Sole Fitness E95 Elliptical Trainer TurnKey Delivery and Setup Training
|
|
- Andrea Freeman
- 6 years ago
- Views:
Transcription
1 Sole Fitness E95 Elliptical Trainer TurnKey Delivery and Setup Training Delivery Requirements Ground delivery Inside delivery to customer-specified location Unpack and assemble machine, and remove packing materials Tools Required Liftgate Two-wheel dolly Cutters to cut plastic banding 1. Unload the carton from the trailer and take it to the customer-specified location using a two-wheeled dolly. When moving the carton, be sure to use safe lifting procedures. Be sure to bend at the knees and keep your back straight. Note: Some deliveries will require setup in an upstairs room or other location with limited access. When this is the case, it is recommended that you unpack the parts outside and carry them individually to the customer-specified location. 2. Unpack the contents of the cartons and remove all packing materials. Cut along the bottom edge of the carton. Remove all packing material. Locate the hardware packet. 3. Review the assembly instructions. Inside the carton, you will find the Owner s Manual. It will be necessary for you to follow the manufacturer s assembly instructions to be able to complete the assembly of the Sole Fitness E95 Elliptical Trainer. Do not attempt to assemble this machine without the Owner s Manual. 4. Install the incline rail assembly into the U-channel bracket of the main frame. Place the incline rail assembly into the U-channel on the main frame. Install four bolts, split washers, and star washers into the top of rail assembly. Install two bolts and two nylon nuts into the sides of the U-channel. Connect the three incline motor power lines and the 3-pin position sensor connector on the main frame to the corresponding ones on the incline rail assembly. (This is shown in Step 1.1 and 1.2 on page 8 of the Owners Manual) Be careful not to pinch or cut the wires. 5. Attach the console mast and console mast cover to the main frame. Slide console mast cover onto the mast. Pull the cable out of the top of the main frame and unravel and straighten out. Feed the cable into the bottom of the console mast and out the top. Install the mast into the receiving bracket on the main frame. Install one long hex bolt and split washer into the side of the bracket and mast. Install two short hex head bolts and curved washers into the front of the console mast. (This is shown in Step 1.2 and 1.3on page 8 in the Owner s Manual.) 6. Attach the console to the console mounting plate. Place the console next to the console mast plate, and then plug all of the connectors into the back of the console. Secure the console to the console mounting plate with four Phillips head screws. Be careful not to pinch or cut the wires. (This is shown in Step 1.4 on page 8 in the Owner s Manual.)
2 7. Attach the left and right handle bars. Remove foam pads from the handle bar axle but leave the rubber rings. Tuck the wires into the console mast and cover with the rubber grommets. Place a wave washer on each handle bar axle. Slide the handle bars on to the appropriate side of the axle. Attach both handle bars using two hex head bolts and flat washers. Connect the wires on the handle bars to the wires on the console mast. (This is shown in Step 2.1 through 2.4 on page 10 of the Owner s Manual.) Be careful not to pinch or cut the wires. 8. Install the front and rear handle bar covers. Place the front and rear handle bar covers over the handle bar and axle, and attach using four sheet metal screws per side. (This is shown in Step 2.4 on page 10 of the Owner s Manual.) 10. Install the inner connecting arm covers. Place the covers over the connecting arms and secure using two Phillips head screws and two sheet metal screws. (See Step 4.1 on page 12.) 13. Install the two stabilizer covers. Place the covers on the middle stabilizer bar, and attach with one Phillips head screw per side. (See Step 4.3 on page 12.) 11. Install the outer connecting arm covers. Place the covers over the inner covers and secure using two Phillips head screws and two sheet metal screws. (See Step 4.1 on page 12) 14. Install front stabilizer cover. Place the front stabilizer cover on the front stabilizer and attach using two Phillips head screws. (See Step 4.4 on page 12.) 15. Install the rear incline bar cover (cont.) Place the rear incline bar over the rear incline bar and attach it to the rail base using four Phillips head screws. 9. Connect the handle bars to the connecting arms. Align the hole in the rod end of the connecting arms with the brackets on the handle bar, and attach using a hex head bolt, flat washer and nylon nut. (This is show in Step 3 on page 11 of the Owner s Manual.) 16. Install the rear stabilizer cover. 12. Install sliding wheel covers. Place the sliding wheel covers over the wheels on the connecting arms and secure using two Phillips head screws per side. (See Step 4.2 on page 12) 15. Install the rear incline bar cover. Attach the two incline cover brackets to the incline rail assembly using four Phillips head screws. (See Step 4.5 on page 12.) Install the rear stabilizer cover on the rear stabilizer using four Phillips head screws. (This is shown in Step 4.5 on page 12 of the Owner s Manual.) (This is show in Step 4.6 on page 12 of the Owner s Manual.) 17. Install the incline rail front cover. 18. Plug the power cord into the main 19. Remove all packing materials. Place the incline frame of the elliptical trainer, and then rail front cover plug the power cord into the wall outlet. over the middle stabilizer tube, and attach with four Phillips screws. (See Step 4.7 on page 12.)
