OM7AT & OM7AR1 (Stand alone) ROM7AT & ROM7AR1 (Rack mount)
|
|
- Martha Ward
- 5 years ago
- Views:
Transcription
1 OM7AT & OM7AR1 (Stand alone) ROM7AT & ROM7AR1 (Rack mount) IRIG Time Code Electrical to Fiber Optic Transceiver Operating Manual Rev. 1.3 December 20, 2015 Luxcom Technologies Inc., 102 WALGREEN ROAD, OTTAWA, ONTARIO, K0A 1L0 Telephone: website: www. luxcom.com, Fax:
2 Description The OM7AT transmitter accepts an IRIG electrical timing signal and transmits it over a multimode fiber to an OM7AR1 where it is output electrically. The IRIGB signal must be an AM modulated sine wave; these transceivers are not suitable for the logic level signals. The ROM7AT and ROM7AR1 are dual rack- mount versions of the transceivers. The IRIG specification does not specify the electrical interface or amplitude; these transceivers have BNC connectors and accept input signals of 1 to 3.9Vpp. A switch on the receiver sets the automatic gain control stage to output a signal of either 1.3 or 3.5Vpp. The stand-alone and rack-mount versions are inter-operable. OM7AT is a stand-alone transmitter with one electrical input. OM7AR1 is a stand-alone receiver with one electrical output. ROM7AT is a rack-mount transmitter with two independent electrical inputs.* ROM7AR1 is a rack-mount receiver with two independent electrical outputs.* *These cards fit in Luxcom's RMF30 rack. OM7AT and OM7AR1 Stand-alone Transceiver 1
3 OMA7T Stand Alone Transmitter Indicators PWR: On indicates the unit is powered. 1. The transmitter is normally terminated in 75 ohms. When several transmitters are driven by the same signal in parallel all except one of them must have a high impedance termination. To do this, the box must be opened and the jumper on the 2 pin header removed. It may be stored by inserting one pin only of the jumper on the header. 2. Be sure the three pin header has the shunt on the side nearest to the optics. 3. Power the unit using the supplied 12 VDC power cube. 4. Connect the input to the signal source, preferably with a 75 Ω coaxial cable (a 50 Ω will do). 5. Connect the optical port to an OM7AR1 or ROM7AR1 using a multimode fiber. Transmitter Rack Mount Panel This 19" 1U high rack mount panel can be used when multiple OM7ATs are installed. It holds up to six OM7ATs. The OM7AT is end mounted to the panel using the supplied screws. See Ordering Information. OM7AR1 Stand Alone Receiver Indicators PWR: On indicates the unit is powered. LINK: On indicates the OM7AR1 has an optical link with the remote transmitter. RX: On indicates the OM7AR1 is outputting a signal on the BNC. 1. There are no user settable jumpers in the box. 2. Power the unit using the supplied 12 VDC power cube. 3. Connect the output to the signal destination preferably with a 75 Ω coaxial cable (a 50 Ω will do). 4. Connect the optical port to an OM7AT or ROM7AT1 using a multimode fiber. 5. Set the switch to 1.3Vpp or 3.5Vpp as required. Receiver Rack Mount Panel This 19" 1U high rack mount panel can be used when multiple OM7AR1s are installed. It holds up to six OM7AR1s. A mounting bracket attaches to the clam shell box using the box s screws. This bracket is then attached to the rack using the supplied screws. See Ordering Information. 2
4 ROM7T Rack Mount Dual Transmitter Indicators PWR: On indicates the unit is powered. 1. The transmitter is normally terminated in 75 ohms. When several transmitters are driven by the same signal in parallel all except one of them must have a high impedance termination. To do this the box must be opened and the jumper across the 2 pin header removed. It may be stored by inserting one pin only of the shunt on the header. Do this for both channels. 2. Be sure the three pin headers have the shunt on the side nearest to the optics. 3. Insert the card in Luxcom s RMF30 rack and tighten the captive screws. 4. Power up the PSU-1 power supply. 5. Connect the input to the signal source preferably with a 75 Ω coaxial cable, but a 50 Ω will do. 6. Connect the optical port to an OM7AR1 or ROM7AR1 using a multimode fiber. 7. Repeat the above for the second channel. ROM7AR1 Rack Mount Dual Receiver Indicators PWR: On indicates the unit is powered. LINK: On indicates the OM7AR1 has an optical link with the remote modem. RX: On indicates the OM7AR1 is outputting a signal on the BNC. 1. The ROM7AR1 has a jumper to set the output signal level. The 3-pin jumper in line with the optics has a shunt which when installed closest to the optics sets the output signal is 1.3Vpp, and when installed furthest from the optics sets the output signal is 3.5Vpp. Each channel must be set separately. 2. Insert the card in Luxcom s RMF30 rack and tighten the captive screws. The RMF30 rack may be powered during the previous step. 3. Connect the output to the signal destination preferably with a 75 Ω coaxial cable (a 50 Ω will do). 4. Connect the optical port to an OM7AT or ROM7AT using a multimode fiber. 3
