GrowSpan Series 500 Automated Ridge Vent Kits

Transcription

1 GrowSpan Series 500 Automated Ridge Vent Kits Photo shows a sample ridge vent as installed on a greenhouse. Actual building and ridge vent length may differ Growers Supply All Rights Reserved. Reproduction is prohibited without permission. GS05KRV20A GS05KRV24A GS05KRV36A GS05KRV48A GS05KRV60A GS05KRV72A GS05KRV84A GS05KRV96A 1

2 Important Information LOCATION Observe these precautions: Install ridge vent so prevailing winds flow over the covered side of the vent and not into the open vent. READ THIS DOCUMENT BEFORE YOU BEGIN Thank you for purchasing the ridge vent kit. When properly assembled and maintained, this product will provide years of reliable service. These instructions include helpful hints and important information needed to safely assemble and properly maintain the vent. Please read these instructions before you begin. If you have any questions during the assembly, please contact customer service for assistance. SAFETY PRECAUTIONS Wear eye protection. Wear head protection. Wear gloves when handling metal parts. Use a portable GFCI (Ground Fault Circuit Interrupter) when working with power tools and cords. Do not climb on the frame during or after construction. NEVER hang items from the vent! Do not occupy the structure during high winds, tornadoes, or hurricanes. Provide adequate ventilation if the structure is enclosed. Do not store hazardous materials in the structure. Provide proper ingress and egress to prevent entrapment. Prevailing Wind Direction Check area above the building for power lines. Do not install the vent when power lines are present over the assembled building. Location should be away from structures that could cause snow to drift on or around the building. Drifting snow can damage the ridge vent frame and film. Do not position the structure where large loads such as snow and ice, large tree branches, or other overhead obstacles could fall. Always check local building codes before you begin and follow codes as instructed. WARNING: The individuals assembling this vent are responsible for designing and furnishing all temporary bracing, shoring and support needed during the assembly process. For safety reasons, those who are not familiar with recognized construction methods and techniques must seek the help of a qualified contractor. DOUBLE-LAYER FILM INSTALLATION Structures equipped with a double-layer film include a layer that is Infra Red (IR) Retention film. IMPORTANT! During cover installation, install the IR film first! Examine the film and install it according to the instructions printed on the film. Consult list of building materials to determine if your building is equipped with a double-layer cover. 2

3 Important Information ASSEMBLY PROCEDURE Following the instructions as presented will help ensure the proper assembly of the vent. NOTE: Once the main frame of the building is assembled, install the ridge vent. To better understand overall building design and position of the vent on the frame, review all technical documents before you begin. The steps outlining the basic vent frame assembly are as follows: 1. Verify that all parts are included in the shipment. Notify Customer Service for questions or concerns. 2. Read this guide and all additional documentation included with the shipment before you begin. 3. Gather the tools, bracing, ladders, lifts, and assistants needed to assemble and install the ridge vent on top of the assembled building frame. 4. Check the weather before you install the roof cover and any end panels (if equipped). Do not install covers or panels on a windy or stormy day. 5. Attach the Z144 polylatch u-channel/slam rail components to the end rafters, main frame, and ribbon board (if present) as instructed in the building assembly guide. NOTE: Some fabric end panels wrap around the end rafters and are anchored to the back of each end rafter during installation. If the end panel for your building is installed in this manner, assemble the end wall frame and install the fabric end panel or panels before attaching the Z144 u-channel/slam rail to the tops of the end rafters. For buildings with polycarbonte panels, consult those instructions for important information regarding the installation of the Z144 u-channel/slam rail. 6. Install the ridge vent after the main building frame is assembled and before the roof film installation. 7. After installing the ridge vent frame, return to the main building instructions and continue. This applies to covers that stretch over the frame assembly. 8. Complete and return all warranty information as instructed if present. REQUIRED TOOLS The following list identifies the main tools needed for assembly. Additional tools and supports may be needed depending on the structure, location, and conditions. Tape measure or measuring device and marker to mark locations on the pipes and rafters. Variable speed drill and impact driver. (A cordless with extra batteries works best.) Metal-cutting saw or tool to cut pipe. Wrenches and impact socket set, hammer, and gloves. Adjustable pliers and self-locking pliers. 4mm Hex wrench to tighten set screws Ladders, work platforms, and other machinery for lifting designed to work safely at the height of the building. Safety equipment to protect head, eyes, hands and feet. UNPACK AND IDENTIFY PARTS The following steps will ensure that you have all the necessary parts before you begin to assemble the shelter frame. 1. Unpack the contents of the shipment and place where you can easily inventory the parts. Refer to the Bill of Materials/Spec Sheets. 2. Verify that all parts listed on the Bill of Materials/Spec Sheets are present. If anything is missing or you have questions, consult the Pictorial Parts Guide and all diagrams for clarification, or contact Customer Service. NOTE: You do not need to open the plastic bags containing smaller parts such as fasteners or washers. 3