3
4
5
6
7
8
9
10
11
INSTALLATION INSTRUCTIONS
TreadClimber INSTALLATION INSTRUCTIONS STAR TRAC FITNESS 1 of 14 635-4175 Rev: B NOTICE Installation of this product requires that 2 or more people are available to safely perform certain steps outlined
More informationPERSONAL RECORD KEEPING
2 P R O 3 7 0 A s s e m b l y i n s t r u c t i o n s PERSONAL RECORD KEEPING Tip: Record the serial numbers of your Octane Fitness elliptical in the spaces below. This will make it easier for you to obtain
More informationStar Trac Turbo Trainer Assembly & Setup
Star Trac Turbo Trainer Use the following procedures to unpack and assemble your Turbo Trainer manufactured by Star Trac. UNPACKING AND PARTS LIST Position the shipping carton so the Heavy End logo is
More informationArc Trainer Main Frame Assembly
Arc Trainer Main Frame Assembly Kit No. 610AK019-4 Kit No. 630AK019-4 NOTE: This instruction sheet describes how to replace the main frame assembly in the Arc Trainer 610A. Tools Required 3/16 Allen wrench
More informationOWNERS MANUAL MODEL F660 HIP SLED
OWNERS MANUAL MODEL F HIP SLED QUESTION? As a quality home gym supplier we are committed to your complete satisfaction. If you have questions, or find missing or damaged parts, we will guarantee your complete
More informationCable Tray Kit: - Cable Tray - Cable Tray Cover - Power Block Support (x2) Top Support Kit: (x2) - 2 Top Supports. Quantities are per bench
Parts Included (per back to back bench) Column Kit: (x2) - 1 LH & 1 RH Column - Control Box - Hand Switch Cable Tray Kit: - Cable Tray - Cable Tray Cover - Power Block Support (x2) Depth Support Kit: -
More informationPERSONAL RECORD KEEPING
Q47e/Q47ce 2 Q 4 7 e / Q 4 7 c e A s s e m b l y i n s t r u c t i o n s PERSONAL RECORD KEEPING IMPORTANT: Record the serial numbers of your Octane Fitness elliptical in the spaces below. This will make
More informationTROLLA LEAVY 97 CM Lawn sweeper
TROLLA LEAVY 97 CM Lawn sweeper Artikel nr.: 1008 EN Operating manual 014/1 Dear Customer, Congratulations on your new Trolla product. We hope you will enjoy it. Checkout with your new Trolla product may
More informationTable of Contents. Product Safety Part Drawing & Contents Hardware & Tools Assembly Adjustment
Owner s Manual A Table of Contents Product Safety.. 01. Part Drawing & Contents..... 02. Hardware & Tools.. 03. Assembly... 04. Adjustment... 10. Trouble Shooting & Maintenance.. 11. Computer... A. Warm
More informationLifeGear G1 /HOME GYM ITEM NO.: 63100
LifeGear G1 /HOME GYM ITEM NO.: 63100 OWNER S MANUAL IMPORTANT: Read all instructions carefully before using this product. Retain this owner s manual for future reference. The specifications of this product
More informationASSEMBLY INSTRUCTIONS MANUAL
PAGE 1 OF 9 RECOMMENDED TOOLS FOR ASSEMBLY: ALLEN WRENCH (INCLUDED) BOX WRENCH (INCLUDED) PHILLIPS SCREW DRIVER (NOT INCLUDED) PARTS IN CARTON: ALLEN WRENCH SCREWS (20 EACH) ROUND HEAD SCREWS (8 EACH)
More informationMAG-CONV Basic, 48, 48R & Midline Front Mount
Parts Required: Tools Used: Mag Wheels Brakes Brake Rods Mounting Bracket Anti Tippers 7/16" Wrench Screw Driver Rubber Mallet 5/8 Wrench 5mm Allen Wrench Step Execution Figures 1 Remove front 5" total
More informationPERSONAL RECORD KEEPING
PRO3700 2 P R O 3 7 0 0 A s s e m b l y i n s t r u c t i o n s PERSONAL RECORD KEEPING Tip: Record the serial numbers of your Octane Fitness elliptical in the spaces below. This will make it easier for
More informationFREE CLIMBER 4400 ASSEMBLY INSTRUCTIONS 27694B
FREE CLIMBER 4400 ASSEMBLY INSTRUCTIONS 27694B 1 TOOLS REQUIRED: CLAW HAMMER KNIFE 1/2 WRENCH OR SOCKET 1. USE KNIFE TO REMOVE ALL PLASTIC STRAPS FROM AROUND PALLET AND CARTON. STRAP 2. USE CLAW HAMMER
More informationFor additional assistance call
