Absco Regent Garden Shed Assembly Instructions Model: 30372RK

Size: px

Start display at page:

Download "Absco Regent Garden Shed Assembly Instructions Model: 30372RK"

Clarissa McDonald
5 years ago
Views:

Shed Assembly Instructons Model: 3037RK FRONT: 3.0m SIDE: 3.66m HEIGHT:.

DEEP AROUND THE PERIMETER 00mm REBATED EDGE CONCRETE SLAB THIS WILL HELP WATER EGRESS FROM THE BASE OF

For further assstance please vst our detaled nstructonal vdeo lbrary at Http://www.abscosheds.com.

1 Shed Assembly Instructons Model: 3037RK FRONT: 3.0m SIDE: 3.66m HEIGHT:.m 3760mm CONCRETE SLAB 300mm CONCRETE WHEN LAYING YOUR CONCRETE SLAB, ENSURE THERE IS A REBATED EDGE 5mm DEEP AROUND THE PERIMETER 00mm REBATED EDGE CONCRETE SLAB THIS WILL HELP WATER EGRESS FROM THE BASE OF THE SHED 75mm WIDE REBATE We thank you for choosng an Australan made shed. For further assstance please vst our detaled nstructonal vdeo lbrary at At ABSCO Industres we are always lookng to be number ONE, so please let us know what you thnk of our nstructons. Feedback makes us better. feedback@absco.com.au PAGE

GENERAL INSTRUCTIONS Absco Regent Garden Before

detal to gan a thorough understandng of assembly

Unpack the carton and carefully dentfy and check off

An uneven surface may result n msalgnment of parts.

concrete slab and anchored down approprately (refer to

Anchor sets are not suppled as standard tems wth ths

Normal: 4mm & 0mm Masonry: 0mm Some parts may have

It s advsable to wear gloves when handlng these tems

2 GENERAL INSTRUCTIONS Absco Regent Garden Before commencng any assembly, read through these nstructons n detal to gan a thorough understandng of assembly methods and assocated detals. Unpack the carton and carefully dentfy and check off all the parts aganst the parts descrbed and llustrated on pages three and four. SITE PREPARATION The ste for the shed must be level. An uneven surface may result n msalgnment of parts. It s recommended that the shed be set on a 00mm concrete slab and anchored down approprately (refer to last page for detals). Anchor sets are not suppled as standard tems wth ths product as some customers wsh to use ther own anchorng systems. TOOLS REQUIRED OPTIONAL Normal: 3mm A NOTE ON SAFETY Normal: 4mm & 0mm Masonry: 0mm Some parts may have sharp edges. It s advsable to wear gloves when handlng these tems and safety glasses f drllng holes. Sensble shoes are hghly recommended. Do not erect your shed n wndy condtons, ensure that the shed s securely anchored to a sold foundaton mmedately after constructon s completed. It s hghly recommended to erect the shed wth two or more people. PAGE

3 COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS QTY COMPONENT DESCRIPTION PART No. CHECK QTY COMPONENT DESCRIPTION PART No. CHECK STEEL SHEET 785mm X 773mm 30A 4 STEEL SHEET 785mm X 73mm 3A 8 STEEL SHEET 785mm X 773mm 3A STEEL SHEET 75mm X 773mm A STEEL SHEET 546mm X 773mm 44L STEEL SHEET 75mm X 773mm B STEEL SHEET 44R 546mm X 773mm GABLE R/H L=475mm 6R 6 STEEL SHEET 546mm X 773mm 45A GABLE L/H L=475mm 6L STEEL SHEET 785mm X 7mm 34A BRACE L: 393mm 3A L = 568mm 79A 79A L = 75mm 58B 58B 58A WITH HINGES L = 75mm 58A 4 L = 773mm 58C 58C 4 LIP TRIM L= 546mm ALL SHEETS HAVE PART NO.S LOCATED ON LOWER RIGHT OR UPPER LEFT CORNER OF COLORED SIDE AS SHOWN 87B Part No. Here 87B PAGE 3

