3850, Drum & Disc Brake Lathes. Parts Identification
|
|
- Camron Hicks
- 6 years ago
- Views:
Transcription
1 3850, 3860 Drum & Disc Brake Lathes Parts Identification READ these instructions before placing unit in service. KEEP these and other materials delivered with the unit in a binder near the machine for ease of reference by supervisors and operators. Manual Part No.: HENNESSY INDUSTRIES INC. Manufacturer of AMMCO, COATS and BADA Automotive Service Equipment and Tools. Revision: 05/01
2 Table of Contents Mainframe Assembly Electrical Schematic Lathe Assembly Twin Cutter & Safety Sheild Drum Boring Bar Assembly (3860 ONLY) Crossfeed Assembly Parts Identification The following pages include full parts breakdowns with exploded view illustrations to help with ordering replacement or spare parts. Assemblies are noted where it is recommended that individual parts not be ordered separately. These parts are available only as assemblies because some parts are staked, pinned, or press fitted, then drilled, machined, or bored. Close tolerances must be maintained in assembly. Every effort is made to supply accurate exploded views, however, due to interim changes in manufacturing operations, some units may not be exactly as illustrated. AMMCO 3850, 3860 Brake Lathes 3
3 Mainframe Assembly *Not Shown - Motor Chipshield 3860 Only 4 AMMCO 3850, 3860 Brake Lathes
4 Mainframe Assembly Motor, Drive Mainframe Bar, Guide Sheave, Motor Screw, 1/4-20x.25 Hex Socket Head Cap Ring, Retaining, Internal Spacer Sheave, Spindle Key, Square Cover, Pulley Screw, 5/16-18x.5 Hex Flat Head Screw, 1/4-20 Flat Head Whiz Lock Spindle Cone, Bearing Cup, Bearing Nut, Adjusting, Spindle Bearing Ring, Lock, Spindle Bearing Lamp Assembly Power Cord Strain Relief Seal Tube, Protector, Rotor Feed Belt Fitting, Grease Cone, Bearing Cup, Bearing Seal Plate, Serial Screw, Drive Screw, 8-32x1 Slot Fillister Head Bolt, Eye Switch, Lamp Dust Boot Draw Bar Electrical Schematic Power Cord Drive Motor Work Lamp On/Off Switch Slide Motor AMMCO 3850, 3860 Brake Lathes 5
5 Lathe Assembly 6 AMMCO 3850, 3860 Brake Lathes
6 Lathe Assembly Pin Washer Crossfeed Boot & Retaining Ring Assembly Lead Screw Boot & Retaining Ring Assembly Wiring Harness, 3-Wire Black Screw, 8-32 Unc x.38 Hex Washer Head Wiring Harness, 4-Wire Cap Plug, Protect Tube Bolt, T-Slot, 1/ Nut, Self-Alignment Wiring Harness, 3-Wire Red Caution Card Electrical Panel Switch Strain Relief Cap, End, Crossfeed Mainframe Assembly Crossfeed Assembly Twin Cutter Assembly, Pos. Rake (3850) Twin Cutter Assembly, Neg. Rake (3860) Clamp, Boring Bar, Top Clamp, Boring Bar, Bottom Holder, Tool Bit (3850) Screw, Sq. Hd. Set (3850) Boring Bar Assembly (3850) Knob, Lock Screw, 3/8-16 Flt. Pt. Set Nut, Jam Gib, Crossfeed AMMCO 3850, 3860 Brake Lathes 7
7 Twin Cutter & Safety Shield Drum Boring Bar Assembly (3860 ONLY) 8 AMMCO 3850, 3860 Brake Lathes
8 Twin Cutter & Safety Shield *Carbide Insert, Pos. Rake (3850) **Carbide Insert, Neg. Rake (3860) Screw, 4-40x.25 Oval Head *Holder, Toolbit, RH, Pos. Rake (3850) *Holder, Toolbit, LH, Pos. Rake (3850) **Holder, Toolbit, RH, Neg. Rake (3860) **Holder, Toolbit, LH, Neg. Rake (3860) Screw, Sq. Hd. Set Toolholder, LH Toolholder, RH Nut Shield Bracket Screw, Thumb Screw Spacer Washer Housing, Twin Cutter Screw, Set Knob, Dial Rod Dial, Micrometer Washer, Spring Plug, Dial Rod, Dial Screw, 3/16-16 Set Plug, Dot Screw, Locating Nut, Hex Spring Gib, Tool Holder Knob, Lock Denotes Safety Shield Assembly items * 3850 ** 3860 Drum Boring Bar Assembly (3860 ONLY) Bar, Tool, RH, Assembly Screw, Oval Hd, Machine Bit, Carbide (Pkg./2) Holder Sleeve Spring Compression Washer, Flat Screw, Shoulder Bar, Boring Ring, Retaining, External Washer, Wave Dial, Micrometer Rod, Dial Screw, Set, Cup Point Dial, Depth AMMCO 3850, 3860 Brake Lathes 9
9 Crossfeed Assembly Screw from motor AMMCO 3850, 3860 Brake Lathes
