Duro Shower/Hand Shower System Operations & Maintenance Manual. Warranty Duro Shower/Hand Shower System

Transcription

1 uro 605 hower/and hower ystem perations & aintenance anual odel umbers 605 uro hower/and hower ystem odifications gpm (5.7 L/min) flow restrictor pecifications hower/hand shower system powered by the Temptrol ressure alancing valve. Features 0" slide bar, separate two function diverter, in-line vacuum breaker, 60" flexible metal hose, mode hand shower, mode showerhead and standard.5 gpm (9.5 L/min) flow restrictors. omponents made from metal and nonmetallic materials plated in standard polished chrome finish. ompliance -A A.8./A 5. - Wide, square lever handle - tacked, square lever handle - Round, mode showerhead - Round, mode showerhead - quare, mode showerhead Warranty Limited Lifetime - to the original end purchaser in consumer/residential installations. 5 Years - for industrial/commercial installations. Refer to for complete warranty information. ote: Append appropriate -suffix to model number.

2 imensions A I L F easurements A Ø /", 6 mm 6", 5 mm 6", 5 mm right or left ale /- T thread must be recessed /" from finished wall 77", 956 mm F /", 89 mm 5", 7 mm 7 /", 9 mm I 0", 5 mm ", 067 mm /8", 79 mm L /", 89 mm Rough-in /8" ± /", 60 mm ± mm 6 /", 7 mm 6 /", 7 mm 5 5/8", mm /8", 80 mm R 5/8", 9 mm /8", 79 mm T 5/8", 9 mm Floor R - T otes: ) All dimensions measured from nominal rough-in (see as reference). ) imensions are subject to change without notice.

3 arts reakdown Replacement arts Item escription art umber A L F I A In-line Vacuum reaker F-0 & 60" ose Wall lbow F-05 I and hower F-00 lide ar Assembly -5 hower Arm 00 Flange howerhead 6 (-) Round, ode howerhead 5 Round, ode 5- (-) howerhead quare, ode 6 (-) howerhead F iverter scutcheon crews T-55- ounting late asket crews L scutcheon T ounting late asket andle Assembly T-67 Wide, quare Lever RT-09 (-) andle tacked, quare RT-09 (-) Lever andle ome over RT Tools Required for Installation Adjustable wrench - - Allen wrench (/8 ) hillips head screwdriver lumber tape otes: ) Apply a bead of silicone around the perimeter of all shower trim installed flush to the finished wall. Leave opening on bottom of escutcheon for weep hole. ) Apply plumber tape to all threaded connections. ower drill ilicone

4 Installation ote: For valve body installation, please see valve body installation guides. ) Attach shower escutcheon (L) to large mounting plate (). 5) Install diverter handle () and shower handle () to valves. ecure handles by tightening set screws. ) Install small mounting plate () to diverter valve and large mounting plate () to shower valve (6-- Y). ecure each with two screws (). L ote: Tabs should snap into place. ) Install dome covers () to valves by turning clockwise. ote: andles should be facing the 6 o'clock position. ) Attach diverter escutcheon (F) to small mounting plate (). F ote: Tabs should snap into place.

5 Installation 7a) ry Wall ption: Remove upper and lower caps () from slide bar brackets. lace slide bar () into desired position. Using brackets as a guide, carefully drill /6" holes into wall. Remove slide bar and install anchors. 7b) tud ption: Remove upper and lower caps () from slide bar brackets. lace slide bar () into desired position. Using brackets as a guide, carefully drill /8" pilot holes into stud. 8) With slide bar () in position, secure to wall using screws (). Replace upper and lower caps () onto slide bar brackets. otes: ake sure that slide bar holes and bracket holes are aligned before drilling. efore drilling bottom hole, make sure slide bar is plumb. otes: ake sure that slide bar holes and bracket holes are aligned before drilling. efore drilling bottom hole, make sure slide bar is plumb. 5

6 Installation 9) Install wall elbow () to stub out pipe. Tighten set screw to secure. ) Install showerhead () to shower arm (). Turn clockwise to tighten. ) Attach large end of hand shower hose () to hand shower (I). Attach small end of hand shower hose () to in-line vacuum breaker (A). onnect in-line vacuum breaker to wall elbow (). Turn clockwise to tighten. I 0) Attach shower arm () and flange () to vertical shower pipe turning clockwise to tighten. A 6

7 peration Temperature ontrol iverter ontrol ) Turn shower handle counterclockwise approximately / turn to put valve in cold position. ) artridge is factory set to divert to function. ) Turn shower handle counterclockwise approximately / turn to put valve in warm position. ) Turn handle to position to divert to function. ) Turn shower handle counterclockwise approximately / turn to put valve in hot position. ) Turn handle to position to share functions and. ote: Additional handle positions for same output are illustrated. are and leaning ) lean finished trim area with a soft cloth using mild soap and water or a non-abrasive cleaner and then quickly rinse with water. Troubleshooting hart roblem ause olution Finish is spotting. lements in water supply may cause water staining on finish. lean finished trim area with a soft cloth using mild soap and water or a non-abrasive cleaner and then quickly rinse with water. ymmons Industries, Inc. rooks rive raintree, A 08 hone: (800) Fax: (800) opyright 07 ymmons Industries, Inc. symmons.com gethelp@symmons.com ZV-56 RV