Additional Information

Size: px
Start display at page:

Download "Additional Information"

Transcription

1 NUMBER: S.M. REF.: Listed in Table ENGINE: EPA04/07 Series 60 DATE: January 2013 SUBJECT: CHECKING CYLINDER LINER PROTRUSION ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change Checking Cylinder Liner Added Link DDC-SVC-MAN-0004 EPA04 Series 60 Protrusion Additional Information Altered steps, Added link DDC-SVC-MAN-0005 EPA07 Series 60 Installation of Cylinder Liner Additional Information Added Link Altered steps, Added link Page numbers are based on the most recent version of the individual publication and may be adjusted throughout the annual print cycle.

2 THE FOLLOWING APPLIES TO DDC-SVC-MAN-0004

3 CHECKING CYLINDER LINER PROTRUSION Check as follows: 1. Wipe the inside and outside of the liner clean. Be sure the block bore and counter bore are clean, so the liner flange will seat properly. The block counter bore depth must be to mm ( to in) and must not vary more than 0.04 mm ( in) in depth around the circumference. Variation between two adjacent block counter bores may not range in depth more than mm (0.002 in) when measured in the center line of block. Specifications are listed in Table. 1. Cylinder Block A. Counterbore Depth Measurement Figure 1 Measuring Counterbore Depth Thoroughly clean the cylinder block liner counter bores to remove any foreign material. Foreign material in the cylinder liner counter bores can cause the liner to seat improperly. 2. Install the cylinder liner into the engine block without any seals. It is necessary to leave the cylinder liner installation tool in place until after the liner protrusion is measured.

4 3. Install J A, over the liner. See Figure 2. Figure 2 Cylinder Liner Installation Tools 4. Thread three cylinder head bolts through the tool and into a head bolt hole so that the round shoe of the tool is centered over the liner. It is not necessary to torque the bolts. 5. Tighten the bolts. 6. Turn the threaded center bolt in a clockwise direction. As the round shoe of the tool reaches the liner, ensure that the shoe is properly positioned into the cylinder liner. 7. Continue turning the bolt until the liner bottoms in the cylinder counterbore. Apply a tightening torque of 60 N m (44 lb ft) to the installation tool center bolt. 8. Install a dial indicator sled gage. See Figure 2.

5 9. Measure the distance from the top of the liner flange to the top of the block. See Figure 3. Figure 3 Cylinder Liner Protrusion [a] [b] Allowable liner protrusion is to mm ( to in) with no more than mm (0.002 in) variation between any two adjacent cylinders. Specifications are listed in Table. If the liner protrusion exceeds the maximum allowable, remove the liner and check for debris under the liner flange. If there is no debris, machine the liner counterbore. Refer to section Additional Information.

6 ADDITIONAL INFORMATION SHOP NOTES Shop notes contains information on checking bearing clearances, the crankshaft remanufacturing procedures and a glossary. CYLINDER BLOCK LINER BORING Further information will be printed as it is developed. MACHINING CYLINDER BLOCK COUNTERBORES Cutter plate assembly (J 41063) is used with Porta-Matic boring tool (PT 2050 D) to machine cylinder block counterbores for the installation of repair bushings. J features a special diameter and taper design which will permit the machining of the counterbore area in accordance with Detroit specifications. Use the appropriate Detroit part when installing the counterbore insert (repair bushing). Counterbore insert part number can be located in AP Rev. Machine the cylinder block counterbores as follows: 1. Ensure block deck surface and boring tool base plate are clean and burr free. 2. Plug push tube opening, oil galleys and lower liner packing areas to seal out any contaminating particles. Ensure cutter is marked Series 60. Maintain a sharp cutter bit to ensure the cylinder block counterbore is accurately machined.

7 3. Using cutter (PT ) set to the dimensions listed in Table 2 and see Figure 13. Table 1 Area to be Machined Cutter Setting Dimensions Depth of Cut Upper counterbore ± mm (6.370 ±.0005 in. Diameter) PT Cutter Dimensions mm (.602 in.) Figure 4 Bushing Repair Area 4. Assemble Cutter Plate (PT 2090) to the Porta-Matic mainshaft. See Figure 14. Figure 5 Cutter Plate(PT 2090) Location 5. Mount Porta-Matic over cylinder to be bored. Open feed valve to lower cutter plate into cylinder bore. Push down firmly while rotating the mainshaft to insure proper alignment of Porta-Matic. 6. With cutter plate centered in the cylinder bore, align base plate with the four cylinder head bolt holes in block deck while maintaining as much base plate to block deck contact as possible. 7. Cross-torque all four cylinder head bolts slowly to 67 N m (50 lb ft). Rotate mainshaft to insure that the cutter plate is centered and moves freely. If binding occurs loosen the four cylinder head bolts and repeat steps 8 and Pull up on the mainshaft to retract the cutter plate to the highest position and close the feed valvetolockinposition.

8 NOTICE: Ensure cutter bit is completely inserted into cutter slot. 9. Insert cutter into slot of cutter plate. Hold cutter bit against the main shaft of the boring tool and tighten the cutter plate set screw to secure the cutter. 10. Slowly lower the cutter and allow to rest onto engine block deck surface. Insert a mm (0.004 in.) shim between cutter and engine block. Set the depth of cut using bushing (PT 8065). Tighten socket set screw to hold depth collar in place. See Figure 15. Figure 6 Upper Counterbore Cutting Area. 11. Retract cutter plate to the up position and lock machine. 12. Attach a right angle drill (PT 7145 A) and proceed to bore hole until Porta Matic freewheels. 13. Open feed valve and retract cutter plate upward. Remove cutter bit. 14. Repeat steps 5 to 13 for each of the next five bores. 15. Cut the counterbore ledge depth to ± mm (0.353 ± in.) using counterbore tool (PT 2250 B) and the appropriate cutter plates. Follow normal ledge cutting procedures to achieve the finished counterbore depth. MACHINING CYLINDER BLOCK COUNTERBORES USING SHIMS Cutter plate assembly (J 41065) is used with Counterbore tool (PT 2250 B) to machine cylinder block counterbores for the installation of repair shims. See Figure 7. Use the appropriate Detroit part when installing the counterbore shims.

9 Counterbore shim part numbers can be located in 11TS-8Rev. 1. Cylinder Block 2. Cylinder Liner Protrusion 3. Cylinder Liner Figure 7 Cylinder Liner Protrusion 1. Remove cylinder head. Refer to section. 2. Remove oil pan. Refer to section. 3. Remove cylinder liner. Refer to section. 4. Ensure block deck surface and boring tool base plate are clean and free of burrs. 5. Plug all open areas of the engine compartment to seal out any contaminating particles. Ensure cutter is marked Series 60. Maintainasharpcutterbit to ensure the cylinder block counterbore is accurately machined. 6. Retract the cutting bit into the cutting plate. 7. Mount the counterbore cutting tool over the cylinder to be machined. Install mounting bolts into the appropriate cylinder head bolt holes, leaving the bolts loose.

10 8. Lower the cutting plate (2) to rest in the cylinder bore (1) and rotate the T-handle to center the tool. See Figure 8. Figure 8 Cutter Plate (PT 2090) Location 9. Torque the two opposing mounting bolts to 68 N m (50 lb ft). Verify that the tool is still centered in the bore. If not, then loosen bolts and re-center the tool. If centered, torque the two remaining mounting bolts to 68 N m (50 lb ft). 10. Raise the tapered cutting head from the block and insert the spacer block. While there is no load on the tool, extend the cutter bit outward (using a clockwise rotation of the cutting bit screw) until it just touches a 0.15 mm (0.005 in.) feeler gauge or shim placed next to the vertical wall of the counterbore. Tighten the Allen head hold-down screws. Figure 9 Spacer Block PT Remove the spacer block and slowly lower the cutting head into the counterbore. (Be careful not to damage the cutting bit).

