Paris Crib and Changer Assembly Instruction

Transcription

1 Paris Cri and Changer Assemly Instrution Important Inormation: Read all instrutions BEFORE assemling ri. KEEP INSTRUTIONS FOR FUTURE USE. Made in China

2 Cri Warnings: WARNING: SORELLE *Inants an suoate on sot edding. Never add a pillow or omorter. Never plae additional padding under an inant. *Failure to ollow these warnings and the assemly instrutions ould result in serious injury or death. DO NOT use this ri i you annot exatly ollow the aompanying instrutions. *To redue the risk o SIDS, pediatriians reommend healthy inants e plaed on their aks to sleep, unless otherwise advised y your physiian. *Strangulation Hazard: STRINGS CAN CAUSE STRANGULATION! Do not plae items with a string around a hild's nek, suh as hood strings or paiier ords. Do not suspend strings over a ri or attah strings to toys. *Strangulation Hazard: To help prevent strangulation tighten all asteners. A hild an trap parts o the ody or lothing on loose asteners. *Strangulation Hazard: Do not plae ri near window or patio door where ords rom linds or drapes may strangle a hild. *Fall Hazard: When hild is ale to pull to a standing position, set mattress to lowest position and remove umper pads, large toys and other ojets that ould serve as steps or liming out. This ri has an adjustale mattress support. For the onveniene o the parent when the ay is very small, the mattress support may e used in the highest position. *Fall Hazard: Stop using ri when hild egins to lim out or reahes a height o 35in. (89m), whihever ours irst. The hild should e plaed in a youth or regular ed. *Chek this produt or damaged hardware, loose joints, loose olts or other asteners, missing parts, or sharp edges eore and ater assemly and requently during use. Seurely tighten loose olts and other asteners. Do not use ri i any parts are missing, damaged or roken.contat C&T International In./Sorelle or replaement parts and instrutional literature i needed. Do not sustitute parts. *Follow warnings on all produts in a ri. *I reinishing, use a non-toxi inish speiied or hildren's produts. *Never use plasti shipping ags or other plasti ilm as mattress overs eause they an ause suoation. *Inants an suoate in gaps etween ri sides and a mattress that is too small. *Ensure a sae environment or the hild y heking regularly, eore plaing the hild in the ri, that every omponent is properly and seurely in plae. *To avoid head injury, do not allow any hild to play underneath the ri. *Never add an aessory suh as a assinet or hanging tale that extends over the sleeping area. CAUTION : ANY MATTRESS USED IN THIS CRIB SHALL BE AT LEAST 271/4 (69CM) x 515/8 (131 CM) WITH A THICKNESS NOT EXCEEDING 6 (15CM). Page 1

3 Changing Tale Warnings: WARNING FALL HAZARD - to prevent death or serious injury, always keep hild within arm s reah. Read all instrutions eore use o the hanging tale. KEEP THESE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE USE. Inspet the hanging tale periodially. Do not use the hanging tale i it is damaged or roken. Contat C&T International In. with any questions. Tighten all loose srews and olts eore eah use. The maximum reommended weight o the hild is 30ls or the hanging tale. Use only the pad provided y C&T International In. or Manuaturer s Always seure the pad to the hanging surae y inserting the strap through the hole in the middle o the pad. See Instrutions. NEVER use ri without Changing Tale attahed Toddler Bed Warnings: WARNING INFANTS HAVE DIED IN TODDLER BEDS FROM ENTRAPMENT. Openings in and etween ed parts an entrap head and nek o a small hild. NEVER use ed with hildren younger than 15 months. ALWAYS ollow assemly instrutions. The maximum user weight is 50ls (22.7kg) WARNING STRANGULATION HAZARD NEVER plae ed near windows where ords rom linds or drapes may strangle a hild. NEVER suspend strings over a ed. NEVER plae items with a string, ord, or rion, suh as hood strings or paiier ords, around a hild's nek. These items may ath on ed parts. CAUTION ENTRAPMENT HAZARD To avoid dangerous gaps, any mattress used in this ed shall e a ull-size ri mattress at least 51 5/8 in (1310mm) in length, 27 1/4 in (690mm) in width and 4 in (100mm) in thikness. The mattress thikness must not exeed 6 in (150mm). NOTE: TODDLER RAIL MODEL # 129 IS SOLD SPEARATELY. NOTE: ADULT RAIL MODEL # 223 IS SOLD SPEARATELY. Page 2