The following pages will help guide you through the process of assembling your new 48 custom prize wheel. Choose an assembly area with plenty of room to lay your pieces on the floor and also a bench or
More informationProgeny Integrated Mobile Unit Unpacking/Assembly Guide
Summary: The following instruction will guide you through the unpacking and installation of the Progeny Mobile Unit. Any question or concerns or suggestions should be directed to Progeny Technical Support
More informationRYOBI. 10 in. (254 mm) TABLE SAW MODEL NO. BTS15 REPAIR SHEET
RYOBI 0 in. ( mm) TABLE SAW MODEL NO. BTS REPAIR SHEET FIGURE A 0 0 0 0 The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding
More informationFOR MODEL: Andes 208. Rev /28/06 3:31:08 PM
FOR MODEL: Andes 208 Rev. 1.0 071607 8/28/06 3:31:08 PM ASSEMBLY CONSOLE UPPER HANDLEBAR IMPORTANT: READ THESE SAFETY INSTRUCTIONS BEFORE USE! W A RNING There are several areas during the assembly process
More informationEPPA2-KIT DUAL MONITOR ARM CONVERSION
EPPA2-KIT DUAL MONITOR ARM CONVERSION EPPA2-KIT Rev A 10/17 Model EPPA2-KIT-XXX ASSEMBLY AND ADJUSTMENT EPPA2-KIT PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and adjustment
More informationLegacy Woodworking Machinery a division of Phantom Engineering. The Legacy CNC. Assembly Manual
Legacy Woodworking Machinery a division of Phantom Engineering The Legacy CNC Assembly Manual New Orientation of the Legacy Step one: Re-orientation of the machine Remove the X-axis screw and supports.
More informationPARTS LIST GALAXY DS FLOOR MACHINE
PARTS LIST GALAXY DS FLOOR MACHINE ITEM PART NO. DESCRIPTION QTY 101 0393051 SAFETY DECAL 1 102 0393691 IDENTIFIER DECAL - GALAXY 1 103 0393351 SWITCH BOX COVER 1 104 0393531 DECAL 1 105 0393441 HANDLE
More informationBuild the. Steam Locomotive. Pack 05
Build the Steam Locomotive Pack 05 Build the Steam Locomotive Contents Step by step Stage 29: The leading truck 3 Stage 30: The leading truck 4 Stage 31: The headlamp Stage 32: The smokebox door lock Stage
More informationElliptical Unpacking and Installation Instructions
Elliptical Unpacking and Installation Instructions Use these instructions for the following Ellipticals: ClubStride 5100-LE Receiving When the carrier delivers your order, verify that the number of items
More informationPARTS LIST GALAXY FLOOR MACHINE
PARTS LIST GALAXY FLOOR MACHINE ITEM PART NO. DESCRIPTION QTY 101 0393051 SAFETY DECAL 1 102 0393691 IDENTIFIER DECAL - GALAXY 1 103 0393351 SWITCH BOX COVER 1 104 0393531 DECAL 1 105 0393441 HANDLE GRIP
More informationBend-Tech Dragon Assembly Manual
p.1 Bend-Tech Dragon Assembly Manual IMPORTANT: Please read before unpacking. Place shipping container in a wide open area where you will have room to work and assemble this product. Shipping The Dragon
More informationOwner s Manual #TSGUARD
Owner s Manual #TSGUARD PSI Table Saw Dust Collection Guard The ideal solution for table saw dust control. Version 3, 02/04 2004 PSI Woodworking Products 9900 Global Rd., Philadelphia, PA 19115 WARRANTY
More informationRC4WD Diablo V2 Instruction Manual
Version 1.1 RC4WD Diablo V2 Instruction Manual Thank you for your purchase. Welcome to the RC4WD family. This kit is a combination of many specially engineered and manufactured parts. Enjoy your build.
More informationUser Instructions Multiline Otter Scoreboard Caddy Assembly
List of parts: User Instructions Multiline Otter Scoreboard Caddy Assembly Single Caddy Double Caddy 1 1 Base assembly with attached wheels 2 4 1 1 2 4 4 8 10 20 12 Uprights (60 or 74 aluminum extrusion)
More informationThis instruction manual is an in-depth look and explanation of how to assemble and install the Murphy Bed properly and efficiently.