4 Important Information PICTORIAL PARTS GUIDE The following graphics and photos will help identify the different parts of the vent system. Each component has a specific position on the vent and building frame. To better understand how to assemble the vent system components, review this guide before you begin. Consult the bill of materials for specific component information. IMPORTANT NOTE ABOUT SKU/PART NUMBERS: Vent systems are available in many widths and lengths. Consult the diagrams for your vent system during assembly to position the different profiles correctly. Connecting the different components in the incorrect order will cause misalignment with other components. Review diagrams carefully before assembly. ALWAYS INSTALL THE DIFFERENT VENT COMPONENTS IN THE POSITIONS SHOWN ON THE DIAGRAMS FOR YOUR VENT SYSTEM AND BUILDING! Vent Bearing Plate Vent Rack Drive FA2902 & FA Vent Window Connector Vent Rack Curved Weather-Stripping Vent Motor* Vent Rack Straight *Actual motor may differ in size and design. Vent Rack Vent systems typically use one of the rack designs shown. Consult the bill of materials for the rack used for your vent system. (The rack drive is sold separately.) 4

5 Assembly Steps This guide presents photos and diagrams to help in the assembly of the ridge vent. The availability of lifts, assistants, and other factors all affect ridge vent assembly. The same vent can be assembled in different ways. With this in mind, this guide does not present a step-by-step procedure. The best way to assemble the ridge vent components is determined by the contractor on site. For best results, review all the information in this guide before you begin. The procedure below outlines one way to assemble the ridge vent. WARNING: To prevent damage and possible injury, use straps to secure a covered vent to rafters during assembly. Never allow a covered vent to remain unsecured or detached from the drive motor. Basic Steps: 1. Attach ridge vent arms (PGRVA0500G17S35) and bottom rail sections (111612Z144) by working from one end to the other. Consult Quick Start Guide (back of this document) diagrams. ATTENTION: Be sure to position vent arm on the correct side of the rafter as shown in diagrams near the back of this guide. Holes for vent arms and vent window connector brackets (111681) are drilled during assembly. CABLES: When installing ridge vent arms at each end of the building frame, review the Connection Details Views 1 and 2 for cable bracket (108503) positions. Cables are installed at each end of the ridge vent. Consult View 3 (Connection Details) to properly secure the splice of separate bottom rails. See also Additional Connections Photos. 2. Attach vent window connectors (111681) to the bottom rails. See page 20 diagrams for hole locations. 3. Assemble and install cables at each end of the ridge vent frame. (See View 5.) Tighten cables as needed to square the ridge vent frame. Frame is square when corner-to-corner measurements are the same. See photo at bottom of page 6 and the Close-Up View (page 21) for examples. 4. Attach slam rail (111613Z144) to the building frame. Consult the procedure on page 12 to install slam rail. 5. Attach u-channel and flashing to the ridge vent arm at each end of the vent frame. See pages Attach motor, motor mount bracket, drive axle, and related drive components. Use the 131S075 (1.315" x 75") swaged pipe for the drive axle. Secure each axle splice using an FA4482B Tek screw. During the axle assembly, be sure to slide vent rack drives (111679) onto the axle before securing pipe joints with Tek screws. Consult the photos for additional information when completing this step. ATTENTION: Do not allow drive axle ends to touch the inside surface of either end wall. See photos on pages 8 and 10. For easier assembly, attach chain drive components to motor drive sprockets before attaching the motor to the installed motor mount bracket. 7. Install vent racks and secure to vent window connectors attached to the bottom rail (111612Z144). Tighten vent rack drive set screws. See Additional Connection Photo pages near the back of this guide. 8. Attach weather stripping (111983) to underside of flashing at each end of vent frame. 9. Test vent operation. Examine drive motor for manual drive screw that can be used by attaching a hex bit to a drill. Insert bit end into manual drive of motor and test operation. 10. Consult documentation sent with the motor to properly connect power to motor. Enlist the services of a qualified electrician to properly wire the motor to power. 11. Return to and continue with the main building instructions (if applicable). 5