4 Parts list (A): Bak Side Rail (x1) (B): Front Side Rail (x1) (C): Let Side Rail (x1) (D): Middle Panel (x1) (E): Right Panel (x1) (F): Mattress Support(x1) (G): Bak Let Leg (x1) (H): Front Let Leg (x1) (K1): Changer Front Contoured Top (x1) (I): Front & Bak Contoured Top (x2) (J): Deorative Support Bar Bolt Ends (X1) (K): Small Front Support Bar (x1) Important: In order to properly assemle the ri, arry out the operations in order speiied. Failure to assemle the ri in the manner reommended order an make the ri hazardous. Page 3

5 Parts list (L): Bak Middle Bar (x1) (Side Groove) (M): Front and Bak Bottom Support Bar (x2) (Side Groove) (N): Front Middle Bar (x1) (O1): Top Shel (x1) (O2): Bottom Shel (x1) (P): Bak Middle Shel (x1) (Q) Change Pad (x1) (R): Drawer Let (x1) (S) Drawer Right (x1) (T) Drawer Bak (x1) (U): Drawer Bottom (x1) (V) Drawer Front (x1) (Y): Bak Middle Leg (x1) (Z): Bak Right Leg (x1) Important: In order to properly assemle the ri, arry out the operations in order speiied. Failure to assemle the ri in the manner reommended order an make the ri hazardous. Page 4

6 Assemly Hardware Set a. General Allen head olt M6 X 70mm ( 4 ps) j. Kno Srew (1 p). General Allen head olt M6 X 55mm ( 10 ps) k. Door Kno (1 p). General Allen head olt M6 X 35mm ( 25 ps) i. General Allen head olt M6 X 40mm ( 2 ps) d. General Allen head olt M6 X 16mm ( 4 ps) m. Allen Wrenh ( 1PCS ) e. Srews 32mm ( 8PCS ). Wooden dowel ( 8PCS) Important: In order to properly assemle the ri, arry out the operations in order speiied. Failure to assemle the ri in the manner reommended order an make the ri hazardous. Page 5

7 STEP 1 LEFT PANEL ASSEMBLY SORELLE A.. Install Srews (e) into Drawer Sides (S &R) and align with pilot holes loated in the Drawer Bak (T).Tighten using Phillips srew driver(not inluded). B. Slide Drawer Bottom (U) into Grooves loated in Drawer sides (S &R) as well as Drawer Bak (T). See Figure. 1 C. Install Srews (e) into Drawer Sides (S &R) and align with pilot holes loated in the mounting loks o Drawer Front (V).Tighten using Phillips srew driver(not inluded). D. Using Drawer Kno Srew (j), install one Kno (k) on drawer. Drawer Bak(T) e Drawer Right(S) e Drawer Front(V) Drawer Let(R) 4. Using Drawer Kno Srew (j), install one (1) Kno (k) on Drawer. e Drawer Bottom (U) e (k) (j) STEP 2 LEFT PANEL ASSEMBLY A. Using our 4 x olt (), assemle Bak Let Leg (G) and Front Let Leg (H) to Let Side Rail (C). Make sure all mattress support holes are aing in. Figure 2. Bak Let Leg(G) 4x m Let Side Rail(C) Front Let Leg(H) 2 page 6

