x9 (+1 EXTRA) GSKY VERSA WALL - INTRO KIT PARTS LIST VK-0 TRIM KIT TRAY / HARDWARE KIT REQUIRED TOOL LIST (NOT INCLUDED)

Transcription

1 TRIM KIT VERSA KIT BACKING 3'-4 7/8" VERSA KIT 7" CORDOVA PINE SIDE TRIM 7 /4" VERSA KIT 7" CORDOVA PINE TOP/BOTTOM TRIM 7 /4" VERSA KIT 4" BOTTOM EDGE TRIM 4" REQUIRED TOOL LIST (NOT INCLUDED) * UTILITY KNIFE * FT LEVEL * STUD FINDER * STRAIGHT EDGE 3-0 / 4-0 3'-4 7/8" 3'-6 3/8" TRAY / HARDWARE KIT VERSA 8-POT TRAY TRIM LIGHT BRACE TRIM HEAVY BRACE #7 X -/" #8 X 5/8" # PHILLIPS /4" BIT DRIVER VERSA TRAY BACKING TRIM SCREW DRIVER BIT PLUG SCREW (CROSS) DOUBLE BEAD CATCH x9 (+ EXTRA) VERSA TRAY FITTING VERSA TRAY SCREW (USE /4" BIT DRIVER) x0 x40 x6 x4 x0 x00 x x x x PARTS LIST S: VK-0

2 VERSA BACKING 3'-4 7/8" TYPICAL STUD SPACING IS 6" OR 4". 3'- /4" INDENTIFY BACKING MOUNTING LOCATION MARK LOCATION OF VERSA BACKING ON THE WALL TO LOCATE STUDS; USE STUD FINDER BACK * PENCIL / PEN * FT LEVEL * STUD FINDER FINAL DIMENSIONS WILL BE 3/4" LARGER ON EACH SIDE INCLUDING TRIM ALIGN BACKING ON THE WALL VERSA BACKING LOCATION ON THE WALL ALIGN VERSA BACKING ON THE WALL S: VK-

3 VERSA BACKING STUD SPACE STUD SPACE IF A SECOND STUD CANNOT BE FOUND, DRY WALL ANCHORS SHOULD BE USED FOR ADDITIONAL SUPPORT. 3'-4 7/8" 3'- /4" DRAW STUD LOCATION ON BACKING SHOULD BE ABLE TO HIT MIN. STUDS 0" 0" DRAW HORIZONTAL 0" O/C VERSA BACKING 0" VERSA BACKING BACK 0" '- 5/8" '-8 7/6" 3 5/8" * PENCIL / PEN * STRAIGHT EDGE STUD LOCATION ON VERSA BACKING SCREW LOCATION ON VERSA BACKING LOCATE STUDS AND SCREW LOCATIONS AND MARK S: VK-

4 VERSA BACKING #7 X -/" PHILLIPS SCREW USING #7 X /" PHILLIPS SCREWS, MOUNT VERSA BACKING ON THE WALL * FT LEVEL * # PHILLIPS DRIVER BIT (INCLUDED) FASTENERS FOR NON-WOOD / STEEL STUD ARE NOT INCLUDED FASTEN VERSA BACKING VERSA BACKING FINISHED FASTEN VERSA BACKING TO WALL S: VK-3

5 VERSA CORDOVA PINE TOP/BOTTOM TRIM 3'-4 7/8" 4" '-4 7/6" '-4 7/6" 4" /" VERSA CORDOVA PINE TOP / BOTTOM TRIM TRIM LIGHT BRACE TRIM LIGHT BRACE ATTACH IN THE MIDDLE OF THE TRIM FOR SECURING CORNERS LATER ALIGN THE EDGE OF TRIM LIGHT BRACE TO /" GUIDE LINE #8# X 5/8" ROBERTSON SCREW; SCREWS PER FACE " #8 X 5/8" TRIM SCREW /" #8 X 5/8" ROBERTSON SCREW; SCREWS PER FACE * PENCIL / PEN * # PHILLIPS DRIVER BIT (INCLUDED) TRIM LIGHT BRACE ON TOP / BOTTOM TRIM TRIM LIGHT BRACE (USE SHORTER SIDE ON TRIM) ALIGN EDGE OF TRIM TO VERSA BACKING +- /4" REVEAL (GAP) TOP / BOTTOM TRIM ON VERSA BACKING /4" ATTACH WITH TRIM LIGHT BRACES TO VERSA TOP/BOTTOM TRIM S: VK-4