This instruction manual is an in-depth look and explanation of how to assemble and install the Murphy Bed properly and efficiently. Don t be put off by the size of the instruction manual as the large diagrams
More informationABM International, Inc. Navigator Assembly Manual
ABM International, Inc. 1 1.0: Parts List Tablet (Qty. 1) Tablet mount (Qty. 1) NOTE: Mount may appear and operate different then image below Control Box (Qty. 1) Motor Power Supply (Qty. 1) 2 X-axis motor
More informationINSTALLATION GUIDE TOYOTA 4 RUNNER (2013+) REAR BUMPER
INSTALLATION GUIDE TOYOTA 4 RUNNER (2013+) REAR BUMPER CONTENTS CONTENTS Rear Bumper (base or dual arm) Installation...................................... 2 Dual Swing Installation..........................................................
More informationINSTALLATION GUIDE FTX FLOOR Ford Transit ( 148" Extended Wheelbase )
INSTALLATION GUIDE 6540-FTX FLOOR Ford Transit ( 148" Extended Wheelbase ) QUICK START GUIDE Phase 1 - Assembly q 1.1 Setup... 3-4 Phase 2 - Installation q 2.1 Install Preparation... q 2.2 Floor Installation...
More informationEmagiKit. Privacy Pod Plus. Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY
EmagiKit Privacy Pod Plus Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY DIMENSIONS AND COMPONENTS 47 47 Ceiling Unit 2-B 2-L 2-R Glass Door Corner Trim Door Handle 90 Adjustable Height Work Surface 1-B
More informationHOME GYM Owner s Manual
HOME GYM Owner s Manual Content Content-------------------------------------------------------------1 Safety precautions----------------------------------------------------2 Assembly instruction-------------------------------------------------3-12
More informationTable of Contents. Product Spec cations
Table of Contents Model Specification... 2 Important Safety Instructions... 3 Safety Warning Labels... 5 Before You Start... 6 Assembly... 7 Contacts... 14 Product Spec cations Model Dimensions: 27 W x
More informationASSEMBLY AND ADJUSTMENT
EPPA MONITOR ARM EPPA Rev A 10/17 Model EPPA-XXX ASSEMBLY AND ADJUSTMENT EPPA MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and adjustment procedures. Check
More informationOBE165AF Elliptical Cross Trainer
OBE165AF Elliptical Cross Trainer TABLE OF CONTENTS PRODUCT SAFETY.. 01. PART DRAWING & CONTENTS..... 02. HARDWARE & TOOLS.. 04. ASSEMBLY.. 05. FOLDING.. 11. ADJUSTMENT.. 12. TROUBLE SHOOTING & MAINTENANCE
More informationSECTION 9: PARTS. Table Breakdown REF PART # DESCRIPTION REF PART # DESCRIPTION
SECTION 9: PARTS Table Breakdown 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 23 25 17 26 27 8 1 P0675001 CAP SCREW M8-1.25 X 30 15 P0675015 SUPPORT BLOCK 2 P0675002 TABLE SUPPORT BLOCK
More informationM2 Assembly. M2 Sub-Assemblies mm Belt Sub-Assembly mm Belt Sub-Assembly Spider Sub-Assembly... 4
M2 Assembly Table of Contents M2 Sub-Assemblies... 3 630mm Belt Sub-Assembly... 3 702mm Belt Sub-Assembly... 3 Spider Sub-Assembly... 4 Idler Bolt Sub-Assembly... 8 Y Motor Sub-Assembly... 9 X Motor Sub-Assembly...
More informationCloset Carousel Installation Instructions. Models TKA 5 Through TKA 14 Equipped with Footswitch Controls
Tools Required: Phillips Screwdriver (#2) Adjustable Wrench Level Tape Measure Utility Knife Electric Drill Drill Bits for Anchors Ladder (4 foot) Models TKA 5 Through TKA 14 Equipped with Footswitch Controls
More informationRugged Ridge 2 Receiver Hitch Kit (J21068)
Rugged Ridge 2 Receiver Hitch Kit (J21068) Installation Time: 1-2 Hours Tools Required: ¾ Open End Wrench 18 mm Socket ¼ drive Pliers/Needle nose pliers/channel locks, etc. Torque wrench Phillips head
More informationPARTS LIST GALAXY DS FLOOR MACHINE
PARTS LIST GALAXY DS FLOOR MACHINE HANDLE TUBE ASSEMBLY ITEM PART NO. DESCRIPTION QTY 101 0393051 SAFETY DECAL 1 102 0393691 IDENTIFIER DECAL GALAXY 1 103 0393351 SWITCH BOX COVER 1 104 0393531 DECAL 1
More informationBX2173 Installation Instructions Ford Focus (including the 2.3L engine) 2003 Ford Focus SVT
BX2173 Installation Instructions 2000-04 Ford Focus (including the 2.3L engine) 2003 Ford Focus SVT Serial No. The front fascia, coolant line bracket and anti-pollution devices are removed for baseplate
More informationPlease read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment.