11 12. Adjust the lower locking collar downward until it comes in contact with bronze bushing, and the cutter bit is not resting on lower surface of counterbore. Rotate the T-handle to ensure there is no binding or scraping of the counterbore walls. If so, adjust cutting bit. 13. Slowly back off the lower locking collar until the cutting bit is just touching the lower surface of the counterbore. 14. Set the depth of the cut by using the repair shim. Insert the shim between the locking collars, lower the upper lock collar down until it comes in contact with the shim. Tighten the thumb screwonthetopcollar. If cutting more than one counterbore, the shim used to set the depth of the cut in each cylinder must be used in that cylinder. Failing to do so may increase/decrease the liner protrusion. 15. Lubricate the tool bushings. Back-off the lower collar by two graduations, mm ( in.). Rotate the T-handle clockwise with moderate, constant pressure, stopping at random positions to prevent creating a ridge in the counterbore. Continue backing-off the lower collar, two graduations at a time, until the collars come together. 16. Raise the cutting tool from the counterbore and insert depth spacer. 17. Retract the cutting bit into the cutting plate to protect the bit. 18. Remove the cutting tool from engine. 19. Remove all protective material used to seal out any contaminating particles and clean any/all areas that were not protected. 20. Place the shim on the lower ledge of the counterbore. 21. Insert the cylinder liner and measure liner protrusion. Refer to section. 22. Install the cylinder liner. Refer to section. 23. Install the cylinder head. Refer to section. 24. Install the oil pan. Refer to section.

12 THE FOLLOWING APPLIES TO DDC-SVC-MAN-0005

13 INSTALLATION OF CYLINDER LINER Install as follows: Refer to section for 14L liner, piston and connecting rod procedure. 1. Wipe the inside and outside of the liner clean. Be sure the block bore and counter bore are clean, so the liner flange will seat properly. The block counter bore depth must be to mm ( to in.) and must not vary more than 0.04 mm ( in.) in depth around the circumference. No two adjacent block counter bores may range in depth more than mm (0.001 in.) when gaged along the longitudinal cylinder block centerline. Specifications are listed in Table, and listed in Table. Thoroughly clean the cylinder block liner counter bores to remove any foreign material. Foreign material in the cylinder liner counter bores can cause the liner to seat improperly. 2. Lubricate the seal rings and crevice seal with clean petroleum jelly. 3. Install two new seal rings and a new crevice seal into their respective grooves in the liner. 4. Install the cylinder liner, piston and rod assembly into the cylinder bore. Refer to section 5. Install J A, over the liner. See Figure 10. It is necessary to leave the cylinder liner installation tool in place until after the liner protrusion is measured. Figure 10 Cylinder Liner Installation Tools 6. Thread three cylinder head bolts through the tool and into a head bolt hole, so that the round shoe of the tool is centered over the liner. 7. Tighten the bolts.

14 It is not necessary to torque the bolts. 8. Turn the threaded center bolt in a clockwise direction. As the round shoe of the tool reaches the liner, ensure that the shoe is properly positioned into the cylinder liner. 9. Continue turning the bolt until the liner bottoms in the cylinder counterbore. Apply a tightening torque of 60 N m (44 lb ft) to the installation tool center bolt. 10. Install a dial indicator sled gage. See Figure.

15 11. Measure the distance from the top of the liner flange to the top of the block. See Figure 11 [a] Allowable liner protrusion is to mm ( to in.) with no more than mm (0.002 in.) variation between any two adjacent cylinders. Specifications are listed in Table. [b] If the liner protrusion exceeds the maximum allowable, remove the liner and check for debris under the liner flange. [c] c. If the liner protrusion does the meet the minimum allowable, remove the liner and machine the counterbore. Refer to Additional Information. Figure 11 Cylinder Liner Protrusion

16 ADDITIONAL INFORMATION SHOP NOTES Shop notes contains information on checking bearing clearances, the crankshaft remanufacturing procedures and a glossary. CYLINDER BLOCK LINER BORING Further information will be printed as it is developed. MACHINING CYLINDER BLOCK COUNTERBORES Cutter plate assembly (J 41063) is used with Porta-Matic boring tool (PT 2050 D) to machine cylinder block counterbores for the installation of repair bushings. J features a special diameter and taper design which will permit the machining of the counterbore area in accordance with Detroit specifications. Use the appropriate Detroit part when installing the counterbore insert (repair bushing). Counterbore insert part number can be located in AP Rev. Machine the cylinder block counterbores as follows: 1. Ensure block deck surface and boring tool base plate are clean and burr-free. 2. Plug all open areas of the engine compartment to seal out any contaminating particles. Ensure cutter is marked Series 60. Maintain a sharp cutter bit to ensure the cylinder block counterbore is accurately machined. 3. Verify that the Micrometer block is within specifications. Insert the setting standard with the side stamped UP between the cutter stop and the spindle. Hold the setting standard firmly; turn the micrometer thimble until the micrometer spindle is in contact with the setting standard. Does the micrometer read inches? [a] Yes,gotostep5. [b] No, the micrometer will need to be calibrated. Go to step 4.

17 4. To calibrate the Micrometer, loosen the set screw and move the micrometer to read inches. Slide the spindle to fit snug against the setting standard; tighten the set screw. Back off the micrometer and recheck the reading. If it does not read inches, readjust again and recheck. See Figure Cutter Stop 4. Thimble 2. Spindle 5. Setting Standard 3. Set Screw 6. Micrometer Figure 12 Micrometer 5. Using cutter (PT ) set to the dimensions listed in Table 2 and see Figure 13. Area to be Machined Cutter Setting Dimensions Depth of Cut Upper counterbore ± mm (6.370 ±.0005 in. Diameter) mm (.602 in.) Table 2 PT Cutter Dimensions Figure 13 Bushing Repair Area

18 6. Assemble Cutter Plate (PT 2090) to the Porta-Matic mainshaft. See Figure 14. Figure 14 Cutter Plate (PT 2090) Location 7. Mount Porta-Matic over cylinder to be bored. Open feed valve to lower cutter plate into cylinder bore. Push down firmly while rotating the mainshaft to insure proper alignment of Porta-Matic. 8. With cutter plate centered in the cylinder bore, align base plate with the four cylinder head bolt holes in block deck while maintaining as much base plate to block deck contact as possible. 9. Cross-torque all four cylinder head bolts slowly to 67 N m (50 lb ft). Rotate mainshaft to insure that the cutter plate is centered and moves freely. If binding occurs, loosen the four cylinder head bolts and repeat steps 7 through Pull up on the mainshaft to retract the cutter plate to the highest position and close the feed valve to lock in position. NOTICE: Ensure cutter bit is completely inserted into cutter slot. 11. Insert cutter into slot of cutter plate. Hold cutter bit against the main shaft of the boring tool and tighten the cutter plate set screwtosecurethecutter.

