Table of contents Doc: DPD00716A1, Date:

Transcription

1 VACON 20

2 Table of contents Doc: DPD00716A1, Date: Safety Warnngs Safety nstructons Earthng and earth fault protecton Before runnng the motor 5 2.Recept of delvery Type desgnaton code Storage Mantenance Capactor recharge Warranty Manufacturer s declaraton of conformty 9 3.Installaton Mechancal nstallaton Vacon 20 dmensons Coolng Power losses EMC levels Changng the EMC protecton class from C2 or C3 to C Cablng and connectons Power cablng Control cablng Screw of cables Cable and fuse specfcatons General cablng rules Strppng lengths of motor and mans cables Cable nstallaton and the UL standards Cable and motor nsulaton checks 37 4.Commssonng Commssonng steps of Vacon Fault tracng 40 6.Vacon 20 applcaton Interface Introducton Control I / O 46 7.Control panel General Dsplay Keypad Navgaton on the Vacon 20 control panel 51

3 7.4.1.Man menu Reference menu Montorng menu Parameter menu System menu 58 8.Standard applcaton parameters Quck setup par. (Vrtual menu, shows when par = 1) Motor settngs (Control panel: Menu PAR -> P1) Start / stop setup (Control panel: Menu PAR -> P2) Frequency references (Control panel: Menu PAR -> P3) Ramps and brakes setup (Control panel: Menu PAR -> P4) Dgtal nputs (Control panel: Menu PAR -> P5) Analogue nputs (Control panel: Menu PAR -> P6) Pulse tran / Encoder (Control panel: Menu PAR -> P7) Dgtal outputs (Control panel: Menu PAR -> P8) Analogue outputs (Control panel: Menu PAR -> P9) Feldbus Data-Mappng (Control panel: Menu PAR -> P10) Prohbted Frequences (Control panel: Menu PAR -> P11) Lmt Supervsons (Control panel: Menu PAR -> P12) Protectons (Control panel: Menu PAR -> P13) Fault autoreset parameters (Control panel: Menu PAR -> P14) PID control parameters (Control panel: Menu PAR -> P15) Motor Pre-heat (Control panel: Menu PAR -> P16) Easy usage menu (Control panel: Menu PAR -> P17) System parameters 81 9.Parameter descrptons Motor settngs (Control panel: Menu PAR -> P1) Start / stop setup (Control panel: Menu PAR -> P2) Frequency references (Control panel: Menu PAR -> P3) Ramps & brakes setup (Control panel: Menu PAR -> P4) Dgtal nputs (Control panel: Menu PAR -> P5) Analogue nputs (Control panel: Menu PAR -> P6) Pulse tran / Encoder (Control panel: Menu PAR -> P7) Dgtal outputs (Control panel: Menu PAR -> P8) Analogue outputs (Control panel: Menu PAR -> P9) Feldbus Data-Mappng (Control panel: Menu PAR -> P10) Prohbted Frequences (Control panel: Menu PAR -> P11) Protectons (Control panel:menu Par->P13) Automatc reset (Control panel: Menu PAR -> P14) PID control parameters (Control panel: Menu PAR -> P15) Applcaton settng (Control panel: Menu PAR->P17) 118

4 9.16.System parameter Modbus RTU Termnaton resstor Modbus address area Modbus process data Techncal data Vacon 20 techncal data Power ratngs Vacon 20 Mans voltage V Vacon 20 Mans voltage 115 V Vacon 20 Mans voltage V Vacon 20 Mans voltage 575 V Brake resstors 131

5 safety vacon 1 1. SAFETY ONLY A COMPETENT ELECTRICIAN IS ALLOWED TO CARRY OUT THE ELECTRICAL INSTALLATION! Ths manual contans clearly marked cautons and warnngs whch are ntended for your personal safety and to avod any unntentonal damage to the product or connected applances. Please read the nformaton ncluded n cautons and warnngs carefully: =Dangerous voltage Rsk of death or severe njury =General warnng Rsk of damage to the product or connected applances 1.1 Warnngs The components of the power unt of the frequency converter are lve when Vacon 20 s connected to mans. Comng nto contact wth ths voltage s extremely dangerous and may cause death or severe njury. The control unt s solated from the mans potental. The motor termnals U, V, W (T1, T2, T3) and the possble brake resstor termnals - / + are lve when Vacon 20 s connected to mans, even f the motor s not runnng. The control I / O-termnals are solated from the mans potental. However, the relay output termnals may have a dangerous control voltage present even when Vacon 20 s dsconnected from mans. The earth leakage current of Vacon 20 frequency converters exceeds 3.5 ma AC. Accordng to standard EN , a renforced protectve ground connecton must be ensured. If the frequency converter s used as a part of a machne, the machne manufacturer s responsble for provdng the machne wth a man swtch (EN ). If Vacon 20 s dsconnected from mans whle runnng the motor, t remans lve f the motor s energzed by the process. In ths case the motor functons as a generator feedng energy to the frequency converter. 24-hour support +358 (0) Emal: vacon@vacon.com 1

6 2 vacon safety After dsconnectng the frequency converter from the mans, wat untl the fan stops and the ndcators on the dsplay go out. Wat 5 more mnutes before dong any work on Vacon 20 connectons. The motor can start automatcally after a fault stuaton, f the autoreset functon has been actvated. 1 Tel (0) Fax +358 (0)

7 safety vacon Safety nstructons The Vacon 20 frequency converter has been desgned for fxed nstallatons only. Do not perform any measurements when the frequency converter s connected to the mans. Do not perform any voltage wthstand tests on any part of Vacon 20. The product safety s fully tested at factory. Pror to measurements on the motor or the motor cable, dsconnect the motor cable from the frequency converter. Do not open the cover of Vacon 20. Statc voltage dscharge from your fngers may damage the components. Openng the cover may also damage the devce. If the cover of Vacon 20 s opened, warranty becomes vod. 1.3 Earthng and earth fault protecton The Vacon 20 frequency converter must always be earthed wth an earthng conductor connected to the earthng termnal. See fgure below: MI1 - MI3 24-hour support +358 (0) Emal: vacon@vacon.com 1

8 4 vacon safety MI4 MI5 The earth fault protecton nsde the frequency converter protects only the converter tself aganst earth faults. If fault current protectve swtches are used they must be tested wth the drve wth earth fault currents that are possble to arse n fault stuatons. 1 Tel (0) Fax +358 (0)

9 safety vacon Before runnng the motor Checklst: Before startng the motor, check that the motor s mounted properly and ensure that the machne connected to the motor allows the motor to be started. Set the maxmum motor speed (frequency) accordng to the motor and the machne connected to t. Before reversng the motor shaft rotaton drecton make sure that ths can be done safely. Make sure that no power correcton capactors are connected to the motor cable. 24-hour support +358 (0) Emal: vacon@vacon.com 1

10 6 vacon recept of delvery 2. RECEIPT OF DELIVERY After unpackng the product, check that no sgns of transport damages are to be found on the product and that the delvery s complete (compare the type desgnaton of the product to the code below). Should the drve have been damaged durng the shppng, please contact prmarly the cargo nsurance company or the carrer. If the delvery does not correspond to your order, contact the suppler mmedately. 2.1 Type desgnaton code VACON0020-1L OPTIONS Vacon 20 Input phase 1L = Sngle phase 3L = Three phases Output Current Input Voltage 1 =115V 2 = V 4 = V 7 = 575V +Optons EMC2 QPES QFLG Language of the documentaton +DLCN = Chnese +DLNL = Dutch +DLCZ = Czech +DLNO = Norwegan +DLDE = German +DLPT = Portuguese +DLDK = Dansh +DLRU = Russan +DLES = Spansh +DLSE = Swedsh +DLFI = Fnnsh +DLTR = Turksh +DLFR = French +DLUS = US Englsh +DLIT = Italan empty = Englsh Fgure 2.1: Vacon 20 type desgnaton code 2.2 Storage If the frequency converter s to be kept n store before use make sure that the ambent condtons are acceptable: Storng temperature C Relatve humdty < 95%, no condensaton 2 Tel (0) Fax +358 (0)

11 recept of delvery vacon Mantenance In normal operatng condtons, Vacon 20 frequency converters are mantenancefree. However, regular mantenance s recommended to ensure a trouble-free operatng and a long lfetme of the drve. We recommended to follow the table below for mantenance ntervals. Mantenance nterval Whenever necessary Regular 12 months (If stored) 6-24 months (dependng on envronment) 5-7 years Mantenance acton Clean headsnk Check tghtenng torques of termnals Check nput and output termnals and control I / O termnals. Clean coolng tunnel. Check operaton of coolng fan, check for corroson on termnals, busbars and other surfaces. Chang coolng fans: Man fan Intermnal fan The motor cables should cross other cables at an angle of 90 degrees Capactor recharge After a longer storage tme the capactors need to be recharge n order to avod capactor damage. Possble hgh leakage current through the capactors must be lmted. The best way to acheve ths s to use a DC-power supply wth adjustable current lmt. 1) Set the current lmt to ma accordng to the sze of the drve. 2) Then connect the DC-power supply to the nput phase L1 and L2. 3) Then set the DC-voltage to the nomnal DC-voltage level of the (1.35*Un AC) and supply the converter for at least 1 h. If DC-voltage s not avalable and the unt has been stored much longer than 12 months deenergzed, consult the factory before connectng power. 24-hour support +358 (0) Emal: vacon@vacon.com 2