10 Crossfeed Assembly Crossfeed Slide, Drum Nut, Slide, Drum Locknut Knob, Lock Plug, Brass Gib, Slide, Tool Screw, 5/16-24 UNF x Screw, 5/16-24 UNF Soc Hd Cap Fan, Slide Motor Handle Assembly, Drive Motor Engagement Bracket, Drive Motor Pin, Groove, Drive Lock Screw, 8-18x1.25 Socket Hd Cap Shaft, Spline Gear, Miter Gear, Driven Gear, Drive Screw, Lead Bushing, Bronze, Oil Impregn Race, Thrust Bearing, Thrust Coupler Assembly Bushing, Bronze, Oil Impregn Screw, Lead, Rotor Feed Race, Thrust Bearing Thrust Collar, Bearing Handwheel Assembly Ball,.25 Steel Spring Cover, Crossfeed, Bottom Screw, 8-18 Hex Washer Head Self Tapping Cover, Chip, Bottom Cover, Top, Chip Cover, Drum Slide Nut Plug, Expansion Wiper, Tool Slide, LH Wiper, Tool Slide, RH Cord, Pigtail Strain Relief Washer Bushing 49 Electrical Tape Plug, Copper Set Screw, Hex Socket Head Motor, Slide Ring, Wiper Pin, Roll Strip, Cover, LH Shield, Dial, Handwheel Screw, 8-32x.500, HX Soc, Bin HD Cover, Assembly, Dovetail, LH Plug, Dome AMMCO 3850, 3860 Brake Lathes 11
11 /01 Copyright 2001 Hennessy Industries and AMMCO All Rights Reserved Printed in USA
3000, 4000, 4100, 7500, 7700
3000, 4000, 4100, 7500, 7700 Drum & Disc Brake Lathes s Identification READ these instructions before placing unit in service. KEEP these and other materials delivered with the unit in a binder near the
More information3000, 4000, 4100, 7500, 7700
3000, 4000, 4100, 7500, 7700 Drum & Disc Brake Lathes Model 4000 Shown s Identification READ these instructions before placing unit in service. KEEP these and other materials delivered with the unit in
More information3000, 4000, 4100, 7500, 7700 Drum & Disc Brake Lathes
3000, 4000, 4100, 7500, 7700 Drum & Disc Brake Lathes Model 4000 Shown Parts Identification READ these instructions before placing unit in service. KEEP these and other materials delivered with the unit
More informationEEBR312A Brake Lathes Parts Identification
EEBR312A Brake Lathes s Identification READ these instructions before placing unit in service. KEEP these and other materials delivered with the unit in a binder near the machine for ease of reference
More information700/705/710. Vehicle Mounted Brake Lathe & Rotor Driving Unit. Parts Identification
700/705/710 Vehicle Mounted Brake Lathe & Rotor Driving Unit READ these instructions before placing unit in service. KEEP these and other materials delivered with the unit in a binder near the machine
More information6000, Heavy Duty Drum/Disc Lathe. Parts Identification
6000, 6002 Heavy Duty Drum/Disc Lathe Parts Identification READ these instructions before placing unit in service. KEEP these and other materials delivered with the unit in a binder near the machine for
More information535A. Main Components. Pipe and Bolt Threading Machine. Printed in U.S.A. Ridge Tool Company/Elyria, Ohio, U.S.A.
Pipe and Bolt Threading Machine A Main Components 0 Screw, Button Head /" - 0 x /" () Washer, Flat /" ()" Top Cover 0 Base Bottom Cover Screw, Pan Head # - x " () Carriage Assembly 0 Front Support Bar
More information12. Mechanical Drawings & Parts Breakdown List
12. Mechanical Drawings & Parts Breakdown List Note: When ordering parts, please be prepared with, 1. Machine model & serial number. 2. Item number. 3. Part number and description. 4. Year of Production.
More information535-Manual. Main Components. Pipe and Bolt Threading Machine. Printed in U.S.A. Ridge Tool Company/Elyria, Ohio, U.S.A.
Pipe and Bolt Threading Machine -Manual Main Components 0 Screw, Button Head /" - 0 x /" () Washer, Flat /" ()" Top Cover 0 0 Cutter Assembly Stop Pin 0 Pin Reamer Assembly Carriage Assembly 0 Stop Screw
More informationSECTION 9: PARTS. Electrical REF PART # DESCRIPTION REF PART # DESCRIPTION
SECTION 9: PARTS Electrical 1 P4002001 START BUTTON 52 P4002052 CONTACTOR GSC1CJX4-D 110V 2 P4002002 INDICATOR LIGHT 53 P4002053 CONTACTOR JZC3-40D 110V 3 P4002003 JOG BUTTON 54 P4002054 FUSE HOLDER 4
More informationParts Catalog. S-Series Slicer Manual Frozen Option S13. Model:
, 07 995 ECN 08 Parts Catalog S S-Series Slicer Manual Frozen Option Model: S 05/0/07 Rev. G IMPORTANT! TO EXPEDITE SHIPMENT OF PARTS, ALWAYS SPECIFY MODEL, REV, PART NUMBER, AND SERIAL NUMBER OF UNIT.
