WOOD FRAMING ROOF+ SHEATHING and PANELING LAYOUTS

Size: px

Start display at page:

Download "WOOD FRAMING ROOF+ SHEATHING and PANELING LAYOUTS"

Archibald Holmes
5 years ago
Views:

1 WOOD FRAMING ROOF+ SHEATHING and PANELING LAYOUTS

Sheathing or paneling layouts can be easily

2 Sheathing and Paneling Layouts Wood Framing Roof+ automates sheathing and paneling layout creation. Sheathing or paneling layouts can be easily generated and split by existing joists or other predefined rules.

3 Sheathing and Paneling Layouts Sheathing or paneling is created using Revit Parts. In order to see the sheathing or paneling you have to select Show Parts or Show Both in View Properties Parts Visibility In the Element Properties you can find all information about every created sheathing/paneling segment. This information can later be used in tags and schedules.

4 Sheathing Configuration

5 Sheathing Configuration Sheathing Configuration allows user to configure and save settings for sheathing layouts. These settings can be saved and linked with roof layer using Roof Link.

6 Sheathing Configuration Sheathing Dimensions predefine vertical and horizontal sheathing sizes (Width and Length).

7 Sheathing Configuration Sheathing Layout predefine settings for Bottom and Top sheathing layers. There can be created up to two sheathing layers from each side. That s why there are separate settings for the first and second layer.

8 Sheathing Configuration First and Second sheathing layers can be predefined in the Roof Link using Sheathing and Sheathing II from Framing Layer column.

9 Sheathing Configuration Parallel or Perpendicular to Stud/Joist select if the sheathing should be parallel or perpendicular to the joist: Parallel is ticked Perpendicular is ticked

10 Sheathing Configuration Bottom/Base and Top/End Extension add an offset from the roof base or end.

11 Sheathing Configuration Placement Direction predefine sheathing direction: From Start, From End or From Both Sides. From Start From End

12 Sheathing Configuration Second Row Overlap Distance overlap distance between sheathing layouts if Perpendicular to Stud/Joist checkbox is ticked.

13 Sheathing Configuration Align with Studs/Joists aligns sheathing with Joists.

14 Sheathing Configuration Allow to Split on Second King/Joist splits the sheathing on the second king or joist of the opening.

15 Sheathing Configuration Always try to Split on Opening Side splits the sheathing on the opening side if top and bottom trimmers are predefined in the Opening Framing.

16 Sheathing Configuration You can predefine top and bottom trimmers under Roof+ Framing Configuration Opening Framing:

17 Sheathing Configuration Always Try to Merge Parts when ticked tries to merge parts if two parts share the same edge. Merged part size will not exceed the sheathing size which is predefined under Sheathing Dimensions.

18 Sheathing Configuration Mark Settings predefine default values for these parameters. The parameters can be later used in schedules and tags.

19 Sheathing Configuration Opening predefine top, bottom, left and right sheathing offsets from a window, door or MEP opening.

20 Sheathing Configuration End Connection predefine settings for sheathing start and end connections. Layer Extension distance from a roof face.

21 Split Sheathing/Paneling Parts

You just need to select a roof or any frame of a roof.

22 Split Sheathing/Paneling Parts Split Sheathing/Paneling Parts splits sheathing or paneling into the segments by predefined Sheathing Configuration or Paneling Condifuration. You just need to select a roof or any frame of a roof. To update the sheathing/paneling layout if there are any changes in the model or in Sheathing Configuration you have to load Split Sheathing Parts again.

23 Split Sheathing/Paneling Parts Sheathing or Paneling will be split if Split Parts is ticked in Roof Link.

24 Paneling Configuration

25 Paneling Configuration Paneling Configuration by using this configuration, you can model insulation and roof finishes, panels in your Revit project!

26 Paneling Configuration Using Paneling Configuration you can predefine insulation and external paneling setting for your Revit project. Insulation or panels are created using Revit Parts. In order to see the panels or insulation, you have to select Show Parts or Show Both in View Properties Parts Visibility

27 Paneling Configuration These settings can be saved and linked with roof layer using Roof Link.

28 Paneling Configuration Paneling Dimensions predefine vertical and horizontal paneling sizes (Width and Length).

29 Paneling Configuration Paneling Layout predefine settings for creation of the paneling.

30 Paneling Configuration Parallel or Perpendicular to Stud/Joist select if paneling should be parallel or perpendicular to the joist. Perpendicular is ticked Parallel is ticked

31 Paneling Configuration Bottom/Base and Top/End Extension add an offset from the roof base or end.

32 Paneling Configuration Division Offset adds division offset from the roof bottom. Available when Perpendicular to Stud/Joist checkbox is ticked.

