FORMAX. FD1400 AutoSeal MAINTENANCE MANUAL FIRST EDITION 11/2007

Transcription

1 FORMAX FD1400 AutoSeal 11/2007 MAINTENANCE MANUAL FIRST EDITION

2 Table of Contents 1400 Shown with Optional Stand Page: 1. Description / Unpacking and Set up 2. Controls / Operation 3. Fold Plate Adjustment / Setting Custom Folds 4. Sealer Roller Clearance / Replacing In-feed Rollers 5. Replacing Singulator Pad / Replacing Cork Pad / Replacing Sealer Rollers 6. Replacing Fold Rollers / Belt Adjustment and Replacement 7. Photo Eye Replacement / Photo Eye Sensitivity Adjustment 8. Daily Maintenance / Troubleshooting Troubleshooting Parts Lists / Schematic

3 DESCRIPTION Paper side guides Top Cover Upper Fold Plate In-feed table Lower Fold Plate Control Panel FUNCTION: The 1400 Folder / Sealer folds and seals many different configurations including, "C", "Z", V and custom folds. It may also use several different sizes of forms. For configurations and / or paper sizes see listing under specifications below. SPECIFICATIONS: Maximum foldable paper size Fold styles Paper loading capacity Speed Machine Weight Power Supply 14" length x 8.5" width "C", "Z", "V" and custom folds Up to 100 sheets Up to 60 sheets per minute 82 lb. 120 volts, 50/60 Hz, 3.5 amps. UNPACKING AND SET UP 1. Check package for shipping damage. If there is shipping damage, do not discard the box. 2. CAUTION: Two people must lift machine out of the box. 3. Plug cord into machine and into wall outlet. 1

4 CONTROLS Start.. Starts machine. Stop.. Stops machine. Ready light.. Steady green when power is on Blinks red when cover is open or fault is detected. OPERATION 1. Adjust fold plates to desired fold for length of paper (see fold plate adjustment on page 3). To do this, loosen the two thumbscrews (figure 3a & b) on each fold plate. Align center bar (figure 3a & b) so the marks on each side match up. For V folds remove the lower fold plate, turn around 180 and reinstall. 2. Make sure fold plates and cover are reinstalled properly. 3. Plug in cord and turn power on (figure 1). 4. To make sure folds are in the correct location, push the paper feed lever (figure 2) down and place one form onto the in-feed table and press the start button. Adjust fold plates if necessary (see fold plate adjustment on page 3). 5. Push the paper feed lever down and load paper neatly stacked and squared on to the in-feed table. Paper can be stacked up to 100 sheets. Note: Standard "Z" fold forms can be loaded face up or down with the glue edge leading. All "C" fold forms must be loaded face up with glue edge leading. 6. Be sure the ready light is green and press the start button to begin operation. (figure 1) (figure 2) 2

5 FOLD PLATE ADJUSTMENT Upper Fold Plate Lower Fold Plate Thumbscrews Bar (figure 3a) (figure 3b) 1. To adjust the first fold remove the top cover. If the first fold is too long loosen the two thumbscrews on the upper fold plate and slide the bar down. If the fold is too short loosen the thumbscrews and slide the bar up. NOTE: The bar should be on the same marks on each side. 2. To adjust the second fold remove the lower fold plate. If the second fold is too long loosen the two thumbscrews and slide the bar up. If the fold is too short loosen the thumbscrews and slide the bar down. NOTE: The bar should be on the same marks on each side. 3. For quick setup of C, Z and V folds refer to the blue lines on the fold plate. SETTING CUSTOM FOLDS Eccentric "Z" Uneven "C" / Return Mailer *Extended fold plate is needed to process this form 1. Measure the length of panel "A" 2. Adjust the upper fold plate so that the bar lines up with the measurements of panel "A" i.e. if panel "A" is 5 1/4" long move the bar up or down so that it lines up with the 5 1/4" mark on the fold plate. 3. Measure the length of panel "B" 4. Adjust the lower fold plate so that the bar lines up with the measurements of panel "B". 5. Load forms and press start (refer to OPERATION on page 2). Panel "A" Panel "B" 1. Measure the length of panel "A" & "B" 2. Adjust the upper fold plate so that the bar lines up with the measurements of panel "A" & "B" i.e. if panel "A" & "B" are 10 1/2" long move the bar up or down so that it lines up with the 10 1/2" mark on the fold plate. 3. Measure the length of panel "B" 4. Adjust the lower fold plate so that the bar lines up with the measurements of panel "B". 5. Load forms and press start (refer to OPERATION on page 2). Panel "A" Panel "B" 3