12 8 vacon recept of delvery 2.4 Warranty Only manufacturng defects are covered by the warranty. The manufacturer assumes no responsblty for damages caused durng or resultng from transport, recept of the delvery, nstallaton, commssonng or use. The manufacturer shall n no event and under no crcumstances be held responsble for damages and falures resultng from msuse, wrong nstallaton, unacceptable ambent temperature, dust, corrosve substances or operaton outsde the rated specfcatons. Nether can the manufacturer be held responsble for consequental damages. The Manufacturer's tme of warranty s 18 months from the delvery or 12 months from the commssonng whchever expres frst (Vacon Warranty Terms). The local dstrbutor may grant a warranty tme dfferent from the above. Ths warranty tme shall be specfed n the dstrbutor's sales and warranty terms. Vacon assumes no responsblty for any other warrantes than that granted by Vacon tself. In all matters concernng the warranty, please contact frst your dstrbutor. 2 Tel (0) Fax +358 (0)

13 recept of delvery vacon Manufacturer s declaraton of conformty EU DECLARATION OF CONFORMITY We Manufacturer's name: Vacon Oyj Manufacturer's address: P.O.Box 25 Runsornte 7 FIN Vaasa Fnland hereby declare that the product Product name: Vacon 20 Frequency Converter Model desgnaton: Vacon201L00012 to Vacon 20 3L to Vacon203L00014 to has been desgned and manufactured n accordance wth the followng standards: Safety: EN (2009) (as relevant), EN (2007) EMC: EN (2004) and conforms to the relevant safety provsons of the Low Voltage Drectve 2006/95/EC and EMC Drectve 2004/108/EC. It s ensured through nternal measures and qualty control that the product conforms at all tmes to the requrements of the current Drectve and the relevant standards. In Vaasa, 30th of July, 2010 Vesa Las Presdent The year the CE markng was affxed: hour support +358 (0) Emal: vacon@vacon.com 2

14 BACK RESET OK LOC REM BACK RESET OK LOC REM BACK RESET OK LOC REM BACK RESET OK LOC REM BACK RESET OK LOC REM 10 vacon nstallaton 3 INSTALLATION 3.1 Mechancal nstallaton There are two possble ways to mount Vacon 20 n the wall. For MI1-MI3, ether screw or DIN-ral mountng; For MI4-MI5, screw or flange mountng. The mountng dmensons are gven on the back of the drve and on the followng page. MI1 =M4 MI2 =M5 MI3 M5 Fgure 3.1: Screw mountng, MI1 - MI3 MI4 =M 6 MI5 =M 6 Fgure 3.2: Screw mountng, MI4 - MI5 3 Tel (0) Fax +358 (0)

15 BACK RESET OK LOC REM nstallaton vacon Fgure 3.3: DIN-ral mountng, MI1 - MI3 Fgure 3.4: Flange mountng, MI4 - MI5 24-hour support (0) Emal: vacon@vacon.com 3

16 BACK RESET BACK RESET OK LOC REM LOC REM 12 vacon nstallaton Vacon 20 dmensons W2 W3 D2 H1 OK H2 H3 W1 Fgure 3.5: Vacon 20 dmensons, MI1 - MI3 D1 W2 W3 D2 H1 H2 H3 W1 Fgure 3.6: Vacon 20 dmensons, MI4 - MI5 D1 3 Tel (0) Fax +358 (0)

17 nstallaton vacon 13 Type H1 H2 H3 W1 W2 W3 D1 D2 MI MI MI MI MI Table 1: Vacon 20 dmensons n mllmetres Frame Dmensons(mm) Weght* W H D (kg.) MI MI MI MI MI *wthout shppng package Table 2: Vacon 20 frame dmensons (mm) and weghts (kg) Frame Dmensons(Inches) Weght* W H D (Ibs.) MI MI MI MI MI *wthout shppng package Table 3: Vacon 20 frame dmensons (Inch) and weghts (Ibs) 24-hour support (0) Emal: vacon@vacon.com 3

18 14 vacon nstallaton Coolng Enough free space shall be left above and below the frequency converter to ensure suffcent ar crculaton and coolng. You wll fnd the requred dmensons for free space n the table below. If several unts are mounted above each other the requred free space equals C + D (see fgure below). Moreover, the outlet ar used for coolng by the lower unt must be drected away from the ar ntake of the upper unt. The amount of coolng ar requred s ndcated below. Also make sure that the temperature of the coolng ar does not exceed the maxmum ambent temperature of the converter. Mn clearance (mm) Type A* B* C D MI MI MI MI MI Table 3.1: Mn. clearances around AC drve C A A B B *. Mn clearance A and B for drves for MI1 ~ MI3 can be 0 mm f the ambent temperature s below 40 degrees. D Fgure 3.7: Installaton space A = clearance around the freq. converter (see also B) B = dstance from one frequency converter to another or dstance to cabnet wall C = free space above the frequency converter D = free space underneath the frequency converter NOTE! See the mountng dmensons on the back of the drve. Leave free space for coolng above (100 mm), below (50 mm), and on the sdes (20 mm) of Vacon 20! (For MI1 - MI3, sde-to-sde nstallaton allowed only f the ambent temperature s below 40 C; For MI4-MI5, sde-to-sde nstallaton s not allowed. Type Coolng ar requred (m³/h) MI1 10 MI2 10 MI3 30 MI4 45 MI5 75 Table 3.2: Requred coolng ar 3 Tel (0) Fax +358 (0)

19 nstallaton vacon Power losses If the operator wants to rase the swtchng frequency of the drve for some reason (typcally e.g. n order to reduce the motor nose), ths nevtably affects the power losses and coolng requrements, for dfferent motor shaft power, operator can select the swtchng frequency accordng to the graphs below. MI1 - MI5 3P 380 V POWER LOSS 24-hour support (0) Emal: vacon@vacon.com 3

20 16 vacon nstallaton 3 Tel (0) Fax +358 (0)

21 nstallaton vacon 17 MI1 - MI5 3P 230 V POWER LOSS 24-hour support (0) Emal: vacon@vacon.com 3

22 18 vacon nstallaton 3 Tel (0) Fax +358 (0)

23 nstallaton vacon hour support (0) Emal: 3

24 20 vacon nstallaton MI1 - MI3 1P 230 V POWER LOSS 3 Tel (0) Fax +358 (0)

25 nstallaton vacon hour support (0) Emal: 3

26 22 vacon nstallaton EMC levels EN defnes the dvson of frequency converters nto fve classes accordng to the level of electromagnetc dsturbances emtted, the requrements of a power system network and the nstallaton envronment (see below). The EMC class of each product s defned n the type desgnaton code. Category C1: Frequency converters of ths class comply wth the requrements of category C1 of the product standard EN (2004). Category C1 ensures the best EMC characterstcs and t ncludes converters the rated voltage of whch s less than 1000 V and whch are ntended for use n the 1st envronment. NOTE: The requrements of class C are fulflled only as far as the conducted emssons are concerned. Category C2: Frequency converters of ths class comply wth the requrements of category C2 of the product standard EN (2004). Category C2 ncludes converters n fxed nstallatons and the rated voltage of whch s less than 1000 V. The class C2 frequency converters can be used both n the 1st and the 2nd envronment. Category C3: Frequency converters of ths class comply wth the requrements of category C3 of the product standard EN (2004). Category C3 ncludes converters the rated voltage of whch s less than 1000 V and whch are ntended for use n the second envronment only. Category C4: The drves of ths class do not provde EMC emsson protecton. These knds of drves are mounted n enclosures. Envronments n product standard EN (2004) Frst envronment: Envronment that ncludes domestc premses. It also ncludes establshments drectly connected wthout ntermedate transformers to a low-voltage power supply network whch supples buldngs used for domestc purposes. NOTE: houses, apartments, commercal premses or offces n a resdental buldng are examples of frst envronment locatons. Second envronment: Envronment that ncludes all establshments other than those drectly connected to a low-voltage power supply network whch supples buldngs used for domestc purposes. NOTE: ndustral areas, techncal areas of any buldng fed from a dedcated transformer are examples of second envronment locatons Changng the EMC protecton class from C2 or C3 to C4 The EMC protecton class of MI1-3 frequency converters can be changed from class C2 or C3 to class C4 by removng the EMC-capactor dsconnectng screw, see fgure below. MI4 & 5 can also be changed by removng the EMC jumpers. Note! Do not attempt to change the EMC level back to class C2 or C3. Even f the procedure above s reversed, the frequency converter wll no longer fulfl the EMC requrements of class C2 / C3! 3 Tel (0) Fax +358 (0)

27 nstallaton vacon 23 Fgure 3.8: EMC protecton class, MI1 - MI3 Fgure 3.9: EMC protecton class, MI4 24-hour support (0) Emal: vacon@vacon.com 3

28 24 vacon nstallaton Fgure 3.10: EMC protecton class, MI5 Fgure 3.11: Jumpers Remove the man cover and locate the two jumpers. Dsconnect the RFI-flters from ground by lftng the jumpers up from ther default postons. See Fgure Tel (0) Fax +358 (0)

29 nstallaton vacon Cablng and connectons Power cablng Note! Tghtenng torque for power cables s Nm 3~ (230V, 400V) 1~ (230V) Motor out MAINS Strp the plastc cable coatng for 360 earthng MOTOR Fgure 3.12: Vacon 20 power connectons, MI1 3~(230V, 400V, 575V) External brake resstor 3~(230V, 400V, 575V) Strp the plastc cable coatng for 360 earthng 1~ (230V) 1~ (115V) Motor out L1 L2/N L3 R+ R- U/T1 V/T2 W/T3 MAINS BRAKE RESISTOR MOTOR Fgure 3.13: Vacon 20 power connectons, MI2 - MI3 24-hour support (0) Emal: vacon@vacon.com 3

