Fire Safety. Installation Instructions Model D2300CP Fiber Optic Interface INTRODUCTION ELECTRICAL CONNECTIONS MOUNTING POWER INPUT

Transcription

1 Fire Safety Installation Instructions Model Fiber Optic Interface INTRODUCTION The SIEMENS Model is a Fiber Optic interface for the MXL s RS-485 network (MNET or XNET) or the FireFinder XLS network (HNET or XNET). It uses a two fiber (duplex) pair between each device. The can function as either a repeater or an end point unit. The can operate in either a daisy chain (See Figure ) or star configuration (See Figure 2). This allows for network configurations that are not possible with the RS-485 network alone. WRNING: The module is not listed for use by Factory Mutual. pplications requiring fiber connectivity of voice modules/systems are therefore not Factory Mutual listed. WRNING: Do not use the with CXL Systems. MOUNTING The has four keyhole slots for #6 screws. Mount the device in the locations listed below using the four #6 screws provided. bracket (P/N ) is available for mounting the in any MXL enclosure that will accept a MOM-4 (See Figure 3). This bracket has the same footprint as the MOM-4 and accommodates two s. n assembly kit is included with the bracket that contains four nuts and eight screws. Mount the bracket in the enclosure with the four nuts at the positions labeled X (See Figure 3). Start four of the 6-32 screws and slip the keyhole slots in the over them. Tighten the four screws. System 3 style rails that mount on an MR or MME-3 backbox (P/N MSR-) are also available and can be used for mounting the. Up to three brackets can be installed on a single rail. bracket, Model D2300-MP, is available for mounting two s and a PS-5 in any FireFinder XLS C enclosure. The D2300-MP fits in the same footprint as a CC-5 and mounts to the C-MP. hardware kit is provided for attaching the D2300-MP to the C-MP and mounting two s and one PS-5 onto the D2300-MP. Mount the s and PS-5 prior to installing the D2300-MP onto the C- MP. Note that when using two s, the center two mounting holes on each share the two center studs on the D2300-MP ( See Figure 4). ELECTRICL CONNECTIONS INPUT The uses regulated 5 VDC at 20m. The can only be powered from the sources listed in Table. cable (P/N ) is available for use with the MM, the PSR- and the PS-5. e sure to observe polarity when connecting the 5 VDC. Damage to the can occur if the polarity is reversed. e sure not to interchange the 5 VDC and RS-485 connections as this will result in damage to the unit. SYSTEM Table SOURCE MXL MM, P0 PSR-, P3 PS-5, J3 WIRING CONNECTIONS See Figure 5 See Figure 6 See Figure 7 FireFinder XLS PS-5, J3 See Figure 7 ll wiring is power limited to NFP 70 per NEC 760. ll wiring must be in accordance with rticle 760 of NEC or local building codes. Siemens uilding Technologies, Inc. 8 Fernwood Road Florham Park, New Jersey Siemens uilding Technologies, Ltd. 2 Kenview oulevard rampton, Ontario L6T 5E4 CN P/N

2 DUPLEX OPTICL FIER UDGET - MX LOSS -3 d 62.5/25 FIER - 9 d 50/25 FIER DUPLEX OPTICL FIER UDGET - MX LOSS -3 d 62.5/25 FIER - 9 d 50/25 FIER NO CONNECTION NO CONNECTION +5 VDC - +5 VDC - +5 VDC - RS NODES MX RCC- PSR- RS NODES MX RCC- MM RS NODES MX USE THE 20 ¼ W, 5% EOL RESISTOR SSEMLY, S PPLICLE: (MM-/) OR P/N (MM-3) PSR- Figure Daisy Chain Configuration (MNET Shown) 2

3 DUPLEX OPTICL FIER UDGET - MX LOSS -3 d 62.5/25 FIER - 9 d 50/25 FIER NO CONNECTION NO CONNECTION NO CONNECTION TO DDITIONL MODULES +5 VDC - +5 VDC - +5 VDC - RS NODES MX PSR- MM USE THE 20 ¼ W, 5% EOL RESISTOR SSEMLY, S PPLICLE: (MM-/) OR P/N (MM-3) PSR- Figure 2 Star Configuration (MNET Shown) 3

