Dia H321-V, 3505-H321-V, 3506-H321-V Shower System Series Operation & Maintenance Manual. Options/Modifications. Compliance.

Transcription

1 ia 50--V, 505--V, 506--V Shower System Series peration & aintenance anual odel umbers 50--V and Shower System 505--V Shower/and Shower System 506--V Tub/Shower/and Shower System ptions/odifications elete Suffix -ST -T ompliance -AS A.8./SA 5. Warranty.5 gpm (5.7 L/min) flow restrictor.0 gpm (7.6 L/min) flow restrictor hrome plastic escutcheon on valve with color graphics/indicators in place of standard brass escutcheon Satin ickel finish Trim only, valve not included ote: Append appropriate -suffix to model number. Specification 50--V and shower system powered by the Temptrol pressure balancing valve. Features adjustable stop screw to limit handle turn, lever handle, wall connection, 0" slide bar, flexible metal hose and mode hand shower with backflow prevention, and standard.5 gpm (9.5 L/min) flow restrictor V Shower/hand shower system powered by the Temptrol pressure-balancing valve. Features adjustable stop screw to limit handle turn, separate two function diverter, lever handle, wall connection, 0" slide bar, flexible metal hose and mode hand shower with backflow prevention, mode showerhead and standard.5 gpm (9.5 L/min) flow restrictors V Tub/shower/hand shower system powered by the Temptrol pressure balancing valve. Features adjustable stop screw to limit handle turn, separate three function diverter, lever handle, wall connection, 0" slide bar, flexible metal hose and mode hand shower with backflow prevention, non-diverter tub spout, mode showerhead with standard.5 gpm (9.5 L/min) flow restrictors. omponents made from metal and nonmetallic materials plated in standard polished chrome finish. Limited Lifetime - to the original end purchaser in consumer/residential installations. 5 Years - for industrial/commercial installations. efer to for complete warranty information.

2 imensions A F easurements A Ø -/", 6 mm 6-/", 7 mm 6", 5 mm ale /- PT thread must be recessed /" (6 mm) from finished wall ef. 77", 956 mm F -/", mm Ø 5", 7 mm Ø 7-/", 9 mm Ø -/", 6 mm ef. 0", 5 mm ef. ", 8 mm L ef. ", 05 mm ", 76 mm -7/8", 7 mm ough-in -/8" ± /", 60 mm ± mm P 5-/", mm 7", 78 mm L P FL otes: ) All dimensions measured from nominal rough-in (see as reference). ) imensions subject to change without notice.

3 Parts reakdown L A F P T Water Supply L Water Supply otes: ) Apply a bead of silicone around the perimeter of all shower trim installed flush to the finished wall. Leave opening on bottom of escutcheons for weep hole. ) Apply plumber tape to all threaded connections. *rder in-line vacuum breaker (F-09) for hand shower systems without dual checks. eplacement Parts tem escription Part umber A Showerhead 5S Shower Arm 00S Flange andle Assembly T-A ome over T-9/0 F iverter scutcheon Screws T-6A ounting Plate scutcheon Screws ounting Plate TS-009 (rass) TS-00 (Plastic) L Tub Spout 067 Slide ar Assembly A-009 P and Shower F-00 Wall lbow F-05 60" ose TS-05 otes: ) Append appropriate -suffix for premium finish. ) Append -.5 or -.0 to showerhead or hand shower for low flow. Tools equired for nstallation Adjustable wrench Allen wrench: andle (mm) Phillips head screwdriver Plumber tape F-09* Power drill Silicone

4 nstallation ote: For valve body installation, please see valve body installation guides. ) nstall small mounting plate () to diverter valve (V-Y or V-Y) and large mounting plate () to shower valve (6-- Y). Secure each with two screws () and (). ) Attach shower escutcheon () to large mounting plate (). 5) nstall diverter handle (505 and 506 only) () and shower handle () to valves. Secure handles by tightening set screws. ote: Tabs should snap into place. ) nstall dome covers () to valves by turning clockwise. ote: andles should be facing the 6 o'clock position. ) Attach diverter escutcheon (F) to small mounting plate (). 6) nstall tub spout (L) to stub out pipe. Turn clockwise to secure. F L ote: Tabs should snap into place.

5 nstallation 7a) ry Wall ption: emove upper and lower caps () from slide bar brackets. Place slide bar () into desired position. Using brackets as a guide, carefully drill /6" holes into wall. emove slide bar and install anchors. 7b) Stud ption: emove upper and lower caps () from slide bar brackets. Place slide bar () into desired position. Using brackets as a guide, carefully drill /8" pilot holes into stud. 8) With slide bar () in position, secure to wall using screws (). eplace upper and lower caps () onto slide bar brackets. otes: ake sure that slide bar holes and bracket holes are aligned before drilling. efore drilling bottom hole, make sure slide bar is plumb. otes: ake sure that slide bar holes and bracket holes are aligned before drilling. efore drilling bottom hole, make sure slide bar is plumb. 5

6 nstallation 9) nstall wall elbow () to stub out pipe. Tighten set screw to secure. ) nstall showerhead (A) to shower arm (). Turn clockwise to tighten. ) Attach large end of hand shower hose () to hand shower wand (P). Attach small end of hand shower hose () to wall elbow (). Turn clockwise to tighten. A P 0) Attach shower arm () and flange () to vertical shower pipe turning clockwise to tighten. peration (Temperature ontrol) ) Turn shower handle counterclockwise approximately / turn to put valve in cold position. ) Turn shower handle counterclockwise approximately / turn to put valve in warm position. ) Turn shower handle counterclockwise approximately / turn to put valve in hot position. 6

7 peration (iverter ontrol: V-Y) ) artridge is factory set to divert to function. ) Turn handle to position to divert to function. ) Turn handle to position to share functions and. PST PST PST ote: Additional handle positions for same output are illustrated. peration (iverter ontrol: V-Y) ) artridge is factory set to divert to function. ) Turn handle to position to divert to function. ) Turn handle to position to divert to function. PST PST PST ) Turn handle to position to share functions and. 5) Turn handle to position 5 to share functions and. 6) Turn handle to position 6 to share functions and. PST PST 5 PST 6 Troubleshooting hart Finish is spotting. Troubleshooting hart lements in water supply may cause water staining on finish. lean finished trim area with a soft cloth using mild soap and water or a non-abrasive cleaner and then quickly rinse with water. WA: This product can expose you to chemicals including lead, which is known to the state of alifornia to cause cancer, birth defects, or other reproductive harm. For more information, go to Symmons ndustries, nc. rooks rive raintree, A 08 Phone: (800) Fax: (800) opyright 08 Symmons ndustries, nc. symmons.com gethelp@symmons.com ZV-07 V A 088