19 12. Slowly lower the cutter and allow to rest onto engine block deck surface. Insert a mm (0.004 in.) shim between cutter and engine block. Set the depth of cut using bushing (PT 8065). Tighten socket set screw to hold depth collar in place. See Figure 15. Figure 15 Upper Counterbore Cutting Area. 13. Retract cutter plate to the UP position and lock machine. 14. Attach a right angle drill (PT 7145 A) and proceed to bore hole until Porta Matic freewheels. 15. Open feed valve and retract cutter plate upward. Remove cutter bit. 16. Repeat steps 7 to 15 for each of the next five bores. 17. Cut the counterbore ledge depth to ± mm (0.353 ± in.) using counterbore tool (PT 2250 B) and the appropriate cutter plates. Follow normal ledge cutting procedures to achieve the finished counterbore depth. MACHINING CYLINDER BLOCK COUNTERBORES USING SHIMS Cutter plate assembly (J 41065) is used with Counterbore tool (PT 2250 B) to machine cylinder block counterbores for the installation of repair shims. See Figure 16. Use the appropriate Detroit part when installing the counterbore shims.

20 Counterbore shim part numbers can be located in 11TS-8Rev. 1. Cylinder Block 2. Cylinder Protrusion 3. Cylinder Liner Figure 16 Cylinder Liner Protrusion 1. Remove cylinder head. Refer to section. 2. Remove oil pan. Refer to section. 3. Remove cylinder liner. Refer to section. 4. Ensure block deck surface and boring tool base plate are clean and free of burrs. 5. Plug all open areas of the engine compartment to seal out any contaminating particles. Ensure cutter is marked Series 60. Maintain a sharp cutter bit to ensure the cylinder block counterbore is accurately machined. 6. Retract the cutting bit into the cutting plate. 7. Mount the counterbore cutting tool over the cylinder to be machined. Install mounting bolts into the appropriate cylinder head bolt holes, leaving the bolts loose.

21 8. Lower the cutting plate (2) to rest in the cylinder bore (1) and rotate the T-handle to center the tool. See Figure 17. Figure 17 Cutter Plate (PT 2090) Location 9. Torque the two opposing mounting bolts to 68 N m (50 lb ft). Verify that the tool is still centered in the bore. If not, then loosen bolts and re-center the tool. If centered, torque the two remaining mounting bolts to 68 N m (50 lb ft). 10. Raise the tapered cutting head from the block and insert the spacer block. While there is no load on the tool, extend the cutter bit outward (using a clockwise rotation of the cutting bit screw) until it just touches a 0.15 mm (0.005 in.) feeler gauge or shim placed next to the vertical wall of the counterbore. Tighten the Allen head hold-down screws. Figure 18 Spacer Block PT Remove the spacer block and slowly lower the cutting head into the counterbore. (Be careful not to damage the cutting bit).

22 12. Adjust the lower locking collar downward until it comes in contact with bronze bushing, and the cutter bit is not resting on lower surface of counterbore. Rotate the T-handle to ensure there is no binding or scraping of the counterbore walls. If so, adjust cutting bit. 13. Slowly back off the lower locking collar until the cutting bit is just touching the lower surface of the counterbore. 14. Set the depth of the cut by using the repair shim. Insert the shim between the locking collars, lower the upper lock collar down until it comes in contact with the shim. Tighten the thumb screw on the top collar. If cutting more than one counterbore, the shim used to set the depth of the cut in each cylinder must be used in that cylinder. Failing to do so may increase/decrease the liner protrusion. 15. Lubricate the tool bushings. Back-off the lower collar by two graduations, mm ( in.). Rotate the T-handle clockwise with moderate, constant pressure, stopping at random positions to prevent creating a ridge in the counterbore. Continue backing-off the lower collar, two graduations at a time, until the collars come together. 16. Raise the cutting tool from the counterbore and insert depth spacer. 17. Retract the cutting bit into the cutting plate to protect the bit. 18. Remove the cutting tool from engine. 19. Remove all protective material used to seal out any contaminating particles and clean any/all areas that were not protected. 20. Place the shim on the lower ledge of the counterbore. 21. Insert the cylinder liner and measure liner protrusion. Refer to section. 22. Install the cylinder liner. Refer to section. 23. Install the cylinder head. Refer to section. 24. Install the oil pan. Refer to section.

23 ADDITIONAL SERVICE INFORMATION Additional service information is available in Power Service Literature. TM Detroit, DDC, Series 60 and the spinning arrows design are registered trademarks of Detroit Diesel Corporation. Copyright 2013 Detroit Diesel Corporation. All rights reserved. Printed in U.S.A.

NUMBER: S.M. REF.: Listed in Table ENGINE: Series 50/50G DATE: October 2013 SUBJECT: MACHINING CYLINDER BLOCK COUNTERBORES

NUMBER: S.M. REF.: Listed in Table ENGINE: Series 50/50G DATE: October 2013 SUBJECT: MACHINING CYLINDER BLOCK COUNTERBORES NUMBER: 10 25 13 S.M. REF.: Listed in Table ENGINE: Series 50/50G DATE: October 2013 SUBJECT: MACHINING CYLINDER BLOCK COUNTERBORES ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section

More information

NUMBER: S.M. REF.: Listed in Table ENGINE: Series 60 DATE: February 2010

NUMBER: S.M. REF.: Listed in Table ENGINE: Series 60 DATE: February 2010 NUMBER: 2 1 10 S.M. REF.: Listed in Table ENGINE: Series 60 DATE: February 2010 SUBJECT: CYLINDER LINER PROTRUSION & INSTALLATION ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title

More information

KL50000 Counter Bore OPERATING INSTRUCTIONS. U.S. Patent No CA Patent No

KL50000 Counter Bore OPERATING INSTRUCTIONS. U.S. Patent No CA Patent No KL50000 Counter Bore Re-Condtioning Tool Kit OPERATING INSTRUCTIONS U.S. Patent No. 8.308.401 CA Patent No. 2667147 315 Garden Avenue Holland, MI 49424 klineindustries.com 1-800-824-KLINE (5546) cservice@klineind.com

More information

w w w. h d o n l i n e s h o p. d e TIMKEN BEARING CONVERSION TOOL GENERAL INSTALLATION -J04672 REV Kit Number Models

w w w. h d o n l i n e s h o p. d e TIMKEN BEARING CONVERSION TOOL GENERAL INSTALLATION -J04672 REV Kit Number Models -J067 REV. 008-07- GENERAL Kit Number 8-08 Models TIMKEN BEARING CONVERSION TOOL For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com

More information

4-8 HSF 250 Patriot. Line Stop Fitting Installation Instructions. Installation Instructions and Best Practices continued on back

4-8 HSF 250 Patriot. Line Stop Fitting Installation Instructions. Installation Instructions and Best Practices continued on back HSF 250 Patriot Heavy Duty Line Stop Fitting - 4, 6, 8 inch Nominal Sizes Line Stop Fitting Installation Instructions Push and Pin Completion Plug Installation Instructions IMPORTANT: Read installation

More information

MUELLER. Improved, Centurion Series, Modern Improved, and 107. Fire Hydrants. Inserting Extension Sections. Reliable Connections

MUELLER. Improved, Centurion Series, Modern Improved, and 107. Fire Hydrants. Inserting Extension Sections. Reliable Connections insertion Instructions manual MUELLER Improved, Centurion Series, Modern Improved, and 107 table of contents PAGE Centurion Series Fire Hydrant Adding an Extension 2-3 Improved Fire Hydrant Inserting Extension

More information

SUPER PRO GUN & SUPER PRO GUN II

SUPER PRO GUN & SUPER PRO GUN II MAGNUM VENUS PRODUCTS Maintenance & Repair Manual Part No. M6707-1-1 Revision 04.14.01 Maintenance & Repair Corporate HQ & Mfg. Phone: (727) 573-2955 Fax: (727) 571-3636 Email: info@magind.com Web: www.magind.com