6 TRIM HEAVY BRACE INSTALL TRIM HEAVY BRACE BETWEEN TRIM LIGHT TOP / BOTTOM TRIM TRIM HEAVY BRACE #8 X 5/8" TRIM SCREW #8 X 5/8" ROBERTSON SCREW; SCREWS PER FACE * PENCIL / PEN * # PHILLIPS DRIVER BIT (INCLUDED) TRIM HEAVY BRACE IS ONLY FOR TOP / BOTTOM TRIM (NOT FOR SIDE TRIM) TRIM HEAVY BRACE ON TOP / BOTTOM TRIM SECURE VERSA TOP/BOTTOM TRIM WITH TRIM HEAVY BRACE S: VK-5

7 VERSA CORDOVA PINE SIDE TRIM TRIM LIGHT BRACE #8 X 5/8" TRIM SCREW 4" '-8 3/8" '-8 3/8" 4" 4" '-8 3/8" '-8 3/8" 4" #8 X 5/8" ROBERTSON SCREW; SCREWS PER FACE VERSA CORDOVA PINE SIDE TRIM ALIGN THE EDGE OF VERSA BACKING TO TRIM LIGHT VRACE MAKE SURE TO ALIGN THE FACE OF SIDE TRIM TO BOTH TOP / BOTTOM TRIM * PENCIL / PEN * # PHILLIPS DRIVER BIT (INCLUDED) TRIM LIGHT BRACE ON VERSA BACKING USE LONGER SIDE ON VERSA BACKING SIDE TRIM ALIGN THE FACE OF SIDE TRIM TO TOP / BOTTOM TRIM ATTACH TRIM LIGHT BRACE TO BACKING TO MOUNT SIDE TRIM S: VK-6

8 TRIM LIGHT BRACE #8 X 5/8" TRIM SCREW TRIM LIGHT BRACE FASTEN TRIM LIGHT BRACES TO SIDE TRIM PIECES ALIGN AND HOLD CORNERS TIGHTLY AS FASTENING THE SCREWS #8 X 5/8" ROBERTSON SCREW; SCREWS PER FACE * PENCIL / PEN * # PHILLIPS DRIVER BIT (INCLUDED) TRIM LIGHT CORNER /4" SECURE AND ALIGN TRIM CORNERS WITH TRIM LIGHT BRACES VK-7

9 TRIM CATCH BLOCK #6 X /" PHILLIPS SCREW ALIGN TRIM CATCH BLOCK TO PILOT HOLES * # PHILLIPS DRIVER BIT (INCLUDED) TRIM CATCH BLOCK ATTACH TRIM CATCH BLOCKS FOR 4" BOTTOM FACE TRIM S: VK-8

10 VERSA 4" BOTTOM EDGE TRIM TRIM CATCH TAB PILOT HOLE STRIKE PLATES ALIGN BOTTOM EDGE TRIM TO BOTTOM TRIM * # PHILLIPS DRIVER BIT (INCLUDED) VERSA 4" BOTTOM EDGE TRIM PREPARATION #6 X 5/8" PHILLIPS SCREW VERSA 4" BOTTOM EDGE TRIM ADD STRIKE PLATES TO 4" BOTTOM FACE TRIM AND ATTACH S: VK-9

