M MODULAR PARTS T01-A INSTALLATION INSTRUCTIONS MIRRORED CABINET W/DEFOGGER K-15512T , 2011 Copyright Kohler China Ltd.

Transcription

1 M M MODULAR INSTALLATION INSTRUCTIONS ( ) MIRRORED CABINET W/DEFOGGER K-15512T BEFORE YOU BEGIN Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences. Follow the sections that pertain to your particular installation. This will help you avoid costly mistakes. In addition to proper installation, read all operating and safety instructions. All information in these instructions is based upon the latest product information available at the time of publication. Kohler China. reserves the right to make changes in product characteristics, packaging, or availability at any time without notice. These instructions contain important care, cleaning, and warranty information-please leave instructions for the consumer. Before installation carefully inspect the new fixture for any signs of damage. PARTS WARNING: Risk of injury or product damage. Tempered glass cannot be cut. WARNING: Don't use acidic or alkalic cleaners or alcohol to clean the wooden surface. Use a dampened cloth to clean. Parts supplied with your cabinet. (For cabinet body and door replacement, call customer service with model number.) Be sure to check the cardboard supports in the carton, glass parts are packed in them. ACCESSORIES LIST - Glass Shelves X3 Wall Anchors X5 Top Clips X2 Caps of Screw X10 Screws X5 Hole Plugs X40 Mounting Bar X1 Snap-in Pins X12 Screws ST ST X8 Connector Block X2 Hinge Clips X2 Glass X1 2 Level Box X1 Tissue Box X , 2011 Copyright Kohler China Ltd., 2011

2 ROUGHING-IN UNIT : mm PRE-DRILLED HOLE Pre-Drilled Hole for Side Kits Pre-Drilled Hole for Recessed Cabinet Pre-Drilled Hole for Cabinet-to-Cabinet -2-

3 745mm high 745mm INSTALLATION NOTE The cabinet has two ways of installation: Recessing mounting. Surface mounting. Refer to the following instruction for mirror installation. RECESSING THE MIRRORED CABINET INTO THE WALL The Vertical installation changes the width of the roughout. Please refer to the picture below. 472mm for Width 472mm Screws Fig. 1 1 On installations of larger cabinet in combinations of 3 or more, the center door, when open, may cause the cabinet to bow from the wall. If this happens, drill a hole at the location shown in Figure J and install a ST3.5X35 SCREW. 3 ST3.5X35 Figure J 3/4" (19.1mm) 3/4" (19.1mm) Drill a hole through Top of middle cabinet 3/4" (19.1 mm) from back 19.1mm 1-3-

4 Install screws through holes in mirrored cabinet as shown in Fig.1, Note: DO NOT OVER- TIGHTEN! Use s crews. Top View Stud and wall surface Mirrored cabinet flange fits flush against wall Install dome caps over screws SURFACE MOUNTING THE MIRRORED CABINET ON A WALL Fig NOTE: Install the side kits while surface mounting the mirrored cabinet on the wall, additional order of the side kits. As shown in Fig 3, drill two 2-5mm holes in bottom mounting bar at indent location, then drill 4-6mm holes in wall at locations shown in Fig 3, insert wall anchors Drill holes 4-6mm 4-6mm 750 Fix the mounting bar to the wall, level the mounting bar. The highest point of table 20 Screws & Wall anchor Fig

5 Sit the mirrored cabinet on the mounting bar, then lower and tighten the screws into place, as shown in Fig.4. 4 Top clip for surface mount 2 per cabinet Top of cabinet frame member 2 Top clips 2 WALL Top clips slide into this screw channel from center opening. Screws & Wall anchor Fig. 4 4 COMBINATION INSTALLATION OF SEVERAL MIRRORED CABINETS 2 Connect the cabinets by fixing the connector blocks to the side of the mirrored cabinet with ST4.2x12 screws. ST4.2x12 For surface mounting installation, please fix the side kits bracket at the two sides of the combined cabinets with M4 screws. M4 Connector Blocks Mirrored Cabinet Mirrored Cabinet Mirrored Cabinet Side Kits Fig T01-A -5-

6 Door adjustments Remove the hinge cover or the blumotion before adjustion, see Fig 6A. 6A Adjust the hinge of door in 3 directions to make sure the door level as shown in Fig.6B. 6B Assemble Assemble Fig. 6A Assemble Removal 6A Removal Height Adjustment Depth Adjustment Side Adjustment Fig. 6B 6B If no light kit is installed, the hinge clips are not necessary and the door can be allowed to swing 170. If the door hinges come with a 110 black plastic hinge clips are required, snap the hinge clip over the elbow of the hinge into the holes located on the hinge Fig

7 Put the tissue box, 2 level box and the glass into the cabinet as shown in Fig.8. Fig Push/twist the pins into place & Fill the remaining holes with the plugs & Push one side of the shelf into the left or right clips. Snap the shelf down into the opposite side. If the shelf is too tight, repeat the process from the other side. A B Fig. 9 9 Fig

8 The step is only for the installation of defogger. See Fig 11, external power supply. (220V/50HZ) 220V/50HZ Fig USER MAINTENANCE Warn! Risk of product damage Many cleansers contain abrasive and chemical substance which is not suitable for cleaning stainless steel, enamel, plating or plastic products. You may use mild cleansers or soaps to clean the surfaces. Wipe any splashes of cleaner solutions from the surface with clean soft cloth. Maintain ventilation in the bathroom, and separate the dry area from the damp one if conditions permit. Try to open the door and windows of the bathroom and maintain good ventilation. Kohler mirrored cabinet are dealt with strict procedures for damp-proof, whose good damp-proof function ensures good performance even in bathroom of huge humidity. Yet do not splash and pour water directly on the mirrored cabinet. Make sure that the bathroom is not over damp and wipe any splashes from surfaces immediately. Maintenance of door board: Clean and wipe door board regularly, and wipe the condensation vapor with dry and soft cloth. 5. The mirrored cabinet door and interior are constructed of mirror and aluminum. Use only a damp cloth to clean. Spray the cloth, not the mirror when cleaning. Mirrors are damaged by the use of ammonia or vinegar based cleaners. Rubbing alcohol can be used for stubborn stains. 6. Use no abrasive cleansers on any part of the mirrored cabinet. 7. The white frame should be cleaned with a damp cloth only