4 COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS QTY COMPONENT DESCRIPTION PART No. CHECK QTY COMPONENT DESCRIPTION PART No. CHECK 4 Part No. Here JAMB L= 0mm 9A Part No. Here 89A JAMB L= 785mm Part No. Here JAMB L= 75mm 89C CONTENTS OF FITTINGS PACKET Part No. Here JAMB L= 568mm 90A 0 SELF TAPPING SCREWS 3 DOOR PADBOLT A 8 4mm NUT & BOLT SET SECURE TWO PADBOLTS TO DOOR SHEET DOOR PADBOLT HASP 4mm CSK SCREW & NUT SECURE HINGES TO DOOR DOOR STRAP L: 6.5" A ASSEMBLY INSTRUCTIONS 8 SELF DRILLING HEX HEAD TEK SCREWS (NO HOLE REQUIRED) CAP GABLE L: 70mm 4A HEX TEK SCREW DRIVER BIT 3mm DRILL BIT PAGE 4

5 COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS QTY COMPONENT DESCRIPTION PART No. CHECK QTY COMPONENT DESCRIPTION PART No. CHECK CSJ ZARSP CSJ JOINER L= 00mm THESE COMPONENTS ARE TO BE JOINED RIDGE BEAM JOINER L: 450mm TO THESE COMPONENTS L = 496.5mm 77AL JOIN>> 77AL L = 496.5mm 77AR JOIN>> 77AR L = 496.5mm 55CL JOIN>> 55CL L = 496.5mm 55CR JOIN>> 55CR L = 496.5mm 77BL JOIN>> 77BL L = 496.5mm 77BR JOIN>> 77BR L = 496.5mm 8BL JOIN>> 8BL L = 496.5mm 8BR JOIN>> 8BR L = 866.5mm 8LL JOIN>> 8LL L = 866.5mm 8LR JOIN>> 8LR L = 866.5mm 6BL JOIN>> 6BL L = 866.5mm 6BR JOIN>> 6BR 8KL L = 89.5mm 8KL JOIN>> 6AL L = 89.5mm 6AL JOIN>> L = 89.5mm L = 89.5mm 8KR JOIN>> 6AR JOIN>> 8KR 6AR RIDGE BEAM 97DL RIDGE BEAM 97DR L = 866.5mm L = 866.5mm PAGE 5

6 INSTRUCTIONS FOR JOINING SPLICED S NOTE: THE TEXT MARKED ON ALL PARTS MUST BE SHOWN ON THE SAME SIDE AS EACH OTHER. = = = = CSJ JOIN>> <<JOIN JOIN>> = = J JOIN>> SJ STEP. Poston the channels and the CSJ joner channel so the center of the CSJ s n lne wth the end of each channel to be joned together. STEP. Jon the frst channel to the CSJ by nsertng the center of the CSJ (on an angle) to the end of the channel where the JOIN>> text s marked. Push down one sde of the CSJ untl you hear a 'clck'. = = JOIN>> <<JOIN JOIN>> <<JOIN DRILL 4 x 3mm ( PER A SIDE) HOLES TO SECURE SECTIONS TOGETHER. (THESE SCREWS MAY HAVE TO BE TEMPORARILY REMOVED AND REPLACED DURING LATER ASSEMBLY) = = STEP 3. Jon the second channel to the CSJ by postonng the <<JOIN end of the channel at the center of the CSJ (on an angle). Push the CSJ nto the channel untl you here a 'clck'. FINISHED The joned channels should now look lke the pcture above wth the CSJ postoned equally nsde of the joned channels. PUSH QTY = 0pcs. CSJ PUSH CSJ CSJ CSJ HIGH-SIDE CSJ LOW-SIDE 0mm 5mm CSJ PAGE 6

