Specifications. Model

Transcription

1 KS500/1000 ZIP/Zero ODP/LPCB Standing Seam Roof System Standard External and Internal Environments Aluminium External / Steel Liner - LPS Grade EXT-B NBS Format Specification H43 - Metal Composite Panel Cladding/Covering To be read with Preliminaries/General conditions. 122A - Metal Composite Roof Cladding Drawing reference(s): Supports: Cold rolled purlins, minimum 1.5mm thick Bearing width: Minimum 50mm Pitch: Min 1.5 or above (Finished roof slope after deflections). Manufacturer and reference: Kingspan Limited, roof cladding system for standard internal and external non-corrosive environments and Loss Prevention Certification Board certified to LPS 1181 Grade EXT-B. Test results: LPS 1181: 2003: Part 1: Issue 1, ceiling lining tests: Passed all requirements. Panels: Profile reference: KS500/1000 ZIP/Zero ODP/LPCB - Kingzip Insulated Standing Seam Roof Panel. Cover width: 500mm/1000mm External facings: Material: Aluminium to BS EN 485, BS EN 515, BS EN 1396, 3105 ALLOY H46. Thickness: 0.9mm Finish/Colour: Mill finish Stucco Embossed with lacquer. Internal facings: Material: Hot-dip zinc coated steel to BS EN Thickness: 0.4mm Finish/Colour: Lining Enamel, colour White. Core insulation: Zero ODP and LPCB certified. Panel thickness: 155mm overall (90mm core) End laps: 200mm. End lap sealant: Single line of 50mm x 3mm co-laminate PVC/low temperature butyl rubber sealant, Ref: KZ2, site applied at lap in external facings. Single line of non-setting gun-grade, Scapa Tapes Ref: 0100 or similar, site applied at lap in external facings. Side lap sealant: Anti-condensation tape, factory applied at butt joint between panels. Fasteners: As determined by Clause 220C. Number and location: Primary fasteners: As determined by Clause 197A, but with each panel fixed to every support using stainless steel halter clip, Ref: KS1-90, located through the side of the panel with a minimum two fasteners per halter per support as recommended by cladding manufacturer. Secondary fasteners: Stitch external end laps using five fastenings per panel, located 35mm upslope from end lap, penetrating factory applied stitching plate on underside of down slope panel. 17 Ref No: 1/5.13/LPS-B Accessories: Profiled fillers as Clause 300A. Ridge shroud Ref: KZ4-500A or KZ4-1000A as Cause 310A. Ridge flashing and profiled fillers to be supported using zed support Ref: KZ10A as Clause 310A. Eaves below 4 - Profiled filler, Ref: KZ and closure flashing Ref: KZ19A. Thermal Transmittance (U Value) calculated using the method required by the Building Regulations Part L2 (England & Wales) and Building Standards Part J (Scotland): 0.25 W/m2K. This will comply with Building Regulations Irish Building Regulations for Ireland. Air leakage rate of 10m3/hr/m2 at 50 Pa. Other requirements: Internal face of panel to be air sealed along the full length by an unbroken run of 6mm diameter butyl rubber sealant tape, class A, Ref: TB36. Side joint to be hand seamed at ridge, eaves and end laps prior to power seaming in both directions immediately after panel is fastened to purlins. For roof pitches below 4 - turn up and turn down using cladding manufacturers supplied tool at ridge and eaves respectively. Cladding contractor to be given installation training at Kingspan. 185A Performance Compliance Verification: The system has independent accreditation for the long-term thermal performance, structural performance, air leakage, weathertightness, condensation risk and durability. Verifying authority: British Board of Agrément. Certificate number 04/4181 dated: 15th December A - Attachment Determine the number and location of cladding fasteners recommended by the cladding manufacturer to resist wind loads calculated in accordance with BS 6399: Part 2 Standard Method and BS 5427: Part 1. Calculate wind loads on roof and wall cladding appropriate to location, exposure, roof height, building shape and size in accordance with BS 6399: Part 2 Standard Method and BS 5427: Part 1. Basic wind speed (Vb): m/s Altitude factor (Sa): Direction factor (Sd): Seasonal factor (Ss): 1 Probability factor (Sp): 1 Terrain and building factor (Sb): External and internal size effect factors (Ca): 1 External pressure coefficients (Cpe): As determined from BS 6399: Part 2, Clauses 2.4 and 2.5. Internal pressure coefficients (Cpi): As determined from BS 6399: Part 2, Clause 2.6. Dominant opening: Model Specifications