More information

MUELLER. Improved, Centurion Series, Modern Improved, and 107. Fire Hydrants. Inserting Extention Sections. Reliable Connections

MUELLER. Improved, Centurion Series, Modern Improved, and 107. Fire Hydrants. Inserting Extention Sections. Reliable Connections insertion Instructions manual MUELLER Improved, Centurion Series, Modern Improved, and 107 table of contents PAGE Centurion Series Fire Hydrant Adding an Extention 2-3 Improved Fire Hydrant Inserting Extention

More information

Removing Right-Side. Components. Right-Side. Components. Click Here to Go Back AT THIS POINT

Removing Right-Side. Components. Right-Side. Components. Click Here to Go Back AT THIS POINT Click Here to Go Back NOTE: There is an oil passage beneath the driven gear/drive gear assembly. This passage should be plugged prior to removing the driven gear and drive gear. Failure to do so could

More information

MSR/MSB Mechanical Setting Tool

MSR/MSB Mechanical Setting Tool Tech Unit No: 0620000004 Revision: B Approved By: Quality Engineer Date: 2014-12-16 MSR/MSB Mechanical Setting Tool FEATURES: Special designed Bow Spring provides positive control and allows one size Mechanical

More information

DRIVE COMPONENTS REMOVAL. 9. FXCW/C: see Figure Remove bolt (9), sprocket retainer (8), and thrust washer (7). NOTE PRIMARY DRIVE LOCKING TOOL

DRIVE COMPONENTS REMOVAL. 9. FXCW/C: see Figure Remove bolt (9), sprocket retainer (8), and thrust washer (7). NOTE PRIMARY DRIVE LOCKING TOOL DRIVE COMPONENTS REMOVAL PART NUMBER HD-7977 TOOL NAME PRIMARY DRIVE LOCKING TOOL S To remove the primary chain, remove compensating sprocket, clutch assembly and primary chain as an assembly:. Remove

More information

BHJ Products, Inc. Parts List & Instructions

BHJ Products, Inc. Parts List & Instructions Product Name: O-Ring Groove Cutter Page 1 of 6 Kit Contents: 1x Cutter Head Assembly with Handle & Adjustable Tool Block 1x Graduated Adjusting Screw 1x Adjustable Tool Holder 1x Carbide Insert (Size of

More information

Chain Drive Vise. Installation Instructions. (revised 05/04/2016)

Chain Drive Vise. Installation Instructions. (revised 05/04/2016) Chain Drive Vise Installation Instructions (revised 05/04/2016) Lie-Nielsen Chain Drive Vise Instructions Table of Contents page About Your Chain Drive Vise 3 Parts List 4 Exploded Parts Diagram 5 step

More information

MSR/MSB Mechanical Setting Tool

MSR/MSB Mechanical Setting Tool Tech Unit No: 0620000004 Revision: C Approved By: Quality Engineer Date: 201-1-9 MSR/MSB Mechanical Setting Tool FEATURES: Special designed Bow Spring provides positive control and allows one size Mechanical

More information

BHJ Products, Inc. Parts List & Instructions

BHJ Products, Inc. Parts List & Instructions Product Name: O-Ring Groove Cutter Adjustable Tool Block Upgrade Page 1 of 5 Prototype Kit Contents: 1x Adjustable Tool Block 1x Adjustable Tool Holder 1x Graduated Adjusting Screw 1x 1/8 Registration

More information

SERVICE PARTS LIST. M18 FUEL SAWZALL Reciprocating Saw F56A BULLETIN NO CATALOG NO

SERVICE PARTS LIST. M18 FUEL SAWZALL Reciprocating Saw F56A BULLETIN NO CATALOG NO 47(5x) 46 45 00 44 0 59 43 42 84 51 57 46 47 48 59 83 64 77 48 47(2x) 49(2x) 40 58 See service note on page 5 41 82 51 40 41 42 43 44 45 87 52 27 28 34 57 29 (6x) 60 28 EXAMPLE: Component Parts (Small

More information

TorqueMaster Replacement Spring

TorqueMaster Replacement Spring TorqueMaster Replacement Spring Installation Instructions NOTE: Use these installation instructions in conjunction with the TorqueMaster Repair / Replacement Spring Program literature. Copyright 999 Wayne-Dalton

More information

25000 Series Lo-T TM Butterfly Control Valve Instructions

25000 Series Lo-T TM Butterfly Control Valve Instructions November 2001 25000 Series Lo-T TM Butterfly Control Valve Instructions Instruction No. 25.1:IM PRELIMINARY STEPS Before installation, note the flow direction arrow on the valve body. The flow should enter

More information

Series 760 Heavy Duty Fixed Displacement Motor. Parts and Repair Manual

Series 760 Heavy Duty Fixed Displacement Motor. Parts and Repair Manual Series 760 Heavy Duty Fixed Displacement Motor Parts and Repair Manual Series 760 Fixed Displacement Motor Contents Introduction 3 ID Tag Information 3 Parts List 4 Parts Drawing 5 Disassembly Instructions

More information

PET*STAR 4 OPERATOR MANUAL

PET*STAR 4 OPERATOR MANUAL Operator Manual 17315060 Rev. 0 (PS - 4) PET*STAR 4 OPERATOR MANUAL Paragraph Page 1.0 INTRODUCTION... 2 2.0 INSTALLATION... 2 3.0 ALIGNMENT... 2 4.0 SPHERICAL ROLLER BEARING & PILLOW BLOCK... 5 5.0 OUTBOARD

More information

ITEM NO. PART NO DESCRIPTION QTY.

ITEM NO. PART NO DESCRIPTION QTY. PUMP MAINTENANCE ITEM NO. PART NO DESCRIPTION QTY. 1 52002 Center Case 1 2 52052 Back End Plate 1 3 52051 Front End Plate 1 4 55090 Octagonal Nut 1 5 53001 Idler Gear 1 6 53002 Drive Gear 1 7 28062 Bushing

More information

Repair Manual MK40A-MK45A-MK50A MK55A-MK60A-MK65A. Ref Rev.C General Pump is a Member of The Interpump Group

Repair Manual MK40A-MK45A-MK50A MK55A-MK60A-MK65A. Ref Rev.C General Pump is a Member of The Interpump Group MK Repair Manual MK40A-MK45A-MK50A MK55A-MK60A-MK65A General Pump is a Member of The Interpump Group 8 INDEX 1. INTRODUCTION..................................................Page 3 2. REPAIR INSTRUCTIONS...........................................Page

More information

Quill Stop V2 Installation Guide 11/16/2014

Quill Stop V2 Installation Guide 11/16/2014 Thank you for purchasing the Quill Stop for the Sieg X3 (Grizzly G0463) and SX3 (Grizzly G0619) mills. Your feedback is always appreciated. Please email questions and comments to gregpriest@cox.net. What

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS TM X-10 Type 1F HIGH SECURITY ELECTRONIC LOCK Table of Contents Introduction... 1 Basic Tools and Materials Needed... 1 Lock Parts for Installation... 1 Installation Kit Contents...

