Converting a solid to a sheet metal part tutorial

Size: px
Start display at page:

Download "Converting a solid to a sheet metal part tutorial"

Transcription

1 Converting a solid to a sheet metal part tutorial Introduction Sometimes it is easier to start with a solid and convert it to create a sheet metal part. This tutorial will guide you through the process and teach you how to use some of SpaceClaim's powerful tools to make your work easier, whether you're working with sheet metal parts or solids. In this tutorial, you will Create and shell a simple solid. Use the selection filter and power selection. Add corner reliefs to a sheet metal part. Convert edges to sheet metal bends and junctions. Create rips in the part so it can be unfolded. Unfold a sheet metal part. Create a simple solid 1. Select New > New Design from the Application menu to create a new design. 2. Draw a rectangle. a. Click the Rectangle tool in the Sketch group on the Design tab. b. Click a point on the grid to set the upper left corner of the rectangle. c. Move the mouse down and to the right to start drawing the rectangle. d. Type 40 for the first dimension (or 1.5 if you have your units set to Imperial). e. Press the Tab key and type 35 for the second dimension (or 1.3 if you have your units set to Imperial). f. Press Enter to finish drawing the rectangle.

2 3. Pull the rectangle into a solid. a. Click Pull in the Edit group on the Design tab. b. Select the rectangle and pull it up to 20 mm (or.75 inches). To type a dimension like you did when you drew the rectangle, start the pull and release the mouse, then type the dimension. 4. Now is a good time to save your design. a. Click the Application menu and click Save, or just click Save in the Quick access toolbar near the top left corner of the SpaceClaim window. b. Browse to the folder where you want to save the file. c. Type a file name and click Save. Add an opening and shell the solid 1. Copy the top edge of the block to create the edge for the opening: a. Click Pull in the Edit group on the Design tab. b. Double-click a top edge of the rectangle. c. This will select four contiguous edges. You can double-click again to cycle through the possible selections. Keep double-clicking until the top four edges are selected, like this: d. Select the Copy Edge option in the mini-toolbar or the Options panel. This option is shown in the mini-toolbar here:

3 e. Drag the edge about 7 mm (or.3 inches) toward the center of the top: 2. Shell the solid: This creates a copy of the edge that is offset from the original edge by the amount that you drag or type. a. Click Shell in the Insert group on the Design tab. b. Click the face you created by copying the edge: The solid will be shelled and the face you selected will be removed. Your solid should look similar to this: For now, leave the thickness at the default. You'll change it after you've converted the solid to a sheet metal part. Convert the solid to a sheet metal part and change its thickness 1. Right-click the component in the Structure tree that holds the solid and select Sheet Metal. This converts the solid into a sheet metal part. 2. Change the thickness of the part: a. Select the component in the Structure tree. b. Change the thickness of the part in the Sheet Metal section of the Properties panel, which is in the lower left side of the SpaceClaim window. If you are working in Metric units, change the thickness to 1mm and press Enter. If you are working in Imperial units, change the thickness to.04 and press Enter. These are the default thicknesses for sheet metal parts. You can use any thickness you like. To change the default, see Sheet Metal options.

4 Split the top face to add rips You must split the top face so the part can be unfolded. 1. Click Split Face in the Intersect group on the Design tab. 2. Select the top face of the part: 3. Click the Select Two Points tool guide on the right side of the Design window. 4. Select the two corners shown here: 5. The face is split between the two points and corner reliefs are automatically added. 6. Repeat these steps for each corner, so your part looks like this: Add bends and junctions Like splitting the top face, you must also add bends and junctions to unfold and manufacture the sheet metal part. 1. Start by adding junctions on the vertical edges: a. Click Pull in the Edit group on the Design tab.

5 b. Select one vertical edge: c. Click the Selection tab in the panel with the Structure tree. This tab is the power selection tool, and it helps you find similar geometry in your design. See Power selection for more information. d. Click Edges with same length: All of the vertical edges will be selected. e. Click the icon for a junction without overlap in the Options panel: 2. Add bends on the remaining hard edges: a. Draw a box around the entire part to select it.