More information1822-I. Spindle Assembly. Pipe and Bolt Threading Machine. Ridge Tool Company/Elyria, Ohio, U.S.A. 2* 3 4 5* * *
-I Pipe and Bolt Threading Machine Spindle Assembly * * * 0 * * * 0 * * 0* * * Rear Cover * Screw () * Washer () Top Cover w/clips (Includes,, ) * J Clip () Front Cover * Screw () Pivot Rod Support ()
More informationSECTION 9: PARTS Column Breakdown
SECTION 9: PARTS Column Breakdown 3 4 5 6 7 8 12 2 1 9 10 11 20 21 13 14 15 18 16 17 25 26 27 28 29 3 31 31-1 32 33 34 35 36 37 39 38 47 48 46 45 3644 44 43 40 41 42 24 23 22 52 51 50 30 49 57 58 59 60
More informationREAD THIS FIRST. For questions or help with this product contact Tech Support at (570) or
READ THIS FIRST Model G0728-31 ***IMPORTANT UPDATE*** For Machines Mfd. Since 01/17 and Owner's Manual Revised 09/14 For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com
More informationOperating Instructions and Parts Manual Step-Pulley Turret Mill Model JVM-836
Operating Instructions and Parts Manual Step-Pulley Turret Mill Model JVM-836 JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-690036 Ph.: 800-274-6848 Revision C 11/2014 www.jettools.com
More informationREAD THIS FIRST. For questions or help with this product contact Tech Support at (570) or
READ THIS FIRST Model G4002/G4003 ***IMPORTANT UPDATE*** For Machines Mfd. Since December, 2014 and Owner's Manual Printed April, 2014 For questions or help with this product contact Tech Support at (570)
More informationSECTION 9: PARTS. Headstock A 126A 127A-1 REF PART # DESCRIPTION REF PART # DESCRIPTION
SECTION 9: PARTS Headstock 120 121 113 115 112 111 110 109 108 105 106 107 135 101 119A 121 120 118 114 115 107 106 104 123 122 118 114 126A 105 126 103 102 126B 127A-1 131 127A 124 133 134 126C 129 130
More informationSPARE PARTS LIST MODEL NO. LB1200F PAGE 1 ITEM PART NO. DESCRIPTION QTY NOTE
PAGE 1 001 JM21000018 HEX.SOCKET HEAD SCREW M5X12 4 002 JM21000019 SPRING WASHER 5 4 003 JM21000020 FLAT WASHER 5 4 004 JM21000021 UP COVER COMPLETE 1 005 JM21000025 MICRO SWITCH FIX PANEL A 1 006 JM21000026
More informationSECTION 9: PARTS Headstock Case and Shift
SECTION 9: PARTS Headstock Case and Shift 3 1 2 10-1 10-2 8 9 10 6 7 19 10-3 15 11 12 25 16 17 18 14 13 12 32 26 29 20 21 33 34 27 35 37 28 43 22 38 39 40 31 45 28 43 23 41 5 28 43 44 30 36-80- Model G0709
More informationBASE, COLUMN, ARM AND TABLE
SPARE S LIST Item No. 700000 Article No. 84-2265 IMPORTANT INSTRUCTIONS It is most important that the above illustration be studied prior to the assembly of the saw blade and arbor or the assembly of the
More informationCATALOG OF REPLACEMENT PARTS
CATALOG OF REPLACEMENT PARTS FMS20 MIXER WITH ATTACHMENT HUB ML-134387 ML-134388 WITHOUT ATTACHMENT HUB ML-134398 ML-134399 FORM 43166 (September 2016) F-43166 (September 2016) - 2-2016 Table of Contents
More informationNumber Wheeler P/N Description Set Rex P/N Notes Base 1 J Support, Right 1 J Support, Left 1 J Nut (M8)
1 603500 Base 1 J001 2 603501 Support, Right 1 J002 3 603502 Support, Left 1 J003 4 600328 Nut (M8) 4 5 600130 Spring Washer (8mm) 4 6 600344 Roll Pin (M6x30) 4 7 600129 Socket Hd Cap Screw (M8x25) 4 8
More informationTire Chain Kit. Replacing Shear Pins. Weight Kits. Drift Cutter
Replacing Shear Pins The augers are secured to the spiral shaft with two shear pins and cotter pins. If the auger should strike a foreign object or ice jam, the snow thrower is designed so that the pins
More informationParts Catalog. S-Series Slicer Smart Manual SG13. Model:
, 07 99507 ECN 065 Parts Catalog S-Series Slicer Smart Manual Model: SG SG 0/0/07 Rev. G IMPORTANT! TO EXPEDITE SHIPMENT OF PARTS, ALWAYS SPECIFY MODEL, REV, PART NUMBER, AND SERIAL NUMBER OF UNIT. GLOBE
More informationSERVICE PARTS LIST PAGE 1 OF 6 BASE ASSEMBLY SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 12" SLIDING COMPOUND MITER SAW
PAGE 1 OF 6 BASE ASSEMBLY 00 0 CATALOG NO. EXAMPLE: SPECIFY CATALOG NO. AND NO. WHEN ORDERING PARTS 6955-20 1 02-80-0050 Thrust Bearing (1) 2 05-80-0510 M5 x 12mm Flat Head T-20 Screw (5) 3 05-81-0135
More informationHD38, HD58, HD78 REV