8 STEP 3 MIDDLE & RIGHT PANEL ASSEMBLY A. Using three 3 x olt (), assemle Bak Middle Leg (Y) to Middle Panel (D). Figure 3A. B. Using three 3 x olt (), assemle Bak Right Leg (Z) to Right Panel (E). Figure 3B. Bak Middle Leg (Y) Bak Right Leg (Z) Middle Panel(D) Right Panel(E) Figure 3A: Figure 3B: STEP 4 CHANGER ASSEMBLY (PART 1) A. Using two 2 x olt (), assemle Small Front Support Bar (K) to the Middle Panel (D). Figure 4A. Insert one 1x wooden dowel () on either end o Front Middle Bar (N). Connet (N) to Middle Panel (D) using one 1 x olt (). Figure 4A. Using one 1 x olt (). assemle the Front Bottom Support Bar (M) groove aing inward. Figure 4A. B. Using two 2 x olt () and one 1 x wooden dowel (), assemle the Deorative Support Bar (J) to Bak Middle Leg (Y). Figure 4B. Using one 1 x olt () assemle the Bak Middle Bar (L) groove aing upward. Figure 4B. Using one 1 x olt (), assemle the Bak Bottom Support Bar (M) groove aing inward. Figure 4B. Middle Panel(D) Small Front Support Bar (K) Bak Middle Leg (Y) Front Middle Bar (N) Deorative Support Bar Bolt Ends (J) Middle Panel(D) Figure 4A : Front and Bak Bottom Support Bar (M) Bak Middle Bar (L) Figure 4B : page 7

9 STEP 5 CHANGER ASSEMBLY (PART 2) A. Slide Top Shel (O1) and Bottom Shel (O2) veneered side up horizontally into the grooves.1 B. Slide Bak Middle Shel (P) veneered side aing outwards vertially into the grooves. Figure 5. Middle Panel (D) Top Shel (O1) Bak Middle Shel (P) Bottom Shel (O2) Figure 5 : STEP 6 CHANGER ASSEMBLY (PART 3) A Insert one 1 x wooden dowel () to the top hole o the the Deorative Support Bar (J). Figure 6A. B Insert eight 8 x olt () into remaining exposed holes and asten to onnet Right Panel (E). Figure 6B. Figure 6A: Figure 6B: Right Panel (E) page 8

10 STEP 7 ASSEMBLY OF BACK SIDE RAIL A. Attah the Bak Contoured Top (I) to the Bak Side Rail (A). Seure with two 2 x olt (a) rom underneath. Figure 7A. B. Insert on 1 x wooden dowel () on either end o the Bak Side Rail assemly (I) +(A). Figure 7A. C. Seure the Bak Side Rail assemly (I) + (A) to the hanger unit y using two 2 x olt (). Figure 7B. D. Attah the Let Side Rial (C) using two 2 x olt (). Figure 7B. Bak Contoured Top (I) a a Bak Side Rail (A) Figure 7A : Figure 7B : Figure 7C : Let Side Rail (C) STEP 8 ASSEMBLY OF MATTRESS SUPPORT A. Swing out the our arms and attah the Mattress Support (F) using our 4 x olt (d). Reommended mattress position: Top position or neworn. Middle position as your hild starts to roll over. Lowest position when your hild an sit or pull up on his/her knees. D F d m Mattress Support(F) Figure 8 : page 9

11 STEP 9 ASSEMBLY OF FRONT SIDE RAIL A. Attah the Front Contoured Top (I) to the Front Side Rail (B). Seure with two 2 x olt (i) rom underneath. Figure 9A. B. Insert one 1 x wooden dowel () on either end o the Front Side Rail assemly (I) + (B). Figure 9A. C. Seure the Front Rail Assemly (I) + (B) to the ri with our 4 x olt (). igure 9B. i Front Contoured Top(I) i Front Side Rail(B) Figure 9A : Figure 9B : STEP 10 ASSEMBLY OF CHANGER FRONT CONTOURED TOP Insert groove on Changer Front Contoured Top (K1) to the top o Small Front support Bar (K) and seure with two 2 x olt (a) rom underneath. Figure 10. K1 a Figure 10 : page 10

12 STEP 11 INSERT DRAWER SORELLE A. Insert drawer.figure 11. Figure 11 : Changing Pad Assemly Important : I hanging pad and saety elt are assemled, make sure warnings are aing up and visile. I not, reassemle y ollowing the steps elow. 1. Loate saety elt olted to dresser top. Insert saety elt through slit in hanging pad rom ak o pad. Figure Pull through ront o pad ompletely. Make sure pad is aing up and warnings are always visile. Figure Make sure that saety elt is astened around hild, and adjusted so saety elt is snug around hild s mid-setion. Make sure ukle is seurely lathed. Figure CLICK! page 11