6 b. Click Hard sheet metal edges in the Selection panel: All edges that don't have a junction type set are selected. In this example, all horizontal edges on the outside of the part are selected. c. Click the icon for a bend junction type in the Options panel: Your part now has junctions and bends so it can be unfolded: Unfold the sheet metal part Right-click the part in the Design window and select Unfold Part. Your unfolded part should look similar to this:

Modeling an Airframe Tutorial

Modeling an Airframe Tutorial EAA SOLIDWORKS University p 1/11 Difficulty: Intermediate Time: 1 hour As an Intermediate Tutorial, it is assumed that you have completed the Quick Start Tutorial and know how to sketch in 2D and 3D. If

More information

g. Click once on the left vertical line of the rectangle.

g. Click once on the left vertical line of the rectangle. This drawing will require you to a model of a truck as a Solidworks Part. Please be sure to read the directions carefully before constructing the truck in Solidworks. Before submitting you will be required

More information

TUTORIAL 4: Combined Axial and Bending Problem Sketch Path Sweep Initial Project Space Setup Static Structural ANSYS

TUTORIAL 4: Combined Axial and Bending Problem Sketch Path Sweep Initial Project Space Setup Static Structural ANSYS TUTORIAL 4: Combined Axial and Bending Problem In this tutorial you will learn how to draw a bar that has bends along its length and therefore will have both axial and bending stresses acting on cross-sections

More information

Alibre Design Tutorial - Simple Extrude Step-Pyramid-1

Alibre Design Tutorial - Simple Extrude Step-Pyramid-1 Alibre Design Tutorial - Simple Extrude Step-Pyramid-1 Part Tutorial Exercise 4: Step-Pyramid-1 [text version] In this Exercise, We will set System Parameters first. Then, in sketch mode, outline the Step

More information

Getting Started Guide

Getting Started Guide SOLIDWORKS Getting Started Guide SOLIDWORKS Electrical FIRST Robotics Edition Alexander Ouellet 1/2/2015 Table of Contents INTRODUCTION... 1 What is SOLIDWORKS Electrical?... Error! Bookmark not defined.

More information

Part 2: Earpiece. Insert Protrusion (Internal Sketch) Hole Patterns Getting Started with Pro/ENGINEER Wildfire. Round extrusion.

Part 2: Earpiece. Insert Protrusion (Internal Sketch) Hole Patterns Getting Started with Pro/ENGINEER Wildfire. Round extrusion. Part 2: Earpiece 4 Round extrusion Radial pattern Chamfered edge To create this part, you'll use some of the same extrusion techniques you used in the lens part. The only difference in this part is that

More information

Alibre Design Tutorial: Loft, Extrude, & Revolve Cut Loft-Tube-1

Alibre Design Tutorial: Loft, Extrude, & Revolve Cut Loft-Tube-1 Alibre Design Tutorial: Loft, Extrude, & Revolve Cut Loft-Tube-1 Part Tutorial Exercise 5: Loft-Tube-1 [Complete] In this Exercise, We will set System Parameters first, then part options. Then, in sketch

More information

Modeling Basic Mechanical Components #1 Tie-Wrap Clip

Modeling Basic Mechanical Components #1 Tie-Wrap Clip Modeling Basic Mechanical Components #1 Tie-Wrap Clip This tutorial is about modeling simple and basic mechanical components with 3D Mechanical CAD programs, specifically one called Alibre Xpress, a freely

More information

Pull Down Menu View Toolbar Design Toolbar

Pull Down Menu View Toolbar Design Toolbar Pro/DESKTOP Interface The instructions in this tutorial refer to the Pro/DESKTOP interface and toolbars. The illustration below describes the main elements of the graphical interface and toolbars. Pull

More information

Creo Revolve Tutorial

Creo Revolve Tutorial Creo Revolve Tutorial Setup 1. Open Creo Parametric Note: Refer back to the Creo Extrude Tutorial for references and screen shots of the Creo layout 2. Set Working Directory a. From the Model Tree navigate

More information

Cube in a cube Fusion 360 tutorial

Cube in a cube Fusion 360 tutorial Cube in a cube Fusion 360 tutorial n Before using these instructions, it is helpful to watch this video screencast of the CAD drawing actually being done in the software. Click to link to the video tutorial.

More information

Copyright by J.W. Zuyderduyn - How To Model a Yacht in SolidWorks? Page 1

Copyright by J.W. Zuyderduyn   - How To Model a Yacht in SolidWorks? Page 1 Copyright by J.W. Zuyderduyn www.yachttutorial.com - How To Model a Yacht in SolidWorks? Page 1 Copyright by J.W. Zuyderduyn www.yachttutorial.com - How To Model a Yacht in SolidWorks? Page 2 Download

More information

Canoe Mirroring Lofts

Canoe Mirroring Lofts Canoe Mirroring Lofts 1. Set Units to Inches 2. Create a New Design. 3. Save the Design as canoeinl811 in your Canoe folder. 4. Create a New Sketch on the Frontal Workplane. Name the Sketch Middle. 5.

More information

AEROPLANE. Create a New Folder in your chosen location called Aeroplane. The four parts that make up the project will be saved here.