2 KS500/1000 ZIP/Zero ODP/LPCB Standing Seam Roof System Standard External and Internal Environments Aluminium External / Steel Liner - LPS Grade EXT-B 220C - Fasteners Recommended Manufacturers: UK SFS Intec Limited, tel: EJOT UK Limited, tel: Mage Fasteners Limited, tel: Ash & Lacy Building Systems Limited, tel: Ireland SFS Intec Ltd, tel: EJOT Ecofast Ltd, tel: Mage Fasteners Limited, tel: Halter fasteners: Self drilling, self tapping screws. Type(s), size(s) and drilling capacity: As recommended by fastener manufacturer to suit type and thickness of supports, and thickness of cladding panels. Screw material: Grade 304 austenitic stainless steel. Washer material: Grade 304 austenitic stainless steel. Heads: Not coloured End lap stitchers: Self drilling, self tapping screws with bonded washers. Screw material: As primary fasteners. Secondary fasteners: Stitching screws with bonded washers. Screw/washer material: As primary fasteners. Washer size: 19mm diameter. Heads: Coloured plastic heads. Flashing fasteners: Stitching screws with bonded washers. Screw/washer material: As primary fasteners. Washer size: 14mm diameter. Heads: Low profiled heads to match colour of the flashing Prevention of Electrolytic Action Isolating tape: PVC Location: To contact surfaces of supports and sheets of dissimilar metals Continuity Thermal Insulation Junctions between the roof panel system and walls/penetrations insulated with PIR board insulation any gaps filled with Alfasbond FR or similar fire rated gun applied canister urethane insulation. Placement: Secure and continuous with cladding/covering insulation. Ref No: 1/5.13/LPS-B 310A - Purpose Made Cold Formed Metal Accessories - External Drawing reference(s): Material/finish: As external face of cladding. Thickness: 0.9mm Colour: To match external face of cladding. Workmanship as section Z11. Fixing: Stitch to external face of panels at 400mm centres using secondary fasteners as specified for the cladding system. Only one flashing end to be stitched to butt strap and a 3mm gap should be left between flashing ends. Sealing: Single line of 20mm wide x 3mm thick butyl rubber sealant tape, class A, Ref: TB36, site applied between flashing and panel. 311A - Purpose Made Cold Formed Metal Accessories - Internal Drawing reference(s): Material/finish: As internal face of cladding. Thickness: 0.4 mm Colour: White. Workmanship as section Z11. Fixing: Stitch to internal face of panels at 450mm centres using secondary fasteners as specified for the cladding system. Sealing: Single line of 6mm diameter butyl rubber sealant, class A, Ref: TB36, site applied between flashing and panel. End laps to be air sealed with Vapourflex or similar or noncuring mastic, Scapa Tapes, Ref: 0100 or similar. 300A - Profiled Fillers Drawing reference(s): Manufacturer and reference: Premier Sealant Systems Limited Ref: E25 or similar, type to suit cladding profile. Material: EPDM foam. Colour: Black. Fixing: Seal the top, bottom and sides of each profiled filler with a single line of non-setting gun-grade, Scapa Tapes, Ref: 0100 or similar. Locate where shown on drawings and wherever necessary to close off corrugation cavities from the inside and outside of the building. Ensure a tight fit and leave no gaps. 18

3 KS500/1000 ZIP/Zero ODP/LPCB Standing Seam Roof System Standard External and Internal Environments Aluminium External / Steel Liner - LPS Grade EXT-B Detail 1 - Side Lap Detail 2 - End Lap Ref No: 1/5.13/LPS-B 200mm end lap Halter Factory applied anticondensation seal 35mm Halter Tail stitcher Gun-grade sealant 50mm x 3mm co-laminate end lap sealant Gun-grade sealant Halter fasteners Factory fitted plate Detail 3 - Fastener Locations Note: For curved end lap details contact Kingspan Technical Design Bureau. Model Specifications Detail 4 - Ridge Detail Halter at side joint Shroud over profiled filler With roof slopes below 4º Ridge panels must be turned up on site prior to fitting Ridge flashing 75 mm 66 mm Air seal - 8mm Ø butyl rubber sealant Site applied Alfasbond or similar fire rated (FR) canister insulation EPDM ridge filler Air seal - 8mm Ø butyl rubber sealant Liner flashing with 150mm end-laps and sealed *Note: For construction details for Ireland please contact Kingspan Technical Services Department on