6 ROLLER CLEARANCE 1. Turn power off and unplug the power cord. 2. Loosen locking nuts on the top plates. (figure 4) 3. Insert a feeler gauge (0.001") into space between the rollers. (figure 4) 4. Turn adjusting bolts while checking clearance with the feeler gauge. (figure 4) 5. Tighten the locking nuts in place after proper clearance has been set. (figure 4) NOTE: (Double-check spacing with feeler gauge. Left to right fine-tuning is required.) TO REPLACE IN-FEED ROLLERS 1. Turn power off and unplug the power cord. 2. Remove top cover and non-operator cover. 3. Loosen lock bolt inside top cover. 4. Pull up clamp. 5. Remove retaining ring on gear. (see folder roller pg. 6) 6. Remove gear and chain. (see folder roller pg. 6) 7. Loosen individual rollers (one screw each) 8. Pull roller bar through each roller in the direction of the re-moved gear. 9. To reassemble repeat above steps in reverse. 4

7 TO REPLACE SINGULATOR PAD Singulator pad Cork pad (figure 5) 1. Remove in-feed rollers (see in-feed rollers on pg. 4) 2. Remove rubber singulator pad (figure5), a screwdriver or knife may be need to pry the pad off. 3. Clean singulator mount. 4. Apply supper glue to singulator pad and singulator mount. 5. Apply singulator pad to singulator mount, let sit for at least five minutes before reinstalling in-feed rollers. 6. Reinstall in-feed rollers (see in-feed rollers pg. 4) TO REPLACE CORK PAD 1. Lower in-feed tray. 2. Remove old cork pad (figure 5), a screwdriver or knife may be needed to pry the pad off. 3. Clean area of removed pad. 4. Apply super glue to cork pad and in-feed tray. 5. Apply cork pad to in-feed table. Let sit for at least five minutes before operating the machine. TO REPLACE SEALER ROLLERS 1. Turn power off and unplug power cord. 2. Remove covers and upper fold plate. 3. Remove belts (see belt replacement pg. 7). 4. Remove top plates by unscrewing four screws. 5. Loosen or remove the five lower screws on each side. 5

8 6. Remove first roller by lifting up and out of machine. 7. Remove the two springs. 8. To remove second roller tilt stainless steel center plate away from roller. 9. Remove second roller the same way as the first roller. 10. To reassemble repeat above steps in reverse. 11. Adjust belt tension (see belt replacement pg. 7). TO REPLACE FOLDER ROLLERS 1. Turn power off and unplug power cord. 2. Remove covers and remove upper fold plate. 3. Remove control panel. 4. Remove belt (see belt replacement pg. 7). 5. Remove C rings on gears and sprocket. 6. Remove sprocket and chain. 7. Remove plastic gears. 8. Remove bearing springs on both ends of rollers bearing plate (operator side). 9. Pull out rollers. 10. To reassemble repeat above steps in reverse. BELT ADJUSTMENT AND REPLACEMENT NOTE: Roller clearance must be set before adjusting belt tension. 1. Loosen pivot screw on idler lever turn adjusting screw until belt is loose enough to remove. 2. Install new belt, turn adjusting screw until belt has 5/16 play, tighten pivot screw. NOTE: Be sure not to over tighten belt, it will affect roller clearance 6