AEROPLANE. Create a New Folder in your chosen location called Aeroplane. The four parts that make up the project will be saved here. AEROPLANE Prerequisite Knowledge Previous knowledge of the following commands is required to complete this lesson. Sketching (Line, Rectangle, Arc, Add Relations, Dimensioning), Extrude, Assemblies and

More information

Using Siemens NX 11 Software. The connecting rod

Using Siemens NX 11 Software. The connecting rod Using Siemens NX 11 Software The connecting rod Based on a Catia tutorial written by Loïc Stefanski. At the end of this manual, you should obtain the following part: 1 Introduction. Start NX 11 and open

More information

Name: Date Completed: Basic Inventor Skills I

Name: Date Completed: Basic Inventor Skills I Name: Date Completed: Basic Inventor Skills I 1. Sketch, dimension and extrude a basic shape i. Select New tab from toolbar. ii. Select Standard.ipt from dialogue box by double clicking on the icon. iii.

More information

Lesson 10: Loft Features

Lesson 10: Loft Features 10 Goals of This Lesson Your students will be able to create the following part: profiles chisel This lesson plan corresponds to the Loft Features chapter of SolidWorks Getting Started. SolidWorks Student

More information

Introduction to Parametric Modeling AEROPLANE. Design & Communication Graphics 1

Introduction to Parametric Modeling AEROPLANE. Design & Communication Graphics 1 AEROPLANE Design & Communication Graphics 1 Object Analysis sheet Design & Communication Graphics 2 Aeroplane Assembly The part files for this assembly are saved in the folder titled Aeroplane. Open an

More information

Principles and Practice

Principles and Practice Principles and Practice An Integrated Approach to Engineering Graphics and AutoCAD 2011 Randy H. Shih Oregon Institute of Technology SDC PUBLICATIONS www.sdcpublications.com Schroff Development Corporation

More information

Part 8: The Front Cover

Part 8: The Front Cover Part 8: The Front Cover 4 Earpiece cuts and housing Lens cut and housing Microphone cut and housing The front cover is similar to the back cover in that it is a shelled protrusion with screw posts extruding

More information

Module 2: Radial-Line Sheet-Metal 3D Modeling and 2D Pattern Development: Right Cone (Regular, Frustum, and Truncated)

Module 2: Radial-Line Sheet-Metal 3D Modeling and 2D Pattern Development: Right Cone (Regular, Frustum, and Truncated) Inventor (5) Module 2: 2-1 Module 2: Radial-Line Sheet-Metal 3D Modeling and 2D Pattern Development: Right Cone (Regular, Frustum, and Truncated) In this tutorial, we will learn how to build a 3D model

More information

Welcome to SPDL/ PRL s Solid Edge Tutorial.

Welcome to SPDL/ PRL s Solid Edge Tutorial. Smart Product Design Product Realization Lab Solid Edge Assembly Tutorial Welcome to SPDL/ PRL s Solid Edge Tutorial. This tutorial is designed to familiarize you with the interface of Solid Edge Assembly

More information

Revit Structure 2013 Basics

Revit Structure 2013 Basics Revit Structure 2013 Basics Framing and Documentation Elise Moss Supplemental Files SDC P U B L I C AT I O N S Schroff Development Corporation Better Textbooks. Lower Prices. www.sdcpublications.com Tutorial

More information

SolidWorks 95 User s Guide

SolidWorks 95 User s Guide SolidWorks 95 User s Guide Disclaimer: The following User Guide was extracted from SolidWorks 95 Help files and was not originally distributed in this format. All content 1995, SolidWorks Corporation Contents

More information

Module 1G: Creating a Circle-Based Cylindrical Sheet-metal Lateral Piece with an Overlaying Lateral Edge Seam And Dove-Tail Seams on the Top Edge

Module 1G: Creating a Circle-Based Cylindrical Sheet-metal Lateral Piece with an Overlaying Lateral Edge Seam And Dove-Tail Seams on the Top Edge Inventor (10) Module 1G: 1G- 1 Module 1G: Creating a Circle-Based Cylindrical Sheet-metal Lateral Piece with an Overlaying Lateral Edge Seam And Dove-Tail Seams on the Top Edge In Module 1A, we have explored

More information

SolidWorks Design & Technology

SolidWorks Design & Technology SolidWorks Design & Technology Training Course at PHSG Ex 5. Lego man Working with part files 8mm At first glance the Lego man looks complicated but I hope you will see that if you approach a project one

More information

1. Creating geometry based on sketches 2. Using sketch lines as reference 3. Using sketches to drive changes in geometry

1. Creating geometry based on sketches 2. Using sketch lines as reference 3. Using sketches to drive changes in geometry 4.1: Modeling 3D Modeling is a key process of getting your ideas from a concept to a read- for- manufacture state, making it core foundation of the product development process. In Fusion 360, there are

More information

Sheet metal tutorial. To set the bend radius Right click on the first sheet metal icon in the command manager and specify a bend radius or 1mm.