HD38, HD58, HD78 REV. 07.29.2014 COVER for HD38, HD58, HD78 5 P004868 1/4-20x3/4 Button Head Cap Screw Stainless Steel 2 6 P001450 Lockwasher - Internal Tooth.250 6 8 P005200 Wave Disc Washer 4 10 P004869
More informationMain Drive Components
Pipe and Bolt Threading Machine Main Drive Components 0 0 Rear Centering Head Centering Jaw Set Spiral Pins () 00 Centering Scroll Retaining Ring 0 Rear Bearing 0 Oil Ball Valve () # - x / Screw Motor
More information488 PARTS LIST 1 3 SCREWS FOR NO. 2 2 FLYWHEEL CAP 3 FLYWHEEL 4 END NUT FOR NO. 10 5 BALL BEARING FOR NO. 3 (1 st ) 6 BALLBEARING FOR NO. 3 (2nd) 7A CLUTCH RACE KEY 7B CLUTCH RACE 7C CLUTCH SPRING 7D 7
More informationGEAR HEAD METAL LATHE
GEAR HEAD METAL LATHE MODEL G4002 / G4003 PARTS LIST COPYRIGHT 2000 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF
More informationMain Breakdown. Model G0531B/G0566B V2 (G0531B) 80V2-2
Main Breakdown 53 85-1 54 59 54 56 54 52 55 57 175 53 56 85 29 119-2 114 89 22 119-2 119 107 119-5 119-3 119-6 119-1 29 22 119-4 114 112 96 113 114 100 116 117 105 120 102 103 108 115 99 98 92 91 90 73
More informationSAVE THIS MANUAL FOR FUTURE REFERENCE. WARNING: To reduce the risk of
- ($ 0$$/ PP-,( /$( WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Part SP SAVE THIS MANUAL FOR FUTURE REFERENCE Printed in Taiwan
More informationSECTION 9: PARTS. Accessories
SECTION 9: PARTS Accessories 2 1 1-1 1-2 3 4 39 138 35 135 40 34 33 7 6 401V2 36 36-3 36-2 28 29 30 27 26 31 32 25 22 24 23 16-21 15 14 10 11 9 13 12 36-1 37 38 1 P4003G0001 4-JAW INDEPENDENT CHUCK ASSEMBLY
More informationMODEL NO.: MI PARTS BREAKDOWN
MODEL NO.: MI-76350 PARTS BREAKDOWN MAGNUM DRILL PRESS ASSEMBLY INSTRUCTIONS MODEL MI-76350 Before you begin to assemble your drill press, review the parts breakdown and keep it ready for reference. Start
More informationRP-VE416FS/FSD VE416FS and VE416FSD Roll Grooving Tools
PARTS ORDERING INFORMATION When ordering parts, the following information is necessary for Victaulic to process the order promptly: 1. Tool Model Number VE416FS or VE416FSD 2. Tool Serial Number The Serial
More informationSECTION 9: PARTS. Accessories
SECTION 9: PARTS Accessories 2 1 1-1 1-2 3 4 39 138 35 135 40 34 33 7 6 5 401V2 36 36-3 36-2 28 29 30 27 26 31 32 25 22 24 23 16-21 15 14 10 11 9 13 12 36-1 37 38 1 P4003G0001 4-JAW INDEPENDENT CHUCK ASSEMBLY
More informationSECTION 9: PARTS Stand/Brake/Coolant Pump
SECTION 9: PARTS Stand/Brake/Coolant Pump 8-1 18 3 4 2 8 7 20 6 5 19 7 1 17 23 42 22 21 25 24 31 62 26 27 29 28 30 55 5 56 57 32 33 66 60 61 63 64 22 9 54 53 2 10 10 2 11 10 16 9 58 10 67 10 34 65 35 36
More informationSECTION 9: PARTS. Accessories 2-1
SECTION 9: PARTS Accessories 2-2 3 1 1-3 1-1 2 2-1 5 12 1-2 13 11 31 10 9 7 6 4 15 8 14 19 20 21 23 24 28 29 30 18 17 16 25 27 1 P0750G0001 3-JAW CHUCK ASSEMBLY 6" D1-5 SCROLL 13 P0750G0013 DRL CHK KEY
More informationColumn & Stand. -4- Model G0759 (Mfd. Since 1/14)
Column & Stand 3 4 5 6 7 8 12 2 1 9 10 11 20 21 13 14 15 18 16 17 25 3 26 27 28 29 31 31-1 32 33 34 47 46 45 3644 48 35 36 37 39 43 44 42 38 40 41 412 24 23 22 52 51 50 30 49 412-2 412-1 57 58 39 59 60
More informationJ-3-D PART NO DATE:
37-380 & 37-877 8 PROFESSIONAL JOINTER J-3-D PART NO. 909563 DATE: 05-12-04 Page1/ J-3-D /DEB REPLACEMENT PARTS * 1345487 CUTTERHEAD ASSY, INCL: 1 1340196 KNIFE SCREW 2 1345488 BAR 3 37-355 KNIVES (SET
More informationSERVICE PARTS LIST PAGE 1 OF 6 BASE ASSEMBLY SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 12" DUAL BEVEL COMPOUND MITER SAW B27B
PAGE 1 OF 6 BASE ASSEMBLY 00 0 EXAMPLE: Component Parts (Small #) Are Included When Ordering The Assembly (Large #). SPECIFY CATALOG NO. AND NO. WHEN ORDERING PARTS = Part number change from previous service
More informationMODEL RA-2500N RADIAL ARM SAW
1 6130089 HEX. NUT (L.H.T.) W5/8"-18UNF 2.18 2 6900549 WASHER 1.78 3 6080529 ARBOR COLLAR 31.02 4 6760117 OILLESS METAL 1.57 5 9270612 CLAMP SCREW M6 X 12 0.19 6 9220625 HEX. SOCKET HEAD BOLT M6 X 25 0.22
More informationSPARE PARTS LIST MODEL NO PAGE 1 ITEM PART NO. DESCRIPTION QTY NOTE