5 OM7AT/R1 and ROM7AT/R1 Specifications Optical Light source... SLED for multimode fiber Operating Wavelength M version nm MM version nm Optical output - 50/125 fiber dbm min /125 fiber dbm min Optical Sensitivity dbm Optical Connectors... ST Operating distance with 62.5/125 fiber (at 3dB loss/km) M version... 4km (at 1dB loss/km) MM version... 12km Signal Input/Output I/O connectors... BNC coaxial Input level (terminated)... 1 to 3.9 Vpp Output level receiver set to High Vpp receiver set to Low Vpp Transmitter input impedance Ohm Recommended load impedance Ohm** Bandwidth Hz to 10 MHz Electrical Power Consumption... < 1 Watt / transmitter or receiver Power Source stand-alone versions... 2V DC power cube supplied Power Source rack mount version /220 Vac, 50/60Hz, 0.6/0.3A General Operating Temperature C to +55 C Humidity (RH)... 10% to 95% (non-condensing) Size OM7AT x 2 x 6.4 cm Size OM7AR x 2 x 8.6 cm * Specifications subject to change without notice. **If the external load impedance is 50 Ohms the received signal will be reduced by 14%. 4
6 ROM7AR/T Rack Mount Cards in a Rack Mount Chassis The RMF30 Rack must have a PSU-1 power supply installed. Two PSU-1 power supplies can be installed if redundancy is required. The figure below shows an RMF30 rack with redundant power supplies and eight ROM7AT cards. The ROM7AR1 cards look similar. RMF30 Chassis Specifications Number of Slots... 2 power supply, 16 ROM7AR/T cards Proprietary Backplane pin gold connectors Size... 3U 19 with mounting ears RMF30 Power Supply Input AC Voltage or 220 VAC switch selectable**. Input frequency to 60 Hz Input Power connector... IEC-320 receptacle RFI Suppression... Meets FCC Class A VDE 0871 Class A Front Panel ON Indicator... Green LED Power Input Watts max Output Voltages VDC +/- 5% +12 VDC +/- 20% NL to FL -8 VDC +/- 20 % NL to FL Protection... O/P Current Limiting beyond rated O/P Inrush Current Limiting Input Thermal Fuse Hiccup Short Circuit protection Low Voltage Shutdown General Operating Temperature C to +50 C Humidity (RH)... 10% to 95% MTBF... > 80,000 hrs with Single PS Dimensions... H*W*D 5.25" * 19.00" *7.55" 5
7 *Specifications subject to change without notice. **See instructions. 1. Install the RMF30 in the 19 rack with the appropriate retaining screws (not supplied). 2. A label on the power supply will indicates if it is set for 120V ac or 220V ac. If you wish to change the input voltage of the supply, a switch must be moved. The switch is visible through the ventilation holes in the bottom of the power supply. You can see the silk screen which says 115V beside the switch. You should push the slide switch with a small screw driver (through the ventilation slot) so the switch position is nearer the center of the power supply; conversely if you want 120Vac you must pull the switch so it is close to the 115V text. There is no need to remove the cover, and the unit should not be powered when you do this. If the switch is moved, the voltage labels on the supply should be adjusted accordingly. 3. Connect the power cord into the AC outlet. 4. The Green Power LED on the power supply must be lit. 5. The RMF30 is now ready to receive the option cards. These cards can be installed while the power is on or off. 6. Plug the option card in any slot except the two leftmost slots which are reserved for the main and back-up power supplies. Warranty This Luxcom Technologies product is warranted against defects in materials and workmanship for a period of five years from the date of shipment. Luxcom Technologies will, at its option, repair or replace products which prove to be defective during the warranty period provided they are returned to Luxcom Technologies. Repairs necessitated by misuse of the product are not covered by this warranty. NO OTHER WARRANTIES ARE EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. LUXCOM TECHNOLOGIES IS NOT LIABLE FOR CONSEQUENTIAL DAMAGES. Part Numbers OM7AT - x ROM7AT x OM7AR1 x ROM7AR1 x RMF30 PSU-1 1 channel stand-alone IRIG transmitter 2 channel rack-mount IRIG transmitter 1 channel stand-alone IRIG receiver 2 channel rack-mount IRIG receiver Where x is: M = 850 nm optics, or MM =1300 nm optics 16 card slot 3U chassis Power Supply for RMF30 MP-OM7T 1U 19 rack mount panel which hold up to 6 OM7ATs 6
8 MP-OM7AR 1U 19 rack mount panel which hold up to 6 OM7AR1s Revision Record: Rev Rev 1.1 July 23, 2015: On the previous manual low gain output 1Vpp, high gain output 1.7Vpp. On this revision the hardware outputs 1.3Vpp on low and 3.5Vpp on high. Rev 1.2 Clarified the installation instructions regarding the power supply input voltage range. Rev 1.3 Removed step 4 in installation instructions. 7
F290X / F293X FOM II Series Fiber Optic Isolator Technical Manual
F290X / F293X FOM II Series Fiber Optic Isolator Technical Manual Revision G Copyright 2017 VERSITRON, Inc. 83 Albe Drive / Suite C Newark, DE 19702 www.versitron.com E031130243 PROPRIETARY DATA All data
More informationInstruction Manual Model M Switch, DPDT, Manual Select
Instruction Manual Model 1582-70M Switch, DPDT, Manual Select November 2018 Rev 0 STATUS MODEL 1582 CROSS TECHNOLOGIES INC. MANUAL SELECT POWER Data, drawings, and other material contained herein are proprietary
More informationInstruction Manual MX-485-S Bi-directional RS485 Data Transceiver
Instruction Manual MX-485-S Bi-directional RS485 Data Transceiver Copyright 2005, American Fibertek, Inc. 1020JD Table of Contents Functional Description...3 Installation...3 Power Source...3 Power Connection...3
More informationInstruction Manual MTX-8485C MRX-8485C Four Channel Video Multiplexer with Bi-directional Data
Instruction Manual MTX-8485C MRX-8485C Four Channel Video Multiplexer with Bi-directional Data Copyright 2005, American Fibertek, Inc. 1027JD Table of Contents Functional Description...3 Installation...3