Sheet metal tutorial. To set the bend radius Right click on the first sheet metal icon in the command manager and specify a bend radius or 1mm. Sheet metal tutorial In the following tutorial you will cover the basic features of the Solid Works sheet metal tool by modelling the component shown opposite. Activating Sheet metal mode Sheet metal components

More information

SolidWorks Part I - Basic Tools SDC. Includes. Parts, Assemblies and Drawings. Paul Tran CSWE, CSWI

SolidWorks Part I - Basic Tools SDC. Includes. Parts, Assemblies and Drawings. Paul Tran CSWE, CSWI SolidWorks 2015 Part I - Basic Tools Includes CSWA Preparation Material Parts, Assemblies and Drawings Paul Tran CSWE, CSWI SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered

More information

Getting Started. Right click on Lateral Workplane. Left Click on New Sketch

Getting Started. Right click on Lateral Workplane. Left Click on New Sketch Getting Started 1. Open up PTC Pro/Desktop by either double clicking the icon or through the Start button and in Programs. 2. Once Pro/Desktop is open select File > New > Design 3. Close the Pallet window

More information

Introduction to 3D CAD with SolidWorks. Jianan Li

Introduction to 3D CAD with SolidWorks. Jianan Li Introduction to 3D CAD with SolidWorks Jianan Li Create a New Part The first time you launch SolidWorks, it asks you to set the default units and dimension standard. Make sure you have IPS and ANSI selected,

More information

Engineering & Computer Graphics Workbook Using SolidWorks 2014

Engineering & Computer Graphics Workbook Using SolidWorks 2014 Engineering & Computer Graphics Workbook Using SolidWorks 2014 Ronald E. Barr Thomas J. Krueger Davor Juricic SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org)

More information

On completion of this exercise you will have:

On completion of this exercise you will have: Prerequisite Knowledge To complete this exercise you will need; to be familiar with the SolidWorks interface and the key commands. basic file management skills the ability to rotate views and select faces

More information

SolidWorks Navigation

SolidWorks Navigation SolidWorks Basics SolidWorks Navigation Command Bar Feature Tree Model Window Simple Box Select the Front plane Create a new sketch Create a Center Rectangle from the origin Smart Dimension the length

More information

Introduction to Autodesk Inventor for F1 in Schools (Australian Version)

Introduction to Autodesk Inventor for F1 in Schools (Australian Version) Introduction to Autodesk Inventor for F1 in Schools (Australian Version) F1 in Schools race car In this course you will be introduced to Autodesk Inventor, which is the centerpiece of Autodesk s Digital

More information

Engineering & Computer Graphics Workbook Using SOLIDWORKS

Engineering & Computer Graphics Workbook Using SOLIDWORKS Engineering & Computer Graphics Workbook Using SOLIDWORKS 2017 Ronald E. Barr Thomas J. Krueger Davor Juricic SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org)

More information

Starting a 3D Modeling Part File

Starting a 3D Modeling Part File 1 How to Create a 3D Model and Corresponding 2D Drawing with Dimensions, GDT (Geometric Dimensioning and Tolerance) Symbols and Title Block in SolidWorks 2013-2014 By Edward Locke This tutorial will introduce

More information

Autodesk Medical Center

Autodesk Medical Center Autodesk Medical Center Page 1 Contents Autodesk Medical Center... 1 Revit Projects... 3 Exercise 1 Create a new project file... 3 Datum Elements... 4 Exercise 2 Add Grids... 5 Exercise 3 Edit Levels...

More information

Appendix B: Autocad Booklet YR 9 REFERENCE BOOKLET ORTHOGRAPHIC PROJECTION

Appendix B: Autocad Booklet YR 9 REFERENCE BOOKLET ORTHOGRAPHIC PROJECTION Appendix B: Autocad Booklet YR 9 REFERENCE BOOKLET ORTHOGRAPHIC PROJECTION To load Autocad: AUTOCAD 2000 S DRAWING SCREEN Click the start button Click on Programs Click on technology Click Autocad 2000

More information

Symbols and Standards (Architectural CAD)

Symbols and Standards (Architectural CAD) Design and Drafting Description In this activity the teacher will give an orientation to the symbols and conventions of Architectural CAD. Industry common symbols are used for most of the fixtures and

More information

for Solidworks TRAINING GUIDE LESSON-9-CAD

for Solidworks TRAINING GUIDE LESSON-9-CAD for Solidworks TRAINING GUIDE LESSON-9-CAD Mastercam for SolidWorks Training Guide Objectives You will create the geometry for SolidWorks-Lesson-9 using SolidWorks 3D CAD software. You will be working

More information

Alternatively, the solid section can be made with open line sketch and adding thickness by Thicken Sketch.

Alternatively, the solid section can be made with open line sketch and adding thickness by Thicken Sketch. Sketcher All feature creation begins with two-dimensional drawing in the sketcher and then adding the third dimension in some way. The sketcher has many menus to help create various types of sketches.