30 26 vacon nstallaton 3~ (380, 480V) Motor out MAINS Brake RESISTOR MOTOR Fgure 3.14: Vacon 20 power connectons, MI4 3~ (380, 480V) Motor out MAINS Brake RESISTOR MOTOR Fgure 3.15: Vacon 20 power connectons, MI5 3 Tel (0) Fax +358 (0)

31 nstallaton vacon Control cablng Attach the support AFTER nstallng the power cables Attach ths plate BEFORE nstallng the power cables Fgure 3.16: Mount the PE-plate and API cable support, MI1 - MI3 24-hour support (0) Emal: vacon@vacon.com 3

32 28 vacon nstallaton Attach the support AFTER nstallng Attach ths plate BEFORE nstallng the power cables Fgure 3.17: Mount the PE-plate and API cable support, MI4 - MI5 3 Tel (0) Fax +358 (0)

33 nstallaton vacon 29 Fgure 3.18: Open the ld, MI1 - MI3 Fgure 3.19: Open the ld, MI4 - MI5 24-hour support (0) Emal: vacon@vacon.com 3

34 30 vacon nstallaton Control cable tghtenng torque: 0.4 Nm Strp the plastc cable coatng for 360 earthng Fgure 3.20: Install the control cables. MI1 - MI3. See Chapter 6.2 Fgure 3.21: Install the control cables. MI4 - MI5. See Chapter Tel (0) Fax +358 (0)

35 nstallaton vacon Screw of cables M4*8-12 Pcs Fgure 3.22: MI1 screws M4-8 Screws 14 Pcs Fgure 3.23: MI2 screws 24-hour support (0) Emal: 3

36 32 vacon nstallaton M4-8 Screws 10 Pcs Fgure 3.24: MI3 screws M4-10 Screws 4 Pcs M4*9 Screws 14 Pcs M4*17 Screws 6 Pcs Fgure 3.25: MI4 - MI5 screw 3 Tel (0) Fax +358 (0)

37 nstallaton vacon Cable and fuse specfcatons Use cables wth heat resstance of at least +70 C. The cables and the fuses must be dmensoned accordng to the tables below. Installaton of cables accordng to UL regulatons s presented n Chapter The fuses functon also as cable overload protecton. These nstructons apply only to cases wth one motor and one cable connecton from the frequency converter to the motor. In any other case, ask the factory for more nformaton. EMC category cat. C2 cat. C3 cat. C4 Mans cable types Motor cable types Control cable types Table 3.3: Cable types requred to meet standards. EMC categores are descrbed n Chapter Cable type Descrpton Power cable ntended for fxed nstallaton and the specfc mans voltage. 1 Shelded cable not requred. (NKCABLES / MCMK or smlar recommended) Power cable equpped wth concentrc protecton wre and ntended for 2 the specfc mans voltage. (NKCABLES / MCMK or smlar recommended). Power cable equpped wth compact low-mpedance sheld and ntended for the specfc mans voltage. 3 (NKCABLES / MCCMK, SAB / ÖZCUY-J or smlar recommended). *360º earthng of both motor and FC connecton requred to meet the standard Screened cable equpped wth compact low-mpedance sheld (NKCA- 4 BLES /Jamak, SAB / ÖZCuY-O or smlar). Table 3.4: Cable type descrptons 24-hour support (0) Emal: vacon@vacon.com 3

38 34 vacon nstallaton Frame Type Fuse [A] Mans cable Cu [mm 2 ] Motor cable Cu [mm 2 ] Termnal cable sze (mn/max) Man termnal [mm 2 ] Earth termnal [mm 2 ] Control termnal [mm 2 ] Relay termnal [mm 2 ] MI * * MI *6+6 3* Table 3.5: Cable and fuse szes for Vacon 20, 115 V, 1~ Frame Type Fuse [A] Mans cable Cu [mm 2 ] Motor cable Cu [mm 2 ] Termnal cable sze (mn/max) Man termnal [mm 2 ] Earth termnal [mm 2 ] Control termnal [mm 2 ] Relay termnal [mm 2 ] MI * * MI * * MI *6+6 3* Table 3.6: Cable and fuse szes for Vacon 20, V, 1~ Frame Type Fuse [A] Mans cable Cu [mm 2 ] Motor cable Cu [mm 2 ] Termnal cable sze (mn/max) Man termnal [mm 2 ] Earth termnal [mm 2 ] Control termnal [mm 2 ] Relay termnal [mm 2 ] MI * * MI * * MI * * MI *6+6 3* Cu MI * * Cu / Al Table 3.7: Cable and fuse szes for Vacon 20, V, 3~ 3 Tel (0) Fax +358 (0)

39 nstallaton vacon 35 Frame Type Fuse [A] Mans cable Cu [mm 2 ] Motor cable Cu [mm 2 ] Termnal cable sze (mn/max) Man termnal [mm 2 ] Earth termnal [mm 2 ] Control termnal [mm 2 ] Relay termnal [mm 2 ] MI * * MI * * MI * * MI *6+6 3* Cu MI * * Cu / Al Table 3.8: Cable and fuse szes for Vacon 20, V, 3~ Frame Type Fuse [A] Mans cable Cu [mm 2 ] Motor cable Cu [mm 2 ] Termnal cable sze (mn/max) Man termnal [mm 2 ] Earth termnal [mm 2 ] Control termnal [mm 2 ] Relay termnal [mm 2 ] MI * * MI * * MI * * Table 3.9: Cable and fuse szes for Vacon 20, 575 V Note! To fulfl standard EN , the protectve co nductor should be at least 10 mm 2 Cu or 16 mm 2 Al. Another possblty s to use an addtonal protectve conductor of at least the same sze as the orgnal one. 24-hour support (0) Emal: vacon@vacon.com 3

40 36 vacon nstallaton General cablng rules 1 Before startng the nstallaton, check that none of the components of the frequency converter s lve. Place the motor cables suffcently far from other cables: Avod placng the motor cables n long parallel lnes wth other cables. If the motor cable runs n parallel wth other cables, the mnmum dstance between the motor cable and other cables s 0.3 m. The gven dstance also apples between the motor cables and sgnal cables 2 of other systems. The maxmum length of the motor cables for MI1-3 s 30 m. For MI4 & 5, maxmum length s 50 m, f use longer cable, current accuracy wll be decreased. The motor cables should cross other cables at an angle of 90 degrees. 3 If cable nsulaton checks are needed, see Chapter Connectng the cables: Strp the motor and mans cables as advsed n Fgure Connect the mans, motor and control cables nto ther respectve termnals, see Fgures Note the tghtenng torques of power cables and control cables gven n page 25 and page 30. For nformaton on cable nstallaton accordng to UL regulatons see Chapter Make sure that the control cable wres do not come n contact wth the electronc components of the unt. 4 If an external brake resstor (opton) s used, connect ts cable to the approprate termnal. Check the connecton of the earth cable to the motor and the frequency converter termnals marked wth Connect the separate sheld of the motor cable to the earth plate of the frequency converter, motor and the supply centre. 3 Tel (0) Fax +358 (0)

41 nstallaton vacon Strppng lengths of motor and mans cables Earth conductor 8 mm 8 mm 35 mm 20 mm Fgure 3.26: Strppng of cables Note! Strp also the plastc cover of the cables for 360 degree earthng. See Fgures 3.12, 3.13 and Cable nstallaton and the UL standards To meet the UL (Underwrters Laboratores) regulatons, a UL-approved copper cable wth a mnmum heat-resstance of +60 / 75 C must be used Cable and motor nsulaton checks These checks can be performed as follows f motor or cable nsulatons are suspected to be faulty. 1. Motor cable nsulaton checks Dsconnect the motor cable from termnals U / T1, V / T2 and W / T3 of the frequency converter and from the motor. Measure the nsulaton resstance of the motor cable between each phase conductor as well as between each phase conductor and the protectve ground conductor. The nsulaton resstance must be >1 MOhm. 2. Mans cable nsulaton checks Dsconnect the mans cable from termnals L1, L2 / N and L3 of the frequency converter and from the mans. Measure the nsulaton resstance of the mans cable between each phase conductor as well as between each phase conductor and the protectve ground conductor. The nsulaton resstance must be >1 MOhm. 3. Motor nsulaton checks Dsconnect the motor cable from the motor and open the brdgng connectons n the motor connecton box. Measure the nsulaton resstance of each motor wndng. The measurement voltage must equal at least the motor nomnal voltage but not exceed 1000 V. The nsulaton resstance must be >1 MOhm. 24-hour support (0) Emal: vacon@vacon.com 3

42 38 vacon commssonng 4. COMMISSIONING Before commssonng, read the warnngs and nstructons lsted n Chapter 1! 4.1 Commssonng steps of Vacon 20 1 Read carefully the safety nstructons n Chapter 1 and follow them. 2 After the nstallaton, make sure that: both the frequency converter and the motor are grounded. the mans and motor cables comply wth the requrements gven n Chapter the control cables are located as far as possble from the power. cables (see Chapter 3.2.5, step 2) and the shelds of the shelded cables are connected to protectve earth. 3 Check the qualty and quantty of coolng ar (Chapter 3.1.2). 4 Check that all Start / Stop swtches connected to the I / O termnals are n Stopposton. 5 Connect the frequency converter to mans. 6 Set the parameters of group 1 accordng to the requrements of your applcaton. At least the followng parameters should be set: motor nomnal speed (par. 1.3) motor nomnal current (par. 1.4) applcaton type (par. 17.1) You wll fnd the values needed for the parameters on the motor ratng plate. 4 Tel (0) Fax +358 (0)