More informationInstruction Manual RT-93285SL RR-93285SL Thirty-two Channel Video Multiplexer With Two Bi-directional Data Channels
Instruction Manual RT-93285SL RR-93285SL Thirty-two Channel Video Multiplexer With Two Bi-directional Data Channels Copyright 2006, American Fibertek, Inc. 0222JD Table of Contents Functional Description...3
More informationF272xB Fiber optic 4-Wire Telephone/Audio Modem Technical Manual
F272xB Fiber optic 4-Wire Telephone/Audio Modem Technical Manual Revision A March 2015 VERSITRON, Inc. 83 Albe Drive / Suite C Newark, DE 19702 www.versitron.com Safeguarding Communications Since 1958
More informationModel 1791 VHF Radio User's Manual
Model 79 VHF Radio User's Manual ALL WEATHER INC 65 NATIONAL DRIVE SACRAMENTO, CA 95834 WWW.ALWEATHERINC.COM 79 VHF RADIO USER'S MANUAL CONTENTS INTRODUCTION... Description... Transmitter Module... Power
More informationEXECUTE Shiloh Road Alpharetta, Georgia (770) FAX (770) Toll Free
Instruction Manual Model 1586-06 RF Attenuator May 2009 Rev A 1 2 3 12.5 53.5 16.3 MODEL 1586 RF ATTENUATOR CROSS TECHNOLOGIES INC. EXECUTE PS1 PS2 Data, drawings, and other material contained herein are
More information285E Series DIGITAL FIBER OPTIC AUDIO/DATA TRANSPORT SYSTEM
285E Series DIGITAL FIBER OPTIC AUDIO/DATA TRANSPORT SYSTEM BCI reserves the right to make changes to the products described herein without prior notice or consent. No liability is assumed as a result
More informationInstruction Manual MTX-8485 MRX-8485 Four Channel Video Multiplexer with Bi-directional Data
Instruction Manual MTX-8485 MRX-8485 Four Channel Video Multiplexer with Bi-directional Data Copyright 2003, American Fibertek, Inc. 0530JD Table of Contents 2 Functional Description... 4 Installation...
More informationInstruction Manual MT-945SL Four Channel Video Transmitter With Two Bi-Directional Data Channels
Instruction Manual MT-945SL Four Channel Video Transmitter With Two Bi-Directional Data Channels Copyright 2006, American Fibertek, Inc. 0307JD Table of Contents Functional Description... 3 Installation...
More informationINSTRUCTION MANUAL MODEL 2779 SUBCARRIER MODULATOR
INSTRUCTION MANUAL MODEL 2779 SUBCARRIER MODULATOR Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc., and may not be reproduced or duplicated in any form without
More informationInstruction Manual MX-480 Bi-directional Multi-Protocol Data
Instruction Manual MX-480 Bi-directional Multi-Protocol Data Copyright 2007, American Fibertek, Inc. 1210JD Table of Contents Functional Description...3 Installation...3 Power Source...3 Power Connection...4
More informationaf i Instruction Manual MR-944C Four Channel Video Receiver With One Bi-Directional Multi-Protocol Data Channel american fibertek 11/30/2012 JPK
af i american fibertek Instruction Manual MR-944C Four Channel Video Receiver With One Bi-Directional Multi-Protocol Data Channel 11/30/2012 JPK Table of Contents Functional Description... 3 Installation...
More informationUser s Manual. VA700XD Series. Fiber Optic Baseband Video /Audio. Installation and User Guide
User s Manual VA700XD Series Fiber Optic Baseband Video /Audio Installation and User Guide Revision 1.0 MAY 2004 VAB700XD Series Users and Installation Manual Radiant Communications makes every effort
More informationINSTRUCTION MANUAL MODEL 2455T SUBCARRIER MODULATOR
INSTRUCTION MANUAL MODEL 2455T SUBCARRIER MODULATOR Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc., and may not be reproduced or duplicated in any form
More informationA3422 XMTDR. Digital Return Optical Transmitter Module. Features
A3422 XMTDR Digital Return Optical Transmitter Module The A3422 XMTDR digital return optical transmitter allows RF reverse path signals to be sent back to headend via a single fiber. The RF signal is routed
More informationCIRCUIT-TEST ELECTRONICS
USER'S MANUAL Sweep Function Generator with Counter SWF-8030 CIRCUIT-TEST ELECTRONICS www.circuittest.com TABLE OF CONTENTS SAFETY INFORMATION...page 3 INTRODUCTION... 4 SPECIFICATIONS... 5 FRONT PANEL
More informationSince 1987 Developed, Created and Made in Spain NDV6/ND6V VIDEO & DATA TRANSCEIVER, AUDIO & CONTACT
Since 987 Developed, Created and Made in Spain NDV6/ND6V VIDEO & DATA TRANSCEIVER, AUDIO & CONTACT CONTENTS General functionality and features of the equipment. Technical specifications. Application. Connection
More informationVi6208, Vi6216, Vi6232 Vi6308, Vi6316, Vi6332
MODELs Vi6208, Vi6216, Vi6232 Vi6308, Vi6316, Vi6332 Automatic Video Compensation UTP Receiver Hubs User s Manual 7810 Trade Street, Suite 100 San Diego, CA 92121, U.S.A. Phone: (858) 484-5209 Fax: (858)
More informationModel 7000 Low Noise Differential Preamplifier
Model 7000 Low Noise Differential Preamplifier Operating Manual Service and Warranty Krohn-Hite Instruments are designed and manufactured in accordance with sound engineering practices and should give
More informationOptiva OTS-2 40 GHz Amplified Microwave Band Fiber Optic Links
2 GHz to 4 GHz Amplified Microwave Transport System The Optiva OTS-2 4 GHz Microwave Band transmitter and receiver are ideal to construct transparent fiber optic links in the 5 MHz to 4 GHz frequency range
More information[ tima-datasheet-en v11.1 ]
specifically designed for protection, automation and control applications in power systems 60 ns (99%) maximum time deviation single or dual 10/100Base-T Ethernet port(s) VLAN / IEEE 802.1Q support RS232
More informationHydroLynx Systems, Inc.