6 Install Ridge Vent Install ridge vent framing before installing the roof film. Consult the technical documents for vent to better understand assembly steps. Photos below show a few ridge vent details. Photo shows a sample building with an installed ridge vent in the open position. Do not install Z144 rail here at each end. Attach the Z144 rail to the top of the end rafters after installing the fabric end panels if equipped. Rail is included with the building. IMPORTANT: When attaching the slam rail Z144 to end rafters, do not install in the area where vent opening is located. See dashed line above. Photo shows inside view of ridge vent as seen from the ground looking up. Install vent cables at each end of the ridge vent only. Use the cables to square the vent frame on the building frame. Tighten until cables are snug. Consult the ridge vent technical documents for additional cable installation details. 6

7 Install Ridge Vent INSTALL RIDGE VENT (continued) Ridge Vent Arm Ridge Purlin Rafter Ridge Vent Bottom Rail Z144 Ridge Vent Bottom Rail Splice (S125P006) Vent Rack ATTENTION: Vent racks are either curved or straight depending on the application. A curved vent rack is shown in this example. It may differ from the actual vent rack sent with your vent package. Secure bearing plates to the rafters using FA4482B Tek screws. Secure bottom rail splices using FA4482B Tek screws. Ridge Vent Bottom Rail Vent Bearing Plate

8 Install Ridge Vent INSTALL RIDGE VENT (continued) Graphics below show attaching the u-channel and flashing to the top of the curved ridge vent arm using FA4482B Tek screws. Attach components to the curved ridge vent arm at each end of the assembled vent frame. Cut to length as needed. Drive screws through the u-channel and flashing and into the vent frame bow. Space Tek screws evenly at 12" on-center. ATTENTION: Photos below show the installation of the u-channel. If you vent includes the flashing, review the diagrams on the next page before you attach the u-channel. Install flashing between u-channel and vent arm. 8

9 Install Ridge Vent INSTALL RIDGE VENT (continued) U-Channel Flashing Diagram shows flashing and u-channel attached to the top of one end bow of vent frame. 9

10 Install Ridge Vent INSTALL RIDGE VENT (continued) U-Channel and Flashing installed at each end of the vent. Curved Ridge Vent Arm Underside of Flashing Circled area shows the greenhouse vent window connector (111681) as attached to the roof vent bottom rail. Consult the technical diagrams supplied with the vent for fastener details. See also the photos near the end of this guide. See diagrams and notes on page 20. Roof Vent Bottom Rail Slam Rail Vent Drive Axle Roof vent slam rail as attached to the top of the rafters. Attach using two FA4482B Tek screws at each rafter. Drive axle for vent constructed using 1.315" diameter pipe. Secure each pipe splice with FA4482B Tek screws Vent Rack Drive Do not allow ends to contact inside surface of end wall cladding. 10