33 Paneling Configuration Second Row Overlap Distance overlap distance between paneling layouts if Perpendicular to Stud/Joist is ticked.

34 Paneling Configuration Placement Direction predefine paneling direction: From Start, From End or From Both Sides. Make sure that Complete Sheets in First Row is switched on. From Start From End

35 Paneling Configuration Add First or Last Split Line adds the split profile into the first or last panel. ticked unticked

36 Paneling Configuration Horizontal and Vertical Gap specifies the distance between divided horizontal and vertical parts. The default value is 0, which results in no gap. Gap will be not valid if Always Try to Merge Parts is ticked on.

37 Paneling Configuration Horizontal and Vertical Division Profile apply the pre-loaded profile you select from the drop-down list to part edges along dividers. The default value is None.

38 Paneling Configuration Horizontal and Vertical Profile Edge Mirrored specify how the profiles on other side of a divider gap will be oriented. unticked ticked

39 Paneling Configuration Vertical Split On Opening Side splits panels along opening sides. ticked unticked

40 Paneling Configuration Vertical Split by Parameter - Split Part splits panels vertically by Split Part parameter from joist.

41 Paneling Configuration In order to activate Split Part parameter, you have to open Type Properties of the joist family and add Part Split Number. Now Roof+ will know where to split the panel, for example split the panel every 4 joists.

42 Paneling Configuration There are special families, which can be used for vertically or horizontally panel splitting. M_MF Part Split Stud-Joist (Metric for vertical splits) I_MF Part Split Stud-Joist (Imperial for vertical splits) M_MF Part Split Bridging (Metric for horizontal splits) I_MF Part Split Bridging (Imperial for horizontal splits)

43 Paneling Configuration Result: panels are split by vertical and horizontal joists and bridgings. For example, if the horizontal bridgings should be short, then please make sure Perpendicular to Stud/Joist is selected. In such case, Roof+ will split the segments vertically first and then horizontally.

44 Paneling Configuration Complete Sheets in First Row reverses panel placement direction. If Placement Direction is set to From Start and Complete Sheets in First Row is unticked, then the placement direction will be from end. This option should be used when there are a few insulation layers.

45 Paneling Configuration Align with Studs/Joists aligns panels with Joists.

46 Paneling Configuration Allow to Split on Second King/Joist splits the panels on the second king or joist of the opening.

47 Paneling Configuration Always try to Split on Opening Side splits the panels on the opening side if top and bottom trimmers are predefined in the Opening Framing.

48 Paneling Configuration You can predefine top and bottom trimmers under Roof+ Framing Configuration Opening Framing:

49 Paneling Configuration Always Try to Merge Parts merges two parts if they have the same edge. Merged part size will not exceed the panel size, which is predefined under Paneling Dimensions.

50 Paneling Configuration Mark Settings predefine default values for these parameters. The parameters can be later used in schedules and tags.

51 Paneling Configuration Opening predefine top, bottom, left and right paneling offsets from the window, door or MEP opening.

52 Paneling Configuration End Connection predefine settings for paneling start and end connections. Layer Extension distance from the roof face.

53 Other Features

54 Split Part by Selection Split Part by Selection splits selected sheathing or paneling layout by predefined placement direction From Start, From End, or From both Sides.

55 Reset Parts predefined to Split Reset Parts predefined to Split resets sheathing/paneling layout to a single part.

56 Reset All Parts Reset All Parts parts will be reset and eliminated from the roof.

57 Apply Extensions for Parts Apply Extensions for Parts resets sheathing or paneling parts and applies extensions. Extension values come from Sheathing or Paneling Configuration.

58 AGA CAD Ltd T: E: W:

WOOD FRAMING WALL+ SHEATHING and PANELING LAYOUTS

WOOD FRAMING WALL+ SHEATHING and PANELING LAYOUTS Sheathing and Paneling Layouts Wood Framing Wall+ automates sheathing and paneling layout creation. Sheathing or paneling layouts can be easily generated