Model 50386R-RP Receiver and Repeater Instruction Manual Document No: A102684 Document Revision Date: August, 2006 Receiving and Unpacking Carefully unpack all components and compare to the packing list.
More informationOptiva OTS-2 40 GHz Amplified Microwave Band Fiber Optic Links
5 MHz to 4 GHz Amplified Microwave Transport System The Optiva OTS-2 4 GHz Microwave Band transmitter and receiver are ideal to construct transparent fiber optic links in the 5 MHz to 4 GHz frequency range
More informationBROADBAND PREAMPLIFIER MODEL BPA khz 1 GHz
INSTRUCTION MANUAL BROADBAND PREAMPLIFIER MODEL BPA-1000 10 khz 1 GHz INSTRUCTION MANUAL THIS INSTRUCTION MANUAL AND ITS ASSOCIATED INFORMATION IS PROPRIETARY. UNAUTHORIZED REPRODUCTION IS FORBIDDEN. 1994
More informationA01-eNETL2TUV_Manual_RevH.doc. GE MDS enetl2t/u/v Manual P/N A01 Rev H
GE MDS enetl2t/u/v Manual P/N 05-4186A01 Rev H 05-4186A01 Rev H Page 1 of 7 12/19/2016 Table of Contents 1 Important Information... 3 1.1 RF Exposure... 3 1.2 FCC Approval Notice... 3 1.3 FCC Part 80 Information...
More informationSDI SPECTRADYNAMICS, INC. LOW NOISE FREQUENCY REFERENCE OPERATING MANUAL
SPECTRADYNAMICS, INC. LOW NOISE FREQUENCY REFERENCE LNFR-100E OPERATING MANUAL SPECTRADYNAMICS, INC 1849 Cherry St. Unit 2. Louisville, CO 80027 Phone: (303) 665-1852 Fax: (303) 604-6088 www.spectradynamics.com
More informationTIA-952 Optical/Electrical Converter. Operating Instructions
TIA-952 Optical/Electrical Converter Operating Instructions Terahertz Technologies Inc.169 Clear Road Oriskany NY 13424 (315) 736-3642 FAX (315) 736-4078 E-mail sales@terahertztechnologies.com 2/2012 Contents
More informationVideo/Audio Transmission System Series VA700. (formerly Series DVL4A)
Video/Audio Transmission System Series VA700 (formerly Series DVL4A) November 2000 1 VIDEO/AUDIO TRANSMISSION SYSTEM INSTRUCTION MANUAL SERIES VA700 & VA700M General The Series VA700 is a transmission
More informationDistribution Amplifiers 1
Distribution Amplifiers 1-30dB PUT 49-750 MHz 43 db GA POWER DOUBLED P/N: 1002705 REVERSE GA M MAX DESCRIPTION The R.L. DRAKE models DA8642, DA8632,, and DA7533, are broadband distribution amplifiers designed
More informationMODEL FLD-496SA 9600 Baud FIBER OPTIC/FSK MODEM
1 MODEL FLD-496SA 9600 Baud FIBER OPTIC/FSK MODEM GDI COMMUNICATIONS, LLC 280 Interstate 80 Exit 1 PO Box 1330 Verdi, NV 89439 Phone (775) 345-8000 Fax (775) 345-8010 PROPRIETARY DATA This document contains
More informationOptiva OTS-2 18 GHz Amplified Microwave Band Fiber Optic Links
MHz to 18 GHz Amplified Microwave Transport System The Optiva OTS-2 18 GHz Microwave Band transmitter and receiver are ideal to construct transparent fiber optic links in the MHz to 18 GHz frequency range
More informationModicon Quantum 140 NRP /01 Fiber Converter Modules User Guide
Modicon Quantum 140 NRP 312 00/01 EAV19662 04/2014 Modicon Quantum 140 NRP 312 00/01 Fiber Converter Modules User Guide 04/2014 EAV19662.01 www.schneider-electric.com The information provided in this documentation
More informationMODEL 3810/2 Line Impedance Stabilization Network
EMC TEST SYSTEMS FEBRUARY 1996 REV C PN 399197 MODEL 3810/2 Line Impedance Stabilization Network OPERATION MANUAL USA P.O. Box 80589 Austin, Texas 78708-0589 2205 Kramer Lane, Austin, Texas 78758-4047
More informationTime over Fiber. interfacility link systems
Time over Fiber interfacility link systems 1 PPS CW/SINE STANDARDS IRIG GPS STABLE GROUP DELAY LOW ALLAN VARIANCE DUAL REDUNDANT POWER SUPPLIES FULLY HOT-SWAPPABLE UP TO SIX LINK MODULES PER 1RU RACK MULTIPLE
More informationSDI SPECTRADYNAMICS, INC. HIGH PERFORMANCE DISTRIBUTION AMPLIFIER OPERATING MANUAL
SPECTRADYNAMICS, INC. HIGH PERFORMANCE DISTRIBUTION AMPLIFIER HPDA15RMC OPERATING MANUAL SPECTRADYNAMICS, INC 1849 Cherry St. Unit 2. Louisville, CO 80027 Phone: (303) 6651852 Fax: (303) 6046088 www.spectradynamics.com
More informationInstallation & Service Manual
869-894 MHz Installation & Service Manual Model SCA 9321-30C Single-Channel Cellular Amplifier 044-xxxxx Rev.A February 2003 2003 Powerwave Technologies Incorporated. All rights reserved. Powerwave Technologies,
More informationCALIBRATED IMPULSE GENERATOR MODEL CIG khz 1 GHz
INSTRUCTION MANUAL CALIBRATED IMPULSE GENERATOR MODEL CIG-25 10 khz 1 GHz INSTRUCTION MANUAL THIS INSTRUCTION MANUAL AND ITS ASSOCIATED INFORMATION IS PROPRIETARY. UNAUTHORIZED REPRODUCTION IS FORBIDDEN.
