900 SERIES WALL PANELS

Size: px

Start display at page:

Download "900 SERIES WALL PANELS"

Ellen Robbins
6 years ago
Views:

1 CI-DS CI-PP CI-PJ CI-PJ CI-PJ CI-BS CI-BS CI-BS CI-BS CI-BS CI-OC CI-OC CI-IC CI-FO CI-FO CI-FO CI-FO CI-FO CI-FO CI-SJ CI-SJ CI-PR CI-PR CI-LE CI-RK CI-HE CI-TL CI-TL CI-TL CI-TL C & I DISCLAIMER 900 SERIES PANEL PROFILE 900 EXPANDED PANEL JOINT 900 ENGAGED PANEL JOINT INTERMEDIATE SUPPORT BASE DETAIL - FLUSH BASE DETAIL - NOTCHED CONCRETE BASE DETAIL - OVERHANG W/ SUPPORT BASE DETAIL - OVERHANG W/ ANGLE BASE DETAIL - OVERHANG W/ DRIP OUTSIDE CORNER WITH FLAT TRIM OUTSIDE CORNER WITH MITER CUT INSIDE CORNER WITH FLAT TRIM F.O. HEAD WITH DRIP EDGE F.O. TWO PIECE JAMB F.O. ONE PIECE JAMB F.O. ONE PIECE SILL O.H. DOOR HEAD WITH DRIP EDGE O.H. DOOR TWO PIECE JAMB STACK JOINT WITH FLUSH TRIM STACK JOINT WITH PROFILED TRIM PARAPET WITH FLUSH TRIM PARAPET WITH PROFILED TRIM LOW EAVE W/ GUTTER RAKE HIGH EAVE TRIM END LAP TRIM END LAP WITH HEM TRIM END LAP WITH LAP STRIP TRIM LAP AT F.O. INDEX SHEET

2 DISCLAIMER: THESE DETAILS ARE PROVIDED AS A GUIDELINE FOR PROPER PANEL AND ASSOCIATED COMPONENT INSTALLATION, AND ARE BASED ON INDUSTRY ACCEPTED PRACTICES. LOCATION OF VAPOR BARRIERS AND ASSOCIATED SEALANTS IN THESE DETAILS ARE BASED ON TYPICAL DESIGN PRACTICES FOR MOST U.S. CLIMACTIC ZONES. (THE PRIMARY VAPOR BARRIER IS PLACED ON THE "WARM" SIDE IN WINTER). PROJECTS LOCATED IN AREAS SUBJECT TO EXTREME COLD AND/OR HIGH SNOW LOADS MAY REQUIRE MODIFICATIONS TO THESE DETAILS - CONTACT KINGSPAN TECHNICAL SERVICES FOR SPECIFIC PROJECT RECOMMENDATIONS. COMMERCIAL/INDUSTRIAL DISCLAIMER

3 CORE DEPTHS: 1.5", 2", 2.5", 3", 4", 5", 6" STEEL GAUGES: EXTERIOR: 22, 24 INTERIOR: 26, 24, 22 MODULE WIDTH: " (39 3 8") PANEL ORIENTATION: VERTICAL APPLICATION ONLY EMBOSSING: EXTERIOR: STUCCO / SMOOTH INTERIOR: STUCCO / SMOOTH LENGTHS: MINIMUM: 8'-0" MAXIMUM: 53'-0" " (1000mm) HIGH RIB PROFILE EXTERIOR INTERIOR 1 1 2" 1 1 2" - 6" V-GROOVE PROFILE 900 SERIES PANEL PROFILE

4 1 4 " - 14 STITCH TEK (HEX HEAD OR LOW 24" O.C. ALONG OVERLAP (MAX. 4" FROM PANEL ENDS) 1 4 " - 14 THROUGH FASTENERS W/ WASHER (AS REQUIRED FOR WIND LOAD) 1 4 " - 14 STITCH TEK SCREW (HEX HEAD OR LOW 24" O.C. ALONG OVERLAP (MAX. 4" FROM PANEL ENDS) FIELD APPLIED BUTYL TAPE ENTIRE LENGTH OF OVERLAP 1 4 " - 14 THROUGH FASTENERS W/ WASHER (AS REQUIRED FOR WIND LOAD) FIELD APPLIED CONTINUOUS BUTYL SEALANT WALL PANEL INSTALLATION DIRECTION 900 EXPANDED PANEL JOINT