More information

Chapter 6 Title Blocks

Chapter 6 Title Blocks Chapter 6 Title Blocks In previous exercises, every drawing started by creating a number of layers. This is time consuming and unnecessary. In this exercise, we will start a drawing by defining layers

More information

Prasanth. Lathe Machining

Prasanth. Lathe Machining Lathe Machining Overview Conventions What's New? Getting Started Open the Part to Machine Create a Rough Turning Operation Replay the Toolpath Create a Groove Turning Operation Create Profile Finish Turning

More information

Autodesk Inventor Module 17 Angles

Autodesk Inventor Module 17 Angles Inventor Self-paced ecourse Autodesk Inventor Module 17 Angles Learning Outcomes When you have completed this module, you will be able to: 1 Describe drawing inclined lines, aligned and angular dimensions,

More information

Visio 2010 Tutorial. Design of PLS Systems

Visio 2010 Tutorial. Design of PLS Systems Visio 2010 Tutorial ISE 453 Design of PLS Systems This tutorial is designed to teach you to use Visio to draw a facility layout. It was adapted for Visio by Derek Shields and for older Visio versions by

More information

Introduction to Sheet Metal Features SolidWorks 2009

Introduction to Sheet Metal Features SolidWorks 2009 SolidWorks 2009 Table of Contents Introduction to Sheet Metal Features Base Flange Method Magazine File.. 3 Envelopment & Development of Surfaces.. 14 Development of Transition Pieces.. 23 Conversion to

More information

EXERCISE ONE: BEACH BUGGY.

EXERCISE ONE: BEACH BUGGY. EXERCISE ONE: BEACH BUGGY. Prerequisite knowledge Students should have completed Exercises from the file: Introduction to Assemblies Concept Mates Focus of lesson Commands Used This lesson will focus on

More information

2809 CAD TRAINING: Part 1 Sketching and Making 3D Parts. Contents

2809 CAD TRAINING: Part 1 Sketching and Making 3D Parts. Contents Contents Getting Started... 2 Lesson 1:... 3 Lesson 2:... 13 Lesson 3:... 19 Lesson 4:... 23 Lesson 5:... 25 Final Project:... 28 Getting Started Get Autodesk Inventor Go to http://students.autodesk.com/

More information

< Then click on this icon on the vertical tool bar that pops up on the left side.

< Then click on this icon on the vertical tool bar that pops up on the left side. Pipe Cavity Tutorial Introduction The CADMAX Solid Master Tutorial is a great way to learn about the benefits of feature-based parametric solid modeling with CADMAX. We have assembled several typical parts

More information

Drawing with precision

Drawing with precision Drawing with precision Welcome to Corel DESIGNER, a comprehensive vector-based drawing application for creating technical graphics. Precision is essential in creating technical graphics. This tutorial

More information

Creo Extrude Tutorial 2: Cutting and Adding Material

Creo Extrude Tutorial 2: Cutting and Adding Material Creo Extrude Tutorial 2: Cutting and Adding Material 1. Open Creo Parametric 2. File > Open > extrudeturial (From Creo Extrude Tutorial 1) 3. Cutting Material a. Click Extrude Icon > Select the following

More information

Sheet Metal OverviewChapter1:

Sheet Metal OverviewChapter1: Sheet Metal OverviewChapter1: Chapter 1 This chapter describes the terminology, design methods, and fundamental tools used in the design of sheet metal parts. Building upon these foundational elements

More information

Learning Guide. ASR Automated Systems Research Inc. # Douglas Crescent, Langley, BC. V3A 4B6. Fax:

Learning Guide. ASR Automated Systems Research Inc. # Douglas Crescent, Langley, BC. V3A 4B6. Fax: Learning Guide ASR Automated Systems Research Inc. #1 20461 Douglas Crescent, Langley, BC. V3A 4B6 Toll free: 1-800-818-2051 e-mail: support@asrsoft.com Fax: 604-539-1334 www.asrsoft.com Copyright 1991-2013

More information

Solid Part Four A Bracket Made by Mirroring

Solid Part Four A Bracket Made by Mirroring C h a p t e r 5 Solid Part Four A Bracket Made by Mirroring This chapter will cover the following to World Class standards: Sketch of a Solid Problem Draw a Series of Lines Finish the 2D Sketch Extrude

More information

Introduction to CATIA V5

Introduction to CATIA V5 Introduction to CATIA V5 Release 17 (A Hands-On Tutorial Approach) Kirstie Plantenberg University of Detroit Mercy SDC PUBLICATIONS Schroff Development Corporation www.schroff.com Better Textbooks. Lower