PAGE 1 001 342186-7 SWITCH PROTECTOR 1 002 911118-1 PAN HEAD SCREW M4X12 6 003 155512-9 SWITCH PLATE 1 004 651757-2 SWITCH ABK266 1 006 685712-2 SPONGE SHEET 60X60 1 007 911118-1 PAN HEAD SCREW M4X12 1
More informationHow to program the digital speed display (This is factory set and will only need to be programmed if the unit is replaced)
How to program the digital speed display (This is factory set and will only need to be programmed if the unit is replaced) 1. Press and hold the set button (top left corner) until the display shows Fun
More informationWELDING POSITIONER PARTS BREAKDOWN DRAWING GP-200
WELDING POSITIONER PARTS BREAKDOWN 10 DRAWING GP-200 1 GP-200-001 FRAME 1 2 GK-160-012 5/16"-18UNC x 5/8" CARRIAGE BOLT 6 3 GK-136-055 5/16"Ø LOCK WASHER 6 4 GK-109-052 5/16"-18UNC HEX NUT 10 5 GP-200-002
More informationPARTS G9729 Lathe Bed
PARTS G9729 Lathe Bed 114 132 126 125 131 133 129 128 130 127 139 124 10 124 123 122 135 137 147 144 121 148 146 149 136 138 140 150 152 142 143 141 151 153 21 168 20 19 18 17 162 22 147 13315 14 13131
More informationDi-Acro 18E Stylus Turret Punch Press
OPERATOR S MANUAL & INSTRUCTIONS Di-Acro E Stylus Turret Punch Press Di-Acro, Incorporated PO Box 00 Canton, Ohio Progress Street N.E. Canton, Ohio 0 0-- 0--00 (fax) Revised 0/0 Sale or distribution of
More informationST1014 PARTS ST1014 Headstock Breakdown
ST1014 PARTS ST1014 Headstock Breakdown 112 114 23 104 105 108 102 106 20 19 21 22 101 100 103 111 38 14 15 37 46 44 47 45 107 93 39 41 40 67 110 109 74 75 76 11 12 13 9 8 6 10 31-2 31-3 3 2 7 26 24 31-1
More informationPage 1 Parts List for AL-51G (L160) 07/08/201. Headstock Assembly
Page 1 Parts List for AL-51G (L160) 07/08/201 Headstock Assembly 1--------1002-------------------Headstock Casting 13-------1012------------------------------Nut M28 2--------1006---------------------------Flange
More informationOperation and Maintenance Instructions Geared Head Bench Lathe Models GHB-1340A, GHB-1440A
Operation and Maintenance Instructions Geared Head Bench Lathe Models GHB-1340A, GHB-1440A (GHB-1340A shown with optional stand 321443AK) For Parts List and Electrical Diagrams, see document M-321357A
More informationHR24TS Rotary Rake. Serial Numbers less than Illustrated Parts Breakdown. Curtain & Guards, Front
HRTS Rotary Rake Serial Numbers less than 00 Illustrated Parts Breakdown Page Page Page Page Page Page Page Page Page Page Page Page Tongue Front Frame Front Axle Curtain & Guards, Front Front Pivot Bridge
More informationRYOBI 10 in. TABLE SAW - MODEL NO. BT3000
FOR MITER TABLE ASSEMBLY, REFER TO FIGURE 0 RYOBI 0 in. TABLE SAW - MODEL NO. BT000 FIGURE 5: 0 in. TABLE SAW FOR BLADE GUARD ASSEMBLY, REFER TO FIGURE FOR RIP FENCE ASSEMBLY, REFER TO FIGURE FOR MOTOR
More informationSECTION 10: PARTS. Headstock
33 32 31 30 7 SECTION 10: PARTS 34 23 36 22 15 14 12 35 37 48 39 41 42 50 40 25 38 38 26 39 42 44 41 25 26 40 51 43 52 10 5 53 9 4 1 27 2 21 19 20 Headstock 8 16 11 17 18 14 13 7 6 45 47 46 3 1 P0768001
More informationCATALOG OF REPLACEMENT PARTS
CATALOG OF REPLACEMENT PARTS HL300 SERIES LEGACY MIXER ML-134351 ML-134358 ML-141097 HL300 HL300C HL300 (Canada) A product of HOBART 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 FORM 43136 Rev. C (July 2017)
More informationSection A Gear Box September A
Section A Gear Box September 06 1A Index 1. 1-10016-000 Gear Box Oil Pan. 1-100486-000 Clutch Lever Assembly, See Page 9A for breakdown. 1-1004-000 Clutch Cam, for all A machines prior to Serial #5 1-104-000
More informationSECTION 9: PARTS Main
SECTION 9: PARTS Main 58 63 67 66 65 67 66 59 58 49 58 48 49 61A 61 64 62 55 50 35-3 34 35-1 57 56 41 42 151 51 50 33A 35-2 30A 30A-1 35 38 39 31 32 18 40 43 44 68 51 41 45 46 57 56 55 47 152 153 20 21
More informationHeadstock Assembly 31
Headstock Assembly 31 Parts List: Headstock Assembly Index No. Part No. Description Size Qty 1... 6294736...Faceplate...3... 1 2... 6295796...Nyloc Insert Socket Set Screw...1/4-20x3/8... 4 3... 6294725...Spur
More information25-200H. 12 Planer / Jointer. with Helical Cutterhead. Parts List.