More information

Repair Manual MWS45A-MWS50A-MWS55A MW32A-MWS36A-MWS40A. Ref Rev.D General Pump is a member of the Interpump Group

Repair Manual MWS45A-MWS50A-MWS55A MW32A-MWS36A-MWS40A. Ref Rev.D General Pump is a member of the Interpump Group MW/S 8 Repair Manual MWS45A-MWS50A-MWS55A MW32A-MWS36A-MWS40A General Pump is a member of the Interpump Group INDEX 1. INTRODUCTION..................................................Page 3 2. REPAIR INSTRUCTIONS...........................................Page

More information

Chain Drive Vise. Installation Instructions. (revised 11/29/2018)

Chain Drive Vise. Installation Instructions. (revised 11/29/2018) Chain Drive Vise Installation Instructions (revised 11/29/2018) Lie-Nielsen Chain Drive Vise Instructions Table of Contents page About Your Chain Drive Vise 3 Parts List 4 Exploded Parts Diagram 5 step

More information

Click Here to Go Back

Click Here to Go Back Click Here to Go Back Fig. -94 Fig. -97 CC42D 10. Remove the cap screw securing the gear shift stopper plate pin retainer; then remove the retainer. Fig. -95 CC45D 12. Remove the link arm and account for

More information

Typical Group D Rear Acoustical Cover Installation

Typical Group D Rear Acoustical Cover Installation SERIES 60 SERVICE MANUAL 1. Gear Case Cover 5. Bolt 2. Gear Case 6. Acoustical Cover 3. Acoustical Cover Snap 7. Acoustical Cover 4. Acoustical Cover Clip 8. Nut Figure 1-179 Typical Group D Rear Acoustical

More information

Setup & Operating INSTRUCTIONS. for (FOR PIN FITTING AND ROD RECONDITIONING)

Setup & Operating INSTRUCTIONS. for (FOR PIN FITTING AND ROD RECONDITIONING) I-AG-400A Setup & Operating INSTRUCTIONS for SUNNEN AG-400 PRECISION GAGE (FOR PIN FITTING AND ROD RECONDITIONING) AG-400 Precision Bore Gage Range:.375 to 2.687 in. (9,5-68mm) Graduation of Dial:.0001

More information

LK36-LK40-LK45 LK50-LK55-LK60

LK36-LK40-LK45 LK50-LK55-LK60 LK Repair Manual LK36-LK40-LK45 LK50-LK55-LK60 INDEX 1. INTRODUCTION..................................................Page 3 2. REPAIR INSTRUCTIONS...........................................Page 3 2.1

More information

PORTABLE PULL TESTER

PORTABLE PULL TESTER 2425 West Vineyard Avenue, Escondido, California 92029-222 Phone: (800) 284-4460 Fax: (760) 746-4295 PORTABLE CABLE TERMINAL PULL TESTER AT520CT (Revised July 2003) AT520CT Portable Cable Terminal Pull

More information

MORTISE LOCK INSTALLATION INSTRUCTIONS

MORTISE LOCK INSTALLATION INSTRUCTIONS MORTISE LOCK INSTALLATION INSTRUCTIONS INSPIRE TM ROSELESS DESIGNER TRIM FM 340 Rev. 10/18 TABLE OF CONTENTS: DOOR PREPARATION 1 ML2000 LOCK HANDING 2 FULL WORKING TRIM (STD) 3 HALF WORKING TRIM (M30)

More information

RTI TECHNOLOGIES, INC.

RTI TECHNOLOGIES, INC. RTI TECHNOLOGIES, INC. BRC500 & BRC550 Arbor/Spindle Mechanism Adjustment & Service Technical Instructions The arbor/spindle mechanism of the BRC500/550 is designed to be robust for long life. Occasionally

More information

Fisher 667 Diaphragm Actuators Size 80 and 100

Fisher 667 Diaphragm Actuators Size 80 and 100 Instruction Manual 667 Size 80 and 100 Actuators Fisher 667 Diaphragm Actuators Size 80 and 100 Contents Introduction... 1 Scope of Manual... 1 Description... 2 Specifications... 2 Maximum Pressure Limitations...

More information

1. Turn off or disconnect power to unit (machine). 2. Push IN the release bar on the quick change base plate. Locking latch will pivot downward.

1. Turn off or disconnect power to unit (machine). 2. Push IN the release bar on the quick change base plate. Locking latch will pivot downward. Figure 1 Miniature Quick Change Applicators, of the end feed type, are designed to crimp end feed strip terminals to prestripped wires. Each applicator is set up to accept the strip form of certain specific

More information

Travel Trailer Latch With Dead Bolt Trailer Latch With Dead Bolt. U.S. Patent No. 5,927,773

Travel Trailer Latch With Dead Bolt Trailer Latch With Dead Bolt. U.S. Patent No. 5,927,773 60-250 Travel Trailer Latch With Dead Bolt 60-251 Trailer Latch With Dead Bolt Service Manual (Installation and Troubleshooting) U.S. Patent No. 5,927,773 CONTENTS 1. BASIC COMPONENTS 2. INSTALLATION OF

More information

MKS. MKS Series MKS 40 MKS 45 MKS 50 MKS 55 MKS 60 MKS 65. Repair Manual

MKS. MKS Series MKS 40 MKS 45 MKS 50 MKS 55 MKS 60 MKS 65. Repair Manual MKS Series MKS 40 MKS 45 MKS 50 MKS 55 MKS 60 MKS 65 Repair Manual INDEX. INTRODUCTION 3 2. REPAIR INSTRUCTIONS 3 2. Crank Mechanism Repair...3 2.. Crank Mechanism Disassembly...4 2..2 Crank Mechanism

More information

Fig. 2 DORMA-Glas Stand/Issue 02/03 Seite/Page 1/7

Fig. 2 DORMA-Glas Stand/Issue 02/03 Seite/Page 1/7 FSW Installation instructions Track rail 75 x 72 mm 1. Ceiling substructure and installation of the track rail (Fig. 1): The track rail must be bolted over its entire length (including the stacking track

More information

VSG4720. balancing. block machining. boring. cleaning. crankshaft. cylinder head machining. flywheel grinders. honing. motorcycle small engine

VSG4720. balancing. block machining. boring. cleaning. crankshaft. cylinder head machining. flywheel grinders. honing. motorcycle small engine TM engine rebuilding equipment balancing block boring cleaning crankshaft cylinder head flywheel grinders honing motorcycle small engine surfacing center center versatility New capabilities Tooling adapters

More information

Caution: Installation and Operation Instructions. Locking Mechanism (if supplied) Set Screws Backed Out. Mounting Orientation

Caution: Installation and Operation Instructions. Locking Mechanism (if supplied) Set Screws Backed Out. Mounting Orientation Genie Probe Regulator (GPR)/ Genie Probe (GP2)/ Genie Probe for Composite Sampler (CSA)/ And (Model H) Installation and Operation Instructions Caution: Not designed for external fire. Prior to use in a

More information

Page 1. SureMotion Quick-Start Guide: LACPACC_QS 1st Edition - Revision A 03/15/16

Page 1. SureMotion Quick-Start Guide: LACPACC_QS 1st Edition - Revision A 03/15/16 R K C T I Repair Kit Product Compatibility Repair Kit # Linear Actuator Assembly # LACPACC-002 LACPACC-003 LACP-16TxxLP5 (0.5-in lead screw pitch) LACP-16TxxL1 (1-in lead screw pitch) C P I R K 4 ea Flanged

More information

White Industries Front Hub Instructions

White Industries Front Hub Instructions White Industries Front Hub Instructions Tools required: 2mm hex/allen wrench, set of sockets, mallet, bearing puller, bearing press. Disassembly 1. Loosen the set screws, there are three or one depending

More information

General Four-Way Operation, Maintenance & Service Manual

General Four-Way Operation, Maintenance & Service Manual General Four-Way Operation, Maintenance & Service Manual SCOPE Included in the following pages you will find assembly drawings, exploded views, parts lists, assembly tips, operational descriptions and