9 PHOTO EYE REPLACEMENT (figure 6) A single photo eye, just before the pressure rollers is used for counting, last form time out and fault detection (i.e. doubles) figure Loosen the screw on the guide plate. 2. Carefully remove the screw and the photo eye. 3. Unplug the wires and discard old photo eye and reinstall the new photo eye. 4. Reverse the previous step to reinstall the new photo eye. 5. Adjust the photo eye to 1/8 below the guide plate. 6. Then tighten the screw to insure the photo eye does not move. PHOTO EYE SENSITIVITY ADJUSTMENT 1. Remove operator cover, place a form over the sensor 2. Adjust small blue square box located on the control board using a small screwdriver (until beam lamp is lit). Note: Always adjust sensor when installing a new photo eye. 7

10 DAILY MAINTENANCE 1. It is recommended to let forms cool for one-half hour, from the laser printer, before folding and sealing. This allows toner to set on the forms, and static electricity to discharge. A 400 Series Jogger is recommended for best results. The Jogger squares the forms and dissipates heat and static created by laser printers. 2. If toner builds up on the metal sealer rollers clean the rollers with a lint-free cloth dampened sparingly with a mild household cleaner. 3. Clean in-feed wheels and fold rollers with Formax recommended roller cleaner & rejuvenator to remove paper dust and toner. A damp cloth with water is the best alternative. CAUTION: Do not use any chemicals other than the roller cleaner & rejuvenator or water. TROUBLESHOOTING A. Clearing paper jams: WARNING: Turn machine off and unplug cord from its receptacle 1. If a jam occurs in between the metal sealing rollers remove any remaining forms from the hopper. Remove the top cover and the upper fold plate. Remove the jam-clearing tool (located under top fold plate), apply the tool to the upper metal roller (figure 7) and turn clockwise (Caution: do not turn counter clockwise or rollers may be damaged) until the paper jam is clear. Remove the jammed form and return tool in holder and reinstall the upper fold plate. Reinstall cover and press the start button. Note: Press the black button (figure 8) near the power cord inlet to reset the breaker if necessary. (figure 7) (figure 8) 2. If a jam occurs in the fold plates remove fold plate and remove paper. Reinstall fold plate. 8

11 B. Fold Quality Needs Improving: 1. Make sure paper is squared and installed correctly. Side guides should be evenly balanced and snug against the paper. B1. If folds are still incorrect adjust fold. 1. Take a piece of plain copy paper paper; mark the leading edge, (first edge of paper to feed into machine) 2. Run the paper through the machine. 3. Place a pressure seal form on the top cover of machine. 4. Place the piece of plain paper, just processed, on top of the pressure seal form aligning the leading edge of both forms (see diagram below). 5. Check to see if folds on the plain paper line up with the fold perforations of the pressure seal form (see figure 9 below). If the folds on the plain paper & fold perforations on the pressure seal forms do not line up adjust the fold plates (see fold plate adjustment on pg. 3). 6. Once the adjustments have been made, take one pressure seal form and test it. 7. Tear open processed form and inspect to see if they line up with the fold perforations. Note: Repeat the above process until the folds on plain paper line up with the perforations on the form. Pressure Seal Form 1 st fold - C 1 st fold Z Leading edge w/ glue line 2 nd fold C & Z Plain Copy Paper (figure 9) 9

12 C. Paper is not Folding Square (Skewing): (figure 8) 1. If paper pulls left or right adjust the skew adjuster. To adjust the skew, turn the skew adjuster (figure 8) left or right until the paper is feeding correctly. D. Machine plugged in, no power 1. Turn machine on. 2. Make sure top cover is installed properly. 3. Press the circuit breaker. 4. Check wall outlet. 5. Remove operator cover check the fuse located on control board next to transformer. 6. Check all electrical connections. E. Power on, ready light is blinking red: 1. Check to see that the top cover is installed properly. 2. Check to insure that the photo-eye, before the metal sealer rollers, is clear of forms and/or paper dust. 3. Check for Paper jam. 4. Motor may be overheated F. Ready light is not illuminated and power is on: 1. Press the black button (figure 8) near the power cord inlet to reset the breaker. G. Double feeding / Mis-feeding 1. Clean feed wheel (soap and water) a. Check center in-feed roller and singulator pad for wear. Replace the pad if it is cupped. b. Check to see if center in-feed roller is centered on the gate tip. 2. Run a stack of plain paper, this is done to check on proper feeding. If double feeding does not occur on the paper: a. Check to make sure pressure seal forms are not sticking together. Jogging or hand separating may be necessary to determine this. b. Hand separate about 50 forms, align and test run the forms. If no double feeding occurs proper forms handling is necessary. 10