43 commssonng vacon 39 Perform test run wthout motor. Perform ether Test A or Test B: A) Control from the I / O termnals: Turn the Start/Stop swtch to ON poston. Change the frequency reference (potentometer). Check the Montorng Menu and make sure that the value of Output frequency changes accordng to the change of frequency reference. Turn the Start / Stop swtch to OFF poston. B) Control from the keypad: Select the keypad as the control place wth par 2.1. You can also move to keypad control by pressng Loc / Rem button or select Local control wth par 2.5. Push the Start button on the keypad. Check the Montorng Menu and make sure that the value of Output frequency. changes accordng to the change of frequency reference. Push the Stop button on the keypad. Run the no-load tests wthout the motor beng connected to the process, f possble. If ths s mpossble, secure the safety of each test pror to runnng t. Inform your co-workers of the tests. Swtch off the supply voltage and wat up untl the drve has stopped. Connect the motor cable to the motor and to the motor cable termnals of the frequency converter. See to that all Start / Stop swtches are n Stop postons. Swtch the mans ON. Repeat test 7A or 7B. Perform an dentfcaton run (see par. 1.18), especally f the applcaton requres a hgh startup torque or a hgh torque wth low speed. Connect the motor to the process (f the no-load test was runnng wthout the motor beng connected). Before runnng the tests, make sure that ths can be done safely. Inform your co-workers of the tests. Repeat test 7A or 7B. 24-hour support (0) Emal: vacon@vacon.com 4

44 40 vacon fault tracng 5. FAULT TRACING Note: The fault codes lsted n ths chapter are vsble f the Applcaton Interface has a dsplay, lke e.g. n control board or f a personal computer has been connected to the drve. When a fatal fault s detected by the frequency converter control electroncs, the drve wll stop and the symbol FT and the fault code blnked on the dsplay are n the followng format, e.g.: FT. 02 Fault code (02 = overvoltage) The actve fault can be reset by pressng BACK / RESET button when the API s n actve fault menu level (FT XX), or pressng BACK / RESET button wth long tme (> 2 s) when the API s n actve fault submenu level (F5.x ), or va the I / O termnal or feld bus. Reset fault hstory (long push > 5 s), when the API s n fault hstory submenu level (F6.x). The faults wth subcode and tme labels are stored n the Fault hstory submenu whch can be browsed. The dfferent fault codes, ther causes and correctng actons are presented n the table below. Fault code Fault name Possble cause Correctng actons 1 Overcurrent 2 Overvoltage 3 Earth fault Table 5.1: Fault codes Frequency converter has detected too hgh a current (>4*I N ) n the motor cable: sudden heavy load ncrease short crcut n motor cables unsutable motor The DC-lnk voltage has exceeded the nternal safety lmt: deceleraton tme s too short hgh overvoltage spkes n mans Check loadng. Check motor sze. Check cables. Increase the deceleraton tme (Par.4.3) Current measurement has detected extra leakage current at Check motor cables and start: motor nsulaton falure n cables or motor 5 Tel (0) Fax +358 (0)

45 fault tracng vacon 41 Fault code Fault name Possble cause Correctng actons 8 System fault 9 Undervoltage 11 Output phase fault Frequency converter undertemperature Frequency converter overtemperature 15 Motor stalled 16 Motor overtemperature 17 Motor underload Table 5.1: Fault codes component falure faulty operaton The DC-lnk voltage has gone below the nternal safety lmt: most probable cause: supply voltage s too low frequency converter nternal fault Power outages Current measurement has detected that there s no current n one motor phase. Heat snk temperature s under -10 C Heat snk s overheated. Motor stall protecton has trpped. Reset the fault and restart. If the fault re-occurs, contact the dstrbutor near to you. NOTE! If fault F8 occurs, fnd out the subcode of the fault from the Fault Hstory menu under Id xxx! In case of temporary supply voltage break reset the fault and restart the frequency converter. Check the supply voltage. If t s adequate, an nternal falure has occurred. Contact the dstrbutor near to you. Check motor cable and motor. Check the ambent temperature. Check that the coolng ar flow s not blocked. Check the ambent temperature. Make sure that the swtchng frequency s not too hgh n relaton to ambent temperature and motor load. Check that the motor s able to rotate freely. Motor overheatng has been Decrease the motor load. detected by frequency converter If no motor overload motor temperature model. Motor exsts, check the temperature model s overloaded. parameters. Motor underload protecton has trpped. Check motor and load, e.g. for broken belts or dry pumps. 24-hour support +358 (0) Emal: vacon@vacon.com 5

46 42 vacon fault tracng Fault code Fault name Possble cause Correctng actons 22 EEPROM checksum fault 25 Mcrocontroller watchdog fault 27 Back EMF protecton 34 Internal bus communcaton 35 Applcaton fault 41 IGBT Overtemperature 50 Analog nput select 20% - 100% (selected sgnal range 4 to 20 ma or 2 to 10 V) 51 External fault 52 Door Panel fault 53 Feldbus fault 54 Slot fault Table 5.1: Fault codes Parameter save fault faulty operaton component falure faulty operaton component falure Drve has detected that the magnetzed motor s runnng n start stuaton. A rotatng PM-motor Ambent nterference or defectve hardware Applcaton s not workng properly. Overtemperature alarm s ssued when the IGBT swtch temperature exceeds 110 C. Current at the analogue nput s < 4mA; Voltage at the analogue nput s < 2 V. control cable s broken or loose. sgnal source has faled. Dgtal nput fault. Dgtal nput has been programmed as external fault nput and ths nput s actve. Control place s keypad, but door panel has been dsconnected. The data connecton between the feldbus Master and the feldbus of the drve has broken. The connecton between optonal board and API has been broken. Contact the dstrbutor near to you. Reset the fault and restart. If the fault re-occur, contact the dstrbutor near to you. Make sure that there s no rotatng PM-motor when the start command s gven. If the fault re-occur, contact the dstrbutor near to you. Contact the dstrbutor near to you. Check loadng. Check motor sze. Make dentfcaton run. Check the current loop crcutry. Check nstallaton. If nstallaton s correct, contact the nearest Vacon dstrbutor. 5 Tel (0) Fax +358 (0)

47 fault tracng vacon 43 Fault code Fault name Possble cause Correctng actons 55 Wrong run fault Run forward and backward are hgh at the same tme. The drve wll stop and jump Alarm Idenfcaton fault Identfcaton run has faled. Table 5.1: Fault codes Run command was removed before completon of dentfcaton run. Motor s not connected to frequency converter. There s load on motor shaft. 24-hour support +358 (0) Emal: vacon@vacon.com 5

48 44 vacon vacon 20 ap 6. VACON 20 APPLICATION INTERFACE 6.1 Introducton There s only one verson of Control Board avalable for the Vacon 20 drve: Verson Vacon 20 Composton 6 Dgtal nputs 2 Analogue nputs 1 Analogue output 1 Dgtal output 2 Relay outputs RS-485 Interface Table 6.1: Avalable Control Board Ths secton provdes you wth a descrpton of the I / O-sgnals for these versons and nstructons for usng the Vacon 20 general purpose applcaton. The frequency reference can be selected from Preset Speed 0, Keypad, Feldbus, AI1, AI2, AI1+AI2, PID, Motor potentometer and Pulse tran / Encoder. Basc propertes: Dgtal nputs DI1 DI6 are freely programmable. The user can assgn a sngle nput to many functons. Dgtal-, relay- and analogue outputs are freely programmable. Analog output can be programmed as current or voltage output. Analog nput 2 can be programmed as current or voltage nput. DI5/6 can be used as pulse tran or Encoder. Specal features: Programmable Start / Stop and Reverse sgnal logc Motor pre-heat Reference scalng DC-brake at start and stop Programmable U / f curve Adjustable swtchng frequency Autoreset functon after fault 6 Tel (0) Fax +358 (0)

49 vacon 20 ap vacon 45 Protectons and supervsons (all fully programmable; off, alarm, fault): Analog nput low fault External fault Undervoltage fault Earth fault Motor thermal, stall and underload protecton Feldbus communcaton Output phase fault Thermstor fault 8 preset speeds Analogue nput range selecton, sgnal scalng and flterng PID-controller 24-hour support +358 (0) Emal: vacon@vacon.com 6

50 46 vacon vacon 20 ap 6.2 Control I / O 1-10 k Termnal Sgnal Vacon 20 Factory preset Descrpton Vre Ref. voltage out Maxmum load 10 ma 2 AI1 Analog sgnal n 1 Freq. reference P) 0-10 V, R >= 200 k 3 GND I / O sgnal ground 6 24 Vout 24 V output for DI's 20 %, max. load 50 ma 7 DI_C Dgtal Input Commom Dgtal Input Commom for DI1- DI6, refer to Table 6.3 for DI snk type 8 DI1 Dgtal nput 1 Start forward P) V, R > 5 k 9 DI2 Dgtal nput 2 Start reverse P) 10 DI3 Dgtal nput 3 Fault reset P) A A RS485 sgnal A FB Communcaton Negatve B B RS485 sgnal B FB Communcaton Postve 4 AI2 Analog sgnal n 2 Default: 0(4) - 20 ma, R <= 250 PID actual value Other: and Freq. reference 0-10 V, R >= 200 k Selectable through mcroswtch ma 5 GND I / O sgnal ground 13 DO- Dgtal Output Commom Dgtal Output Commom 14 DI4 Dgtal nput 4 Preset speed B0 P) V, R > 5 k As DI, Other: Encoder Input A 15 DI5 Dgtal nput 5 Preset speed B1 P) (frequency up to 10 khz) Selectable through mcroswtch 16 DI6 Dgtal nput 6 External Fault P) As DI, Other: Encoder Input B (frequency up to 10 khz), Pulse Tran Input (frequency up to 5 khz) 0-10 V, RL >1 K 18 AO Analog Output Output frequency P) 0(4) - 20 ma, RL < 500 Selectable through mcroswtch 20 DO Dgtal sgnal out Actve = READY P) Open collector, max. load 48 V / 50 ma Table 6.2: Vacon 20 General purpose applcaton default I / O confguraton and connectons for control board P) = Programmable functon, see parameter lsts and descrptons, chapters 8 and 9. 6 Tel (0) Fax +358 (0)