More information

Model: SCD430 SCD640. Installation & Operation Guide P/N SCD640-95

Model: SCD430 SCD640. Installation & Operation Guide P/N SCD640-95 Model: SCD430 SCD640 Installation & Operation Guide P/N SCD640-95 Model SCD430 and SCD640 Kurt has two Self-Centering vises, a four-inch jaw width (SCD430) and a six-inch jaw width (SCD640). Jaw opening

More information

Di-Acro 36 Power Shear

Di-Acro 36 Power Shear OPERATOR S MANUAL & INSTRUCTIONS Di-Acro 36 Power Shear Di-Acro, Incorporated PO Box 9700 Canton, Ohio 44711 3713 Progress Street N.E. Canton, Ohio 44705 330-455-1942 330-455-0220 (fax) Revised 01/02 Sale

More information

SERVICE INSTRUCTIONS Model 9670 Lubricant Pump

SERVICE INSTRUCTIONS Model 9670 Lubricant Pump TM TM SERVICE INSTRUCTIONS Model 9670 Lubricant Pump 9670 DESCRIPTION Model 9670 Lubricant Pump is designed to pump light to heavy oils directly from the original container. This design features a 10:1

More information

INSTRUCTIONS

INSTRUCTIONS IMPORTANT: THIS IS A HIGH PERFORMANCE PART AND IMPROPER INSTALLATION COULD RESULT IN INJURY OR DEATH! NEVER WORK UNDER AN AUTOMOBILE THAT IS NOT PROPERLY SUPPORTED AND BLOCKED FROM ROLLING. NO CREDIT OR

More information

INSTALLATION OF WELLS SUPER QUICK CHUCK LEFT HAND ON RED WING LATHE

INSTALLATION OF WELLS SUPER QUICK CHUCK LEFT HAND ON RED WING LATHE DENTAL, INC. TECHNICAL BULLETIN Q824-022510 5860 FLYNN CREEK ROAD READ ALL INSTRUCTIONS P.O. BOX 106 BEFORE PROCEEDING COMPTCHE, CALIFORNIA, U.S.A. 95427 SAVE THIS FOR FUTURE REFERENCE www.wellsdental.com

More information

Horizontal and Vertical. Metal Cutting Band Saw MODEL: BS-115

Horizontal and Vertical. Metal Cutting Band Saw MODEL: BS-115 Horizontal and Vertical Metal Cutting Band Saw MODEL: BS-5 SAFETY. Know your band saw. Read the operator s Manual carefully. Learn the operations, applications and limitation.. Use recommended accessories.

More information

This manual will aid in the assembly of the FireBall V90 and FireBall X90. The assembly of both machines will be identical, unless specified.

This manual will aid in the assembly of the FireBall V90 and FireBall X90. The assembly of both machines will be identical, unless specified. This manual will aid in the assembly of the FireBall V90 and FireBall X90. The assembly of both machines will be identical, unless specified. Step #1 Lay all parts out to verify quantities. (2) 2 x 25-1/4

More information

TOOLS AND INSTALLATION

TOOLS AND INSTALLATION TOOLS AND INSTALLATION Safe, leak-free operation of any high-pressure system is dependent on correctly prepared and installed connections. This section outlines proper instructions for the machining and

More information

Removing and Replacing the Y-truck

Removing and Replacing the Y-truck Service Documentation Removing and Replacing the Y-truck To remove and replace the Y-truck you will need the following tools: 4mm Allen wrench 12mm stamped flat wrench #2 Phillips screwdriver (magnetic

More information

Installation Instructions. Installation Type

Installation Instructions. Installation Type Installation Instructions 800 & 8050 Slide Track Door Closers Non Hold Open & Hold Open Models Note: Hold open models are not permitted to be installed in Listed fire door assemblies. PULL SIDE MOUNTED

More information

w w w. h d o n l i n e s h o p. d e AUTOMATIC COMPRESSION RELEASE TOOL GENERAL INSTALLATION -J04654 REV Kit Number Models

w w w. h d o n l i n e s h o p. d e AUTOMATIC COMPRESSION RELEASE TOOL GENERAL INSTALLATION -J04654 REV Kit Number Models -J05 REV. 008-0- GENERAL Kit Number 98-08 Models AUTOMATIC COMPRESSION RELEASE TOOL For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com

More information

MODEL SK61732 COMPRESSOR SERVICE KIT

MODEL SK61732 COMPRESSOR SERVICE KIT MODEL SK61732 COMPRESSOR SERVICE KIT For use on 607 and 617 Model Compressors with.32 Stroke WARNING: Unplug the compressor before beginning disassembly. CAUTION: Improper assembly or use of damaged parts

More information

Char-Lynn Hydraulic Motor. Repair Information. R Series General Purpose Geroler Motor November, 1996

Char-Lynn Hydraulic Motor. Repair Information. R Series General Purpose Geroler Motor November, 1996 Char-Lynn Hydraulic Motor November, 1996 Repair Information General Purpose Geroler Motor 001 002 2 Geroler Motors Parts Drawing Bearing Race Needle Thrust Bearing Key Output Shaft Cap Screw -001 12 pt

More information

Grain Tank Cross Auger Trough Liner for John Deere 9400 / 9500 Combine

Grain Tank Cross Auger Trough Liner for John Deere 9400 / 9500 Combine www.polyskid.com P. O. Drawer 349, Monticello, GA. 31064 Phone: 800-542-7659, Fax: 706-468-2881 E-Mail: polytech@polyskid.com Grain Tank Cross Auger Trough Liner for John Deere 9400 / 9500 Combine FOR

More information

MODEL 36 Di-Acro Hand Shear

MODEL 36 Di-Acro Hand Shear OPERATOR S MANUAL & INSTRUCTIONS MODEL 36 Di-Acro Hand Shear Di-Acro, Incorporated PO Box 9700 Canton, Ohio 44711 3713 Progress Street N.E. Canton, Ohio 44705 330-455-1942 330-455-0220 (fax) Revised 01/02

More information

TK 1014 A POWER SHEAR

TK 1014 A POWER SHEAR TIN KNOCKER TK 1014 A POWER SHEAR Parts Diagram & Operating Instructions TAAG INDUSTRIES CORP. 1550 SIMPSON WAY, ESCONDIDO, CA 92029 Tel: (800) 640-0746 Fax: (760) 727-9948 Website: www.tinknocker.com

More information

Installation Instructions. Installation Type

Installation Instructions. Installation Type Installation Instructions 300 & 3050 Slide Track Door Closers Non Hold Open & Hold Open Models Note: Hold open models are not permitted to be installed in Listed fire door assemblies. PULL SIDE MOUNTED

More information

OTECO INC. MODEL ,000 PSI 4-1/16 PORT DM GATE VALVE MAINTENANCE MANUAL

OTECO INC. MODEL ,000 PSI 4-1/16 PORT DM GATE VALVE MAINTENANCE MANUAL Page 1 of 7 OTECO INC. MODEL 45 4 5,000 PSI 4-1/16 PORT DM GATE VALVE MAINTENANCE MANUAL Page 2 of 7 TABLE OF CONTENTS 1. Assembly Blowout 2. Repair Kit Contents & Technical Specifications 3. Disassembly