4 X +5 VDC - RCKET P/N OMM- +5 VDC - X WRNING DISCONNECT PRIOR TO REMOVING TERMINL LOCK PROTECTION Figure 3 Mounting the in an MR or MME-3 ackbox FIER OPTIC CLE LIMITED HNET/XNET ROUTE S SHOWN D2300-MP NIC-C DLC P5 P T 6 2 _ + 2 T3 +5 VDC - +5 VDC - RESET CRD FIL CN FIL HNET FIL XNET FIL GND FULT LOOP FIL LOOP FIL CTIVE NETWORKS CN HNET XNET HNET/XNET STYLE STYLE 7 STYLE 4 GROUND FULT ENLED DISLED Z O N E Z O N E 2 RESET CRD FIL HNET FIL GND FULT LRM TROULE ZONES STTUS CLSS OPEN CLSS RETURN SHORT CLSS OPEN CLSS RETURN SHORT PSC-2 RESET MODULE FIL CN FIL HNET FIL GND FULT 24V 2 FIL 24V 4 FIL HNET NETWORK PORT PS HNET HNET TTERY O OFF ON 9 3 T _ T4 + P2 H N GND P9 _ + C- Figure 4 Mounting the in a C- ackbox 4

5 MM P0 LCK RED +5 VDC - CLE P/N NOTE: LOSS OF TO REKS COMMUNICTION PTH ND CUSES SYSTEM COMMUNICTION TROULE. NOTE: SEE 5 VDC CURRENT CLCULTION TO DETERMINE REQUIREMENTS. +5 VDC - Figure 5 Using the MM-/ as a Power Supply PSR- P3 LCK RED +5 VDC - CLE P/N NOTE: LOSS OF TO REKS COMMUNICTION PTH ND CUSES SYSTEM COMMUNICTION TROULE. NOTE: SEE 5 VDC CURRENT CLCULTION TO DETERMINE REQUIREMENTS. +5 VDC - Figure 6 Using the PSR- as a Power Supply Note: The total current drawn from the 5 VDC supply on either the MM, or the PSR- must not exceed their capacity. If the total current exceeds the rating, a PS-5 must be used to power the. See the 5 VDC Current Calculation section on page 7 to determine if a PS-5 is required. 5

6 CONNECT TO PSC-2 T3 24VDC VDC - PS-5 INSTLLTION INSTRUCTIONS P/N NOTE: LOSS OF TO REKS COMMUNICTION PTH ND CUSES SYSTEM COMMUNICTION TROULE. J3 + LCK RED +5 VDC - CLE P/N (NOT ) Figure 7 Using the PS-5 as a Power Supply N.C. N.C. DT DT DT DT END POINT FCP UDGET - MX LOSS -3 d 62.5/25 FIER - 9 d 50/25 FIER DT DT DT DT RS-485 NETWORK MNET/HNET/XNET (SEE FIGURES 9, 0 & ) REPETER FCP UDGET - MX LOSS -3 d 62.5/25 FIER - 9 d 50/25 FIER N.C. N.C. DT DT DT DT END POINT FCP Figure 8 Wiring the as both a Repeater and End Point Unit 6

7 5 VDC CURRENT CLCULTION (MXL ONLY) The 5 VDC output ratings for the MM and PSR- are: MM 500m at 5 VDC PSR- 800m at 5 VDC The following modules all draw current from the 5 VDC supply. dd the value for each module that is installed in the enclosure where the is to be installed. e sure to include the in this calculation. If the total is greater than the ratings above for either the MM or PSR-, a PS-5 must be used to power the. Refer to the PS-5 Installation Instructions, P/N , for wiring diagrams. CM- MODULE CTIVE 5 VDC MODULE CURRENT 76m QUNTIT Y TOTL LD 30m LDI 0m SC- 29m SC 29m CMI m CRM-4 30m CSM-4 30m CZM-4 24m 20m MK 5m NET-4 20m NET-7 20m NET-7M 20m NIM-W 60m REP- 0m MOI-7 75m MOD-6 2m MID-6 2m CZM- 0m ICP- 0m PIM- 25m Silent Knight m TMM- 0m VSM-/VLM- 0m VFM- 0m TC- 0m RCM- 80m ZC-30 0m OCC- 22m ZC-8 3m ZC2-8 3m ZC2-4 30m ZC3-4 28m ZCT-8 33m TOTL 7