2005-08 Pontiac G6 GT Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed
More information40670 Transit Connect/NV200/City Express/ProMaster City Partition
40670 Transit Connect/NV200/City Express/ProMaster City Partition Top Panel (1) Bottom Panel (1) Transit Connect (2014) Top Angle (1) TC Top MNT BRKT (2) TC Bottom MNT PLT (2) NV200/City Express Top Mount
More informationRBP-1215B-RX DODGE RAM QUAD CAB RX3
RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side
More informationThe Bowflex Revolution XP Home Gym Assembly Instructions. P/N: Rev ( /0 )
P/N: 001-7057 Rev ( /0 ) The Bowflex Revolution XP Home Gym Assembly Instructions 2 Table of Contents Before You Start... 2 Tools You Will Need / Hardware Contents... 3 Box Contents... 6 Assembling Your
More informationPlease read BOTH these Installation Instructions and the General Instructions before attempting to install or operate this equipment.
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who
More informationA59 APD & A86 CPD 5'X 16' SW ALUMINUM PORTA-DOCK
Page 1 of 5 PORTA-DOCK, INC. A59 APD & A86 CPD 5'X 16' SW ALUMINUM PORTA-DOCK *For Beige Decking Add the Letter B to model* Thank you for purchasing our product! *Please read these instructions and follow
More informationF i t t i n g t h e N e w L a n d i n g G e a r t o Y o u r S k y J i b V 1
F i t t i n g t h e N e w L a n d i n g G e a r t o Y o u r S k y J i b V 1 1 P a r t s L i s t : S t a n d a r d L a n d i n g G e a r U p g r a d e Product Code Parts + Spares Product Code Parts + Spares
More informationCopyright 2005 Valmont Industries, Inc.
Hose Drag TOPIVIEW OF CART Universal 1 Left Guidance Support (4" H.D.) 1732080... Left Guidance Sumort.. 16". H.D.)... 1732138 2 Right Guidance Support (4" H.D.)... 1732081 Right Guidance Support (6" H.D.)...
More informationC70 Window Roller Repair Taken from: Heres the problem:
C70 Window Roller Repair Taken from: http://www.volvospeed.com/vs_forum/topic/115086-how-to-c70-window-rollers-permanent-fix/ Heres the problem: This happened to two separate window assemblys on my c70
More informationMain Drive Components
Pipe and Bolt Threading Machine Main Drive Components 0 0 Rear Centering Head Centering Jaw Set Spiral Pins () 00 Centering Scroll Retaining Ring 0 Rear Bearing 0 Oil Ball Valve () # - x / Screw Motor
More informationRetractable Tongue Kit Model MPG457 Instructions
Malone MicroSport Trailer Retractable Tongue Kit Model MPG457 Instructions TM Take a few moments and read through these instructions to familiarize yourself with the step by step assembly process before
More informationMANUAL DE MONTAJE ASSEMBLY MANUAL AIREADOR DE PLUG AERATOR MODEL # AE-48T. Hardware & Parts Listing Assembly Instructions Maintenance Notes for
ASSEMBLY MANUAL Hardware & Parts Listing Assembly Instructions Maintenance Notes for 48 PLUG AERATOR MANUAL DE MONTAJE Lista de piezas y tornillería Instrucciones de armado Notas de mantenimiento para
More informationABM International, Inc.
ABM International, Inc. Lightning Stitch required 1 1.0: Parts List head and motor assembly (Qty. 1) Reel stand (Qty. 1) Needle bar frame clamp (Qty. 1) Motor drive (Qty. 1) 2 Cable harness with bracket
More information25-200H. 12 Planer / Jointer. with Helical Cutterhead. Parts List.
25-200H 12 Planer / Jointer with Helical Cutterhead 4001824 Parts List www.rikontools.com CABINET ASSEMBLY PARTS EXPLOSION & PARTS LIST KEY NO. DESCRIPTION KEY NO. DESCRIPTION 1 Pan Head Screw M6x12 P25-200H-1
More informationv1.0 ASSEMBLY GUIDE Mia Wide Bookcase
v1.0 ASSEMBLY GUIDE Mia Wide Bookcase Components Upon unpacking your bookcase from it s delivery box, you should have the pieces shown. Follow the steps on the next pages to assemble your new bookcase.