51 vacon 20 ap vacon 47 Termnal Sgnal Factory preset Descrpton 22 RO 13 Relay out 1 23 RO 14 Actve = RUN P) 0.4 A 24 RO 22 Relay out 2 25 RO 21 Actve = FAULT P) 26 RO 24 Max. swtchng load: 250 Vac / 2 A or 250 Vdc / Max. swtchng load: 250 Vac / 2 A or 250 Vdc / 0.4 A Table 6.2: Vacon 20 General purpose applcaton default I / O confguraton and connectons for control board P) = Programmable functon, see parameter lsts and descrptons, chapters 8 and 9. Termnal Sgnal Factory preset Descrpton 3 GND I / O sgnal ground 6 24 Vout 24 V output for DI's 20 %, max. load 50 ma 7 DI_C Dgtal Input Commom for DI1-DI6 Dgtal Input Commom 8 DI1 Dgtal nput 1 Start forward P) V, R > 5 k 9 DI2 Dgtal nput 2 Start reverse P) 10 DI3 Dgtal nput 3 Fault reset P) 14 DI4 Dgtal nput 4 Preset speed B0 P) V, R > 5 k As DI, Other: Encoder Input A 15 DI5 Dgtal nput 5 Preset speed B1 P) (frequency up to 10 khz) Selectable through mcroswtch 16 DI6 Dgtal nput 6 External Fault P) As DI, Other: Encoder Input B (frequency up to 10 khz), Pulse Tran Input (frequency up to 5 khz) Table 6.3: DI Snk Type, remove jumper J500 and connect the wre usng table 6.3 J500 S4 S3 S2 S1 ON DI Enco Nor AO V ma AI2 V ma RS485 - term Vacon 20 I / O termnals: OFF Fgure 6.1: Mcroswtchs AI2 GND DO- DI4 DI5 DI6 AO DO+ R13 R14 * R VAI1 GND 24V DI-C DI1 DI2 DI3 A B R21 R22 24-hour support +358 (0) Emal: vacon@vacon.com 6

52 48 vacon control panel 7. CONTROL PANEL 7.1 General The panel s an rremovable part of the drve consstng of correspondng control board; The overlay wth dsplay status on the cover and the button are n clarfcatons n the user language. The User Panel conssts of an alphanumerc LCD dsplay wth backlght and a keypad wth the 9 push buttons (see Fgure 7.1). 7.2 Dsplay The dsplay ncludes 14-segment and 7-segment blocks, arrowheads and clear text unt symbols. The arrowheads, when vsble, ndcate some nformaton about the drve, whch s prnted n clear text n user language on the overlay (numbers 1 14 n the fgure below). The arrowheads are grouped n 3 groups wth the followng meanngs and Englsh overlay texts (see Fgure 7.1): Group 1-5; Drve status 1= Drve s ready to start (READY) 2= Drve s runnng (RUN) 3= Drve has stopped (STOP) 4= Alarm condton s actve (ALARM) 5= Drve has stopped due to a fault (FAULT) Group 6-10; Control selectons When API s operated by PC control, there are no arrowhead at I / O, KEYPAD and BUS. 6= Motor s rotatng forward (FWD) 7= Motor s rotatng reverse (REV) 8= I/O termnal block s the selected control place (I / O) 9= Keypad s the selected control place (KEYPAD) 10= Feldbus s the selected control place (BUS) Group 11-14; Navgaton man menu 11= Reference man menu (REF) 12= Montorng man menu (MON) 13= Parameter man menu (PAR) 14= System man menu (SYS) 7 Tel (0) Fax +358 (0)

53 control panel vacon READY RUN STOP ALARM FAULT REF MON PAR SYS FWD REV I/O KEYPAD BUS BACK RESET OK LOC REM 7.3 Keypad Fgure 7.1: Vacon 20 Control panel The keypad secton of the control panel conssts of 9 buttons (see Fgure 7.1). The buttons and ther functons are descrbed as Table 7.1. The drve stops by pressng the keypad STOP button, regardless of the selected control place when Par. 2.7 (Keypad stop button) s 1. If Par. 2.7 s 0, the drve stops by keypad STOP button only when control place s keypad. The drve starts by pressng the keypad START button when the selected control place s KEYPAD or LOCAL control. 24-hour support +358 (0) Emal: vacon@vacon.com 7

54 50 vacon control panel Symbol Button Name Functon Descrpton Start Motor START from the panel STOP Motor STOP from the panel OK OK Used for confrmaton BACK RESET Back / Reset Up and Down Left and Rght Cancels edted parameter Move backwards n menu levels Reset fault ndcaton Navgaton button: Select root parameter number on rootparameter lst, Up decrease / Down ncrease parameter number, Up ncrease / Down decrease parameter value change Avalable n MON, PAR and SYS menuparameter, navgaton and parameter dgt settng MON can also use left and rght button to navgate the menu from V1.x to V2.1 to V3.1 LOC REM Loc / Rem Change control place Table 7.1: Keypad Functon NOTE! The status of all the 9 buttons are avalable for applcaton program! 7 Tel (0) Fax +358 (0)

55 control panel vacon Navgaton on the Vacon 20 control panel Ths chapter provdes you wth nformaton on navgatng the menus on Vacon 20 and edtng the values of the parameters Man menu The menu structure of Vacon 20 control software conssts of a man menu and several submenus. Navgaton n the man menu s shown below: REFERENCE MENU READY RUN STOP ALARM FAULT READY RUN STOP ALARM FAULT REF REF Dspalys the MON MON keypad reference OK value PA R PA R regardless of SYS PRESS SYS the selected Hz Hz contron place. FWD REV I/O KEYPAD BUS FWD REV I/O KEYPAD BUS PRESS MONITORING MENU In ths menu you can browse the montorng values. READY RUN STOP ALARM FAULT READY RUN STO P ALARM FAULT REF MON PA R SYS FWD REV I/O KEYPAD BUS OK REF MON PAR PRESS SYS FWD REV I/O KEYPAD BUS PRESS PARAMETER MENU In ths menu you can browse and edt the parameters. READY RUN STOP ALARM FAULT READY RUN STOP ALARM FAULT REF MON PAR SYS FWD REV I/O KEYPAD BUS OK REF MON PAR PRESS SYS FWD REV I/O KEYPAD BUS PRESS SYSTEM MENU Here you wll be able to browse system parameter and fault submenu. READY RUN STOP ALARM FAULT REF MON PAR SYS FWD REV I/O KEYPAD BUS OK PAR PRESS SYS FWD REV I/O KEYPAD BUS Fgure 7.2: The man menu of Vacon 20 READY RUN STO P ALARM FAU LT REF MON 24-hour support +358 (0) Emal: vacon@vacon.com 7

56 52 vacon control panel Reference menu READY RUN STOP ALARM FAULT REF MON PA R SYS Hz FWD REV I/O KEYPAD BUS OK OK Press to enter edt mode Change value Press to confrm Fgure 7.3: Reference menu dsplay Move to the reference menu wth the UP / DOWN button (see Fgure 7.2). The reference value can be changed by 0.01 every tme wth UP / DOWN button as shown n Fgure 7.3. If the value has bg change, frst press Left and Rght buttons to select the dgt whch has to be changed, then press Up button to ncrease and Down button to decreases the value n the selected dgt. In the end, press OK button to take the settng value effectve. 7 Tel (0) Fax +358 (0)

57 control panel vacon Montorng menu READY RUN STOP ALARM FAULT REF MON PAR SYS READY RUN STOP ALARM FAULT REF MON PAR SYS F WD R EV I/O K EYPAD BUS F WD R EV I/O K EYPAD BUS OK 1 Press OK to enter 2 Montorng menu Press Left/Rght to browse other Montorng groups READY RUN STOP ALARM FAULT REF MON PAR SYS FWD REV I/O KEYPAD BUS READY RUN STOP ALARM FAULT REF MON PAR SYS FWD REV I/O KEYPAD BUS OK 3 Prsess Down to browse V4.5 4 Preess OK the value s dsplayed READY RUN STOP ALARM FAULT REF MON PAR SYS OK 5 Press OK V4.5 s dsplay FWD REV I/O KEYPAD BUS Fgure 7.4: Montorng menu dsplay Montorng values are actual values of measured sgnals as well as status of some control settngs. It s vsble n Vacon 20 dsplay, but t can not be edted. The montorng values are lsted n Table 7.2. Pressng Left/Rght button to change the actual parameter to the frst parameter of the next group, to browse montor menu from V1.x to V2.1 to V3.1 to V4.1. After enterng the desred group, the montorng values can be browsed by pressng UP / DOWN button, as shown n Fgure 7.4. In MON menu the selected sgnal and ts value are alternateng n the dsplay by pressng OK button. Note! Turn on drve power, arrowhead of man menu s at MON, V x.x s dsplayed n Panel. The value of x s determned by the last show before power shut down. E.g., t was V4.5, and t s also V4.5 when restart. 24-hour support +358 (0) Emal: vacon@vacon.com 7

