June 2017 Greetings to Go. Pattern Play

Transcription

1 Assembly Line Cardmaking June 2017 Greetings to Go Pattern Play Pattern Play Materials: Greetings to Go Tools and Supplies: Scor-Pal Adhesive Tape Bone Folder CS Foam Adhesive Circles Paper Trimmer 3x14 CS Grid Ruler Preparation: Scissors Crop-a-dile or Eyelet Setter and Hole Punch Corner Rounder Punch or Corner Chomper Dry Embossing Folders and Embossing Machine (Optional) Daisy Punch (Optional) Sequins or Silver Round Dazzles (Optional) 1. Trim the three White printed cutaparts into sections as indicated by the artwork and cutting guidelines. (See page two for details.) 2. Scoring and folding information is listed within the instructions for each card set. TIP: The bump of the score goes on the inside of the fold. 3. If you do not have an item to complete the card as shown, simply omit or substitute the item. Watch this helpful video to learn important card assembly tips: To view more details about the cards, visit the following link: clubscrap.com/0617-layouts-cards All rights reserved. 2017, Club Scrap, Inc. (888)

2 June 2017 Pattern Play Greetings to Go Page 2 of 5 When trimming the White cutaparts according to the registration marks, sort each cutapart into three piles, one for each corresponding set of cards. Set A: 4¼x5½ Green Pop-up Cards with 4¼x8½ Green Mechanisms, 2¼x11 Gray Pop-up Panels and 1½x4¼ Dk. Gray Panels (when trimmed) 1. Trim the 4¼x6 Dk. Gray panel horizontally at 4½, 3 and 1½ to create four 1½x4¼ pieces, one for each card. 2. Score each 2¼x11 Gray panel horizontally at 2¾, 5½, and 8¼. Accordion fold. Alternatively, accordion fold the strip into four equally-sized panels. 3. Position the 4¼x8½ Green mechanism horizontally on your work surface. Place a CS Grid Ruler 2⅛ from the left edge of the paper. Fold the upper right corner of the paper downward, bringing the edge of the paper along the edge of the ruler, and crease to make a 45º angle. Open the fold. Without moving the ruler, bring the bottom right corner of the paper upward, to make a second 45º angle; open. Remove the ruler and fold in half lengthwise. 4. With the angled folds as valleys, and the horizontal fold as a mountain fold, bring the left and right edges together, causing the paper to form a triangular shape at the top. (See video and images below for helpful visual instructions.)

3 June 2017 Pattern Play Greetings to Go Page 3 of 5 5. With the mountain folds of the Dk. Gray accordion facing the top, slide the closed accordion between the two flaps of the folded Green mechanism. 6. Mark the area where the green flap covers the accordion, and adhere only that area to the mechanism. Flip the mechanism over, and adhere the accordion to the other flap in the same manner. 7. Score and fold the 4¼x11 Green card base horizontally at 5½. Adhere each side of the triangular areas of the mechanism to the inside of the card base. Inside: Wishing you a very special day. Inside: You re special to me. Notes for each card: Nest the sentiment onto the 1.5x4.25 Dk. Gray accordion strip and layer onto the front of the card, about 1.25 from the bottom edge. Adhere one of each rectangular cutapart design to the Dk. Gray accordion strip on the inside with the corresponding greeting. Inside: Make it awesome. Inside: Thank you!

4 June 2017 Pattern Play Greetings to Go Page 4 of 5 Set B: 3¾x7¼ Gray Pattern Cards with 3¼x6¾ Dk. Gray Panels Score and fold each 7¼x7½ Gray Pattern card base horizontally at 3¾. (Use caution. The card base is nearly square. Be sure the fold results in a 3¾x7¼ card base.) Notes: Cut angles in the Happy Birthday cutapart with a ruler and craft knife to match the angles of the artwork; tie a raffia bow onto the narrowest point and adhere to the card panel. Inside: Enjoy it to the fullest. Notes: Adhere a cutapart onto three metallic silver tags; tie polka dot ribbon to the bottom of each tag; set an eyelet into each tag and string onto raffia; secure raffia tails behind the Dk. Gray panel; trim feel better from the cutapart and adhere to the panel. Notes: Trim the printed cutapart scrap to 3.5x7 ; nest onto the card base; dry emboss the Dk. Gray panel, if desired, and adhere to the decorative panel; tie raffia onto the burst cutapart and adhere three images to the upper portion of the panel with equal spacing. Inside: Get well soon. Notes: Dry emboss the Dk. Gray panel, if desired; adhere the sentiment onto the panel, flush with the right edge; tie a black polka dot bow onto the panel and adhere to the card base. Inside: So happy for you. Inside: Our thoughts are with you.

5 June 2017 Pattern Play Greetings to Go Page 5 of 5 Set C: 4½x6¼ White Cards with 4x9¼ Green Panels Score each 4½x9¾ White card base horizontally at 3 and 4¾. Accordion fold. Score each 4x9¼ Green panel horizontally at 3 and 4¾. Fold each piece into a z shape. Notes for all cards: Position the White folded card base horizontally with the narrowest flap on the left; nest the folded Green panel onto the card base with the largest flap on the left; adhere the panel to the card, using caution to apply adhesive only to the non-moving areas. Inside: You re the best! Notes: Round select corners of the White cutaparts and White card base with a 1/4 punch; adhere one cutapart vertically onto the right edge of the large green flap; staple ribbon to the thanks cutapart and adhere horizontally, overlapping the right edge of the flap slightly. Inside: So proud of you! Notes: Tie raffia around the congrats cutapart and nest onto the front Green flap. Inside: What s up? Notes: Punch daisy shapes from the printed cutapart scrap; adhere to a silver metallic tag; set an eyelet and tie a raffia bow onto the tag; add an eyelet and bow to the hello cutapart tag and adhere the tag set to the large Green flap. Notes: Equally space three vertical cutaparts onto the Green panel, allowing the third panel to extend beyond the right edge of the flap. Inside: Hope it s amazing.