More information

COYOTE ENTERPRISES, INC. RIMLOC BLAST WHEEL MAINTENANCE & ASSEMBLY MANUAL

COYOTE ENTERPRISES, INC. RIMLOC BLAST WHEEL MAINTENANCE & ASSEMBLY MANUAL COYOTE ENTERPRISES, INC. RIMLOC BLAST WHEEL MAINTENANCE & ASSEMBLY MANUAL Parts & Machinery for the Abrasive Blast Industry 27301 East 121st Street Coweta, Oklahoma 74429 (918) 486-8411 Fax (918) 486-8412

More information

The Virgo/Libra Steam Engine

The Virgo/Libra Steam Engine The Virgo/Libra Steam Engine Congratulations on becoming the owner of a Virgo or Libra Steam Engine. With careful use and maintenance it will give many years of satisfying performance. Contents 1) Notes

More information

Installation Type. Edge of Door. Pull (Hinge) Side Mounted. Hinge Edge of Door. Push (Stop) Side Mounted

Installation Type. Edge of Door. Pull (Hinge) Side Mounted. Hinge Edge of Door. Push (Stop) Side Mounted Installation Instructions CAUTION An incorrectly installed or improperly adjusted door closer can cause property damage or personal injury. These instructions should be followed to avoid the possibility

More information

INSTRUCTION MANUAL IM 251 For Gas Turbine Tensioned Studs and Nuts VENDOR SUPPLIED

INSTRUCTION MANUAL IM 251 For Gas Turbine Tensioned Studs and Nuts VENDOR SUPPLIED INSTRUCTION MANUAL IM 251 For Gas Turbine Tensioned Studs and Nuts Note: This manual is written specifically for connections that employ the use of Load Coupling Spacers placed under the nuts. If spacers

More information

DYNATRAC BALL JOINT REBUILD INSTRUCTIONS V4.0

DYNATRAC BALL JOINT REBUILD INSTRUCTIONS V4.0 DYNATRAC PRODUCTS 2007-2016 4X4 JEEP JK HEAVY DUTY BALL JOINT JP44-2X3050-C DYNATRAC BALL JOINT REBUILD INSTRUCTIONS V4.0 WARNING: Improper use or installation of this product can cause major failures

More information

No November, Char-Lynn. Hydraulic Motor. Repair Information. R Series General Purpose Geroler Motor

No November, Char-Lynn. Hydraulic Motor. Repair Information. R Series General Purpose Geroler Motor Char-Lynn Hydraulic Motor No. 7-142 November, 1996 Repair Information General Purpose Geroler Motor 001 002 2 Geroler Motors Parts Drawing Bearing Race Needle Thrust Bearing Key Output Shaft Cap Screw

More information

HARDINGE Installation booklet For: Dead-Length Collet Adaptation Chucks Stationary Collet

HARDINGE Installation booklet For: Dead-Length Collet Adaptation Chucks Stationary Collet HARDINGE Installation booklet For: Dead-Length Collet Adaptation Chucks Stationary Collet Read the enclosed instructions and recommendations before any installations CONTENTS Dead-Length Collet Adaptation

More information

Maintenance Information

Maintenance Information 16601023 Edition 2 January 2014 Air Impact Wrench 2705P1 Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these

More information

pneumatic c-ring tool

pneumatic c-ring tool pneumatic c-ring tool hc5 HC5 WARNINGS! Always read tool manual before operating tool. Always wear safety glasses when operating or while in the area where a tool is being used. When test cycling tool

More information

DYNATRAC BALL JOINT REBUILD INSTRUCTIONS V5.0

DYNATRAC BALL JOINT REBUILD INSTRUCTIONS V5.0 DYNATRAC PRODUCTS 2007-2018 JEEP JK HEAVY DUTY BALL JOINT JP44-2X3050-C DYNATRAC BALL JOINT REBUILD INSTRUCTIONS V5.0 WARNING: Improper use or installation of this product can cause major failures that

More information

Referencing 0,0 position

Referencing 0,0 position Page 1 of 11 TITLE: SABRE X-Axis Lead Screw Replacement Procedure Gerber FastFact #: 2013 Supplied by: Gerber Hardware Support Last Modified: March 1, 2011 Summary: The following procedure explains how

More information

ASSA ABLOY Series Installation Instructions. Regular Arm. Parallel Arm. Top Jamb Mount. Multi-Sized 1 thru 6 Non-Hold Open and Hold Open Models

ASSA ABLOY Series Installation Instructions. Regular Arm. Parallel Arm. Top Jamb Mount. Multi-Sized 1 thru 6 Non-Hold Open and Hold Open Models 9500 Series Installation Instructions Multi-Sized 1 thru 6 Non-Hold Open and Hold Open Models Regular Pages 5 & 6 Parallel Pages 7 & 8 Top Jamb Mount Pages 9 & 10 IMPORTANT: An improperly installed or

More information

PROSTEER BALL JOINT REBUILD INSTRUCTIONS V1.0

PROSTEER BALL JOINT REBUILD INSTRUCTIONS V1.0 DYNATRAC PRODUCTS 2003-2010 4X4 DODGE 2500/3500 HEAVY DUTY BALL JOINT PROSTEER BALL JOINT REBUILD INSTRUCTIONS V1.0 WARNING: Improper use or installation of this product can cause major failures that could

More information

SAFETY INSTRUCTIONS. Wear protective clothing, including safety glasses and steel toe boots.

SAFETY INSTRUCTIONS. Wear protective clothing, including safety glasses and steel toe boots. SAFETY INSTRUCTIONS Wear protective clothing, including safety glasses and steel toe boots. DO NOT allow loose clothing or long hair near machine operations. Keep work site and machine clean. Use brush

More information

Motorized M3 AX7200 Rotary-Style Gasket Cutter Operating Instructions

Motorized M3 AX7200 Rotary-Style Gasket Cutter Operating Instructions Motorized M3 AX7200 Rotary-Style Gasket Cutter Operating Instructions INTRODUCTION Congratulations! You are the owner of the finest rotary-style gasket cutter in the world. Originally developed and patented

More information

INSTRUCTIONS FOR HIT LOCK MORTISER

INSTRUCTIONS FOR HIT LOCK MORTISER 1825 VIA BURTON ANAHEIM CA 92806 714-772-5202 / FAX 714-772-2302 EMAIL: MAIL@MAJORMFG.COM WEB: WWW.MAJORMFG.COM INSTRUCTIONS FOR HIT-66-200 LOCK MORTISER WHEN USING POWER TOOLS ALWAYS WEAR EYE AND EAR

More information

H8508 Impact Wrench SERVICE MANUAL. Model (Serial Code FWN) Model (Serial Code FWP)

H8508 Impact Wrench SERVICE MANUAL. Model (Serial Code FWN) Model (Serial Code FWP) SERVICE MANUAL H8508 Impact Wrench Model 48755 (Serial Code FWN) Model 48760 (Serial Code FWP) Read and understand all of the instructions and safety information in this manual before operating or servicing

More information

Side Winder R o u t e r L i f t.