58 54 vacon control panel Code Montorng sgnal Unt ID Descrpton V1.1 Output frequency Hz 1 Output frequency to motor V1.2 Frequency reference Hz 25 Frequency reference to motor control V1.3 Motor speed rpm 2 Calculated motor speed V1.4 Motor current A 3 Measured motor current V1.5 Motor torque % 4 Calculated actual / nomnal torque of the motor V1.6 Output Power KW 79 Output power from drve to motor V1.7 Motor voltage V 6 Motor voltage V1.8 DC-lnk voltage V 7 Measured DC-lnk voltage V1.9 Drve temperature C 8 Heatsnk temperature V1.10 Motor temperature % 9 Calculated motor temperature V1.11 Motor shaft power % 5 Calculated actual / nomnal power of the motor V2.1 Analog nput 1 % 13 AI1 sgnal range n percent of used range V2.2 Analog nput 2 % 14 AI2 sgnal range n percent of used range V2.3 Analog output % 26 AO sgnal range n percent of used range V2.4 Dgtal nput status DI1, DI2, DI3 15 Dgtal nput status V2.5 Dgtal nput status DI4, DI5, DI6 16 Dgtal nput status V2.6 RO1, RO2, DO 17 Relay / dgtal output status V2.7 Pulse tran / encoder nput % % scale value V2.8 Encoder rpm rpm 1235 Scaled accordng to Encoder pulses / revoluton parameter V3.1 Drve Status Word 43 Bt codes status of drve B0 = Ready B1 = Run B2 = Reverse B3 = Fault B6 = RunEnable B7 = AlarmActve B12 = RunRequest B13 = MotorRegulatorActve Table 7.2: Vacon 20 montorng sgnals 7 Tel (0) Fax +358 (0)

59 control panel vacon 55 Code Montorng sgnal Unt ID Descrpton V3.2 Applcaton Status Word 89 Bt codes status of applcaton: B3 = Ramp 2 Actve B5 = Remote CTRL Place 1 actve B6 = Remote CTRL Place 2 actve B7 = Feldbus Control Actve B8 = Local Control Actve B9 = PC Control Actve B10 = Preset Frequences Actve V3.3 DIN Status Word 56 V4.1 PID setpont % 20 Regulator setpont V4.2 PID feedback value % 21 Regulator actual value V4.3 PID error % 22 Regulator error V4.4 PID output % 23 Regulator output V4.5 Process 29 Scaled process varable see par Table 7.2: Vacon 20 montorng sgnals 24-hour support +358 (0) Emal: vacon@vacon.com 7

60 56 vacon control panel Parameter menu In Parameter menu only the Quck setup parameter lst s shown as default. By gvng the value 0 to the parameter 17.2, t s possble to open other advanced parameter groups. The parameter lsts and descrptons can be found n chapters 8 and 9. The followng fgure shows the parameter menu vew: READY RUN STOP ALARM FAULT REF MON PA R SYS READY RUN STOP ALARM FAULT REF MON PA R SYS FWD REV I/O KEYPAD BUS FWD REV I/O KEYPAD BUS OK 1 Press OK to enter Pa r. menu READY RUN STOP ALARM FAULT REF MON PA R SYS FWD REV I/O KEYPAD BUS REF MON PA R SYS 2 Press Rght to browse otherpar. group READY RUN STOP ALARM FAULT FWD REV I/O KEYPAD BUS 3 Press down button to browse P3.4 OK 4 Press OK button to enter edt mode READY RUN STOP ALARM FAULT REF MON PA R SYS OK 6 Press OK to confrm FWD REV I/O KEYPAD BUS 5 Press Up / Down to change value Fgure 7.5: Parameter menu The parameter can be changed as the Fgure 7.5. Left / Rght button s avalable nsde Parameter menu. Pressng Left / Rght button to change the actual parameter to the frst parameter of the next group (Example: any parameter of P1 s dsplayed -> RIGHT button -> P2.1 s dsplayed -> RIGHT button -> P3.1 s dsplayed ). After enterng the desred group, pressng UP / DOWN button to select root parameter number, and then press OK button to dsplay the value of the parameter and also enter edt mode. 7 Tel (0) Fax +358 (0)

61 control panel vacon 57 In edt mode, Left and Rght buttons are used to select the dgt whch has to be changed, and Up ncreases / Down decreases parameter value. In edt mode, the value of Px.x s dsplayed blnkngly n the panel. After about 10 s, Px.x s dsplayed n the panel agan f you don't press any button. Note! In edt mode, f you edt the value and don't press OK button, the value sn't changed successfully. In edt mode, f you don't edt the value, you can press Reset / Back button to dsplay Px.x agan. 24-hour support +358 (0) Emal: vacon@vacon.com 7

62 58 vacon control panel System menu SYS menu ncludng fault submenu and system parameter submenu, and the dsplay and operaton of the system parameter submenu s smlar to PAR menu or MON menu.in system parameter submenu, there are some edtable parameter (P) and some unedtable parameter (V). The Fault submenu of SYS menu ncludes actve fault submenu and fault hstory submenu. READY RUN STOP ALARM FAULT READY RUN STOP ALARM FAULT REF MON PAR SYS REF MON PAR SYS FWD REV I/O KEYPAD BUS FWD REV I/O KEYPAD BUS 1 OK Press OK to enter V1.1 2 Press Left/Rght button to browse other groups READY RUN STOP ALARM FAULT REF MON PAR SYS FWD REV I/O KEYPAD BUS READY RUN STOP ALARM FAULT REF MON PAR SYS FWD REV I/O KEYPAD BUS OK 3 Press down to browse other actve faults 4 Press OK to select one fault to browse ts tme READY RUN STOP ALARM FAULT REF MON PAR SYS 5 Browse for fault code(c xx), subcode(id xx), days(d xx), hours(h xx), mnutes(m xx) FWD REV I/O KEYPAD BUS Fgure 7.6: Fault menu In actve fault stuaton, FAULT arrow s blnkng and the dsplay s blnkng actve fault menu tem wth fault code. If there are several actve faults, you can check t by enterng the actve fault submenu F5.x. F5.1 s always the latest actve fault code. The actve faults can be reset by pressng BACK / RESET button wth long tme (>2 s), when the API s n actve fault submenu level (F5.x). If the fault cannot be reset, the blnkng contnues. It s possble to select other dsplay menus durng actve fault, but n ths case the dsplay returns automatcally to the fault menu f no button s pressed n 10 seconds. The fault code, subcode and the operatng day, hour and mnute values at the fault nstant are shown n the value menu (operatng hours = dsplayed readng). 7 Tel (0) Fax +358 (0)

63 control panel vacon 59 Note! Fault Hstory can be reset by long pressng the BACK / RESET button for 5 second tme,when the API s n fault hstory submenu level (F6.x), t wll also clear all actve faults. See Chapters for fault descrptons 24-hour support +358 (0) Emal: vacon@vacon.com 7

64 60 vacon parameters 8. STANDARD APPLICATION PARAMETERS On the next pages you can fnd the lsts of parameters wthn the respectve parameter groups. The parameter descrptons are gven n Chapter 9. Explanatons: Code: Locaton ndcaton on the keypad; Shows the operator the present Montorng value number or Parameter number Parameter: Name of montorng value or parameter Mn: Mnmum value of parameter Max: Maxmum value of parameter Unt: Unt of parameter value; gven f avalable Default: Factory preset value ID: ID number of the parameter (used wth feldbus control) More nformaton on ths parameter avalable n chapter 9: Param eter descrptons clck on the parameter name. Modfable only n stop state NOTE: On parameter code: Parameter value can only be changed after the FC has been stopped. Ths manual s for Vacon 20 standard applcaton only. If you are usng a specal applcaton, please download the approprate user manual on -> Support & Downloads. 8 Tel (0) Fax +358 (0)

65 parameters vacon Quck setup parameters (Vrtual menu, shows when par = 1) Code Parameter Mn Max Unt Default ID Note Motor nomnal P1.1 voltage Motor nomnal P1.2 frequency Motor nomnal P1.3 speed Motor nomnal P1.4 current Motor cos P1.5 (Power Factor) P1.7 P1.15 P2.1 P2.2 P2.3 P3.1 P3.2 P3.3 Current lmt V Vares ,00 320,00 Hz rpm 0,2 x I Nunt 2,0 x I Nunt 50,00 / 60, / A I Nunt 113 0,30 1,00 0, ,2 x I Nunt 2 x I Nunt Torque boost Remote control place 1 selecton A Check ratng plate on the motor. Check ratng plate on the motor. Default apples for a 4- pole motor. Check ratng plate on the motor. Check ratng plate on the motor. 1.5 x I Nunt 107 Maxmum motor current 0 = Not used 1 = Used 0 = I / O termnal 1 = Feldbus 2 = Keypad Start functon = Ramp 1 = Flyng start Stop functon = Coastng 1 = Ramp Mn frequency 0,00 P3.2 Hz 0, Mnmum freq reference Max frequency P ,00 Hz Remote Control Place 1 frequency reference selecton 50,00 / 60, P3.4 Preset speed 0 P3.1 P3.2 Hz 5, P3.5 Preset speed 1 P3.1 P3.2 Hz 10, Table 8.1: Quck setup parameters Maxmum freq reference 1 = Preset Speeds 0 2 = Keypad 3 = Feldbus 4 = AI1 5 = AI2 6 = PID 7 = AI1 + AI2 8 = Motor potentometer 9 = Pulse tran / Encoder Preset speed 0 s used as frequency reference when P3.3 = 1 Actvated by dgtal nputs 24-hour support +358 (0) Emal: vacon@vacon.com 8