More informationInstallation Instructions
Installation Instructions Optima LED 8 Double-Sided StretchLite Perimeter Lit Graphic Display Line Voltage Connector Optima LED DS5 (Double-sided StretchLite Graphic Display) with Graphics Corner Bracket
More informationExploded Diagram /1/23
& Exploded Diagram www.firstdegreefitness.com 2018/1/23 Upper Frame Assembly A048 Seat Assembly A078 60806 60809 10097 A039 Lower Frame Assembly 10041 1 Nyloc Nut M10 10082 3 Washer M10x21x2 10097 1 Nut
More informationRYOBI 10 in. TABLE SAW - MODEL NO. BT3000
FOR MITER TABLE ASSEMBLY, REFER TO FIGURE 0 RYOBI 0 in. TABLE SAW - MODEL NO. BT000 FIGURE 5: 0 in. TABLE SAW FOR BLADE GUARD ASSEMBLY, REFER TO FIGURE FOR RIP FENCE ASSEMBLY, REFER TO FIGURE FOR MOTOR
More informationAX1001. Smith/Functional training Combo-free weight ASSEMBLY INSTRUCTIONS
AX1001 Smith/Functional training Combo-free weight ASSEMBLY INSTRUCTIONS EXPLODED DIAGRAM 83 84 84 85/86 87 87 88 89 90 91 62 64 64 64 64 64 64 65 65 65 65 66 66 65 66 66 65 63 63 66 67 68 55 66 66 70
More informationPassenger/Right Center and Rear Support Brackets. Driver/Left Center and
PARTS LIST: 1 Driver/Left HD Running Board 24 8mm x 24mm OD x 2mm Flat Washers 1 Passenger/Right HD Running Board 12 s 3 Driver/Left front, passenger center/rear Support Brackets 6 8mm-1.25 Hex Nuts 3
More informationWhite Quail Auto Trap
White Quail Auto Trap WARNING SAFETY, STORAGE & USE IF THE MAIN SPRING IS ATTACHED AND THE TRAP ARM IS IN THE 6 O CLOCK POSITION, THE TRAP IS ARMED AND EXTREME CAUTION IS REQUIRED. TO DISARM, TURN THE
More information535A. Main Components. Pipe and Bolt Threading Machine. Printed in U.S.A. Ridge Tool Company/Elyria, Ohio, U.S.A.
Pipe and Bolt Threading Machine A Main Components 0 Screw, Button Head /" - 0 x /" () Washer, Flat /" ()" Top Cover 0 Base Bottom Cover Screw, Pan Head # - x " () Carriage Assembly 0 Front Support Bar
More informationPORTA-DOCK, INC. AP17 APD DS 4 X 16 T12 AW17 CPD DS 4 X 16 T12
Page 1 of 7 PORTA-DOCK, INC. AP17 APD DS 4 X 16 T12 AW17 CPD DS 4 X 16 T12 *For Beige Decking Add the Letter B to Model* Thank you for purchasing out product! *Please read these instructions and follow
More informationSawStop. Contractor Fence Assembly OWNER S MANUAL. Model CNS-SFA
Contractor Fence Assembly OWNER S MANUAL Model CNS-SFA Warranty warrants to the original retail purchaser of the Contractor Fence Assembly accompanying this manual that the fence assembly will be free
More informationInstallation Instructions
Articulating Dual Monitor Mount Stand Installation Instructions UNPACKING Carefully open the carton, remove contents, and place them on a protected surface to avoid damage. Check the parts and the Supplied
More informationFan, Eden/Northfield, GS Installation Instructions (SKU ) Packing List
Packing List Blower Assembly Wiring Harness Rheostat with Nut and Knob Snap Disc Mounting Hardware (4) rubber grommets with brass inserts, (4) nuts, (4) washers. Cover Assembly Installation Warning: Make
More informationAssembly Instructions. GK2200T TREADMILL ASSEMBLY INSTRUCTIONS Frame Assembly 120V 220V
GK2200T TREADMILL ASSEMBLY INSTRUCTIONS Frame Assembly 120V 220V IMPORTANT SAFETY INSTRUCTIONS Read and understand all instructions and warnings prior to use. Obtain a medical exam before beginning any
More informationKwik-Lock. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.
Serving the Truck & Trailer Industry Since 1944 Installation Instructions Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 800-535-9545 www.aeroindustries.com
More informationINSTALLATION GUIDE FOR SR-CANOPY KIT SNOWRATOR
2018 INSTALLATION GUIDE FOR SR-CANOPY KIT SNOWRATOR AES L. T. RICH PRODUCTS 1/31/2018 Contents SR-CANOPY KIT INSTALLATION REV 1 1.0 SHIPPING CONTENTS... 2 2.0 IMPORTANT INFORMATION... 3 2.1 PURPOSE...