More informationSince 1987 Developed, Created and Made in Spain NDV5/ND5V VIDEO & DATA TRANSMITTER/RECEIVER
Since 1987 Developed, Created and Made in Spain NDV5/ND5V VIDEO & DATA TRANSMITTER/RECEIVER CTENTS General functionality and features of the equipment. Technical specifications. Application. Connection
More informationDocument # Rev. C October, GEMINI EXPRESS MULTIPLEXER User s Guide
Document # 400-2601-01 Rev. C October, 2002 GEMINI EXPRESS MULTIPLEXER User s Guide TABLE OF CONTENTS SAFETY 3 Federal Communications Commission (FCC) Statement 3 Classification of LED Transmitter Device
More informationADA416-XLR DISTRIBUTION AMPLIFIERS OPERATING AND MAINTENANCE MANUAL
ADA416-XLR DISTRIBUTION AMPLIFIERS OPERATING AND MAINTENANCE MANUAL Copyright 2015, ATI Audio Inc. DESCRIPTION Your ADA416-XLR provides four independent one-in by four-out circuit groups. A four-output
More informationAmerican Power Design, Inc.
FEATURES 4 Customer Selects Output Voltage 4 Outputs to 28 Vdc 4 Wide Input Ranges (10-20Vdc, 18-36Vdc, 20-60Vdc, 36-72Vdc) 4 Excellent Line & Load Regulation 4 Low Output Ripple 4 500 Vdc Output Isolation
More informationGPNP Inc. NT384 NT1 User Manual. Revision /6/2002. Information in this guide is subject to change without notification.
GPNP Inc. NT384 NT1 User Manual Revision 1.00 17/6/2002 Information in this guide is subject to change without notification. Copyright 2002 GPNP Inc. U.S.A. IMPORTANT SAFETY INSTRUCTIONS When using your
More informationModel 1152-ALN Phase Locked Oscillator
Model 1152-ALN Phase Locked Oscillator The Model 1152-ALN is a single frequency, very low Phase Noise PLL unit that can be used to replace your unstable microwave crystal oscillator chain with a stable
More informationImportant Safety Information
OWNER'S MANUAL Important Safety Information 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only
More informationPULSE DISTRIBUTION AMPLIFIER OPERATING MANUAL
SPECTRADYNAMICS, INC PD5-RM-B PULSE DISTRIBUTION AMPLIFIER OPERATING MANUAL SPECTRADYNAMICS, INC 1849 Cherry St. Unit 2. Louisville, CO 80027 Phone: (303) 665-1852 Fax: (303) 604-6088 www.spectradynamics.com
More informationUNICOM 2500 UNICOM Installation Operation Programming. Universal Communication Converter
User Manual UNICOM 2500 Installation Operation Programming Universal Communication Converter UNICOM 2500 Electro Industries/GaugeTech 1800 Shames Drive Westbury, New York 11590 Tel 516.334.0870 Fax 516.338.4741
More informationPart Numbers. Fiber Driver - ST/DB25M FIBER DRIVER
January 2010 MD940A-F MD940A-M Part Numbers - ST/DB25F MD940A-F - ST/DB25M MD940A-M FIBER DRIVER CUSTOMER Order toll-free in the U.S.: 877-877-BBOX (outside U.S. call 724-746-5500) SUPPORT FREE technical
More informationPARALLEL ELEMENT ANTENNA MODEL PEA-30
INSTRUCTION MANUAL PARALLEL ELEMENT ANTENNA MODEL PEA-30 10 khz 30 MHz INSTRUCTION MANUAL THIS INSTRUCTION MANUAL AND ITS ASSOCIATED INFORMATION IS PROPRIETARY. UNAUTHORIZED REPRODUCTION IS FORBIDDEN.
More informationSIR, RADAN and UtilityScan are registered trademarks of Geophysical Survey Systems, Inc..
Copyright 2001-2017 Geophysical Survey Systems, Inc. All rights reserved including the right of reproduction in whole or in part in any form Published by Geophysical Survey Systems, Inc. 40 Simon Street
More informationINSTALLATION AND MAINTENANCE MANUAL FOR GROUND MONITOR GM-250 COPYRIGHT 1983 AMERICAN MINE RESEARCH, INC.