7 STEP. PRE-ASSEMBLY OF SPLICED S NOTE: JOIN TOGETHER 4 X SECTIONS USING X JOINERS (PART CSJ) X 77AR X 77AL NOTE: SOME S HAVE HOLES IN THEM - YOU WILL NEED TO RE-DRILL HOLES ON ANY WHERE THE CSJ JOINING COVERS HOLES ON THE S YOU ARE CONNECTING 77AL 993mm 77AR 55CR 77BL 77BR 8BR = = = = x 77A x 77B x 55C x 8B X 77BR X 77BL X 55CR X 55CL X 8BR X 8BL X 8LR X 8LL X 6BR X 6BL X 8KR X 8KL X 6AR X 6AL 55CL 8BL 8LL 3733mm 8LR 6BL 6BR 8KL 3659mm 8KR 6AL 6AR = x 8L = x 6B = x 8K = x 6A PAGE 7

8 INSTRUCTIONS FOR JOINING SPLICED RIDGE BEAM STAGE : PUSH RIDGE BEAMS TOGETHER, MAKE SURE THERE IS A 50mm OVERLAP OF THE RIDGE CAP STAGE : INSERT RIDGE CAP JOINER INTO CONNECTED RIDGE CAPS. MAKE SURE JOINER HAS 5mm IN EACH RIDGE CAP. STAGE 3: TURN RIDGE CAP OVER AND MEASURE 50mm FROM THE END OF EACH RIDGE CAP. PLACE TEK SCREWS IN 50mm INCREMENTS FROM SAID END. REPEAT THIS PROCESS FOR THE OPPOSING HALF OF RIDGE BEAM PAGE 8

9 STEP. PRE-ASSEMBLY OF SPLICED RIDGE BEAM QTY. = TEK SCREW DRIVER BIT QTY. = 8 SELF DRILLING TEK SCREW QTY. = RIDGE BEAM 3733mm PARTS 97DL & 97DR QTY. = PUSH PUSH PART ZARSP - 450mm 6mm 97DR ZARSP 00mm 50mm 97DL 6mm (PART 97D) 3733mm OVERALL LENGTH THE TOP SECTIONS OF CAPPING WILL OVERLAP EACH OTHER AT THE JOIN BY 50mm. PAGE 9

10 Shed Model: 3037RK VIEW OF ROOF COMPONENTS 87B 6B 44R 87B 45A 45A 44L 45A 45A 45A 45A 8L 44R 87B 8L 44L 97D 4A 87B PAGE 0 NO.

11 Shed Model: 3037RK 6L 6R 30A 3A 3A 77B 3A 30A 3A 6A 3A 8K 3A 3A 6L 8B 3A 3A 8K VIEW OF WALL COMPONENTS 3A 34A 3A 3A 89A 55C 6A 3A 90A 9A 9A 79A 3A A 34A 89A 6R B 77A A PAGE

ABSCO ASSEMBLY INTRODUCTION The snaptte assembly system locks most permeter channels to all roof and wall sheets wthout the need for tools and fasteners.

end. Poston sheets on tmbers, trestles or partly over edge of concrete slab. FASTENING SYMBOLS D PUSH HIGH SIDE Jon components together by pre-drllng the holes frst.

12 ABSCO ASSEMBLY INTRODUCTION The snaptte assembly system locks most permeter channels to all roof and wall sheets wthout the need for tools and fasteners. To pre-assemble the four wall panels and two roof panels, the permeter channels are secured to the top and bottom of each panel usng the snaptte system, as detaled on the followng pages wherever you see the symbol. HIGH SIDE PUSH HIGH SIDE HIGH SIDE HIGH SIDE PUSH After jonng sheets together, poston channel over one end of the sheets, gently tappng t over the snaptte lugs, workng along the sheets to the other end. Poston sheets on tmbers, trestles or partly over edge of concrete slab. FASTENING SYMBOLS D PUSH HIGH SIDE Jon components together by pre-drllng the holes frst. Use one component as a template to mark where the holes are. Drll wth 3mm drll bt. Jon components together wth one screw at ths locaton only, as some channel sectons have extra holes that are not requred for ths model of garden shed Do not jon components together at ths locaton yet, as the screw may obstruct further assembly of other components Each permeter channel must fnsh flush wth the edges of the sheets.the snaptte system allows adjustment for ths process by smply tappng the channel along the sheets untl each end s neatly flush. If you need to remove channels from the panels, pull the channel along the panel from opposng ends. You may need someone to help wth ths. 3mm POP RIVETS 4mm NUT & BOLT SET PAGE