25-200H 12 Planer / Jointer with Helical Cutterhead 4001824 Parts List www.rikontools.com CABINET ASSEMBLY PARTS EXPLOSION & PARTS LIST KEY NO. DESCRIPTION KEY NO. DESCRIPTION 1 Pan Head Screw M6x12 P25-200H-1
More informationCATALOG OF REPLACEMENT PARTS
The Choice of Experience CATALOG OF REPLACEMENT PARTS MODELS 909A 919A 909E 919E 909M 919M SLICERS EFFECTIVE MARCH 2009 - 2 - Table of Contents 5 ELECTRICAL COMPONENTS (909A & 919A) 7 ELECTRICAL COMPONENTS
More informationCATALOG OF REPLACEMENT PARTS
CATALOG OF REPLACEMENT PARTS HS4N SLICER ML-136338 HS4N A product of HOBART 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 FORM 43311 (August 2015) F-43311 (August 2015) - 2 - HOBART 2015 Table of Contents
More informationRYOBI 10 IN (254 MM) TABLE SAW MODEL NO. BT REPAIR SHEET
RYOBI 0 IN (2 MM) TABLE SAW MODEL NO. BT00- REPAIR SHEET 2 RYOBI 0 in. (2 mm) TABLE SAW - MODEL NO. BT00- FOR MITER TABLE ASSEMBLY, REFER TO FIGURE B FOR BLADE GUARD ASSEMBLY, REFER TO FIGURE E FOR RIP
More informationExploded View Saw Base - Model 7060 Semi-Automatic Cut-Off Band Saw
Exploded View Saw Base - Model 7060 Semi-Automatic Cut-Off Band Saw 136 137 135 134 132 131 133 113 114 115 117 116 118 119 120 121 79 78 77 107 108 65 76 110 109 66 10 9 6 11 5 4 8 7 75 74 73 72 111 112
More informationSection D ACCELERATOR
Section D ACCELERATOR December 2009 1D Index 1. 47-021476-001 Ball Accelerator Box 2. 11-051019-001 Hex Hd. Cap Screw (10 mm x 25 mm) 3. 11-052018-001 Flat Washer (10.5 mm) 4. 47-021249-004 Ball Cushion
More informationThese are tricks or tips I use when working on a Mill These are intended for informational purposes only and not responsible for any injury or damage to the machine Removal of motor on a variable speed
More informationModel G " Planer/Moulder -33- G0477 Body Breakdown
Model G0477 15" Planer/Moulder -33- G0477 Body Breakdown 202 200 201 203 204 194 192 193 195 205 141 143 196 197 142 148 146 178 183 154 155 198 199 144 145 153 157 159 158 181 182 188 185 184 187 186
More informationSECTION 10: PARTS. Headstock
33 32 31 30 7 SECTION 10: PARTS 34 23 36 22 15 14 12 35 37 48 39 41 42 50 40 25 38 38 26 39 42 44 41 25 26 40 51 43 52 10 5 53 9 4 1 27 2 21 19 20 Headstock 8 16 11 17 18 14 13 7 6 45 47 46 3 1 P0768001
More informationSERIES I MILLING MACHINES
INSTALLATION, OPERATION, MAINTENANCE, AND PARTS LIST SERIES I MILLING MACHINES TP5260 Revised: August 29, 2005 Manual No. M-450 Litho in U.S.A. Part No. M -0009500-0450 June, 2003 MAINTENANCE PROCEDURES
More informationCATALOG OF REPLACEMENT PARTS
CATALOG OF REPLACEMENT PARTS FMS30 MIXER ML-134462 ML-134463 FORM 43181 Rev. A (April 2014) F-43181 Rev. A (April 2014) - 2-2014 Table of Contents 5 CONTROL PANEL 7 ELECTRICAL COMPONENTS 9 ATTACHMENT HUB
More informationM1014 7" x 12" Metal Cutting Bandsaw PARTS -38-
14 13 15 16 18 17 55 10 12 11 19 54 9 20 53 7 5 4 60 7 3 1 28 6 2 61 23 27 26 29 21 24 25 22 32 32 33 35 36 37 38 49 48 47 40 39 34 30 59 51 52 46 45 44 43 42 42 41 50 56 57 58-38- Parts List 1 XM1014001
More informationParts Catalog. S-Series Slicer Smart Manual SG13. Model:
, 08 99507 ECN 065 Parts Catalog S-Series Slicer Smart Manual Model: SG SG /6/08 Rev. R IMPORTANT! TO EXPEDITE SHIPMENT OF PARTS, ALWAYS SPECIFY MODEL, REV, PART NUMBER, AND SERIAL NUMBER OF UNIT. GLOBE
More informationDisc, Belt, and Combination Disc/Belt Sanders
This Manual is Bookmarked Operating Instructions Parts Manual Disc, Belt, and Combination Disc/Belt Sanders Models: 4200A, 4300A, 4400A 4200A Disc/Belt Sander 4300A 6 Inch Belt Sander 4400A 12 Inch Disc
More informationOperating Instructions and Parts Manual Electronic Variable Speed Turret Mill Model JTM-1050EVS
Operating Instructions and Parts Manual Electronic Variable Speed Turret Mill Model JTM-1050EVS JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-690060 Ph.: 800-274-6848 Revision G1 06/2015
More informationSECTION 9: PARTS. Table & Column Breakdown
SECTION 9: PARTS Table & Column Breakdown Table & Column Parts List 201 P1126201 TABLE HANDWHEEL 230 P1005603 LIMIT STOP SLEEVE 205 P1126205 LEADSCREW ASSY M23.5-2.5 X 468 2121 P11262121 INDICATOR PLATE
More informationEDP# Model 26 MAINTENANCE INSTRUCTIONS AND PARTS LIST. Better By . :;]- ~, Iiii. McMINNVILLE, TENNESSEE D AC
EDP# 040 Model MAINTENANCE INSTRUCTIONS AND PARTS LIST Better By Design@). :;]- ~, Iiii McMINNVILLE, TENNESSEE 70 D AC 5-47-555 PARTS LIST: Stand & Table ITEM PART ITEM PART NO. NO. DESCRIPTION IOTY. NO.