INSTALLATION AND MAINTENANCE MANUAL FOR GROUND MONITOR GM-250 COPYRIGHT 1983 AMERICAN MINE RESEARCH, INC. MANUAL PART NUMBER 180-0036 ORIGINAL: 1-17-83 REVISION: B (8-26-86) NOT TO BE CHANGED WITHOUT MSHA
More informationDA208 & DA416 DISTRIBUTION AMPLIFIERS OPERATING AND MAINTENANCE MANUAL
DA208 & DA416 DISTRIBUTION AMPLIFIERS OPERATING AND MAINTENANCE MANUAL Copyright 2011, ATI Audio Inc. DESCRIPTION Your DA208 or DA416 provides two (DA208) or four (DA416) independent one-in by four-out
More informationFOSTCDR. Industrial Serial to Multimode Fiber Optic Converter PRODUCT INFORMATION B&B ELECTRONICS. Specifications Serial Technology
FOSTCDR pn 8684R1 FOSTCDR-0812ds page 1/5 Industrial Serial to Multimode Fiber Optic Converter Data Rates up to 115.2 kbps 2.5 Mile (4 km) Range 10 to 30 VDC Input Voltage Wide Operating Temperature 2000V
More information50 Ohm Components Brochure
50 Ohm Components Brochure Available now to download from our website, this brochure covers JFW's standard 50 Ohm components, which includes: Programmable Attenuators Manually Variable Attenuators Fixed
More informationINSTRUCTION MANUAL. March 11, 2003, Revision 3
INSTRUCTION MANUAL Model 701A Stimulator March 11, 2003, Revision 3 Copyright 2003 Aurora Scientific Inc. Aurora Scientific Inc. 360 Industrial Parkway S., Unit 4 Aurora, Ontario, Canada L4G 3V7 Tel: 1-905-727-5161
More informationExternal RF Driver. Electrical Driver for AOTF-crystal. Instruction Manual
External RF Driver Electrical Driver for AOTF-crystal Instruction Manual Table of Contents 1 General... 3 2 Compliance... 3 3 Labeling... 4 4 Interface... 5 4.1 Front Panel... 5 4.2 Back Panel... 6 4.2.1
More informationIsolated High Level Voltage Output 7B22 FEATURES APPLICATIONS PRODUCT OVERVIEW FUNCTIONAL BLOCK DIAGRAM
Isolated High Level Voltage Output 7B22 FEATURES Unity gain single-channel signal conditioning output module. Interfaces and filters a +10 V input signal and provides an isolated precision output of +10V.
More informationMODEL W Power Amplifier
TEGAM, INC. MODEL 2348 18.75 W Power Amplifier This owner s manual was as current as possible when this product was manufactured. However, products are constantly being updated and improved. Because of
More informationRIGOL. User s Guide. RP1000D Series High Voltage Differential Probe. Feb RIGOL Technologies, Inc
User s Guide RP1000D Series High Voltage Differential Probe Feb. 2013 RIGOL Technologies, Inc Guaranty and Declaration Copyright 2012 RIGOL Technologies, Inc. All Rights Reserved. Trademark Information
More informationAdvanced Test Equipment Rentals ATEC (2832)
Established 1981 Advanced Test Equipment Rentals www.atecorp.com 800-404-ATEC (2832) A.H. Systems Model Active Monopole Antennas Active Monopole Antenna Series Operation Manual 1 TABLE OF CONTENTS INTRODUCTION
More informationModels 1421 and 1422 User s Manual. Broadband Amplifiers
Models 1421 and 1422 User s Manual Broadband Amplifiers 142101 Rev. A 2 Is a registered trademark of New Focus, Inc. Warranty New Focus, Inc. guarantees its products to be free of defects for one year
More information411LA Broadband Power Amplifier
411LA Broadband Power Amplifier HIGH RF VOLTAGES MAY BE PRESENT AT THE OUTPUT OF THIS UNIT. All operating personnel should use extreme caution in handling these voltages and be thoroughly familiar with
More informationAmerican Power Design, Inc.
, Inc. FEATURES 4 Customer Selects Output Voltage 4 Ultra Wide Input Ranges (936Vdc, 2060Vdc) 4 Efficiency 89% (typ.) 4 Independently Isolated Outputs 4 SixSided Shielded Case 4 Remote On/Off Control 4
More informationAmerican Power Design, Inc.
FEATURES 4 Customer Selects Output Voltage 4 Outputs to 28 Vdc 4 Wide Input Ranges (10-20Vdc, 18-36Vdc, 20-60Vdc, 36-72Vdc) 4 Excellent Line & Load Regulation 4 500 Vdc Output Isolation 4 Continuous Short
More informationUSER MANUAL. MODEL 2017A RS-232 to 20ma Current Loop Converter. SALES OFFICE (301) TECHNICAL SUPPORT (301)
USER MANUAL MODEL 2017A RS-232 to 20ma Current Loop Converter Part# 07M2017A-A Doc# 073021UA Revised 10/15/93 SALES OFFICE (301) 975-1000 TECHNICAL SUPPORT (301) 975-1007 http://www.patton.com 1.0 WARRANTY
More informationSynthesized Base Station Transmitter
BST-25 OPERATOR S MANUAL (216 MHz) Synthesized Base Station Transmitter 357 West 2700 South Salt Lake City, Utah 84115 Phone: (800) 496-3463 Fax: (801) 484-6906 http://www.comtek.com INTRODUCTION BST-25
More informationJMAA-1800HR15. Installation and Operation Instructions. 180w Performance Series Amplifier Kit For Harley RoadGlide/ Ultra
180w Performance Series Amplifier Kit For 2015-2018 Harley RoadGlide/ Ultra # JMAA-1800HR15 2017 J&M Corporation. All rights reserved. 9/17 Installation and Operation Instructions Product Description This
More informationSPECIAL SPECIFICATION 6734 RS-232 Optical Modem
2004 Specifications CSJ 0924-06-244 SPECIAL SPECIFICATION 6734 RS-232 Optical Modem 1. Description. This Item shall govern for the furnishing and installation of Fiber Optic RS- 232 Data Modem (OTR) in
More informationFiberLink 4040 Series
MANUAL FiberLink 4040 Series Four channels of audio over one single mode or multimode fiber. Installation and Operations Manual WWW.ARTEL.COM Contents Contents Welcome... 3 Features... 3 Package Contents...