4 20

5 EJOT Fasteners Product: Aluminium - KS500/1000 ZIP Standing Seam Roof System Core Austenitic Stainless Steel Fasteners Purlin Thickness (All Building Classifications) Frequency Per Clip Type & Thickness (mm) Hexagonal Head KS500 ZIP KS1000 ZIP Cold Rolled 90 JT x mm Hot Rolled 90 JT x mm Timber 90 JT x80 2 2* *Only 2 fasteners can be used into timber and the working pullout value of the fastener from timber may dictate the span of the panel rather than the load-span table. The cladding contractor should check this with the fastener supplier. A safety factor of 3 should be used to give the working load of fasteners from timber. End lap stitching fasteners Stitcher fasteners for steel flashings, shrouds etc Stitcher fasteners for aluminium flashings, shrouds etc JT3-FR6 5.5x35 S19 5 per end lap 10 per end lap JT3-FR-2H 4.8x19 S14 JT3-FR-2H 6.3x25 S16 SFS Intec Fasteners Product: Aluminium - KS500/1000 ZIP Standing Seam Roof System Purlin Type & Thickness Core Austenitic Stainless Steel Fasteners Thickness (All Building Classifications) Frequency Per Clip (mm) Hexagonal Head KS500 ZIP KS1000 ZIP Cold Rolled 90 SX5/18-5,5x38 Less than 1.8mm = 3 Less than 1.8mm = mm Over 1.8mm = 2 Over 1.8mm = 3 Fastener Selection Hot Rolled 90 SX14/38-5,5x mm Timber 90 TDA-S-6,5x76 2 2* Pre-drill 4mm pilot hole in panel/timber *Only 2 fasteners can be used into timber and the working pullout value of the fastener from timber may dictate the span of the panel rather than the load-span table. The cladding contractor should check this with the fastener supplier. A safety factor of 3 should be used to give the working load of fasteners from timber. End lap stitching fasteners Stitcher fasteners for steel and aluminium flashings, shrouds etc SXL2-L12-A14-5,5x22 (x colour) SX3/15-L12-S19-5.5x38 5 per end lap 10 per end lap Irius head (powder coated where applicable) 21

6 MAGE Fasteners Product: Aluminium - KS500/1000 ZIP Standing Seam Roof System Purlin Type & Thickness Core Austenitic Stainless Steel Fasteners Thickness (All Building Classifications) Frequency Per Clip (mm) Hexagonal Head KS500 ZIP KS1000 ZIP Cold Rolled /63/047/E mm Cold Rolled /63/047/E mm Hot Rolled /55/062/E mm Timber /55/070/E 2 2* *Only 2 fasteners can be used into timber and the working pullout value of the fastener from timber may dictate the span of the panel rather than the load-span table. The contractor should check this with the fastener supplier. A safety factor of 3 should be used to give the working load of fasteners from timber. End lap stitching fasteners Stitcher fasteners for steel flashings, shrouds etc Stitcher fasteners for aluminium flashings, shrouds etc 7110/55/038/E/S19 5 per end lap 10 per end lap 7140/48/020/E/R /63/022/E/R10 The load span tables for the Kingzip insulated standing seam roof panel system are generally dictated by the structural performance of the halters which have a working load of 1) 3.1kN for the KS500 Kingzip panel and 2) 5.1kN for the KS1000 Kingzip panel. The fastener quantities above are minimum and are to be used as broad guidelines only. With the Kingzip panel, (as with any other panel), design suction loads on the roof cladding should be calculated and issued by the Project Engineer. The uplift load can then be calculated for the purlin spacing and applied to the individual halter. This calculation will give the required quantity of fasteners per halter. The design suction loads to local areas of roof such as verges, ridge and eaves can be considerably more than general areas and must also be checked against the fastener arrangement. Individual fastener performance values can be obtained from the fastener supplier. Note that when talking directly to a fastener supplier a customer should be aware that the supplier may/will be talking about a fastener s ultimate structural characteristic performance and not the working load which will be half of the ultimate as recommended in BS 5427: Part 1: 1996 Annex B. Thinner purlins may mean lower fastener pull-out values from the purlins under wind uplift. This may then require the use of additional fasteners. The fastener pull-out values could actually dictate closer purlin spacings than usual. With purlins of thickness less than 1.5mm, please contact the Kingspan Technical Design Bureau at the earliest opportunity. Note that there will be instances where an alternative fastener or pre-drilling will be required, for example, where a gutter wing rests over a purlin. Please contact the fastener supplier for advice. Contact for further advice: Kingspan Technical Design Bureau on UK Tel: , Fax: , Ireland Tel: , Fax:

7 Fastener Selection 23

8 Side & End Lap Details Side Lap Detail Factory applied anti-condensation seal Halter fasteners: KS500 ZIP 2 fasteners KS1000 ZIP 3 fasteners (minimum) KS500 ZIP End Lap - Fastener Locations 500mm cover width Locations for end lap screws through end lap into stitching plate 200mm end lap KS500 Halter KS500 Halter 35mm Tail stitcher Gun-grade sealant 50mm x 3mm co-laminate end lap sealant Gun-grade sealant Factory fitted plate *Note: For construction details for Ireland please contact Kingspan Technical Services Department on

9 End Lap Details KS1000 ZIP End Lap - Fastener Locations 1000mm cover width 500mm KS1000 ZIP End Lap Detail KS1000 Halter Note: KS1000 halter only used at intermediate purlin positions. Use KS500 halter at eaves, ridge hips etc. 35mm 200mm end lap KS1000 Halter Tail stitcher Gun-grade sealant 50mm x 3mm co-laminate end lap sealant Gun-grade sealant Factory fitted plate Ridge Detail Halter at side joint # Shroud over profiled filler. Shroud stitched to each panel with sealed stitching screws With roof slopes below 4º ridge panels must be turned up on site prior to fitting Ridge flashing stitched to max 400mm c/cs and bed on 20mm x 3mm butyl rubber sealant 75 mm 66 mm Air seal - 8mm bead of gun-grade sealant, Scapa Tapes Ref: 0100 or similar Site applied Alfasbond or similar fire rated (FR) canister insulation EPDM ridge filler: KZ3-500 for 500 wide panel KZ for 1000 wide panel bed in 5mm (generous) bead of Scapa Tapes, Ref: 0100 or similar non-curing mastic ensuring no visible gaps between panel profile and filler Air seal - 8mm bead of gun-grade sealant, Scapa Tapes Ref: 0100 or similar Liner flashing with 150mm end-laps and sealed Construction Details *Note: For construction details for Ireland please contact Kingspan Technical Services Department on

10 Eaves Details * External Gutter 20 x 3mm butyl rubber sealant under gutter support 600mm long gutter support arm fixed over panel crown and also to middle of panel cover width with KS1000 ZIP 100mm Site applied Alfasbond or similar fire rated (FR) canister insulation Top sheet turned down on site with roof pitch below 4 Joint filler bed in Scapa Tapes 0100 or similar grade non-curing mastic Air seal - 8mm bead of gun-grade sealant, Scapa Tapes Ref: 0100 or similar Air seal - 6mm Ø bead of gun-grade sealant Liner side joint locally sealed with Scapa Tapes 0100 or similar grade non-curing mastic 35 mm Eaves beam KS1000 MR/LPCB horizontally laid Building Regulations Part L2 Thermal Data fmin = 0.95 Ψ = 0.13 W/mK The above values are only applicable to the components on this detail. Changes to the components will have an effect on the given values. Parapet Detail - Boundary Wall Gutter PIR insulation board Parapet flashing with 150mm sealed butt straps Site applied Alfasbond or similar fire rated (FR) canister insulation AWP filler bed in Scapa Tapes 0100 or similar grade non-curing mastic Air seal - 6mm Ø nominal gun-grade sealant KS1000 MR/LPCB vertically laid Air seal - 6mm Ø nominal gun-grade sealant KZ12-90 EPDM joint filler to suit KS500/1000 ZIP 90mm panel at eaves/gutter KS1000 MR/LPCB horizontally laid 100mm Liner side joint locally sealed with Scapa Tapes 0100 or similar grade non-curing mastic 60mm 2mm external non-thermally broken factory made gutter with PIR insulation to 0.25 or 0.35 W/m 2 K U-value Halter at side joint Building Regulations Part L2 Thermal Data 0.25 W/m 2 K gutter fmin = 0.74 Ψ = 1.33 W/mK 0.35 W/m 2 K gutter fmin = 0.71 Ψ = 1.18 W/mK 0.35 sole width 300mm and depth 150mm, values for other widths available on request. The above values are only applicable to the components on this detail. Changes to the components will have an effect on the given values. Air seal - 8mm bead of gungrade sealant, Scapa Tapes Ref: 0100 or similar *Note: For construction details for Ireland please contact Kingspan Technical Services Department on