More information

Excel Lab 2: Plots of Data Sets

Excel Lab 2: Plots of Data Sets Excel Lab 2: Plots of Data Sets Excel makes it very easy for the scientist to visualize a data set. In this assignment, we learn how to produce various plots of data sets. Open a new Excel workbook, and

More information

Appendix R5 6. Engineering Drafting. Broken View

Appendix R5 6. Engineering Drafting. Broken View Updating Using Autodesk Inventor to Release 5 Appendix R5 6 Engineering Drafting Chapter 6 delineates the concepts of engineering drafting. You output orthographic views from solid parts and orthographic

More information

Drawing a Plan of a Paper Airplane. Open a Plan of a Paper Airplane

Drawing a Plan of a Paper Airplane. Open a Plan of a Paper Airplane Inventor 2014 Paper Airplane Drawing a Plan of a Paper Airplane In this activity, you ll create a 2D layout of a paper airplane. Please follow these directions carefully. When you have a question, reread

More information

Part Design. Sketcher - Basic 1 13,0600,1488,1586(SP6)

Part Design. Sketcher - Basic 1 13,0600,1488,1586(SP6) Part Design Sketcher - Basic 1 13,0600,1488,1586(SP6) In this exercise, we will learn the foundation of the Sketcher and its basic functions. The Sketcher is a tool used to create two-dimensional (2D)

More information

Lesson 6 2D Sketch Panel Tools

Lesson 6 2D Sketch Panel Tools Lesson 6 2D Sketch Panel Tools Inventor s Sketch Tool Bar contains tools for creating the basic geometry to create features and parts. On the surface, the Geometry tools look fairly standard: line, circle,

More information

Product Modelling in Solid Works

Product Modelling in Solid Works Product Modelling in Solid Works In the following exercise you will use solid works to construct the computer mouse shown opposite. In this exercise you will use a number of advanced features to achieve

More information

Revit Structure 2012 Basics:

Revit Structure 2012 Basics: SUPPLEMENTAL FILES ON CD Revit Structure 2012 Basics: Framing and Documentation Elise Moss autodesk authorized publisher SDC PUBLICATIONS www.sdcpublications.com Schroff Development Corporation Structural

More information

teachweld Trainer Section 2: Usability Brought to you by Realityworks, Inc., the experiential learning technology company

teachweld Trainer Section 2: Usability Brought to you by Realityworks, Inc., the experiential learning technology company teachweld Trainer Section 2: Usability Brought to you by Realityworks, Inc., the experiential learning technology company Page 1: Title Page Page 2: : Login Instruction Page 3: teachweld Modes Title Page

More information

From the above fig. After sketching the path and profile select the sweep command First select the profile from property manager tree And then select

From the above fig. After sketching the path and profile select the sweep command First select the profile from property manager tree And then select Chapter 5 In sweep command there is a) Two sketch profiles b) Two path c) One sketch profile and one path The sweep profile is used to create threads springs circular things and difficult geometry. For

More information

Copyrighted. Material. Copyrighted. Material. Copyrighted. Material. Copyrighted. Material

Copyrighted. Material. Copyrighted. Material. Copyrighted. Material. Copyrighted. Material ENGINEERING & COMPUTER GRAPHICS WORKBOOK Using SolidWorks 2008 Ronald E. Barr Thomas J. Krueger Theodore A. Aanstoos Davor Juricic SDC PUBLICATIONS Schroff Development Corporation www.schroff.com Better

More information

Toothbrush Holder. A drawing of the sheet metal part will also be created.

Toothbrush Holder. A drawing of the sheet metal part will also be created. Prerequisite Knowledge Previous knowledge of the following commands is required to complete this lesson; Sketch (Line, Centerline, Circle, Add Relations, Smart Dimension,), Extrude Boss/Base, and Edit

More information

Copyrighted. Material. Copyrighted. Material. Copyrighted. Material. Copyrighted. Material

Copyrighted. Material. Copyrighted. Material. Copyrighted. Material. Copyrighted. Material ENGINEERING & COMPUTER GRAPHICS WORKBOOK Using SolidWorks 2005 Ronald E. Barr Thomas J. Krueger Theodore A. Aanstoos Davor Juricic SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com

More information

AutoCAD Civil 3D 2009 ESSENTIALS

AutoCAD Civil 3D 2009 ESSENTIALS AutoCAD Civil 3D 2009 ESSENTIALS SDC PUBLICATIONS Schroff Development Corporation www.schroff.com Better Textbooks. Lower Prices. Alignments and Profiles Section 2: Profiles In this section you learn how

More information

Alibre Design Exercise Manual Introduction to Sheet Metal Design

Alibre Design Exercise Manual Introduction to Sheet Metal Design Alibre Design Exercise Manual Introduction to Sheet Metal Design Copyrights Information in this document is subject to change without notice. The software described in this documents is furnished under