11 INSTALL RIDGE VENT (continued) Install Ridge Vent ATTENTION: Consult the technical documents at the back of these instruction for motor installation details. Attach mounting plate using FAG363B bolts, FALB04B nuts, and FAME08B washers. Slam Rail Slam Rail Mounting Plate Motor ATTENTION: Position motor at (or near) the center of the drive shaft. Slam rail for vent runs length of vent frame and is attached to rafter tops. Rail is installed after main vent frame is assembled. Photo shows vent motor installed in a greenhouse. View from inside greenhouse. 11

12 Install Ridge Vent INSTALL RIDGE VENT (continued) Slam Rail Z144 Bottom Rail Z144 NOTE: Vent shown in open position. Photo above shows completed ridge vent as seen from inside the building. Review these steps to install the slam rail. 1. During the assembly, complete the hinged section of the ridge vent frame first. This is the portion of the vent that opens and closes. 2. After constructing the main vent assembly, close the vent so the bottom rail (111612Z144) is tight against top of building rafters. Check connections at each rafter for conflicts between frame components. Adjust as needed. 3. Mark the position of the bottom rail on each rafter for reference. 4. Locate slam rail sections (111613Z144) needed to create a rail as long as the building. 5. Using the marks on the rafters as guides, attach the slam rail sections (111613Z144) to the top of the rafters using two FA4482B Tek screws at each rafter. Measure and cut the final slam rail section to length if needed. ATTENTION: Bottom rail (111612Z144) of vent will sit on top of slam rail as shown in the technical diagrams sent with ridge vent. Attach film cover in lower channel of slam rail during film cover installaion. ROOF VENT BOTTOM RAIL RIDGE VENT ARM ROOF VENT SLAM RAIL RAFTER 12

13 Install U-Bolts and Tighten Vent Rack Drive INSTALL VENT RACK U-BOLTS Vent rack u-bolts prevent the vent from opening too far and tracking out of the vent rack drives. After the ridge vent is assembled and attached and before the cover film is installed, install the u-bolts. There are two u-bolts for a typical ridge vent system. Attach one u-bolt to the vent rack closest to the gearbox and the remaining u-bolt to a vent rack near the end of the vent frame. Set u-bolts 10"-12" from the end of each rack. 1. With vent closed, take an FA2906 u-bolt and slide it over the free end of the rack. Choose rack closest to installed gearbox. 2. Add one (1) FA2902 u-bolt plate and two (2) FALB01B nuts. 3. Using a 1/2" wrench, tighten the nuts until snug. 4. Move to another rack and repeat these steps to attach the u-bolt. 5. With the vent closed, return to each vent rack drive (111679) and tighten the two (2) set screws using a 4mm hex wrench. 6. Test vent operation. See Step 4 on page 5. Vent should open freely and smoothly. 7. Close the vent and read the care and maintenance information on the next pate. 8. Return to the main building assembly guide and continue as instructed. 13

14 Shelter Care and Maintenance CARE AND MAINTENANCE Proper care and maintenance is important. Check the following items periodically to properly maintain the shelter and installed ridge vent: Regularly check film cover to ensure it remains tight and in proper repair. Repair all tears and holes to prevent further damage. Inspect cover-to-ridge vent frame connections to ensure cover material remains locked in the u-channel. Replace all damaged or broken components immediately. Read all documentation included with motor to troubleshoot operation and maintain motor. Check connections and all fasteners to verify they remain tight and in good condition. Inspect vent drive components and test operation. Tighten any loose fasteners or set screws. Do not climb or stand on the building at anytime. Verify that side panel components (if equipped) are in good working condition. Replace curtain cords (if installed) and anti-billow rope immediately if worn or broken. Check operation of the air inflation systems (if equipped) to ensure hoses and fittings are tight and air pumps are working. Remove debris and objects that can accumulate on the building. Use tools that will not damage cover film when removing debris. Remove snow to prevent excess accumulation. Use tools that will not damage the cover when removing snow. Check shelter contents to verify nothing is touching cover or side panels to cause damage or wear. If shelter is dismantled and moved, inspect all parts and connections before using. For replacement or missing parts, call for assistance. Bearing Plate Rack Drive ASSEMBLY AND MAINTENANCE: During assembly apply a thin film of spray lubricant or light grease to the vent rack drive bearings and the vent bearing plate. Additionally, while in use, monitor operation and vent drive components. At approximately 4-6 month intervals, or sooner depending on use and environment, reapply lubricant in the same areas. Repair or replace any broken or worn components immediately. 14