11 Verge Details Verge Detail - Start PIR board insulation with Alfasbond or similar fire rated (FR) canister applied insulation to fill any gaps if required to maintain continuity of insulation Verge flashing with 150mm sealed butt straps Note: for aluminium flashings allow for expansion/movement # Flashing max unstiffened leg width 250mm Direction of lay 75mm Fix flashings at max 400mm centres 20 x 3mm butyl rubber sealant Air seal - 8mm bead of gun-grade sealant, Scapa 0100 or similar KS1000 ZIP insulated roof panel Air seal - 6mm Ø butyl rubber sealant 4mm Ø butyl rubber sealant Purlin KS1000 MR/LPCB horizontally laid Cleader angle by steel sub-contractor with air seal Vapourflex or similar sealant applied at joints Building Regulations Part L2 Thermal Data fmin = 0.96 Ψ = 0.01 W/mK The above values are only applicable to the components on this detail. Changes to the components will have an effect on the given values. Verge Detail - End Direction of lay Fix flashings at max 400mm centres 20 x 3mm butyl rubber sealant Air seal - 8mm bead of gun-grade sealant, Scapa Tapes Ref: 0100 or similar KS1000 ZIP insulated roof panel 20 x 3mm butyl rubber sealant PIR board insulation with Alfasbond or similar fire rated (FR) canister applied insulation to fill any gaps if required to maintain continuity of insulation Verge flashing with 150mm sealed butt straps Note: for aluminium flashings allow for expansion/movement. # Flashing max unstiffened leg width 250mm Air seal - 6mm Ø bead of gun-grade sealant Purlin Cleader angle by steel sub-contractor with air seal Vapourflex or similar sealant applied at joints 4mm Ø butyl rubber sealant Construction Details Building Regulations Part L2 Thermal Data fmin = 0.97 Ψ = 0.01 W/mK The above values are only applicable to the components on this detail. Changes to the components will have an effect on the given values. KS1000 MR/LPCB horizontally laid *Note: For construction details for Ireland please contact Kingspan Technical Services Department on

12 Curved Roof Details For Coated Steel Curved Roof Panel Layout Sequence Panel length (L) Ridge panel with end lap at each panel end Downslope Upslope Panel 2 (Crown) Lap angle minimum 1.5 after deflections Panel 1 (Eaves) Panel 3 (Eaves) Building width of between 70m to 100m approx. Minimum 150m radius (R) KS500 Curved Roof - End Lap Detail Generous (approx 5mm Ø bead) gun application on site of Scapa Tapes, Ref: 0100 or similar non-curing sealant to rounded part of upstand ensuring the bead meets the KZ2 seal 200mm end lap 35mm 10mm 10mm Generous (approx 5mm Ø bead) gun application on site of Scapa Tapes, Ref: 0100 or similar non-curing sealant to rounded part of upstand ensuring the bead meets the KZ2 seal Halter at side joint Kingspan KZ2 50 x 3mm co-laminate PVC/low temperature butyl end-lap seal, site applied, ensuring seal is pushed into all profiles (with grey PVC face-up). Seal taken up upstands and stopped at round part of keyhole profile Low profile headed fastener with 19mm Ø stainless steel washer. Fastener to be stainless steel for aluminium panels/coastal or extended warranty requirements. Thread type to suit end lap plate. One fixing per trough i.e 5 fixings per panel end lap 10 x 150 x 10 x 1.6mm thick galvanised steel extension channel to give greater bearing for curved roof end lap tolerances accumulation Nominal bearing top panel 50mm Temporary Fix Rivet or Flat Head Fastener Factory fitted end lap plate KS1000 Curved Roof - End Lap Detail Generous (approx 5mm Ø bead) gun application on site of Scapa Tapes, Ref: 0100 or similar non-curing sealant to rounded part of upstand ensuring the bead meets the KZ2 seal 200mm end lap 35mm 10mm 10mm Generous (approx 5mm Ø bead) gun application on site of Scapa Tapes, Ref: 0100 or similar non-curing sealant to rounded part of upstand ensuring the bead meets the KZ2 seal Halter at side joint Kingspan KZ2 50 x 3mm co-laminate PVC/low temperature butyl end lap seal, site applied, ensuring seal is pushed into all profiles (with grey PVC face-up). Seal taken up upstands and stopped at round part of keyhole profile Low profile headed fastener with 19mm Ø stainless steel washer. Fastener to be stainless steel for aluminium panels/coastal or extended warranty requirements. Thread type to suit end lap plate. One fixing per trough i.e 10 fixings per end lap 10 x 150 x 10 x 1.6mm thick galvanised steel extension channel to give greater bearing for curved roof tolerances accumulation Nominal bearing top panel 50mm Temporary Fix Rivet or Flat Head Fastener Factory fitted end lap plate *Note: For construction details for Ireland please contact Kingspan Technical Services Department on