More information

J. La Favre Fusion 360 Lesson 4 April 21, 2017

J. La Favre Fusion 360 Lesson 4 April 21, 2017 In this lesson, you will create an I-beam like the one in the image to the left. As you become more experienced in using CAD software, you will learn that there is usually more than one way to make a 3-D

More information

BIM - ARCHITECTUAL IMPORTING A SCANNED PLAN

BIM - ARCHITECTUAL IMPORTING A SCANNED PLAN BIM - ARCHITECTUAL IMPORTING A SCANNED PLAN INTRODUCTION In this section, we will demonstrate importing a plan created in another application. One of the most common starting points for a project is from

More information

Chapter 2. Drawing Sketches for Solid Models. Learning Objectives

Chapter 2. Drawing Sketches for Solid Models. Learning Objectives Chapter 2 Drawing Sketches for Solid Models Learning Objectives After completing this chapter, you will be able to: Start a new template file to draw sketches. Set up the sketching environment. Use various

More information

Inventor-Parts-Tutorial By: Dor Ashur

Inventor-Parts-Tutorial By: Dor Ashur Inventor-Parts-Tutorial By: Dor Ashur For Assignment: http://www.maelabs.ucsd.edu/mae3/assignments/cad/inventor_parts.pdf Open Autodesk Inventor: Start-> All Programs -> Autodesk -> Autodesk Inventor 2010

More information

Getting Started. Before You Begin, make sure you customized the following settings:

Getting Started. Before You Begin, make sure you customized the following settings: Getting Started Getting Started Before getting into the detailed instructions for using Generative Drafting, the following tutorial aims at giving you a feel of what you can do with the product. It provides

More information

Engineering Technology

Engineering Technology Engineering Technology Introduction to Parametric Modelling Engineering Technology 1 See Saw Exercise Part 1 Base Commands used New Part This lesson includes Sketching, Extruded Boss/Base, Hole Wizard,

More information

Introduction to ISDX Interactive Surface Design Extension Creo 2.0. Level 7 Continued

Introduction to ISDX Interactive Surface Design Extension Creo 2.0. Level 7 Continued Introduction to ISDX Interactive Surface Design Extension Creo 2.0 Level 7 Continued Create or modify your config.pro (or edit and save a config.pro) such that the graphics driver is changed to opengl.

More information

Activity 1 Modeling a Plastic Part

Activity 1 Modeling a Plastic Part Activity 1 Modeling a Plastic Part In this activity, you will model a plastic part. When completed, your plastic part should look like the following two illustrations. While building this model, take time

More information

When you complete this assignment you will:

When you complete this assignment you will: Objjectiives When you complete this assignment you will: 1. Set-up menus and drawing for designing modeling problems. 2. become familiar with the Sketch menu tools and commands. 3. Produce a three-dimensional

More information

SolidWize. Online SolidWorks Training. Lofts: Tea Pot

SolidWize. Online SolidWorks Training. Lofts: Tea Pot SolidWize Online SolidWorks Training Lofts: Tea Pot Step 1: Creating the Body Using inches as the unit, create the following sketch on the top plane. We will now add a plane above the top plane so that

More information

Explanation of buttons used for sketching in Unigraphics

Explanation of buttons used for sketching in Unigraphics Explanation of buttons used for sketching in Unigraphics Sketcher Tool Bar Finish Sketch is for exiting the Sketcher Task Environment. Sketch Name is the name of the current active sketch. You can also

More information

DEPARTMENT OF MECHANICAL AND INDUSTRIAL ENGINEERING NORTHEASTERN UNIVERSITY

DEPARTMENT OF MECHANICAL AND INDUSTRIAL ENGINEERING NORTHEASTERN UNIVERSITY DEPARTMENT OF MECHANICAL AND INDUSTRIAL ENGINEERING NORTHEASTERN UNIVERSITY CAPSULE PROGRAM Funded by NSF grant #0833636 Tutorial 02 3D Part Modeling SolidWorks 2010 Copyright 2010 Prof. Zeid 3D Part Modeling

More information

Pro/DESKTOP Tutorial Drafting Bow Compass

Pro/DESKTOP Tutorial Drafting Bow Compass Pro/DESKTOP Tutorial Drafting Bow Compass Michael Flowers 2005 1 Objectives: To develop confidence with the Pro/DESKTOP software. To learn to utilize extrude, project, revolve, round, and chamfer features.