DIRECTION IN COMPARISON TO HORIZONTAL DOOR S B A 0mm

13 DOOR DOOR PANEL ASSEMBLY 58C 58C 58A 58B B A A 58C 58A 58C 89C ALL VERTICAL DOOR S ARE INSTALLED IN THE REVERSE DIRECTION IN COMPARISON TO HORIZONTAL DOOR S B A 0mm FLANGE 5mm FLANGE FOUR HOLE SET FOR PADBOLT CONNECTION PAGE 3

14 REAR PANEL ASSEMBLY 30A 3A 77B 30A 3A 8B 3A 3A SIDE PANEL ASSEMBLY ( Requred) 3A 3A SMALL PAN 6A 3A SMALL PAN 8K PAGE 4

15 ROOF PANEL ASSEMBLY ( Requred) 44R 45A 45A 44L 45A 87B x PRE-PUNCHED HOLES TO THIS END OF EACH SHEET WITH PART NO. 8L FITTED 6B 8L 87B PAGE 5

16 FRONT PANEL ASSEMBLY 89A 89A 34A 34A 77A 90A 79A 55C PAGE 6

17 DOOR PANEL ASSEMBLY 9A 9A B A NOTE: Nuts and bolts (suppled) may be used nstead of pop rvets (suppled) by smply enlargng the hnge hole sets n the jamb usng a 4mm drll bt NOTE: The two holes requred to connect the padbolt hasp for each door have not been pre-punched, to allow for proper algnment. poston each hasp centrally over the padbolt shaft, and drll 3mm holes and secure wth screws PAGE 7

18 PANEL CONSTRUCTION NOTE: Take care to ensure that both front and rear wall panels are not postoned upsde down. the top channel of each panel s pre-punched for attachng roof sheets, the bottom channels are not. SIDE WALL PANEL S FIT INTO THE NOTCHED FRONT AND REAR WALL PANEL S TYPE 6B THIS END 97D TYPE 8L THIS END PAGE 8

19 ROOF CONSTRUCTION 37mm OUTSIDE VIEW ROOR OVERHANGS ALL WALL PANELS BY 37mm INSIDE VIEW SECURE RIDGE BEAM TO GABLE SECTIONS WITH TWO SCREWS AT EACH END. SECURE EACH ROOF PANEL WITH ONE SCREW IN EACH CORNER ONLY AT THIS STAGE INSIDE VIEW 3A AFTER ATTACHING BOTH ROOF PANELS TO WALLS AS SHOWN ABOVE, FIT ONE REGENT BRACE TO THE RIDGE BEAM AND FRONT WALL AS SHOWN. YOU WILL HAVE TO REMOVE AND REPLACE EXISTING SCREWS AT FIXING LOCATIONS. REPEAT THIS PROCEDURE FOR THE REAR WALL REGENT BRACE PAGE 9

20 FINAL CONSTRUCTION 4A BEND THE TOP AND BOTTOM FLANGES AS SHOWN, THEN HOOK THE BOTTOM FLANGES UNDER THE TOP AND SCREW THE TOP FLANGES FOR BOTH AS SHOWN GABLE CAPS ANCHORING OF SHED LOCATION OF 6 CONCRETE ANCHORS - EACH ANCHOR CONSISTS OF ONE NUT, BOLT, DYNABOLT AND STEEL ANGLE - DRILL A 0mm HOLE INTO THE WALL SHEET BOLT & NUT STEEL ANGLE WALL SHEET SLAB - DRILL A 0mm HOLE INTO THE CONCRETE DYNABOLT PAGE 0