8 RS-485 RTINGS: 8V P-P 50m MX 80 OHMS MX 8 WG MIN () () -DT +DT USE THE 20 ¼ W, 5% EOL RESISTOR SSEMLY, S PPLICLE: (MM-/) OR P/N (MM-3) STYLE 4 MNET MM T 4 () 3 () 2 () () -DT +DT RS-485 RTINGS: 8V P-P 50m MX 80 OHMS MX 8 WG MIN () () -DT +DT REFER TO NET-7 INSTLLTION INSTRUCTIONS P/N T NET-7 STYLE 7 MNET MOM-4 Figure 9 Wiring the RS-485 MNET Network in Style 4 and Style 7 8

9 * * * RS-485 RTINGS: 8V P-P 50m MX 80 OHMS MX 8 WG MIN *OMIT THIS EQUIPMENT FOR STYLE 4 XNET REFER TO NIM-R OR NIM-W INSTLLTION INSTRUCTIONS P/N OR P/N , S PPLICLE Figure 0 Wiring the RS-485 XNET Network in Style 4 and Style 7 (MXL) NIM-R/-W T3 RS-485 NETWORK The RS-485 MNET, XNET and HNET networks connect to the on the terminal block with the markings +DT () and -DT(2). Terminals 3 and 4 are not used. For Style 4 networks one is needed at each Fiber Optic drop. For Style 7 networks two s are needed at each drop. End of line devices are required on each RS-485 pair in the system. Install them at the extreme ends of each pair. Refer to Figures 9 and 0 (MXL) and Figure (FireFinder XLS) for wiring instructions and ratings for both Style 4 and Style 7. FIER CONNECTIONS The can function as both a repeater and an end point unit. When used as an end point connect to the fiber connectors labeled. Make no connection to the connectors. In the repeater mode use both pairs of connectors, and. Two Fiber Optic cables are required between each pair of s. Use a high quality duplex Fiber Optic cable containing either 50/25 or 62.5/25 fiber. Duplex fiber optic cable has two cables in a single shield similar to electrical zip cord. Use ST style fiber connectors. Please contact the fiber manufacturer regarding instructions for terminating the fiber. When installing the fiber pairs, each fiber must connect between the transmit data (DT ) on one and the receive data line (DT ) on the other. See Figure 7 for connection diagrams. INDICTORS The has five LED indicators for Power and Status. The LEDs are located on the side of the module with the Fiber Optic connectors. The Power LED is red and lights whenever there is 5 VDC. oth channels and have a yellow and green LED. The green LED indicates that the is transmitting data on that channel. The yellow LED lights when data is received. RTINGS Input Power attery Power RS-485 Transmitter Power MOM-4 5 VDC, 20m max 24 VDC, 50m max 8V (P-P), 50m max 25µW (-6dm) (62.5/25 Fiber) 9

10 RS-485 RTINGS: 8V P-P 50m MX 80 OHMS MX 8 WG MIN NO REQUIRED T THE NIC-C NIC-C ONE SLOT OF CC-5/CC STYLE 4 HNET/XNET RS-485 RTINGS: 8V P-P 50m MX 80 OHMS MX 8 WG MIN NO REQUIRED T THE NIC-C NIC-C ONE SLOT OF CC-5/CC STYLE 7 HNET/XNET Figure Wiring the RS-485 HNET or XNET Network in Style 4 and Style 7 (FireFinder XLS) P/N