13 3. If double feeding continues to occur, the next step is to check the gate tip pressure. 4. With the in-feed tray pushed down and free of forms, spin the center in-feed roller. You are looking for a minimal drag. 5. Make sure singulator mount is sitting straight on bracket. If crooked, loosen the two screws and adjust until straight. 6. To evaluate operation of the singulator/gate tip assembly: a. Turn off machine and unplug. b. Remove lower fold plate. c. Reach hand up underneath paper feed tray. You will feel the gate tip adjusting screw; back off the screw about 3 turns. d. Press down on the gate tip and remove your finger. The gate tip should go down and spring up again. If it doesn t work smoothly, determine where it s binding and correct the problem. NOTE: Increase the spring tension on the singulator assembly by moving the springs up one more notch. 7. After you have determined that the singulator assembly is operating smoothly, readjust the gate tip adjusting screw. Back off pressure on the gate-tip untilit moves freely up and down. With paper in-feed tray in lowered position, turn screw to tighten until the gate-tip no longer moves up and down. 8. Reinstall the lower fold plate. Place a stack of unprinted forms on the feed tray and test run. You are looking for consistent feeding with no hesitation and no double feeding. 9. If needed, fine tune adjustments can be made by turning the gate tip adjusting screw in small increments until you get the desired results. H. Overriding photo-sensors with shunts: Shunts have been provided in case of photo sensor failure. See page 15 for shunt storage location. 1. To override jam detection place shunt onto both pins of JP1. 2. To override paper out place shunt onto both pins of JP2. Caution: It is NOT recommended to operate machine for extended period of time in override mode, replace photo sensor as soon as possible. JP2 JP1 BEAM ADJUST BEAM LAMP COVER CLOSED LAMP FUSE 11

14 ITEM PART DESCRIPTION QTY NON-OPERATOR COVER OPERATOR COVER TOP COVER PAPER TRAY EXTENSION FORMAX INLAY INLAY SIDE COVER MOUNTING SCREWS 8 12

15 1400 SCHEMATIC ELECTRICAL COMPONENTS ITEM PART # DESCRIPTION QTY. * POWER SUPPLY CORD 1 * WIRE HARNESS * WIRE HARNESS LOW VOLT 1 * PHOTO EYE HARNESS 1 * ROCKER SWITCH 1 * SPEED CONTROL 1 * /6 HP MOTOR 1 * CIRCUIT BREAKER 3.5 AMP. 1 * IEC INLET 1 * PROXIMITY SENSOR 1 13

16 ITEM PART# DESCRIPTION QTY CROSS-MEMBER, REAR BASE CATCH TRAY ASSY STATIC BRUSH ROLLER GUARD MAGNET, ACTUATOR STATIC BRUSH MOUNTING SCREWS

17 8 9 26b b ITEM PART # DESCRIPTION QTY. ITEM PART # DESCRIPTION QTY PHOTO SENSOR HARNESS NUT 1/ SENSOR BRACKET COLLAR SHOULDER SCREW SKEW PIVOT BRKT TRAY PUSH DOWN SKEW ADJ THUMBSCREW PAPER GUIDE OP SIDE ASSY FEEDER PAPER RAMP ASSY PAPER TRAY EXTENSION PAPER TRAY SHAFT PAPER TRAY ASSY WITH CORK SPRING PAPER GUIDE PAPER GUIDE DRIVE SIDE ASSY ROLLER ROD, FEED BUSHING SELF ALIGN GREY CENTER HARD-COMPOUND FEED WHEEL VINYL BUSHING 2 26b BLACK SOFT-COMPUND FEED WHEEL CROSS-MEMBER, FRONT CORK PAD CONTROL PANEL MOUNT RETAINER BRKT BRACE SHAFT SCREW PPH 6-32 x 3/ NUT SELF LOCK PAPER RAMP GUIDE CURVED WASHER SCREWS FOR PAPER RAMP GUIDE SKEW PIVOT SPACERS FOR PAPER RAMP GUIDE PIVOT BRKT SKEW ADJUSTMENT SHAFT