5 1 4 " - 14 STITCH TEK (HEX HEAD OR LOW 24" O.C. ALONG OVERLAP (MAX. 4" FROM PANEL ENDS) 1 4 " - 14 THROUGH FASTENERS W/ WASHER (AS REQUIRED FOR WIND LOAD) 1 4 " - 14 THROUGH FASTENERS W/ WASHER (AS REQUIRED FOR WIND LOAD) 1 4 " - 14 STITCH TEK SCREW (HEX HEAD OR LOW 24" O.C. ALONG OVERLAP (MAX. 4" FROM PANEL ENDS) FIELD APPLIED BUTYL TAPE ENTIRE LENGTH OF OVERLAP FIELD APPLIED CONTINUOUS BUTYL SEALANT WALL PANEL INSTALLATION DIRECTION 900 ENGAGED PANEL JOINT

6 SEALANT AT PANEL JOINT 1 4 " - 14 THROUGH FASTENERS W/ WASHER (AS REQUIRED FOR WIND LOAD) HORZONTAL SUPPORT INTERMEDIATE SUPPORT

7 1 4 " - 14 STITCH TEK (HEX HEAD OR LOW 24" O.C. ALONG OVERLAP (MAX. 4" FROM PANEL ENDS) SEALANT AT PANEL JOINT 1 4 " - 14 THROUGH FASTENER W/ WASHER (AS REQUIRED FOR WIND LOAD) SEALANT BASE TRIM BASE FLASHING BASE ANGLE W/ MIN. 3" VERT. LEG FOR PANEL ATTACHMENT SEALANT BELOW BASE FLASHING FASTENER TO CONCRETE SEALANT MARRIAGE BEAD TO VERTICAL PANEL JOINT NOTE: SEE DETAIL CI-TL AND CI-TL FOR TYPICAL TRIM LAP INSTRUCTIONS BASE DETAIL - FLUSH

8 1 4 " - 14 STITCH TEK (HEX HEAD OR LOW 24" O.C. ALONG OVERLAP (MAX. 4" FROM PANEL ENDS) BASE TRIM SEALANT AT PANEL JOINT 1 4 " - 14 THROUGH FASTENERS W/ WASHER (AS REQUIRED FOR WIND LOAD) SEALANT W/ MARRIAGE BEAD TO VERTICAL PANEL JOINT BASE ANGLE W/ MIN. 3" VERT. LEG FOR PANEL ATTACHMENT BASE FLASHING " (TYP.) FASTENER TO CONCRETE SEALANT BELOW BASE FLASHING NOTE: SEE DETAIL CI-TL AND CI-TL FOR TYPICAL TRIM LAP INSTRUCTIONS BASE DETAIL - NOTCHED CONCRETE

9 1 4 " - 14 STITCH TEK (HEX HEAD OR LOW 24" O.C. ALONG OVERLAP (MAX. 4" FROM PANEL ENDS) BASE TRIM SEALANT AT PANEL JOINT 1 4 " - 14 "LOW PROFILE" THROUGH FASTENER (AS REQUIRED FOR WIND LOAD) SEALANT W/ MARRIAGE BEAD TO VERTICAL PANEL JOINT BASE ANGLE W/ MIN. 3" VERT. LEG FOR PANEL ATTACHMENT " (TYP.) SEALANT FASTENER TO CONCRETE NOTE: SEE DETAIL CI-TL AND CI-TL FOR TYPICAL TRIM LAP INSTRUCTIONS BASE DETAIL - OVERHANG W/ SUPPORT

10 1 4 " - 14 STITCH TEK (HEX HEAD OR LOW 24" O.C. ALONG OVERLAP (MAX. 4" FROM PANEL ENDS) BASE TRIM SEALANT AT PANEL JOINT 1 4 " - 14 "LOW PROFILE" THROUGH FASTENER (AS REQUIRED FOR WIND LOAD) SEALANT W/ MARRIAGE BEAD TO VERTICAL PANEL JOINT BASE ANGLE W/ MIN. 3" VERT. LEG FOR PANEL ATTACHMENT " (TYP.) SEALANT FASTENER TO CONCRETE NOTE: SEE DETAIL CI-TL AND CI-TL FOR TYPICAL TRIM LAP INSTRUCTIONS BASE DETAIL - OVERHANG W/ ANGLE