11 BOTTOM TRAY ALL OTHER TRAYS VERSA 8-POT TRAY LOCK NUT FROM INSIDE INSERT RUBBER O-RING FROM BACK OF TRAY VERSA TRAY FITTING INSERT VERSA TRAY PLUG FROM THE FRONT SIDE OF VERSA TRAY x x 8 HAND TIGHT ONLY MAKE SURE THAT O-RING IS NOT SQUISHED OUT VERSA TRAY PLUG NONE VERSA TRAY WITH VERSA TRAY PLUG WILL BE USED AT BOTTOM OF GREEN WALL ENSURE THAT TRAY FITTING IS ANGLED AT A 45 DEGREE ANGLE TRAY ASSEMBLY - VERSA TRAY PLUG TRAY ASSEMBLY - VERSA TRAY FITTING ASSEMBLE VERSA 8-POT TRAYS S: VK-0

12 VERSA 8-POT TRAY (VERSA TRAY PLUG) 3/4" LOCATE OUTSIDE CORNER OF TRAY TO MARKED POSITION USING VERSA TRAY SCREW (4 SCREWS / TRAY), FASTENVERSA TRAY ONTO VERSA BACKING VERSA TRAY SCREW ALIGN TOP TRAY EDGE WITH MARKEDLINE DRAW 7" FROM EDGE OF VERSA BACKING 7" DRAW 3/4" FROM EDGE OF VERSA BACKING * PENCIL / PEN * FT LEVEL * STRAIGHT EDGE * /4 BIT DRIVER VERSA 8-POT TRAY LOCATION MAKE SURE TO USE VERSA TRAY WITH VERSA TRAY PLUG AT THE BOTTOM OF THE WALL VERSA 8-POT TRAY INSTALLATION ALIGN AND INSTALL BOTTOM TRAY S: VK-

13 USE 4 SCREW / TRAYS CHECK EACH TRAY TO BE LEVEL WHILE INSTALLING VERSA 8-POT TRAY (VERSA TRAY FITTING) USE GROOVES TO ALIGN SUBSEQUENT TRAYS (CONFIRM POSITION WITH A LEVEL PRIOR TO FASTENING) VERSA TRAY SCREW ENSURE THE TRAY Y FITTING IS ON A 45 DEGREE ANGLE * FT LEVEL * /4 BIT DRIVER VERSA 8-POT TRAY MOUNTING VERSA 8-POT TRAYS INSTALLED 3 BOTTOM EDGE TRIM ATTACHED COMPLETE TRAY INSTALLATION S: VK-

14 PLANTS ARE NOT INCLUDED IN THE PACKAGE, PLEASE SOURCE LOCALLY PLANTS INSTALL PLANTS S: VK-3

15 ADDENDUM THAT THE SHARPIE INCLUDED IS NOT MEANT FOR MARKING, BUT RATHER FOR LINKING MULTIPLE KITS TOGETHER AND FOR WOOD TOUCHUPS. PLEASE THAT THERE IS ONLY ONE () VERSA TRAY PLUG INCLUDED, NOT FIVE (5) GV-0 THIS WAS UPDATED ON GV-: GV- THIS WAS ADDED TO GV- : SHARPIE (FOR TOUCH-UP AND COLORING WOOD CUTS) x VERSA TRAY PLUG x TYPICAL STUD SPACING IS 6" OR 4". IF A SECOND STUD CANNOT BE FOUND, DRY WALL ANCHORS SHOULD BE USED FOR ADDITIONAL SUPPORT. THE QUANTITY OF TRAYS THAT REQUIRE A FITTING TO BE ASSEMBLED WAS UPDATED FROM X7 TO X9: GV-0 THIS WAS ADDED TO GV-: THE DRAINS ON THE TRAYS SHOULD ALL BE AT A 45 DEGREE ANGLE ONCE ASSEMBLED AND INSTALLED. IF THEY ARE NOT, ENSURE THAT THEY ARE ANGLED THIS WAY BY HAND AFTER INSTALLATION. DRAINAGE FITTING INSTALLED PROPERLY x 9 CHECK EACH TRAY TO BE LEVEL WHILE INSTALLING GV- GV- ADDENDUM TO INSTRUCTIONS INCLUDED IN BOX