More informationRuggedNet GPoE+/Si Unmanaged 4 and 8-Port PoE/PoE+ Switch. User Manual. 38 Tesla, Irvine, CA USA Phone: (949) ; Fax: (949)
RuggedNet GPoE+/Si Unmanaged 4 and 8-Port PoE/PoE+ Switch User Manual General and Copyright Notice This publication is protected by U.S. and international copyright laws. All rights reserved. The whole
More informationX-Band Redundant LNA Systems
X-Band Redundant LNA Systems LRX-1000 Series Introduction Redundant LNA systems minimize system downtime due to LNA failure by providing a spare LNA and an automatic means of switching to the spare upon
More informationOP735. Benchtop Optical Power Meter Instruction Manual
Benchtop Optical Power Meter Instruction Manual www.optotest.com 1.805.987.1700 Contacting OptoTest Corporation 1.805.987.1700 (7:30 a.m. to 5 p.m. PST) www.optotest.com engineering@optotest.com OptoTest
More informationPTR-1500 AUDIO TONE TELEPROTECTION TERMINAL FEATURES DESCRIPTION
PTR-1500 AUDIO TONE TELEPROTECTION TERMINAL FEATURES Up to four channels per unit Full on-board programmability Available pilot tone channel Single end manual and automatic testing Modular design Audio
More informationOPERATION & SERVICE MANUAL FOR FC 110 AC POWER SOURCE
OPERATION & SERVICE MANUAL FOR FC 100 SERIES AC POWER SOURCE FC 110 AC POWER SOURCE VERSION 1.3, April 2001. copyright reserved. DWG No. FC00001 TABLE OF CONTENTS CHAPTER 1 INTRODUCTION... 1 1.1 GENERAL...
More informationUMCWB and UMCWBL INSTRUCTION MANUAL. Wideband UHF Diversity Antenna Multicouplers. Assembly and Installation Antenna Types. Fill in for your records:
INSTRUCTION MANUAL UMCWB and UMCWBL Wideband UHF Diversity Antenna Multicouplers Assembly and Installation Antenna Types Fill in for your records: Serial Number: Purchase Date: Rio Rancho, NM, USA www.lectrosonics.com
More informationRuggedNet GPoE+/Mi Managed 4 and 8-Port PoE/PoE+ Switch. Quick Start Guide. 38 Tesla, Irvine, CA USA Phone: (949) ; Fax: (949)
RuggedNet GPoE+/Mi Managed 4 and 8-Port PoE/PoE+ Switch Quick Start Guide General and Copyright Notice This publication is protected by U.S. and international copyright laws. All rights reserved. The whole
More informationUMC16B/UMC16BL. Wideband UHF Antenna Multicoupler INSTRUCTION MANUAL. Fill in for your records: Serial Number: Purchase Date:
INSTRUCTION MANUAL UMC16B/UMC16BL Wideband UHF Antenna Multicoupler RF OUT 12V DC IN 400MA MAX RF OUT Fill in for your records: Serial Number: Purchase Date: Rio Rancho, NM, USA www.lectrosonics.com UMC16B
More informationHeadend Optics Platform (CH3000)
arris.com Headend Optics Platform (CH3000) HT3580H Series Quad-Density Full Spectrum DWDM Transmitter System FEATURES DWDM transmitter: up to 16 wavelengths on ITU grid Hot plug-in/out, individually replaceable
More informationLCM100 USER GUIDE. Line Carrier Modem INDUSTRIAL DATA COMMUNICATIONS
USER GUIDE INDUSTRIAL DATA COMMUNICATIONS LCM100 Line Carrier Modem It is essential that all instructions contained in the User Guide are followed precisely to ensure proper operation of equipment. Product
More informationDigital Microwave Radios
CM Digital Microwave Radios Operating at 6, 7, 8 & 11 GHz With Capacities of 4, 8, 16E1 E3, STM-1 & 2x100BaseT The CM offers bandwidth efficient long haul data transmission for common carrier, cellular
More informationINTRODUCTION The B-24-G is a VHF band high power linear amplifier designed for the 144 MHz band. It has a maximum output power of 50W.
CONTENTS INTRODUCTION...1 FEATURES... 1 SPECIFICATIONS...2 EXPLANATION OF FEATURES...3-5 INSTALLATION... 6 DIAGRAM OF RX GAIN... 7 B-24-G OPTIONAL ADAPTORS... 8-9 PRECAUTIONS... 10-11 CONNECTION DIAGRAM...12
More informationProduct Specification. 6.1 Gb/s Short-Wavelength SFP+ Transceiver FTLF8526P3BNL
Product Specification 6.1 Gb/s Short-Wavelength SFP+ Transceiver FTLF8526P3BNL PRODUCT FEATURES Up to 6.1 Gb/s bi-directional data links Hot-pluggable SFP+ footprint Built-in digital diagnostic functions
More informationTEGAM, INC. SINGLE/DUAL CHANNEL HIGH VOLTAGE AMPLIFIER MODEL 2340/2350. Instruction Manual PN# CD Publication Date: June 2006 REV.