More informationMOTORIZED STANDARD SHADE WITH CABLES Installation Instructions
Tools Needed Drill Measuring Tape Pencil 2 Level Plumb Line ¼ Masonry Drill Bit Hammer Linesmans Pliers Cable Cutters Phillips & Flat-Head Screw Driver 11/32 Socket or Open End Wrench 5/32 Allen Wrench
More informationCalf-Tel Pen System Assembly Instructions
Calf-Tel Pen System Assembly Instructions (Instructions work for 4, 6, and the 7 Pen Systems) 1 ASSEMBLY OF PEN FRONT AND WALLS START THE ASSEMBLY BY LINING UP THE TWO UNI-DIRECTIONAL ARROWS IN THE TOP,
More informationFord Pick Up Rear leaf Spring Kit Installation Instructions
1948-1956 Ford Pick Up Rear leaf Spring Kit Installation Instructions 1-800-984-6259 www.totalcostinvolved.com Parts 48 inch leaf (2) springs (4) U-bolts 3/8-24 x l 1/4bolts (16) & nuts (2) 1/2-20 x 4
More informationPlease read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment.
Serial Number BX3231 2005-08 Pontiac G6 GT Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories
More informationWARNING. B as e plate s. BX Saturn L Series Installation Instructions. Serial Number
B as e plate s BX3323 Please read BOTH these and the General Instructions before attempting to install or operate this equipment. Serial Number 1. Blue Ox towing products and accessories are intended to
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS PARTS REQUIRED Single QuickStand Lite Parts A (1) Lower Arm A B C D B (1) Upper Arm C (1) Base D (1) Base Plate E (1) M8 Dynamic Arm Long F (1) Clamp Bracket G H (1) VESA Plate
More informationPlease read BOTH these Installation Instructions and the General Instructions before attempting to install or operate this equipment.
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who
More informationRYOBI 10 IN (254 MM) TABLE SAW MODEL NO. BT REPAIR SHEET
RYOBI 0 IN (2 MM) TABLE SAW MODEL NO. BT00- REPAIR SHEET 2 RYOBI 0 in. (2 mm) TABLE SAW - MODEL NO. BT00- FOR MITER TABLE ASSEMBLY, REFER TO FIGURE B FOR BLADE GUARD ASSEMBLY, REFER TO FIGURE E FOR RIP
More informationHardware and Components:
Hardware and Components: (A) 4X 5/16 x 1 Carriage Bolt (B) 2X 5/16 x 2-1/4 Carriage Bolt (C) 2X 5/16 x 3-1/4 Hex Bolt (D) 2X 5/16 x 3/4 Hex Bolt (E) 2X 5/16 x 1-1/4 Hex Bolt (F) 5/16 x 2-1/4 Hex Bolt (G)
More informationCode Product Qty 1 Top Vertex 3 2 Hot End Housing 1 3 Bottom Vertex 3 4 Print Platform Lock 3 5 End Stop Holder 3 6 Filament Feeder Motor Bracket 1 7
List of Parts Code Product Qty 1 680mm Extrusion 3 2 Power Supply 1 3 240mm Extrusion 9 4 42mm Nema 17 Stepper Motor 3 5 Slider-Hotend Connecting Rod 6 6 48mm Nema 17 Stepper Motor 1 7 Linear Rail with
More informationSPARE PARTS LIST MODEL NO. LB1200F PAGE 1 ITEM PART NO. DESCRIPTION QTY NOTE
PAGE 1 001 JM21000018 HEX.SOCKET HEAD SCREW M5X12 4 002 JM21000019 SPRING WASHER 5 4 003 JM21000020 FLAT WASHER 5 4 004 JM21000021 UP COVER COMPLETE 1 005 JM21000025 MICRO SWITCH FIX PANEL A 1 006 JM21000026
More informationSERVICE PARTS LIST PAGE 1 OF 6 BASE ASSEMBLY SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 12" DUAL BEVEL COMPOUND MITER SAW B27B
PAGE 1 OF 6 BASE ASSEMBLY 00 0 EXAMPLE: Component Parts (Small #) Are Included When Ordering The Assembly (Large #). SPECIFY CATALOG NO. AND NO. WHEN ORDERING PARTS = Part number change from previous service
More informationINSTRUCTION MANUAL LEG PRESS OPTION OF ELITE GYM
INSTRUCTION MANUAL LEG PRESS OPTION OF ELITE GYM QUESTION? As a quality home gym supplier we are committed to your complete satisfaction. If you have questions, or find missing or damaged parts, we will
More informationShapeoko XXL Assembly Guide
Shapeoko XXL Assembly Guide 04/27/2016 XXL Packing LIst Item Qty Description Y-Carriage (left) 1 Y-Carriage (right) 1 X/Z Assembly 1 40 Rail 3 1 rail has mounting holes for controller Wasteboard Half 2
More informationCustomer Notice: Congratulations again on your SawStop purchase, and thank you! -SawStop Tualatin, OR
Customer Notice: Congratulations on the purchase of this Sliding Crosscut Attachment. As the owner of a SawStop saw, you are familiar with our high standards for quality, fit and finish. Different from
More informationHERCULES EXTENDED TOWER
AmeriGlide Accessibility Solutions HERCULES EXTENDED TOWER ATION GUIDE Please read this installation guide carefully to ensure correct installation of the HERCULES EXTENDED TOWER Vertical Platform Lift.