11 1 4 " - 14 STITCH TEK (HEX HEAD OR LOW 24" O.C. ALONG OVERLAP (MAX. 4" FROM PANEL ENDS) BASE TRIM SEALANT AT PANEL JOINT 1 4 " - 14 "LOW PROFILE" THROUGH FASTENER (AS REQUIRED FOR WIND LOAD) SEALANT W/ MARRIAGE BEAD TO VERTICAL PANEL JOINT BASE ANGLE W/ MIN. 3" VERT. LEG FOR PANEL ATTACHMENT " (TYP.) SEALANT BASE TRIM FASTENER TO CONCRETE SEALANT NOTE: SEE DETAIL CI-TL AND CI-TL FOR TYPICAL TRIM LAP INSTRUCTIONS BASE DETAIL - OVERHANG W/ DRIP

12 WILL VARY WITH FIELD CONDITION WILL VARY WITH FIELD CONDITION FIELD CUT OUTSIDE CORNER TRIM F.I.P. INSULATION AS REQUIRED (BY OTHERS) 3 4 " PHIL. PAN HEAD CONTINUOUS BUTYL SEALANT 1 4 " - 14 THROUGH FASTENERS W/ 1 1 8" WASHER (AS REQUIRED FOR WIND LOAD) ATTACHMENT CLIP (BY OTHERS) CONTINUOUS BUTYL SEALANT HORIZONTAL SUPPORT OUTSIDE CORNER WITH PROFILED TRIM

13 WILL VARY WITH FIELD CONDITION WILL VARY WITH FIELD CONDITION FIELD CUT OUTSIDE CORNER TRIM F.I.P. INSULATION AS REQUIRED (BY OTHERS) 1 4 " - 14 "LOW PROFILE" THROUGH FASTENERS W/ 1 1 8" WASHER (AS REQUIRED FOR WIND LOAD) 3 4 " PHIL. PAN HEAD CONTINUOUS BUTYL SEALANT ATTACHMENT CLIP (BY OTHERS) CONTINUOUS BUTYL SEALANT HORIZONTAL SUPPORT OUTSIDE CORNER WITH FLAT TRIM

14 WILL VARY WITH FIELD CONDITION WILL VARY WITH FIELD CONDITION FIELD CUT SEALANT CONTINUOUS SEALANT APPLIED AT FASTENER LOCATIONS OUTSIDE CORNER TRIM F.I.P. INSULATION AS REQUIRED (BY OTHERS) HORIZONTAL SUPPORT SEALANT 3 4 " PHIL. PAN HEAD 8" O.C. INSIDE CORNER TRIM 1 4 " - 14 THROUGH FASTENERS W/ 1 1 8" BONDED WASHER (AS REQUIRED FOR WIND LOAD) INSIDE CORNER WITH PROFILED TRIM

15 SEALANT AT PANEL JOINT 1 4 " - 14 THROUGH FASTENER W/ WASHER SEALANT BOTH SIDES OF TRIM W/ MARRIAGE BEAD TO VERTICAL PANEL JOINT CONTINUOUS BUTYL SEALANT EXTERIOR CAP TRIM FRAMED OPENING DRIP FLASHING EXPOSED SEALANT DOOR/WINDOW FRAME, COMPONENTS AND ACCESSORIES NOTE: SEE DETAIL CI-TL AND CI-TL FOR TYPICAL TRIM LAP INSTRUCTIONS FRAMED OPENING HEAD W/ "DRIP EDGE"

16 FRAMED OPENING DOOR/WINDOW FRAME, COMPONENTS AND ACCESSORIES 1 4 " - 14 THROUGH FASTENER SEALANT BOTH SIDES OF TRIM INTERIOR CAP TRIM EXPOSED SEALANT EXTERIOR CAP TRIM NOTE: SEE DETAIL CI-TL AND CI-TL FOR TYPICAL TRIM LAP INSTRUCTIONS FRAMED OPENING TWO PIECE JAMB

17 FRAMED OPENING DOOR/WINDOW FRAME, ACCESSORIES AND WEATHER TIGHTNESS. FOLLOW COMPONENT MANUFACTURER INSTALLATION INSTRUCTIONS FOR PROPER INSTALLATION. FIELD BEND (AS REQUIRED) 1 4 " - 14 "LOW PROFILE" FASTENER (AS REQUIRED) 1 4 " - 14 THROUGH FASTENER SEALANT SEALANT EXPOSED SEALANT EXTERIOR CAP TRIM NOTE: SEE DETAIL CI-TL AND CI-TL FOR TYPICAL TRIM LAP INSTRUCTIONS FRAMED OPENING ONE PIECE JAMB