66 62 vacon parameters Code Parameter Mn Max Unt Default ID Note P3.6 Preset speed 2 P3.1 P3.2 Hz 15, P3.7 Preset speed 3 P3.1 P3.2 Hz 20, P4.2 P4.3 Acceleraton tme 1 Deceleraton tme 1 0,1 3000,0 s 3, ,1 3000,0 s 3,0 104 P6.1 AI1 Sgnal range P6.5 AI2 Sgnal range P14.1 P17.2 Automatc reset = Dsable 1 = Enable Parameter conceal Table 8.1: Quck setup parameters Actvated by dgtal nputs Actvated by dgtal nputs Acceleraton tme from 0 Hz to maxmum frequency. Deceleraton tme from maxmum frequency to 0 Hz. 0 = 0-100% 1 = 20% - 100% 20% s the same as 2 V mnmum sgnal level. 0 = 0-100% 1 = 20% - 100% 20% s the same as 2 V or 4 ma mnmum sgnal level. 0 = All parameters vsble 1 = Only quck setup parameter group vsble 8 Tel (0) Fax +358 (0)

67 parameters vacon Motor settngs (Control panel: Menu PAR -> P1) Code Parameter Mn Max Unt Default ID Note P1.1 P1.2 P1.3 Motor nomnal voltage Motor nomnal frequency Motor nomnal speed Motor nomnal P1.4 current Motor cos P1.5 (Power Factor) P1.6 P1.7 P1.8 P1.9 P1.10 P1.11 P1.12 P V Vares ,00 / 30,00 320,00 Hz 60, rpm 1440 / ,2 x I Nunt 2,0 x I Nunt A I Nunt 113 0,30 1,00 0, Check ratng plate on the motor Check ratng plate on the motor Default apples for a 4-pole motor. Check ratng plate on the motor Check ratng plate on the motor Motor type = Inducton 1 = Permanent magnet Current lmt Motor control mode 0,2 x I Nunt 2 x I Nunt A U / f rato Feld weakenng pont Feld weakenng pont voltage U / f md pont frequency U / f md pont voltage 8,00 320,00 Hz 1.5 x I Nunt 107 Maxmum motor current 0 = Frequency control 1 = Open loop speed control 0 = Lnear 1 = Quadratc 2 = Programmable 50,00 / 60, ,00 200,00 % 100, ,00 P1.10 Hz 50,00 / 60, ,00 P1.11 % 100, P1.14 Zero freq voltage 0,00 40,00 % Vares 606 P1.15 P1.16 P1.17 Torque Boost = Dsabled 1 = Enabled Swtchng frequency 1,5 16,0 khz 4,0 / 2,0 601 Brake Chopper Table 8.2: Motor settngs Feld weakenng pont frequency Voltage at feld weakenng pont as % of U nmot Md pont frequency for programmable U / f Md pont voltage for programmable U / f as % of U nmot Voltage at 0 Hz as % of U nmot PWM frequency. If values are hgher than default, reduce the current capacty 0 = Dsabled 1 = Enabled: Always 2 = Run state 24-hour support +358 (0) Emal: vacon@vacon.com 8

68 64 vacon parameters Code Parameter Mn Max Unt Default ID Note P1.18 P1.19 P1.20 P1.21 P1.22 Motor dentfcaton = Not actve 1 = Standstll dentfcaton (need run command wthn 20 s to actvate) Voltage drop over motor wndngs as % of U nmot at nomnal current. 0 = Dsabled 1 = Enabled, Standard mode 2 = Enabled, Shock load mode = Dsable 1 = Enable 0 = Not n use 1 = In use Rs voltage drop 0,00 100,00 % 0, Overvoltage controller Undervoltage controller Sne flter Table 8.2: Motor settngs NOTE! These parameters are shown, when P17.2 = 0. 8 Tel (0) Fax +358 (0)

69 parameters vacon Start / stop setup (Control panel: Menu PAR -> P2) Code Parameter Mn Max Unt Default ID Note P2.1 Remote Control Place 1 Selecton Table 8.3: Start / stop setup = I / O termnals 1 = Feldbus 2 = Keypad P2.2 Start functon = Ramp 1 = Flyng start P2.3 Stop functon = Coastng 1 = Ramp I / O control I / O control sgnal 1 sgnal 2 P2.4 0 Forward Backward I / O Start / Stop Fwd(edge) Inverted Stop logc 2 Fwd(edge) Bwd(edge) 3 Start Reverse 4 Start(edge) Reverse P2.5 Local / Remote = Remote control 1 = Local control P2.6 P2.7 P2.8 Keypad control drecton Keypad stop button Remote Control Place 2 Selecton = Forward 1 = Backward = Keypad control only 1 = Always 0 = I / O termnals = Feldbus 2 = Keypad 24-hour support +358 (0) Emal: vacon@vacon.com 8

70 66 vacon parameters 8.4 Frequency references (Control panel: Menu PAR -> P3) Code Parameter Mn Max Unt Default ID Note P3.1 P3.2 P3.3 Mn frequency 0,00 P3.2 Hz 0, Max frequency P ,00 Hz Remote Control Place 1 frequency reference selecton 50,00 / 60,00 NOTE! These parameters are shown, when P17.2 = = Preset Speeds 0 2 = Keypad 3 = Feldbus 4 = AI1 5 = AI2 6 = PID 7 = AI1+ AI2 8 = Motor potentometer 9 = Pulse tran / Encoder P3.4 Preset speed 0 P3.1 P3.2 Hz 5,00 Preset speed 0 s used as 124 frequency reference when P3.3 = 1 P3.5 Preset speed 1 P3.1 P3.2 Hz 10, Actvated by dgtal nputs P3.6 Preset speed 2 P3.1 P3.2 Hz 15, Actvated by dgtal nputs P3.7 Preset speed 3 P3.1 P3.2 Hz 20, Actvated by dgtal nputs P3.8 Preset speed 4 P3.1 P3.2 Hz 25, Actvated by dgtal nputs P3.9 Preset speed 5 P3.1 P3.2 Hz 30, Actvated by dgtal nputs P3.10 Preset speed 6 P3.1 P3.2 Hz 40, Actvated by dgtal nputs P3.11 Preset speed 7 P3.1 P3.2 Hz 50, Actvated by dgtal nputs P3.12 P3.13 P3.14 Remote Control Place 2 frequency reference selecton Motor Potentonmeter Ramp Motor Potentonmeter Reset Table 8.4: Frequency references As the parameter P Hz/s Speed varaton rate = No Reset 1 = Reset f stopped 2 = Reset f powered down 8 Tel (0) Fax +358 (0)

71 parameters vacon Ramps and brakes setup (Control panel: Menu PAR -> P4) Code Parameter Mn Max Unt Default ID Note P4.1 P4.2 Ramp S-shape 0,0 10,0 s 0, = Lnear >0 = S-curve ramp tme Acceleraton tme 1 0,1 3000,0 s 3,0 103 P4.3 Deceleraton tme 1 0,1 3000,0 s 3,0 104 P4.4 P4.5 Ramp S-shape 2 0,0 10,0 s 0,0 501 Acceleraton tme 2 0,1 3000,0 s 10,0 502 P4.6 Deceleraton tme 2 0,1 3000,0 s 10,0 503 P4.7 P4.8 P4.9 Flux Brakng Flux Brakng Current DC Brakng Current 0,5 x I Nunt 0,3 x I Nunt 2,0 x I Nunt A I Nunt 519 2,0 x I Nunt A I Nunt = Off 1 = Deceleraton 2 = Chopper 3 = Full Mode Defnes the current njected nto the motor durng DC brakeng. P4.10 P4.11 Stop DC current tme Stop DC current frequency 0,00 600,00 s 0, ,10 10,00 Hz 1, Determnes f brakng s ON or OFF and the brakng tme of the DC-brake when the motor s stoppng. 0 = Not actve The output frequency at whch the DC-brakng s appled. P4.12 Start DC current tme 0,00 600,00 s 0, = Not actve P4.13 Accel2 Frequency Threshold 0.00 P3.2 Hz 0, ,00 = dsabled P4.14 Decel2 Frequency Threshold 0,00 P3.2 Hz 0, ,00 = dsabled P4.15 External Brake: Open Delay 0,00 320,00 s 0, Table 8.5: Ramps and brakes setup 24-hour support +358 (0) Emal: vacon@vacon.com 8

72 68 vacon parameters Code Parameter Mn Max Unt Default ID Note P4.16 P4.17 P4.18 P4.19 External Brake: Open Frequency lmt External Brake : Close Frequency lmt External Brake : Close Frequency lmt n Reverse External Brake : Open/Close Current lmt Table 8.5: Ramps and brakes setup 0,00 P3.2 Hz 1, ,00 P3.2 Hz 1, ,00 P3.2 Hz 1, ,0 200,0 % 20, Tel (0) Fax +358 (0)

73 parameters vacon Dgtal nputs (Control panel: Menu PAR -> P5) Code Parameter Mn Max Unt Default ID Note 0 = Not used 1 = DI1 2 = DI2 P5.1 I / O control sgnal = DI3 4 = DI4 5 = DI5 6 = DI6 P5.2 I / O control sgnal As parameter 5.1 P5.3 Reverse As parameter 5.1 P5.4 Ext. fault Close As parameter 5.1 P5.5 Ext. fault Open As parameter 5.1 P5.6 Fault reset As parameter 5.1 P5.7 Run enable As parameter 5.1 P5.8 Preset speed B As parameter 5.1 P5.9 Preset speed B As parameter 5.1 P5.10 Preset speed B As parameter 5.1 Ramp tme 2 selecton P As parameter 5.1 P5.12 Motor potentometer up As parameter 5.1 P5.13 Motor potentometer down As parameter 5.1 P5.14 Remote control Actvates control place place 2 As parameter 5.1 P5.15 Remote control plece freq reference Actvates control place 2 See parameter 5.1 P5.16 PID setpont Actvates reference As parameter 5.1 Actvates the Motor Pre- Heat (DC-Current) n P5.17 Motor PreHeat Actve Table 8.6: Dgtal nputs stop state when parameter Motor Preheat func ton s set to 2 As parameter hour support +358 (0) Emal: vacon@vacon.com 8