21 AUSTRALIA PRODUCT WARRANTY AGAINST DEFECTS Congratulatons on your purchase of an ABSCO SHED ABSCO SHEDS, ncludng garden sheds, garden beds, avares, storage unts, garages, awnngs and carports are made usng hgh qualty Australan made steel. We are pleased to advse we warrant that the steel coatng wll not rust, crack, flake peel or blster for 30 years from date of purchase, when nstalled wthn Australa. Ths warranty does not apply to surface deteroraton of panels caused by Swarf (Tny partcles of steel debrs left from cuttng, grndng or drllng operatons) that has not been removed after buldng constructon, or as a result of contact wth damp sol, chemcals, fertlsers or other corrosve substances. Ths warranty covers any Absco product used for normal domestc use and nstalled n accordance wth the nstallaton nstructons. The warranty does NOT cover Damage caused by storms, wnd, ran snow or poor foundatons. Ths warranty does NOT cover ABSCO products nstalled n severe coastal, ndustral or other hghly corrosve envronments. The warranty does not cover fasteners (screws, nuts, bolts, rvets, hasps or sldng padbolts). The warranty s lmted to replacement and delvery of components and does not nclude any labour or nstallaton costs. The benefts gven by the warranty are n addton to your other rghts and remedes under a law n relaton to the goods or servces to whch the warranty relates. The warranty apples to the excluson of all other representatons, guarantees or warrantes express or mpled, our goods come wth guarantees that cannot be excluded under the Australan consumer law and s not transferable. You are enttled to a replacement or refund for a major falure and for compensaton for any other foreseeable loss or damage. You are also enttled to have the goods repared or replaced f the goods fal to be of an acceptable qualty and the falure does not amount to a major falure. For further nformaton go to Please retan a proof of purchase (sales docket or nvoce) or regster your warranty wthn 30 days of purchase here: In the unlkely event a warranty clam s made, t must be supported by photographc evdence and detals of the defect, ncludng component part numbers, together wth proof of purchase documentaton (or on-lne regstraton of purchase) and forwarded to the address below. Upon recept of the warranty clam, the Customer Servce Manager wll contact you wthn three busness days to advse you of the assessment outcome of the clam, whch may nclude your expenses ncurred n makng the clam. THE CUSTOMER SERVICE MANAGER, ABSCO INDUSTRIES, PO BOX 9 ACACIA RIDGE QLD AUSTRALIA 40 PHONE: FAX: warranty@absco.com.au Issued 0 January 03 P a g e

22 ABSCO SHEDS - STORAGE GUIDELINES ABSCO SHEDS nclude garden sheds, garden beds, storage unts, avares, garages, awnngs and carports. ABSCO SHEDS are desgned to be weatherproof for normal weather condtons. In the event of extreme weather condtons such as heavy ran, combned wth hgh wnd gusts, the rdge cappng, sheetng jons, screw fxngs etc., may exhbt mnor deformatons whch may allow some water entry. These areas should be checked regularly to ensure that maxmum strength and protecton s mantaned. Other weather condtons such as extreme heat and extreme cold, most or dry ar can nfluence the effects of concrete floor mosture and/or condensaton on the undersde of the roof sheets. ABSCO SHEDS and storage unts are prmarly used for storage of garden equpment such as lawnmowers, wheelbarrows, garden tools etc. Storage tems that mght be adversely affected by any of the above condtons may requre addtonal protecton such as beng sealed or covered by plastc sheets and/or stacked above the concrete floor on tmber slats. Waterproof sealants may be used to offer further protecton where requred around jons and screw fxngs, as can rubber door seals and other products whch are avalable from most hardware outlets. Placement of waterproof sealants (slcone) between the base of the shed and concrete slab s not recommended, as ths process can have a reverse effect, preventng excess water from escapng, resultng wth water accumulatng and beng trapped nsde the shed. Absco accepts no responsblty for water entry, floor mosture, condensaton or the condton of the Contents nsde your Absco steel buldng arsng from any of the pre-mentoned weather condtons. P a g e

Absco Premier Garden Shed Assembly Instructions Model: 30302GK

Absco Premier Garden Shed Assembly Instructions Model: 30302GK Absco Premer Garden Shed Assembly Instructons FRONT: 3.0m SIDE: 3.0m HEIGHT:.m 300mm CONCRETE SLAB 300mm WHEN LAYING YOUR CONCRETE SLAB, CHAMFER THE 50mm EDGES DOWNWARDS BY 0mm. 50mm 0mm 50mm THIS WILL