18 EXPOSED SEALANT SEALANT DOOR/WINDOW FRAME FIELD BEND (AS REQUIRED) SEALANT W/ MARRIAGE BEAD AT JOINT LOCATIONS EXTERIOR CAP TRIM 1 4 " - 14 "LOW PROFILE" FASTENER (AS REQUIRED) 1 4 " - 14 THROUGH FASTENER FRAMED OPENING SEALANT AT PANEL JOINT NOTE: SEE DETAIL CI-TL AND CI-TL FOR TYPICAL TRIM LAP INSTRUCTIONS FRAMED OPENING ONE PIECE SILL

19 SEALANT AT PANEL JOINT SEALANT BOTH SIDES OF TRIM W/ MARRIAGE BEAD TO VERTICAL PANEL JOINT 1 4 " - 14 THROUGH FASTENER 3 EXTERIOR CAP TRIM FRAMED OPENING 2 DRIP FLASHING EXPOSED SEALANT 1 FASTENER HEADER TRIM (OPTIONAL) TRIM INSTALLATION SEQUENCE: 1 INSTALL HEADER TRIM (OPTIONAL) & ALL APPLICABLE SEALANTS 2 INSTALL DRIP FLASHING & ALL APPLICABLE SEALANTS PRIOR TO INSTALLING THE PANEL AND THROUGH FASTENERS 3 INSTALL EXTERIOR CAP TRIM NOTE: SEE DETAIL CI-TL AND CI-TL FOR TYPICAL TRIM LAP INSTRUCTIONS OVERHEAD DOOR HEAD W/ DRIP EDGE

20 FASTENER FRAMED OPENING 1 4 " - 14 THROUGH FASTENER 1 JAMB TRIM (OPTIONAL) SEALANT 2 INTERIOR CAP TRIM EXPOSED SEALANT 3 EXTERIOR CAP TRIM TRIM INSTALLATION SEQUENCE: 1 INSTALL JAMB TRIM (OPTIONAL) & ALL APPLICABLE SEALANTS 2 INSTALL INTERIOR CAP TRIM & ALL APPLICABLE SEALANTS PRIOR TO INSTALLING THE PANEL AND THROUGH FASTENERS 3 INSTALL EXTERIOR CAP TRIM NOTE: SEE DETAIL CI-TL AND CI-TL FOR TYPICAL TRIM LAP INSTRUCTIONS OVERHEAD DOOR TWO-PIECE JAMB

21 RIB CLOSURE TRIM STACK TRIM FIELD DRILL OPTIONAL 3 8" WEEP HOLES AS REQUIRED STACK FLASHING 1 4 " - 14 THROUGH FASTENER (AS REQUIRED FOR WIND LOAD) SEALANT W/ MARRIAGE BEAD TO VERTICAL PANEL JOINT HORIZONTAL SUPPORT FASTEN AS REQUIRED SEALANT W/ MARRIAGE BEAD AT PANEL JOINT LOCATIONS RIB CLOSURE TRIM CONTINUOUS 3" X 3" ANGLE (GAUGE TO MATCH GIRT) 1 4 " - 14 THROUGH FASTENER (AS REQUIRED FOR WIND LOAD) SEALANT AT PANEL JOINT STACK JOINT W/ FLUSH TRIM

22 RIB CLOSURE TRIM STACK TRIM 1 4 " - 14 THROUGH FASTENER (AS REQUIRED FOR WIND LOAD) SEALANT W/ MARRIAGE BEAD TO VERTICAL PANEL JOINT HORIZONTAL SUPPORT FASTEN AS REQUIRED STACK FLASHING SEALANT W/ MARRIAGE BEAD AT PANEL JOINT LOCATIONS RIB CLOSURE TRIM CONTINUOUS 3" X 3" ANGLE (GAUGE TO MATCH GIRT) 1 4 " - 14 THROUGH FASTENER (AS REQUIRED FOR WIND LOAD) SEALANT AT PANEL JOINT STACK JOINT W/ PROFILED TRIM

23 SEALANT W/ MARRIAGE BEAD AT JOINT LOCATIONS PARAPET BLOCKING PARAPET CAP WRAP MEMBRANE ADHERE TO EXTERIOR PANEL FACE FASTENER TO PARAPET BACKER 1 4 " - 14 THROUGH FASTENER (AS REQUIRED FOR WIND LOAD) 900 SERIES FOAM CLOSURE W/ BUTYL TAPE TOP AND BOTTOM SEALANT AT PANEL JOINT MEMBRANE ROOF & PARAPET BACKER PARAPET WITH FLUSH TRIM

