the template. (3) Check that where should be the first place to paste together to make your work easier. Then start pasting the required parts together. Hole for Putting and Taking Out Weight Adjustment Material (Coin, Eraser, Etc.) Apply paste inside here and make a double fold. This part is to be pasted to the inside of the counterweight. So the paste area becomes the front side. (4) Put the hook for attaching and detaching the counterweights to the counterweights. Do this before assembling the counterweights or putting the lid on the upper side because it makes your work easier.

4 Explanation Drawings of Left and Right Crawlers Assembly (1) As same as other templates, make bend lines on the template before cutting out it. (2) Cut the cutting lines on the template correctly. (3) Make folds and assembly the template before applying paste. At this time, check that where should be the first place to paste together to make your work easier. Then paste the required parts together. Fold Inside Here Right Fold Inside Here Left Apply paste to the front side of the lower shoe and apply paste to the back side of the upper shoe. The completed crawler will be put together with the extension and retraction part in the next page. Be careful not to mistake the left part for the right part and vice versa.

5 The inside is a sliding portion, so apply paste to the outside to prevent unevenness. Explanation Drawings of Left and Right Crawlers extend and retract part Aseembly The inside is a sliding portion, so apply paste to the outside to prevent unevenness. (1) This page explains the procedures to make the part for extending and retracting the crawler. After it is completed, it will be put together with the crawler made at the previous page. (2) Make bend lines on the template and then cut the cutting lines correctly. (3) Make folds and assembly the template. Right Left The right sliding portion of the extension and retraction part is smaller than that of the left. The left sliding portion of the extension and retraction part is bigger than that of the right. The right sliding portion is put into the left sliding portion and then extension and retraction is carried out.

6 Explanation Drawings of Carbody and Carbody weight Assembly (1) The carbody makes the each part for extending and extracting the left and right crawlers made at the previous page together. Furthermore, this page explains the procedures to make the carbody weight, which can be attached or detached to the carbody. (2) Make bend lines on the template and then cut the cutting lines correctly. (3) Make folds and assembly the template. Paste 4 places to the inside similarly. Carbody Side-Swing unit Paste the cylinder to the bottom. The upper hole prevents rocking.

7 Explanation Drawings of Carbody base Assembly Paste Left Guard Here (1) The cab, guard, and attachment, etc. will be placed on this carbody. (2) Make bend lines on the template and then cut the cutting lines correctly. (3) Make folds and assembly the template. Paste Attachment Mount Here Paste Cab and Right Guard Here Paste Upper Cylinder Lower Cylinder Carbody base Upper side-swing unit Clearance Paste the cylinder to the back side of the upper side. Do not paste the portion of lower hole and be sure to leave a little clearance. The lower cylinder passes through this clearance and reaches to the back of the upper side.

8 Explanation Drawings of Boom tip and Hook Assembly Boom tip-a The hole is provided to put the string for the hook easily. (1) The boom can be disassembled to the upper, inter, and lower boom. (2) Make bend lines on the template and then cut the cutting lines correctly. (3) Make folds and assembly the template Paste Boom tip-b Here Paste Boom tip-b Here This part is little bit narrowed because this will be inserted to the inter boom. Paste the left and right paste tab after folding the template to the center.

9 Explanation Drawings of Boom insert and Boom base (1) This page explains the procedures to make the inter and boom base. (2) Make bend lines on the template and then cut the cutting lines correctly. (3) Make folds and assembly the template. This part will be attached to the attachment base. Do not fold inside. This part is little bit narrowed because this will be inserted to the inter boom.

10 Explanation Drawings of Gantry, Spreader, and Tension Member Assembly Upper spreader (1) This page explains the procedures to make the gantry, and spreader, etc. (2) Make bend lines on the template and then cut the cutting lines correctly. (3) Make folds and assembly the template. Lower spreader If this slit is not here, folding is impossible. Past the thin triangle pole first This part will be attached to the gantry Boom back stop Bend the thin triangle pole during work. This part will be attached to the gantry Tension member This cut is provided for folding. Make cuts after pasting this part as a pole because it makes your work easier. Leave one face uncut. Make the thin tension member first and then make the large tension member by rolling it around the thin tension member. It will help to make smooth sliding movement. This part will be attached to the attachment base Paste the part to be attached to the base by rolling it around the boom back stop. Adjusting the tightness o f t h e r o l l b e f o r e pasting it will help to make smooth sliding movement. This part will be attached to the attachment base

11 Explanation Drawings of Attachment Mount Assembly This is the place to install the tension member. Attachment Mount This is the place to install the foot of the gantry. This is the place to install the boom back stop. (1) This page explains the procedures to make the base to install the boom base, gantry, and tension member, etc. (2) As same as other templates, make bend lines on the template and then cut the cutting lines. (3) Make folds and assembly the template. This is the place to install the lower boom. Hole for Paper Craft Work Hole for Paper Craft Work This is used for retracting the folded tension member. Make cuts and fold little bit to the inside.

12 Explanation Drawings of Whole Paper Craft Assembly Paste the mount for attachment, etc Insert this claw to the back side of the slit. The part without the piece of paper here is larger, so insert this first. Paste the cab. The part with the piece of paper here is smaller, so insert this later. This is the completed crawler and undercarriage. The left and right crawlers slide and it changes the width. Paste this to the gantry. Paste the foot of the gantry and foot of the tension member and paste upper part of them together. These cuts are provided for retracting the folded tension member. Fold the cuts inside little bit. Paste the boom base to the mark. Insert other booms at the time of last procedure, which is stretching of the kite string. Place the knot inside. This is the last procedure. Stretch the kite string through the spreader and hook. Place the knot inside Place the swing body base on the undercarriage. The cylinder at the back side of the swing body is made little bit smaller than the cylinder of the undercarriage. When inserting it, turning it will help to insert it smoothly. Paste the boom base and boom back stop together and then paste each of them to the attachment base. Paste the lower spreader to the upper side of the gantry as it moves up and down. Only pass the kite string through the lower side. Make the knots at the inside of both sides. Only pass the kite string through. Paste the left machine room. This makes the hole for paper craft work unseen. Insert the claws of counterweights to the slits of the body. If balancing of the weight is necessary, adjust it by putting or taking out a coin or eraser, etc. to or from the inside hole. Completed Paper Craft