More information

PRODIM CT 3.0 MANUAL the complete solution

PRODIM CT 3.0 MANUAL the complete solution PRODIM CT 3.0 MANUAL the complete solution We measure it all! General information Copyright All rights reserved. Apart from the legally laid down exceptions, no part of this publication may be reproduced,

More information

Engineering Design. with SolidWorks A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling

Engineering Design. with SolidWorks A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling INSIDE: MultiMedia CD An audio/visual presentation of the tutorial projects Engineering Design with SolidWorks 2010 A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling Introductory Level

More information

Table of Contents. Lesson 1 Getting Started

Table of Contents. Lesson 1 Getting Started NX Lesson 1 Getting Started Pre-reqs/Technical Skills Basic computer use Expectations Read lesson material Implement steps in software while reading through lesson material Complete quiz on Blackboard

More information

with MultiMedia CD Randy H. Shih Jack Zecher SDC PUBLICATIONS Schroff Development Corporation

with MultiMedia CD Randy H. Shih Jack Zecher SDC PUBLICATIONS Schroff Development Corporation with MultiMedia CD Randy H. Shih Jack Zecher SDC PUBLICATIONS Schroff Development Corporation WWW.SCHROFF.COM Lesson 1 Geometric Construction Basics AutoCAD LT 2002 Tutorial 1-1 1-2 AutoCAD LT 2002 Tutorial

More information

Module 1C: Adding Dovetail Seams to Curved Edges on A Flat Sheet-Metal Piece

Module 1C: Adding Dovetail Seams to Curved Edges on A Flat Sheet-Metal Piece 1 Module 1C: Adding Dovetail Seams to Curved Edges on A Flat Sheet-Metal Piece In this Module, we will explore the method of adding dovetail seams to curved edges such as the circumferential edge of a

More information

ARCHICAD Introduction Tutorial

ARCHICAD Introduction Tutorial Starting a New Project ARCHICAD Introduction Tutorial 1. Double-click the Archicad Icon from the desktop 2. Click on the Grey Warning/Information box when it appears on the screen. 3. Click on the Create

More information

Table of Contents. Dedication Preface. Chapter 1: Introduction to CATIA V5-6R2015. Chapter 2: Drawing Sketches in the Sketcher Workbench-I.

Table of Contents. Dedication Preface. Chapter 1: Introduction to CATIA V5-6R2015. Chapter 2: Drawing Sketches in the Sketcher Workbench-I. Table of Contents Dedication Preface iii xvii Chapter 1: Introduction to CATIA V5-6R2015 Introduction to CATIA V5-6R2015 1-2 CATIA V5 Workbenches 1-2 System Requirements 1-4 Getting Started with CATIA

More information

Managing images with NewZapp

Managing images with NewZapp Managing images with NewZapp This guide is for anyone using the NewZapp Fixed editor as opposed to the Drag and Drop editor. The Image Manager is where images are uploaded and stored in your NewZapp account

More information

SolidWorks Reference Geometry

SolidWorks Reference Geometry SolidWorks Reference Geometry IDeATe Laser Micro Part 2 Dave Touretzky and Susan Finger 1. Symmetry and Reference Geometry Today, you ll make this part bear-like face and then cut it on the laser cutter:

More information

How to create a cove for cove lighting in DIALux In this tutorial you will learn how to make a cove similar to the one in the following image

How to create a cove for cove lighting in DIALux In this tutorial you will learn how to make a cove similar to the one in the following image How to create a cove for cove lighting in DIALux In this tutorial you will learn how to make a cove similar to the one in the following image The cove dimension will be 4 meter by 5 meter and the other

More information

BEST PRACTICES COURSE WEEK 14 PART 2 Advanced Mouse Constraints and the Control Box

BEST PRACTICES COURSE WEEK 14 PART 2 Advanced Mouse Constraints and the Control Box BEST PRACTICES COURSE WEEK 14 PART 2 Advanced Mouse Constraints and the Control Box Copyright 2012 by Eric Bobrow, all rights reserved For more information about the Best Practices Course, visit http://www.acbestpractices.com

More information

Lab 3 Introduction to SolidWorks I Silas Bernardoni 10/9/2008

Lab 3 Introduction to SolidWorks I Silas Bernardoni 10/9/2008 1 Introduction This lab is designed to provide you with basic skills when using the 3D modeling program SolidWorks. You will learn how to build parts, assemblies and drawings. You will be given a physical

More information

Rhinoceros modeling tools for designers. Using Layouts in Rhino 5

Rhinoceros modeling tools for designers. Using Layouts in Rhino 5 Rhinoceros modeling tools for designers Using Layouts in Rhino 5 RH50-TM-LAY-Apr-2014 Rhinoceros v5.0, Layouts, Training Manual Revised April 8, 2014, Mary Fugier mary@mcneel.com Q&A April 8, 2014, Lambertus

More information

Drawing Layouts Paper space & Model Space

Drawing Layouts Paper space & Model Space Drawing Layouts Paper space & Model Space Users of Bricscad will have seen the tabs at the bottom left of the drawings area labelled: Model, Layout1, Layout2 but may not know how to use them or what they

More information