More informationRYOBI 10 in. (254 mm) TABLE SAW MODEL NO. BT3100 REPAIR SHEET
RYOBI 0 in. (4 mm) TABLE SAW MODEL NO. BT00 REPAIR SHEET FOR MITER TABLE ASSEMBLY, REFER TO FIGURE B FOR BLADE GUARD ASSEMBLY, REFER TO FIGURE E FOR RIP FENCE ASSEMBLY, REFER TO FIGURE C FOR MOTOR ASSEMBLY,
More informationSECTION 9: PARTS Cabinet & Base
SECTION 9: PARTS 5 5-1 48 3 75 90 49 4 91 333 46 47 30 89 88 2 34 33 37 36 78 35 32 326 316 49 42 45 83 84V2 43 1 7 8 9 12 87 10 11 Cabinet & Base 31 17 20 40 39 136 41 135 85 86 8 28 26 18 19 21 19 370
More informationNote: Parts without part numbers are for reference only and cannot be purchased individually.
Parts Ordering Replacement Parts To order parts or reach our service department, call 1-800-274-6848 between 7:30am and 5:30pm (CST), Monday through Friday. Having the Model Number and Serial Number of
More informationD('00 D]^ ('&'. G8IKJ
1 2 5 6 7 8 11 12 10 13 14 15 27 28 16 26 29 30 25 17 19 20 22 21 32 23 24 31 42 43 33 34 40 41 35 49 36 37 51 52 53 44 45 46 47 38 39 48 18-40- 1 XM1099001 CONTROL PANEL FACE 29 XPCAP50M CAP SCREW M5-.8
More informationCoolant Tank Screen Leg Idle End Lockwasher 64 B-015B Leg Drive End Machine Screw 1/4-20 x 3/4 Round Head
Always give model number, serial number and part number when ordering repair parts. BED, COOLANT & DASH POT PARTS LIST (Cont'd.) REF NO. PART NUMBER DESCRIPTION 19 B-077 Vise Slide Block 20 B-045 Vise
More informationSECTION 9: PARTS. Electrical Box. (0000 Series Parts) 0000 Series Parts List
SECTION 9: PARTS Electrical Box (0000 Series Parts) 0000 Series Parts List 1 P04920001 CONTACTOR 6 P04920006 FUSE 2A (LC1-D0910, B5, 24V, 50HZ) 7 P04920007 FUSE HOUSING 2 P04920002 CONTACTOR 8 P04920008
More informationModel No: SM2503. Parts Information: Mini Lathe & Drilling Machine
Page 1 of 5 Page 2 of 5 1 SM2503.001 CHANGE GEAR COVER 2 SM2503.002 CAP SCREW M4x8 3 SM2503.003 CAP SCREW M4x12 4 SM2503.004 HINGE L*B=38*31 5 SM2503.005 WASHER 4 6 SN4.S STEEL NUT M4 ZINC DIN934 (SINGLE)
More informationRYOBI. 10 in. (254 mm) TABLE SAW MODEL NO. BTS15 REPAIR SHEET
RYOBI 0 in. ( mm) TABLE SAW MODEL NO. BTS REPAIR SHEET FIGURE A 0 0 0 0 The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding
More informationW /2" Dovetail Machine PARTS. Table PARTS -36-
Table -36- Table Parts List 101 X1805101 FENCE 117 X1805117 INDICATOR TEMPLATE 1" & 2" 102 X1805102 SLIDING ROD 118 X1805118 INDICATOR TEMPLATE 1-1/2" & 2-1/2" 103 XPSB31M CAP SCREW M8-1.25 X 25 119 XPSB04M
More informationHeadstock Gear System
Headstock Gear System (0000 Series Parts) 10 7 6 5 4 3, 2 16 11 12 13 14 15 9,8 1 90 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 91 93 94 95 96 97 98 99 100 102 104 106 108 109 92 101 103 105
More informationModel W1819/W1820 (Mfg. Since 09/11) PARTS. Body V V PARTS -79-
-79- Model W1819/W1820 (Mfg. Since 09/11) 155V2 155-1 155-2 155-3V2 155-6 155-5 108 109 109 156 110 110 168 169 170 171 101 102 103 104 105 106 107 108 109 114 115 118 119 120 121 122 123 124 125 126 127
More informationG0513X2 Main -87- G0513 Series Bandsaws 82V V2 82-6V2 95A V2 82-5V2 82-1V2 82-4V V A
G0513X2 Main 23 55 22 48 17 17-1 17-2 21 7 17-3 17-2 17-4 24 17-5 18-5 22 24 21 55A 50 8 9 49 11 12 13 14 15 47 16 10 46 45 3 44 43 39 38 37 39 40 32 33 36 42 34 35 2 25 28 18-4 18-2 18-3 31 30 29 18-1
More informationMODEL RA-200N RADIAL ARM SAW
ITEM NO PART NO DESCRIPTION PRICE 1 6130089 HEX. NUT (L.H.T.) W5/8"-18UNF 2.18 2 6900079 CONICAL SPRING 16.3 X 31.5 X 1.2 0.78 3 6940444 OUTER FLANGE 4.49 4 6940443 INNER FLANGE 4.91 5 6100509 PARALLEL
More informationOperating Instructions and Parts Manual. 10 x 16 Horizontal Band Saw Models J-7020, J-7040
Operating Instructions and Parts Manual 10 x 16 Horizontal Band Saw Models J-7020, J-7040 JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-414472 Ph.: 800-274-6848 Revision C2 03/2014 www.jettools.com
More informationIMPORTANT: Chuck guard MUST be installed before drill chuck!