18 DETAIL A ** SHUNTS 3 7 ITEM PART # DESCRIPTION QTY SPRING BRKT SPRING BRKT FRAME OP SIDE EXTENSION. SPRING.188 O.D EXTENSION SPRING. 375 O.D SHOULDER SCREW # ROCKER SW D.P.S.T. (nonilluminated) 1 DETAIL A DETAIL A ITEM PART # DESCRIPTION QTY SINGULATOR ARM SINGULATOR PAD SINGULATOR MOUNT SINGULATOR BRACKET T KNOB COMPRESSION SPRING

19 ITEM PART # DESCRIPTION QTY DRIVE ROLLER ASSY ROLLER, UPPER ASSY BRACKET SIDE, FRAME CAP SPRING, BEARING BLOCK PULLEY, 13T.38 PITCH JAM CLEARING TOOL TIMING BELT DOUBLE SIDED BOLT 3/8X1 1/4" SOC. HD. SC /8" X 1 1/4" HEX HD /8"-40 HEX JAM NUT #10-32 X 1.00, SOC HD CAP ¼-20 KEP. NUT PULLEY, 11T.38 PITCH IDLER PULLEY, 11T.38 PITCH ASSY TOOH IDLER ASSY ¼ LOCK WASHER ¼-20 x 1 SOC.HD 2 17

20 ITEM PART # DESCRIPTION QTY BUSHING FOLDER ROLLER FLANGE BUSHING DRIVE ROLLER COMP. SPRING FOLDER ROLLER BEARING PLATE

21 ITEM PART # DESCRIPTION QTY PROXIMITY SENSOR E CLIP SIDE PLATE RETAINING RING SPRING BRKT IEC POWER INLET SHOULDER SCREW RETAINING RING FRAME, DRIVE SIDE NON-SWIVEL GLIDE /6 H.P. MOTOR PULLEY 9L CIRCUIT BREAKER 3.5 AMP PULLEY 28L SPRING BRKT GEAR BELT 210 LO COMBO 45/15 SPROCKET T. SPROCKET ASSY T. SPROCKET CHAIN ¼ PITCH MASTER LINK ¼-20 KEP NUT 4 19

22 LOWER FOLD PLATE 14 UPPER FOLD PLATE 14 LOWER FOLD PLATE ITEM PART DESCRIPTION QTY. * LOWER FOLD PLATE ASSY LOWER/LOWER FOLD PLATE LOWER/UPPER FOLD PLATE UPPER ADJUST PLATE LOWER ADJUST PLATE FOLD PLATE BUMPER CLAMPING KNOB SCREW PPH 6-32x1/ LOWER FOLD PLATE DECAL FOLD DIVERTER SCREW PPH 6-32x3/ UPPER FOLD PLATE ITEM PART DESCRIPTION QTY. * " UPPER FOLD PLATE ASSY UPPER/LOWER FOLD PLATE 14" UPPER/UPPER FOLD PLATE 14" UPPER FOLD PLATE DECAL UPPER ADJUST PLATE LOWER ADJUST PLATE FOLD PLATE BUMPER CLAMPING KNOB SCREW PPH 6-32x1/ H-01 SELF ADHESIVE BUMPER 2 20

23 1 HOLES FOR LOCATING COUNTER 2 BATTERY MOUNT ITEM PART # DESCRIPTION QTY CONTROL BOARD LCD COUNTER COUNTER BATTERY AMP FUSE 5 x

24