13 Construction Details 29

14 Eaves Seam Starter Tool Roof Penetrations Penetrations and junctions as well as architectural features can be dealt with by the following alternative measures dependant upon desired aesthetic finish as well as budget. Site Welding On-site TIG welding of aluminium Kingzip end laps, upstands, soil vent pipe penetrations, hips, hip valleys and other features can be carried out by the following experienced companies. It is always necessary with standing seam systems to consider the design, logistics, co-ordination and cost of penetrations/features at an early stage. Early contact with a recommended company by the designer and subsequent cladding installation contractor is necessary to ensure the project proceeds smoothly, safely and to budget, and to ensure co-ordination with other trades. Sureweld & Roof Ltd Ball Mill Top, Hallow, Worcester WR2 6LS Tel: , Fax: sales@sureweld.org Contact: Darren Powell, Director Profix Roofing Systems Ltd Reginald Road Industrial Estate Unit 4-5 Brindley Road, Sutton St. Helens Merseyside WA9 4HY Tel: , Fax: @profixroofing.fsnet.co.uk Contact: Andy Allanson, Director Power Seamer Site Installed Soakers The following companies can provide colour coated soakers, upstands, sleeves flashings and features with proven long term weathering performance and to suit aluminium or coated steel Kingzip insulated standing seam panels. Again, early contact with a recommended company by the designer and subsequent cladding installation contractor is necessary to ensure the project proceeds smoothly, safely and to budget, and to ensure co-ordination with other trades. "Aperture PU or Aperture 185 Seamless Cold Applied Systems" from:- Aperture Unit 0, Springfield Trading Estate, Samuel Street, Failsworth, Manchester M35 OGA Tel: , Fax: enquiries@aperturesp.co.uk Contact: Michael Philbin, Operations Manager "GRP System of Standard and Purpose Made Weathering" from:- Jones & Woolman (UK) Ltd Croxtalls Road, Bloxwich, Walsall, West Midlands WS3 2XU Tel: , Fax: jwuk@btinternet.com Contact: Darren Jones, Sales Director Tool Hire from:- Blue Sky Access Ltd PO Box 4686 Henley on Thames, Oxfordshire, RG9 2ZS UK - Tel: , Fax: rkyte@ukonline.co.uk Contact: Richard Kyte MAK Fasteners Ireland Contact: Michael McDonald Jr Installation contractor training and information is available through our Field Services Department UK - Tel: Ireland- Tel:

15 31 Site Installation Methods

16 Kingspan Insulated Roof, Wall & Facade Systems Roof Systems KS1000 RW Trapezoidal KS1000 SF Secret Fix KS1000 TS Tile Support KS500/1000 ZIP KingZIP KS1000 LP Lo-pitch KS1000 CR Curved KS1000 RT Roof Tile KS1000 XD X-dek LongSpan Wall & Facade Systems KS600, 900 & 1000 Optimo KS600, 900 & 1000 MR Micro-Rib KS600, 900 & 1000 EB Euro-Box KS600, 900 & 1000 FL-S Flat (Stucco) KS1000 Thermatile Tile Hanging System KS600, 900 & 1000 MM Mini-Micro KS600, 900 & 1000 CX Convex KS600, 900 & 1000 WV Wave KS600, 900 & 1000 LS LongSpan KS1000 RW Trapezoidal Kingspan Limited UK: Telephone: +44 (0) Fax: +44 (0) Ireland: Telephone: +353 (0) Fax: +353 (0) Details for the following countries; Australia, Belgium, China, Czech Republic, Germany, Hungary, Netherlands, Poland, Singapore can be found by visiting our website or our group website