TEGAM, INC. SINGLE/DUAL CHANNEL HIGH VOLTAGE AMPLIFIER MODEL 2340/2350 Instruction Manual PN# 810044-CD Publication Date: June 2006 REV. C This owner s manual was as current as possible when this product
More informationCT-2 and CT-3 Channel Taggers OPERATION MANUAL
CT-2 and CT-3 Channel Taggers OPERATION MANUAL Trilithic Company Profile Trilithic is a privately held manufacturer founded in 1986 as an engineering and assembly company that built and designed customer-directed
More informationTIA-527 Balanced Optical/Electrical Converter. Operating Instructions
TIA-527 Balanced Optical/Electrical Converter Operating Instructions Terahertz Technologies Inc.169 Clear Road Oriskany NY 13424 (315) 736-3642 FAX (315) 736-4078 E-mail sales@terahertztechnologies.com
More informationSoundPals. DAC-24 User Guide. Stereo D-to-A converter
SoundPals DAC-24 User Guide Stereo D-to-A converter Printing History SoundPals DAC-24 D-to-A converter Rev. N/C SEPTEMBER 2016 Printed in U.S.A. Part Number 08-2044-00 The information contained in this
More informationINSTRUMENTS, INC. Model 2960AX Disciplined Quartz Frequency Standard 2960AX. Section Page Contents
INSTRUMENTS, INC. Model 2960AX Disciplined Quartz Frequency Standard 2960AX Section Page Contents 1.0............................. 2......................... Description 2.0.............................
More informationLTX-5520 Electrical / Optical Converter Operating Instructions
LTX-5520 Electrical / Optical Converter Operating Instructions Terahertz Technologies Inc. 169 Clear Road, Oriskany, NY 13424 (315) 736-3642 FAX (315) 736-4078 E-mail sales@terahertztechnologies.com Quick
More informationOmniConverter GPoE+/SX. User Manual. 38 Tesla, Irvine, CA USA Phone: (949) ; Fax: (949) Page 2
OmniConverter GPoE+/SX User Manual General and Copyright Notice This publication is protected by U.S. and international copyright laws. All rights reserved. The whole or any part of this publication may
More informationIsolated, Linearized Thermocouple Input 7B47 FEATURES APPLICATIONS PRODUCT OVERVIEW FUNCTIONAL BLOCK DIAGRAM
Isolated, Linearized Thermocouple Input 7B47 FEATURES Interfaces, amplifies and filters input voltages from a J, K, T, E, R, S, B or N-type thermocouple. Module provides a precision output of either +1
More informationIsolated, Thermocouple Input 7B37 FEATURES APPLICATIONS PRODUCT OVERVIEW FUNCTIONAL BLOCK DIAGRAM
Isolated, Thermocouple Input 7B37 FEATURES Interfaces, amplifies, and filters input voltages from a J, K, T, E, R, S, or B-type thermocouple. Module provides a precision output of either +1 V to +5 V or
More informationInstallation & User Guide. For Powering Distributed Audio Systems A45-X2 TWO CHANNEL AMPLIFIER
Installation & User Guide For Powering Distributed Audio Systems TWO CHANNEL AMPLIFIER A45-X2 A45-X2 TWO CHANNEL AMPLIFIER TABLE OF CONTENTS Features...1 Product Overview...2 Package Contents...4 Preparing
More information5100 Series L-Band Fiber Optic Links
LBand Fiber Optic Links The 5100Series fiber optic interfacility links (IFLs) are a high performance, costeffective alternative to coaxial cable for 950 MHz to 2050 MHz LBand satellite communications applications.
More informationC-Band Redundant LNA Systems
C-Band Redundant LNA Systems LRC-1000 Series Introduction Redundant LNA systems minimize system downtime due to LNA failure by providing a spare LNA and an automatic means of switching to the spare upon
More informationFiber Coupled Laser Sources
Fiber Coupled Laser Sources Operating Manual FIBER LASER SOURCE LD PWR ADJ. OFF mw LASER APERTURE ENABLE LASER POWER FIBER DFB LASER SOURCE LD PWR ADJ. TEMP. ADJUST OFF LASER APERTURE POWER ENABLE LASER
More information80-MHz Balanced Photoreceivers Model 18X7
USER S GUIDE 80-MHz Balanced Photoreceivers Model 18X7 2584 Junction Ave. San Jose, CA 95134-1902 USA phone: (408) 919 1500 e-mail: contact@newfocus.com www.newfocus.com Warranty New Focus, a division
More informationmodel 101 single channel microphone preamplifier owner s manual Rev C
2434 30th street, boulder, CO 80306-0204 USA tel 303.443.7454 fax 303.444.4634 info@gracedesign.com / www.gracedesign.com single channel microphone preamplifier Rev C all contents Grace Design/ Lunatec
More informationOPERATING MANUAL VOLTAGE CONTROLLED OSCILLATOR MODEL NUMBER: 21XXX-YYY-ZASVCO DOCUMENT NUMBER: 51A18410
OPERATING MANUAL VOLTAGE CONTROLLED OSCILLATOR MODEL NUMBER: 21XXX-YYY-ZASVCO DOCUMENT NUMBER: 51A18410 This Operating Manual is for use with Variable Frequency AOM Drivers with model numbers: XXX = The
More informationInstruction Manual Model Upconverter
Instruction Manual Model 2006-01 Upconverter October 2013, Rev. B IF IN RF OUT Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc., but may be reproduced or
More information