Side Winder R o u t e r L i f t. Woodpeckers PRECISION WOODWORKING TOOLS Side Winder R o u t e r L i f t. INSTALLATION INSTRUCTIONS The wrench handle must be pointing left in order to fully insert or remove it. Lift Wrench Once fully

More information

Big Block Installation Manual For Systems without A/C

Big Block Installation Manual For Systems without A/C Big Block Installation Manual For Systems without A/C Billet Specialties, Inc. 500 Shawmut Ave. La Grange, IL 60526 Tech Line (708) 588-0505 Fax (708) 588-7181 Hardware List For Chevrolet Big Block Tru

More information

MUELLER GAS. DH-5/EH-5 Drilling. Reliable Connections. DH-5 Drilling Machine General Information 2. EH-5 Drilling Machine General Information 3

MUELLER GAS. DH-5/EH-5 Drilling. Reliable Connections. DH-5 Drilling Machine General Information 2. EH-5 Drilling Machine General Information 3 operating Instructions manual MUELLER GAS TAble of contents PAGE DH-5 Drilling Machine General Information 2 DH-5/EH-5 Drilling EH-5 Drilling Machine General Information 3 Operating Instructions 4-5 DH-5

More information

DP-8 H. H. MØRCH. Instructions. Contents of the packing. Spatial requirements. Mounting the bush

DP-8 H. H. MØRCH. Instructions. Contents of the packing. Spatial requirements. Mounting the bush DP-8 Instructions H. H. MØRCH Contents of the packing In the packing of the tonearm you will find the arm base in which the bearings are encapsulated in a heavy body. This is the link between the moveable

More information

PREVIEW COPY. Table of Contents. Lathe Setup and Workpiece Preparation...3. Lesson Two Rough Turning and Finish Turning...19

PREVIEW COPY. Table of Contents. Lathe Setup and Workpiece Preparation...3. Lesson Two Rough Turning and Finish Turning...19 Table of Contents Lesson One Lathe Setup and Workpiece Preparation...3 Lesson Two Rough Turning and Finish Turning...19 Lesson Three Lesson Four Boring and Counterboring...35 Cutting Internal Threads and

More information

BHJ Products, Inc. Parts List & Instructions

BHJ Products, Inc. Parts List & Instructions Product Name: Lifter-Tru Kit for Ford Windsor & SVO Small Block V8 Page 1 of 5 Kit Contents: 2x End Plates 2x 5/8 Threaded Adjustment Sleeves 1x Front Angle Bracket 2x 5/8 Adjustment Sleeve Spacers * 1x

More information

No September, Char-Lynn. Power Steering. Repair Information. 20 Series Steering Control Unit 001

No September, Char-Lynn. Power Steering. Repair Information. 20 Series Steering Control Unit 001 Char-Lynn Power Steering No. 7-313 September, 1997 Repair Information 20 Series Steering Control Unit 001 Bearing Race Retaining Ring Needle Thrust Bearing Bearing Race Seal Ring Backup Washer Seal (3

More information

BHJ Products, Inc. Parts List & Instructions

BHJ Products, Inc. Parts List & Instructions Product Name: Lifter-Tru Kit for General Motors LS V8 Page 1 of 5 Kit Contents: 2x End Plates 2x Threaded Adjustment Sleeves 1x Front Angle Bracket 2x M10-1.5 x 65 Hex Head Bolts * 2x Angle Adapter Blocks

More information

DC3210. Recommended Closer Size

DC3210. Recommended Closer Size Installation Instructions For Non-Hold Open or A Hold Open Arm Option DC3200 Series Multi-Sized thru 6 Regular Arm Universal Door Closers Parallel Arm Jamb Mount See pages 2&3 See pages 4&5 See pages 6&7

More information

PNEUMATIC C-RING TOOLS SC73462 SAFETY INSTRUCTIONS. WARNINGS Always read tool manual before operating.

PNEUMATIC C-RING TOOLS SC73462 SAFETY INSTRUCTIONS. WARNINGS Always read tool manual before operating. PNEUMATIC C-RING TOOLS SC73462 SAFETY INSTRUCTIONS WARNINGS Always read tool manual before operating. Always wear safety glasses while operating or while in the vicinity of a tool in operation. For testing,

More information

MM340 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS

MM340 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS MM30 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.

More information

Instructions for the installation of Ellison Bronze balanced door models #137 & 138

Instructions for the installation of Ellison Bronze balanced door models #137 & 138 1. A packing list will be found in crate No. 1 of each shipment. The parts in the crates should be checked with this list. If there is any discrepancy, notify Ellison Bronze at once. 2. All parts are numbered.

More information

MantelMount. TM1A Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS

MantelMount. TM1A Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS MantelMount TMA Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS TM Thank you for choosing the MantelMount television wall mount. Please read this entire manual before

More information

3 Emergency Breakaway Coupling

3 Emergency Breakaway Coupling SM64227 July 2008 Applicable addition manuals: N/A Aerospace Group Conveyance Systems Division Carter Ground Fueling Maintenance & Repair Manual 3 Emergency Breakaway Coupling Model 64227 Table of Contents

More information

Band-Master ATS Nano Pneumatic Banding Tool Operating Instructions

Band-Master ATS Nano Pneumatic Banding Tool Operating Instructions Band-Master ATS 601-118 Nano Pneumatic Banding Tool CONTENTS 601-118 Overview... 3 Safety.... 5 Initial Tool Set-up... 5 Regulator assembly mounting... 5 Attach tool head to regulator.... 6 Operating instructions...

More information

It s a good idea to identify the Front and Rear cylinder heads. before starting the teardown process.

It s a good idea to identify the Front and Rear cylinder heads. before starting the teardown process. It s a good idea to identify the Front and Rear cylinder heads using a paint pen before starting the teardown process. Use a 17/64 drill bit (or 6mm if you have metric drills or round stock) to lock the

More information

DELUXE HIGH SECURITY SET LKM116 INSTRUCTIONS

DELUXE HIGH SECURITY SET LKM116 INSTRUCTIONS DELUXE HIGH SECURITY SET LKM116 INSTRUCTIONS S&G 8400/8500 DRILL GUIDE LKM115 INSTRUCTIONS X-O7 Dial Puller & Drill Guide Components X-O7 DIAL SPACER RING Puller cup cup handle Spindle bolt Puller bolt

More information

T : F : Revised June 2013

T : F : Revised June 2013 Revised June 2013 W R A, O USA T: 800 321 7950 440 998 2788 F: 440 992 2925... 2 INSTRUCTIONS FOR 3/4, 1, 1-1/4 DIAMETER TAPS FIGURE 1 A B C D E F G HOT TAP SPINDLE HOT TAP SLEEVE HOT TAP FEED SCREW ADAPTER

More information

meaden New Generation Tooling & Operations Manual

meaden New Generation Tooling & Operations Manual 06-19-01 New Generation Tooling & Operations Manual 210 West 83rd Street Burr Ridge, Illinois 60527 Telephone: 630/655-0888 FAX: 630/655-3012 www.printing.com INTRODUCTION Table of Contents I. ENGAGEMENT

More information

Crankshaft Gear Modification and Assembly Procedures

Crankshaft Gear Modification and Assembly Procedures 652 Oliver Street Williamsport, PA 17701 U.S.A. Tel. 570-323-6181 Fax. 570-327-7101 www.lycoming.textron.com MANDATORY SERVICE BULLETIN DATE: January 30, 2003 Service Bulletin No. 475C (Supersedes Service

More information

Pressure Vessel Assembly Instructions

Pressure Vessel Assembly Instructions Pressure Vessel Assembly Instructions 1) Measure aluminum tube outer diameter 2) Machine both end caps and only drill pilot holes for all hoes shown 3) Weld both end caps onto the aluminum tube and be

More information

JARVIS. Model Brisket Scissor EQUIPMENT... TABLE OF

JARVIS. Model Brisket Scissor EQUIPMENT... TABLE OF Model 423-17 Brisket Scissor EQUIPMENT SELECTION... Ordering No. TABLE OF CONTENTS... Page Model 423--17... 4037003 Air Filter / Regulator / Lubricator 3022003 Air Hose Assembly... 3059018 Balancer...

More information