Duro H321-V, 3605-H321-V, 3606-H321-V Duro Shower System Series Operation & Maintenance Manual. Options/Modifications. Compliance.

Transcription

1 uro 60--V, 605--V, 606--V uro Shower System Series peration & aintenance anual odel umbers 60--V and Shower System 605--V Shower/and Shower System 606--V Tub/Shower/and Shower System ptions/odifications S -W -V -SS -T76 -X -S -ST -T.5 gpm (5.7 /min) flow restrictor.0 gpm (7.6 /min) flow restrictor /" female S connections Wide lever handle (chrome finish only) everse coring, hot on right, cold on left, for back to back installations Slip spout on any tub and shower unit 6" slide bar/grab bar with hand shower in place of standard hand shower unit ntegral service stops - allows water shutoff at valve for service ntegral check stops - for use in installations where a positive shut-off device is used downstream of mixing valve Satin ickel finish Trim only, valve not included Specification 60--V and shower system powered by the Temptrol pressure balancing valve. eatures adjustable stop screw to limit handle turn, lever handle, wall connection, 0" slide bar, in-line vacuum breaker, flexible metal hose, mode hand shower and standard.5 gpm (9.5 /min) flow restrictor V Shower/hand shower system powered by the Temptrol pressure-balancing valve. eatures adjustable stop screw to limit handle turn, separate two function diverter, lever handle, wall connection, 0" slide bar, in-line vacuum breaker, flexible metal hose, mode hand shower, mode showerhead and standard.5 gpm (9.5 /min) flow restrictors V Tub/shower/hand shower system powered by the Temptrol pressure balancing valve. eatures adjustable stop screw to limit handle turn, separate three function diverter, lever handle, wall connection, 0" slide bar, in-line vacuum breaker, flexible metal hose, non-diverter tub spout, mode hand shower, mode showerhead with standard.5 gpm (9.5 /min) flow restrictors. omponents made from metal and nonmetallic materials plated in standard polished chrome finish. ompliance -S.8./S 5. Warranty ote: ppend appropriate -suffix to model number. imited ifetime - to the original end purchaser in consumer/residential installations. 5 Years - for industrial/commercial installations. efer to for complete warranty information.

2 imensions 606--V-T TU easurements Ø -/", 57 mm 5-7/8", 9 mm 6", 5 mm ale /" T thread must be recessed /" (6 mm) from finished wall ef. 77", 956 mm -/", 89 mm 5", 7 mm 7-/", 9 mm Ø -/", 6 mm ef. 0", 5 mm (606) ef. ", 8 mm (60, 605) ef. ", 067 mm ef. ", 05 mm -/6", 8 mm -7/6", 87 mm ough-in -/8" ± /", 60 mm ± mm 5-/", mm 7", 78 mm /" T otes: ) ll dimensions measured from nominal rough-in (see as reference). ) imensions subject to change without notice.

3 arts reakdown eplacement arts tem escription art umber Showerhead 6S T Water Supply Water Supply S Shower rm 00S lange andle ssembly T-67 ome over TS-07 iverter scutcheon Screws TS-00 ounting late scutcheon Screws ounting late TS-00 Tub Spout 067 Slide ar -009 ssembly and Shower -00 Wall lbow -05 Vacuum reaker -0 S 60 ose otes: ) ppend -ST to part number for Satin ickel finish. ) ppend -.5 or -.0 to showerhead or hand shower for low flow. Tools equired for nstallation otes: ) pply a bead of silicone around the perimeter of all shower trim installed flush to the finished wall (less mounting plates and brackets). eave opening on bottom of escutcheons for weep hole. ) pply plumber tape to all threaded connections. djustable wrench llen wrench: /8" hillips head screwdriver lumber tape ower drill Silicone

4 nstallation ote: or valve body installation, please see valve body installation guides. ) nstall small mounting plate () to diverter valve (V-Y or V-Y) and large mounting plate () to shower valve (000- Y). Secure each with two screws () and (). ) ttach shower escutcheon () to large mounting plate (). 5) nstall diverter handle (605 and 606 only) () and shower handle () to valves. Secure handles by tightening set screws. ote: Tabs should snap into place. ) nstall dome covers () to valves by turning clockwise. ote: andles should be facing the 6 o'clock position. ) ttach diverter escutcheon () to small mounting plate (). 6) nstall tub spout () to stub out pipe. Turn clockwise to secure. ote: Tabs should snap into place.

5 nstallation 7a) ry Wall ption: emove upper and lower caps () from slide bar brackets. lace slide bar () into desired position. Using brackets as a guide, carefully drill /6" holes into wall. emove slide bar and install anchors. 7b) Stud ption: emove upper and lower caps () from slide bar brackets. lace slide bar () into desired position. Using brackets as a guide, carefully drill /8" pilot holes into stud. 8) With slide bar () in position, secure to wall using screws (). eplace upper and lower caps () onto slide bar brackets. otes: ake sure that slide bar holes and bracket holes are aligned before drilling. efore drilling bottom hole, make sure slide bar is plumb. otes: ake sure that slide bar holes and bracket holes are aligned before drilling. efore drilling bottom hole, make sure slide bar is plumb. 5

6 nstallation 9) nstall wall elbow () to stub out pipe. Tighten set screw to secure. 0) ttach shower arm () and flange () to vertical shower pipe turning clockwise to tighten. ) nstall showerhead () to shower arm (). Turn clockwise to tighten. ) ttach large end of hand shower hose (S) to hand shower wand (). ttach small end of hand shower hose (S) to vacuum breaker (). onnect vacuum breaker to wall elbow (). Turn clockwise to tighten. S S peration (Temperature ontrol) ) Turn shower handle counterclockwise approximately / turn to put valve in cold position. ) Turn shower handle counterclockwise approximately / turn to put valve in warm position. ) Turn shower handle counterclockwise approximately / turn to put valve in hot position. 6

7 peration (iverter ontrol: V-Y) ) artridge is factory set to divert to function. ) Turn handle to position to divert to function. ) Turn handle to position to share functions and. ST ST ST ote: dditional handle positions for same output are illustrated. peration (iverter ontrol: V-Y) ) artridge is factory set to divert to function. ) Turn handle to position to divert to function. ) Turn handle to position to divert to function. ST ST ST ) Turn handle to position to share functions and. 5) Turn handle to position 5 to share functions and. 6) Turn handle to position 6 to share functions and. ST ST 5 ST 6 Troubleshooting hart inish is spotting. Troubleshooting hart lements in water supply may cause water staining on finish. lean finished trim area with a soft cloth using mild soap and water or a non-abrasive cleaner and then quickly rinse with water. or alifornia esidents W: This product contains chemicals known to the State of alifornia to cause cancer, birth defects, or other reproductive harm. Symmons ndustries, nc. rooks rive raintree, 08 hone: (800) ax: (800) opyright 06 Symmons ndustries, nc. gethelp@symmons.com ZV-07 V 006