More informationASSEMBLY AND ADJUSTMENT
EDGE MONITOR ARM EDGE Rev A 2/17 Model EDGE-SLV Model EDGE-BLK Model EDGE-WHT ASSEMBLY AND ADJUSTMENT EDGE MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and
More informationINSTALLATION INSTRUCTIONS 6 OVAL BENT END SIDEBARS DODGE RAM 1500, CREW CAB PART#: /241533B
PARTS LIST: 1 Driver/Left Sidebar 24 8mm x 24mm x 2mm Flat Washers 1 Passenger/Right Sidebar 12 8mm Lock Washers 3 Driver/left, Passenger Center and Rear 6 8mm Hex Nuts 3 INSTALLATION INSTRUCTIONS 6 OVAL
More informationBX3615. Subaru Impreza WRX (Include STI) Subaru 2012 Impreza Premium 2010 Outback Sport Installation Instructions Attachment Tab Height: 15
1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who are familiar with our products and have the equipment and knowledge necessary to do fit work. If needed, Blue
More information4099T Parts List. Front Bow Assy. (1) Rear Bow Assy. (1) Long Mounting Rail (2) Short Mounting Rail (2)
4099T Parts List Ver.2 Front Bow Assy. (1) Rear Bow Assy. (1) Small Mnt Foot (2) Large Mount Foot (2) Ladder Hook (2) Ladder Stop (2) Handle Extension (1) Long Mounting Rail (2) Short Mounting Rail (2)
More informationFlat Panel TV Cart Instruction Manual SKU: STAND-TV02D Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product. https://vivo-us.com/products/stand-tv02d
More informationSUT-1000CLC ASSEMBLY REQUIREMENTS
SUT-1000CLC Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and 3/4 combination wrenches, ratchet, 9/16, 3/4, 13/16, and 7/8 sockets. ASSEMBLY REQUIREMENTS *Torque all
More informationBX2520 Installation Instructions 2004 Mazda 3
BX2520 Installation Instructions 2004 Mazda 3 Serial No. The headlight assembly, front fascia, horn bracket and windshield washer reservoir are removed for baseplate installation. Drilling is required.
More informationRYOBI 10 in. (254 mm) TABLE SAW MODEL NO. BT3100 REPAIR SHEET
RYOBI 0 in. (4 mm) TABLE SAW MODEL NO. BT00 REPAIR SHEET FOR MITER TABLE ASSEMBLY, REFER TO FIGURE B FOR BLADE GUARD ASSEMBLY, REFER TO FIGURE E FOR RIP FENCE ASSEMBLY, REFER TO FIGURE C FOR MOTOR ASSEMBLY,
More informationOPERATOR'S MANUAL 46" SNOW BLADE. Model Numbers OEM IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
OPERATOR'S MANUAL 46" SNOW BLADE Model Numbers 190-833-OEM IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722 PRINTED IN U.S.A. FORM NO.
More informationPFT CABLE GYM INSTRUCTION MANUAL
PFT CABLE GYM INSTRUCTION MANUAL QUESTION? As a quality home gym supplier we are committed to your complete satisfaction. If you have questions, or find missing or damaged parts, we will guarantee your
More informationI NSTALLATION M ANUAL
Universal PVS Kit Star Trac Fitness E-TR, E-TBT, E-RB, and E-UB S-TR, S-TBT, S-RB, and S-UB I NSTALLATION M ANUAL STAR TRAC UNIVERSAL TV BRACKET INSTALLATION 1 TABLE OF CONTENTS Introduction...4 Before
More informationTITAN2-EDGE Public Access Computer Station Dual Track
TITAN2-EDGE Public Access Computer Station Dual Track TITAN2-EDGE Rev A 6/17 Model TITAN2-EDGE ASSEMBLY AND ADJUSTMENT TITAN2-EDGE PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the
More information