15 Quick Start Guide ATTENTION: Vent drive assembly is not shown. Sample Ridge Vent Standard Lengths Actual building may differ from the example shown in this diagram. 15

16 Connections Ridge Vent VIEW 4 SLAM RAIL TO RAFTER CONNECTION VIEW 3 VENT BOTTOM RAIL SPLICE CONNECTION VIEW 5 CABLE ASSEMBLY VIEW 2 RIDGE VENT ARM TO BOTTOM RAIL CONNECTION VIEW 1 RIDGE VENT ARM TO RAFTER CONNECTION ATTENTION: Frame shown with ground posts. 16

17 Connection Details Ridge Vent NOTE: NUTS SHOULD BE TIGHTENED ON BOTH SIDES OF RAFTER. TIGHTEN DOUBLE-NUTS AGAINST EACH OTHER TO ALLOW 1/4" GAP FOR VENT ARM TO ROTATE FREELY. NOTE: ALL HOLES IN ALUMINUM TO BE FIELD DRILLED, SEE TOP VIEW DIAGRAM FOR LOCATIONS. - (2X) 1/4" X 3/4" HEX BOLT - (4X) 1/4" NUT - (2X) 1/4" WASHER RIDGE VENT ARM [PGRVA0500G17S35] VENT CONNECTOR [111681] CABLE BRACKET (NOTE: USED WHERE CABLE IS REQUIRED) ROOF VENT BOTTOM RAIL [111612Z144] ROOF VENT BOTTOM RAIL [111612Z144] - (4X) #14 X 1" TEK SCREW - (4X) 3/8" NUT - (4X) 3/8" WASHER - (1X) 1/4" X 2" HEX BOLT - (1X) 1/4" NUT - (1X) 1/4" WASHER RAFTER NOTE: RACK DRIVE [111680] RIDGE VENT ARM - (1X) 1/4" X 2" HEX BOLT - (1X) 1/4" NUT - (1X) 1/4" WASHER (1X) Splice Tube [S125P006] ROOF VENT BOTTOM RAIL [111612Z144] THREADED ROD [FAK36Z008] VIEW 1 RIDGE VENT ARM TO RAFTER CONNECTION VIEW 2 RIDGE VENT ARM TO BOTTOM RAIL CONNECTION VIEW 3 VENT BOTTOM RAIL SPLICE CONNECTION ROOF VENT BOTTOM RAIL [111612Z144] RIDGE VENT ARM ROOF VENT SLAM RAIL [111613Z144] RAFTER 1/2" TURNBUCKLE (104189) ROOF VENT SLAM RAIL [111613Z144] 1/4" CABLE (AR1060) - (2X) #14 X 1" TEK SCREW FIELD VERIFY SLAM RAIL LOCATION 1/4" THIMBLE (AS1084) 1/4" THIMBLE (AS1084) 1/4" CABLE CLAMPS (AS1004) RAFTER 1/4" CABLE CLAMPS (AS1004) 7/16" SHACKLE (AS2167) RAFTER GREENHOUSE DRIVE AXLE BEARING PLATE ROOF VENT SLAM RAIL [111613Z144 ] RACK DRIVE PINION ASSEMBLY [111679] - (2X) #14 X 1" TEK SCREW VIEW 4 SLAM RAIL TO RAFTER CONNECTION RACK DRIVE [111680] VIEW 5 CABLE ASSEMBLY 17

18 [D2] VIEW 3 DRIVESHAFT BEARING PLATE & RAFTER CONNECTION Connections Drive Shaft [D2] VIEW 1 GREENHOUSE RAFTER & MOTOR MOUNTING PLATE CONNECTION DETAIL [D2] VIEW 2 DRIVESHAFT SPLICE DETAIL 18