24 SEALANT W/ MARRIAGE BEAD AT JOINT LOCATIONS PARAPET BLOCKING PARAPET CAP WRAP MEMBRANE ADHERE TO EXTERIOR PANEL FACE FASTENER TO PARAPET BACKER 1 4 " - 14 THROUGH FASTENER (AS REQUIRED FOR WIND LOAD) 900 SERIES FOAM CLOSURE W/ BUTYL TAPE TOP AND BOTTOM SEALANT AT PANEL JOINT MEMBRANE ROOF & PARAPET BACKER PARAPET WITH PROFILED TRIM

25 REFER TO 900/1000 SERIES ROOF PANEL DETAILS FOR ADDITIONAL INFORMATION EAVE STRUT SEALANT W/ MARRIAGE BEAD AT JOINT LOCATIONS 1 4 " - 14 THROUGH FASTENERS W/ WASHER (AS REQUIRED FOR WIND LOAD) SEALANT AT PANEL JOINT FASTENER 900 FOAM CLOSURE SET IN BUTYL TAPE TOP AND BOTTOM LOW EAVE W/ GUTTER

26 REFER TO 900/1000 SERIES ROOF PANEL DETAILS FOR ADDITIONAL INFORMATION SHEETING OR RAKE ANGLE REQUIRED SEALANT W/ MARRIAGE BEAD TO AT PANEL JOINT LOCATIONS FASTENER 900 FOAM CLOSURE SET IN BUTYL TAPE TOP AND BOTTOM 1 4 " - 14 THROUGH FASTENERS W/ WASHER (AS REQUIRED FOR WIND LOAD) SEALANT AT PANEL JOINT RAKE

27 REFER TO 900/1000 SERIES ROOF PANEL DETAILS FOR ADDITIONAL INFORMATION EAVE STRUT SEALANT W/ MARRIAGE BEAD AT PANEL JOINT LOCATIONS FASTENER 900 FOAM CLOSURE SET IN BUTYL TAPE TOP AND BOTTOM 1 4 " - 14 THROUGH FASTENERS W/ WASHER (AS REQUIRED FOR WIND LOAD) SEALANT AT PANEL JOINT RAKE

28 (2) BEADS BUTYL SEALANT MIN. 3" TRIM LAP MIN. 3" TRIM LAP TRIM END LAP

29 FIELD NOTCH HEM(S) AS REQUIRED MIN. 3" TRIM LAP (2) BEADS BUTYL SEALANT MIN. 3" TRIM LAP TRIM LAP WITH HEM

30 (2) BEADS BUTYL SEALANT 8" LONG LAP STRIP NOM. 1 4 " GAP TRIM END LAP WITH LAP STRIP

31 FIELD NOTCH AND OVERLAP TRIMS, POP RIVET AND SEAL AS NECESSARY SEALANT END DAM 2 INTERIOR HEAD TRIM WITH TABS BENT DOWN FIELD MITER AND OVERLAP TRIMS, POP RIVET AS NECESSARY INTERIOR CAP TRIM AT HEAD EXPOSED SEALANT EXTERIOR CAP TRIM AT HEAD 5 EXTERIOR HEAD TRIM W/ FIELD DRILL 3 8" Ø WEEP HOLES INTERIOR JAMB TRIM 1 SILL TRIM WITH TABS BENT UP 6 3 EXTERIOR CAP TRIM AT JAMB FIELD CUT/NOTCH CAP TRIM AT CORNERS TO ALLOW FOR LAP 4 EXTERIOR JAMB TRIM FIELD CUT/NOTCH CAP TRIM AT CORNERS TO ALLOW FOR LAP EXTERIOR CAP TRIM AT SILL FIELD MITER AND OVERLAP TRIMS, POP RIVET AND SEAL AS NECESSARY TRIM INSTALLATION SEQUENCE: 1 INTERIOR JAMB TRIM 2 INTERIOR HEAD TRIM WITH TABS DOWN 3 SILL TRIM WITH TABS UP 4 EXTERIOR JAMB TRIM 5 EXTERIOR HEAD TRIM 6 EXTERIOR SEALANTS AS REQUIRED TRIM LAP AT FRAMED OPENING

400 SERIES VERTICAL INSTALLATION

400 SERIES VERTICAL INSTALLATION CI-DS-01-400V CI-PJ-01-400V CI-PJ-02-400V CI-PJ-03-400V CI-BS-01-400V CI-BS-02-400V CI-BS-03-400V CI-BS-04-400V CI-BS-05-400V CI-OC-01-400V CI-OC-02-400V CI-IC-01-400V CI-IC-02-400V CI-FO-01-400V CI-FO-02-400V