TYPE TS 320A ROTARY TABLE OPERATION MANUAL

Size: px

Start display at page:

Download "TYPE TS 320A ROTARY TABLE OPERATION MANUAL"

Mark Watts
5 years ago
Views:

1 TYPE TS 30A ROTARY TABLE OPERATION MANUAL

2 I. Usage Type TS-A Rotary Table is one of main accessories of milling machines.it can be fitted onto milling machine for the following works. I.Machining cuived surfaces utilizing circular milling..machining flat surface which is set at a certain angle to a given reference. 3.Inde:xing;drill.in or milling. It can also be used on drilling machine and slotting machine to perform one or several works mentioned above. The workpiece is clamped by the fixture which has been mounted on the table or directly clamped onto the table surface. II. Main Specifications and Parameters No. Items Type TS TS. TS TS TS TS TS 60A 00A 50A 30A 400A 500A 630A Diaof table(rnm) Taper of center bore(morse) No. No.3 No.3 No.4 No.4 No.5 No.5 3 Locating bore(diax depth)(mm) ct>5x6 ct>30x6 ct>30x6 ct>40x0 ct>40x0 ct>50x ct>50x 4 Width of T-slot(rnm) Included angles of adjacent T-slots ooo Driving ratio of worm gear :90 :90 :90 :90 :90 :0 :0 7 Module ofwormgear(mm) Graduations on the table circumference 360 ( per division) 9 Min.readout of hand wheel ' / \ 0 Min.readout of vernier 0" ill. Construction and Operation The operating positions are shown as following:..

3 .Dividing plate.sector 3.Locking handle 4.Spring sheet 5.Crank handle I e A(rnm) B(rnm) TS 60A TS TS 00A 50A TS TS TS TS 30A 400A 500A 630A Inserting pin for locating 7.Screw 8.Nut C(rnm) D(rnm) indirect dividing attaclunent Sketch for type TS-A rotary table. T-slot bolts 6.Locking handle for eccentric sleeve.0il hole 7.Directing collar for zero position 3.Sight glass for oil level 8.Graduated collar 4.Hand wheel 9.Vernier 5.Locking handle for table IO.Tightening screw / This type of rotary table is a manually-operated model. When the table is used for machining, the workpiece is clamped onto the table surlace with the aid of T-slots on the table face. For easy in mounting and aligning, simple in operating, loosen the locking.handle 6 of eccentric sleeve and then rotate directing collar 7 of zero position.in such a way, the table can be quickly rotated for a large angle. If rotate the directing collar 7 of zero position in opposite direction to engage the worm gear in mesh and tighten it by means of locking handle of eccentric sleeve 6, the indexing and continual machining can be proceeded by the hand wheel 4. For index-machining, the starting position is determined according to the position of aligneor given reference.after loosening the tightening screw 0, slowly move the directing vernier 9 to make the graduated line aligne with any graduation on the table periphery and then tighten the vernier 9 with the aid of locking screw 0 again. At the same time, rotate the graduated collar 8 which is set on worm to ensure the zero position aligne with zero line of directing collar 7. After reading the "degree"from the table periphery,loose the table and then index as a means of starting position from this"degree". The dividing plate set, or called as indirect dividing attachment,(supplied for special order) can be attached to the rotary table. when the dividing plate is used for dividing, remove nut 8, screw 7, hahdwheel 4, replaced them by the dividing plate set which consist of parts,,4,5 and 6. With the aid of four bolts(m4x6), the dividing plate is cormected with block of scale collar. To do this, the locking handle 3 must be locked. The sector must be finnly clamped onto the surlace of dividing plate by means of spring sheet 4.The numbers of hole circle and the included angle of sector ann are selected according to required divisions (see table for dividing). After having pulled out the locating pin 6, by turning the crank handle 5, continuous dividing can be done. N. Maintenance and Lubrication Care must be taken to protect all sliding and engaging surlace. The table and workpiece mounted on the table must not be impacted and knocked absolutly to protect its precision from... 3.

4 damage. After operating, all of the chips and coolant must be removed and the table face must be painted with oil to pi:event rust. Before putting it into use, unscrew the oil plug, fill oil to make sure that the worm and worm wheel are running in a good condition. The oil in the cavity of base should be changed once evecy half a year. Before evecy shift of operation, the oil hole of spindle must be filled with adequate oil by means of a oil gun. When filling, lubricated parts should be moved slightly in order to ensure satisfactory effect of lubrication TYPE TS 30 A ROTARY TABLE CERTIFICATE / Dia. of table:60, 00, 50, 30, 400, 500, 630 (mm) Serial No.:. 4.