19 GREENHOUSE RAFTER CHAIN DRIVE COUPLING [111675] NOTE: ATTACH TO MOTOR BEFORE ATTACHING MOTOR TO INSTALLED MOUNTING BRACKET. Connection Details Drive Shaft CHAIN DRIVE COUPLING [111675] **NOTE: SAME HARDWARE APPLIES TO SPLICES OF SWAGED PIPE THROUGHOUT THE DRIVESHAFT SYSTEM. MOTOR [111676] - (2X) 5/16" X 2" HEX BOLT - (2X) 5/16" LOCKING NUT CHAIN DRIVE COUPLING [111675] - (2X) 3/8" X 3" HEX BOLT - (4X) 3/8" WASHER - (2X) 3/8" NUT NOTE: ATTACH TO MOTOR BEFORE AT- TACHING MOTOR TO INSTALLED MOUNT- ING BRACKET. MOTOR MOUNTING PLATE [ ] DRIVESHAFT [131S147] [D2] VIEW 2 DRIVESHAFT SPLICE DETAIL CURVED DRIVE RACK [111673] EXPLODED VIEW GREENHOUSE RAFTER BOW - (2X) #14 X 1-1/2" TEK SCREW DRIVESHAFT BEARING PLATE [111674] VENT RACK DRIVE [111679] DRIVESHAFT [131S147] [D2] VIEW 3 DRIVESHAFT BEARING PLATE & RAFTER CONNECTION ASSEMBLED VIEW [D2] VIEW 1 GREENHOUSE RAFTER & MOTOR MOUNTING PLATE CONNECTION DETAIL 19

20 TOP VIEW DRIVE RACKS LOCATED 7" FROM CENTERLINE OF RAFTER. AS SHOWN IN VIEW 2 NOTE: RIDGE VENT ARM TO BE INSTALLED TO THE INSIDE OF END RAFTER BAYS TO ACCOMMODATE CABLE Top View Showing Ridge Vent Position Rafter spacing of this sample building is 6' on-center. Actual building may differ. CABLE CABLE NOTE: BOTH EXTRUSIONS START/END AT THE CENTERLINE OF LAST RAFTER C L 5'-7" END ROOF BOWS ONLY C L 6'-0" TYP. C L 5'-7" END ROOF BOWS ONLY NOTE: FOR STRUCTURES WITH RAFTERS 4' ON CENTER, ALL SPACINGS OF RIDGE VENT ARMS AND DRIVE RACKS WILL BE REDUCED BY 2' FROM WHAT IS SHOWN 20

21 Closeup View of Ridge Vent Section ROOF VENT BOTTOM RAIL [111612Z144] ROOF VENT SLAM RAIL [111613Z144] SQUARE THE RIDGE VENT FRAME Dashed lines show where cables are located at each end of the ridge vent frame. Measure corner-tocorner when tightening the cables. Frame is square when these dimensions match. Square the ridge vent frame before you attach the slam rail to the building frame as described on Page

22 Inside View Showing Ridge Vent 22

23 Additional Connection Photos Use the photos on this page to properly connect two pieces of vent frame bottom rail. 1. Take one 125P006 splice tube and mark the center. Gently tap tube into the end of the bottom rail. Align center line with end of bottom rail. 2. Clamp tube to rail and secure using two FA4482B Tek screws. 3. Remove clamp add the second piece of bottom rail and tap into place to set against the first. 4. Secure with Tek screws. 1 Center Mark ATTENTION: There are four (4) Tek screws needed for each bottom rail splice. 23

24 Additional Connection Photos Attach weather stripping to the underside of the flashing at each end of the vent frame. Weather stripping will seal against rafter when vent is closed. Weather Strip Installation: After assembly, attach the weather stripping to the underside of the flashing at each end of the ridge vent. Weather stripping will help seal the ends of the vent when closed. See the dashed line in the photo above. 24

25 NOTES Space below is reserved for customer notes. 25