IMPORTANT: Chuck guard MUST be installed before drill chuck! Model G7945/G7946 ***IMPORTANT UPDATE*** For Machines Mfg. Since December, 2012 and Owner's Manual Revised August, 2009 The following changes
More informationPARTS. Model W1701W (For Machines Mfd. Since 1/16) -47- REF PART # DESCRIPTION REF PART # DESCRIPTION
Base Breakdown 29 25 2 3 31 8 9 32 28 27 26 23 22 19 18 17 33 36 21 1 6 3 35 37 38 390 33 3 16 3-3-2 15 3-3 3-1 3-6 3-5 12 3-7 1 11 5 7 2 7 10 9 3 6 6 2 1 2 3 5-6- Base Parts List 1 X1701W001 STAND SIDE
More informationSECTION 9: PARTS. Table Breakdown REF PART # DESCRIPTION REF PART # DESCRIPTION
SECTION 9: PARTS Table Breakdown 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 23 25 17 26 27 8 1 P0675001 CAP SCREW M8-1.25 X 30 15 P0675015 SUPPORT BLOCK 2 P0675002 TABLE SUPPORT BLOCK
More informationOperating Instructions
Operating Instructions Holding the material against the angle gauge slide it into the forming head. Be sure that the material remains against the gauge until work is finished. NOTE: This machine will handle
More informationSECTION 9: PARTS G0513/G0513P/G0513ANV
SECTION 9: PARTS G0513/G0513P/G0513ANV Main 21 22 23 82-6 82-5 48 22 19 20 24 18 17 24 17 26 21 55 17 16 14 15 32 33 34 20 18 27 25 50 13 47 18 82-1 175 35 55A 49 9 11-1 10 46 45 11 12 44 176 39 38 37
More informationCATALOG OF REPLACEMENT PARTS
CATALOG OF REPLACEMENT PARTS FMS40 MIXER ML-134476 ML-134477 ML-141002 FORM 43182 Rev. A (April 2014) F-43182 Rev. A (April 2014) - 2-2014 Table of Contents 5 CONTROL PANEL 7 ELECTRICAL COMPONENTS 9 ATTACHMENT
More informationREAD THIS FIRST. For questions or help with this product contact Tech Support at (570) or
READ THIS FIRST Models G0453, G0453Z, G0454, G0454Z ***IMPORTANT UPDATE*** For Machines Mfd. Since 09/17 and Owner's Manuals Revised 11/12 For questions or help with this product contact Tech Support at
More informationM1110 Mill with Dovetail Column. Headstock PARTS -33-
-33- M1110 Mill with Dovetail Column 1012 1082 1083 1001 1084 1002 1003 1005 1006 1007 1008 1009 1010 1011 1097 1096 1095 1019 1017 1094 1073 1015 1081 1016 1013 1014 1018 1020 1021 1022 1023 1024 1025
More information20" WOODTURNING LATHE Model 3520A
20" WOODTURNING LATHE Model 3520A Instruction Manual & Parts List M-0460221 (800) 248-0144 www.powermatic.com SPECIFICATIONS: 3520A Lathe Table with standard extensions... 28 x 38 Distance Between Centers...
More informationOperating Instructions and Parts Manual 5-ft. Radial Arm Drill Press Models J-1600R, J-1600R-4
Operating Instructions and Parts Manual 5-ft. Radial Arm Drill Press Models J-1600R, J-1600R-4 JET 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-320038 Ph.: 800-274-6848 Revision H 01/2016
More informationHorizontal Band Saw. Operating Instructions and Parts Manual. Models EHB-1018VM EHB-1018VMH
Operating Instructions and Parts Manual Horizontal Band Saw Models EHB-08VM EHB-08VMH JET 427 New Sanford Road LaVergne, Tennessee 37086 www.jettools.com Ph.: 855-336-4032 Part No. M-89070 REV B2 08/204
More informationMODEL G0759 MILL/DRILL w/stand & DRO MANUAL INSERT
MODEL G0759 MILL/DRILL w/stand & DRO MANUAL INSERT The Model G0759 is the same machine as the Model G0704 except the Model G0759 has a 3-axis DRO. Besides the differences noted in this insert, all other
More informationCATALOG OF REPLACEMENT PARTS
CATALOG OF REPLACEMENT PARTS 3000 SERIES AUTOMATIC SLICERS 3713 ML-136144 3713 (Canada) ML-136177 3713N ML-136181 3713N (Canada) ML-136184 3913 ML-136145 3913 (Canada) ML-136179 3913N ML-136183 3913N (Canada)
More information