5 Accuracy test record This rotary table has been tested and found to be in conformity with the technical standard of JB/' { ROTARY TABLE } and approved for deliv- Item No. Test to be applied Testing Sketch Tolerance (mm) ezy. on the length of Straighteness of table surface gauge block indicator base 300mm: 0.00 (no protrusion on table table surface center) 0.00 Axial run- (TS60A out of table TS500A) surface (TS630A) Parallelism on the between length 3 table surface of and bottom 300mm: surface

6 Item No. Test to be applied Testing Sketch Tolerance (mm) 4 5 Radial runout of axis of tapered center bore Total dividing error of rotary table for one complete b a Multilateral ;:insm Collrr.a tor a)0.0 b) " revolution.-.:;, TYPE TS 30 A ROTARY TABLE PACKING LIST. 8.

7 No Name Rotary Table T-slot Bolts Operation Manual Quant. Certificate Packing List 4. Handle (for TS60A.TS00A.TS50A.TS30A) (supplied for special order): Dividing plate set l 0.

8 Rel. No. Description Quantity Base Rel. No. Description Quantity Set screwl>l! 7 Table 8 Threaded pin 3 Taper sleeve 9 Block 4 Socket head bolt * 4 30 Dog point set screw 5 Table clamp 3 Worm shaft 6 a-ring 3 Key 7 Handle assembly 33 Dowel pin 8 Dog point set screw 34 Spacer 9 Hex nutl>l! 35 Lock nut 0 Washer* 36 Spacer with keyway Clamp 37 Eccentric sleeve L-Clamp 38 Fillister head screw 3 T-Bolt 39 Handle assembly \ 9 '4') Locating key Flllister head screw 3 Retaining piate Table nut 4 Vernier lockdown 4 Fillister head screw 8 43 Sleeve 44 Micro collar 4 Flllister head screw (or socket head bolt)* 40 Vernier collar 9 Ring 45 Collar 0 T-bolt 46 Handle wheel Knob 47 Handle Indicator Sight glass 0-ring Plug 48 Handle screw 49 Fillister head screw 4 50 Spacer 5 Hex nutl>l! 6 Handle Assembly l>l!standard hardware Item available locally. Replacement Parts illustration for Rotary Tables

9 ATTENTION(For TS, TSL, TSK Rotary Table) Dear customer : Before you moving you table, you should read the attention carefully. * Installation : the handlewheel of the table is lower than the base., when installing, should leave enough room for handwheel. Otherwise could bump the handwheel and result in destroying the worm shaft. Handwheel Installation surface *Adjusting mesh of worm gear The engagement of worm gear for all types rotary table has been adjusted to a good condition before delivery and customer must not adjust it. If the adjustment must be made because_ of worm gear is worn or for some reasons, the procedure is shown as following First loosen the handle a for eccentric sleeve locking, unscrew Locking bolt b, ()Screw clockwise limiting bolt a to add the mesh, at this time rotate the handle wheel to ensure the mesh of worm gear clockwise and counterclockwise within 6 and tighten the lockin bolt b, then clamp the handle a for eccentric sleeve locking. ()Screw counterclockwise limiting bolt a to reduce the mesh, at this time rotate the handle wheel to ensure the mesh of worm gear clockwise and counterclockwise within 6 and tighten the locking bolt b. Rotate indicate counterclockwise, when the bolt c touching the locating pin, the worm gear are disengaged. Rotate indicate clockwise, when the bolt d touching the bolt a, the worm gear is engaged. Limiting bolt a Bo! t d Base Worm Eccentric sleeve Bo It c Handle a for eccertic sleeve locking Eccentric sleeve Locking bolt b Handwb.eel Locating pin Locking handle b Indicator

Machines. 6/16 Kenworth Place, BRENDALE Ph Fx RT-060S. Horizontal / Vertical Rotary Table INSTRUCTION MANUAL

Machines. 6/16 Kenworth Place, BRENDALE Ph Fx RT-060S. Horizontal / Vertical Rotary Table INSTRUCTION MANUAL RT-060S Horizontal / Vertical Rotary Table INSTRUCTION MANUAL Horizontal / Vertical Rotary Table - Instructions There are three methods of setting positions using a rotary table. 1. Use the degree scale