74 70 vacon parameters 8.7 Analogue nputs (Control panel: Menu PAR -> P6) Code Parameter Mn Max Unt Default ID Note P6.1 AI1 Sgnal range = 0-100% ( 0-10 V) 1 = 20% - 100% ( 2-10 V) P6.2 AI1 Custom mn -100,00 100,00 % 0, ,00 = no mn scalng P6.3 AI1 Custom max -100,00 300,00 % 100, ,00 = no max scalng P6.4 AI1 flter tme 0,0 10,0 s 0, = no flterng P6.5 AI2 sgnal range = 0-10 V / 0-20 ma = 2-10 V / 4-20 ma P6.6 AI2 Custom mn -100,00 100,00 % 0, ,00 = no mn scalng P6.7 AI2 Custom max -100,00 300,00 % 100, ,00 = no max scalng P6.8 AI2 flter tme 0,0 10,0 s 0, = no flterng Table 8.7: Analogue nputs 8.8 Pulse tran / Encoder (Control panel: Menu PAR -> P7) Code Parameter Mn Max Unt Default ID Note P7.1 Pulse frequency to be Mn pulse frequency Hz nterpreted as a 0% sgnal. P7.2 Pulse frequency to be Max pulse frequency 0, Hz nterpreted as a 100% sgnal. P7.3 Frequency correspondng to 0% f used as fre- Freq. ref. at mn 0,00 P3.2 Hz 0, pulse freq. quency reference. P7.4 Frequency correspondng to 100% f used as Freq. ref. at max 50,00 / 0,00 P3.2 Hz 1232 pulse freq. 60,00 frequency reference. P7.5 0 = Dsable Encoder drecton = Enable / Normal 2 = Enable / Inverted Pulse count of encoder Encoder pulses / per round. Used for scalng encoder rpm montor P ppr revoluton value only. 0 = DI5 and DI6 are for P7.7 normal dgtal nput Confg DI5 and = DI6 s for pulse tran DI6 2 = DI5 and DI6 are for encoder frequence mode Table 8.8: Pulse tran/encoder 8 Tel (0) Fax +358 (0)

75 parameters vacon Dgtal outputs (Control panel: Menu PAR -> P8) Code Parameter Mn Max Unt Default ID Selectons P8.1 RO1 sgnal selecton = Not used 1 = Ready 2 = Run 3 = Fault 4 = Fault Inverted 5 = Warnng 6 = Reversed 7 = At Speed 8 = Motor regulator actve 9 = FB Control Word.B13 10 = FB Control Word.B14 11 = FB Control Word.B15 12 = Output freq superv. 13 = Output torque superv. 14 = Unt temperature superv. 15 = Analogue nput superv. 16 = Preset Speed Actve 17 = External Brake ctrl 18 = Keypad control actve 19 = I / O control actve P8.2 RO2 sgnal selceton As parameter 8.1 P8.3 DO1 sgnal selceton As parameter 8.1 P8.4 RO2 nverson = No nverson 1 = Inverted P8.5 RO2 ON delay 0,00 320,00 s 0, ,00 = No delay P8.6 RO2 OFF delay 0,00 320,00 s 0, ,00 = No delay P8.7 RO1 nverson = No nverson = Inverted P8.8 RO1 ON delay 0,00 320,00 s 0, ,00 = No delay P8.9 RO1 OFF delay 0,00 320,00 s 0, ,00 = No delay P8.10 RO3 sgnal selecton As parameter 8.1, P8.11 RO3-RO5 mplemented but RO4 sgnal hdden untl an opton board selecton s connected. P8.12 RO5 sgnal selecton Table 8.9: Dgtal outputs 24-hour support +358 (0) Emal: vacon@vacon.com 8

76 72 vacon parameters 8.10 Analogue outputs (Control panel: Menu PAR -> P9) Code Parameter Mn Max Unt Default ID Selectons P9.1 P9.2 P9.3 P9.4 P9.5 P9.6 P9.7 P9.8 Analog output sgnal selecton Analog output mnmum Analog output scalng Analog output flter tme Analog output 2 sgnal selecton Analog output 2 mnmum Analog output 2 scalng Analog output flter tme Table 8.10: Analogue outputs = Not used 1 = Output freq. (0-f max ) 2 = Output current (0-I nmotor ) 3 = Motor torque (0-T nmotor ) 4 = PID output (0-100%) 5 = Freq. refer. (0-f max ) 6 = Motor speed (0-n max ) 7 = Motor power (0-P nmotor ) 8 = Motor Voltage (0-U nmotor ) 9 = DC-lnk Voltage ( V) 10 = Process Data In1 ( ) 11 = Process Data In2 ( ) 12 = Process Data In3 ( ) 13 = Process Data In4 ( ) 14 = Test 100% = 0 V / 0 ma 1 = 2 V / 4 ma 0,0 1000,0 % 100,0 311 Scalng factor 0,00 10,00 s 0, Flter tme ,0 1000,0 % 100, ,00 10,00 s 0, As parameter 9.1, AO2&AO3 mplemented but hdden untl an opton board s connected. As parameter 9.2, AO2&AO3 mplemented but hdden untl an opton board s connected. As parameter 9.3, AO2&AO3 mplemented but hdden untl an opton board s connected. As parameter 9.4, AO2&AO3 mplemented but hdden untl an opton board s connected. 8 Tel (0) Fax +358 (0)

77 parameters vacon 73 Code Parameter Mn Max Unt Default ID Selectons P9.9 Analog output 3 sgnal selecton As parameter 9.5 P9.10 Analog output 3 mnmum As parameter 9.6 P9.11 Analog output 3 scalng 0,0 1000,0 % 100,0 483 As parameter 9.7 P9.12 Analog output 3 flter tme 0,00 10,00 s 0, As parameter 9.8 Table 8.10: Analogue outputs 24-hour support +358 (0) Emal: vacon@vacon.com 8

78 74 vacon parameters 8.11 Feldbus Data-Mappng (Control panel: Menu PAR -> P10) Code Parameter Mn Max Unt Default ID Note P10.1 P10.2 P10.3 P10.4 P10.5 P10.6 P10.7 P10.8 P10.9 FB Data Output 1 selecton FB Data Output 2 selecton FB Data Output 3 selecton FB Data Output 4 selecton FB Data Output 5 selecton FB Data Output 6 selecton FB Data Output 7 selecton FB Data Output 8 selecton Aux CW Data In selecton Table 8.11: Feldbus Data-Mappng = Frequency reference 1 = Output reference 2 = Motor speed 3 = Motor current 4 = Motor voltage 5 = Motor torque 6 = Motor power 7 = DC lnk voltage 8 = Actve fault code 9 = Analogue AI1 10 = Analogue AI2 11 = Dgtal nput state 12 = PID feedback value 13 = PID setpont 14 = Pulse tran / encoder nput(%) 15 = Pulse tran / encoder pulse() Varable mapped on PD Varable mapped on PD Varable mapped on PD Varable mapped on PD Varable mapped on PD Varable mapped on PD Varable mapped on PD PDI for Aux CW 0 = Not used 1 = PDI1 2 = PDI2 3 = PDI3 4 = PDI4 5 = PDI5 8 Tel (0) Fax +358 (0)

79 parameters vacon Prohbted Frequences (Control panel: Menu PAR -> P11) Code Parameter Mn Max Unt Default ID Note P11.1 Prohbt Frequency Range 1 Low Lmt P11.2 Prohbt Frequency Range 1 Hgh Lmt P11.3 Prohbt Frequency Range 2 Low Lmt P11.4 Prohbt Frequency Range 2 Hgh Lmt Table 8.12: Prohbted Frequences 0,00 P3.2 Hz 0, ,00 P3.2 Hz 0, ,00 P3.2 Hz 0, ,00 P3.2 Hz 0, Low Lmt 0 = Not used Hgh Lmt 0 = Not used Low Lmt 0 = Not used Hgh Lmt 0 = Not used 8.13 Lmt Supervsons (Control panel: Menu PAR -> P12) Code Parameter Mn Max Unt Default ID Note P12.1 P12.2 P12.3 P12.4 P12.5 P12.6 P12.7 Output freq. supervson functon Output freq. supervson lmt Torque supervson functon Torque supervson lmt Unt Temperature Supervson Unt Temperature Supervson Lmt Analogue nput superv sgnal = Not used = Low lmt 2 = Hgh lmt 0,00 P3.2 Hz 0,00 Output frequency supervson threshold = Not used = Low lmt 2 = Hgh lmt 0,0 300,0 % 0,0 Torque supervson 349 Threshold 0 = Not used = Low lmt 2 = Hgh lmt C 40 Unt temperature supervson threshold = AI1 1 = AI2 P12.8 AI superv ON level 0,00 100,00 % 80, ON threshold AI superv. AI superv OFF P12.9 0,00 100,00 % 40, OFF threshold AI superv. level Table 8.13: Lmt Supervsons 24-hour support +358 (0) Emal: vacon@vacon.com 8

80 76 vacon parameters 8.14 Protectons (Control panel: Menu PAR -> P13) Code Parameter Mn Max Unt Default ID Note P13.1 P13.2 P13.3 P13.4 Analog Input low fault Under voltage fault Earth fault Output Phase Fault 0 = No acton 1 = Alarm 2 = Alarm, preset alarm frequency 3 = Fault: Stop functon 4 = Fault: Coast 1 = No response (no fault generated but drve stll stops modulaton) 2 = Fault:Coast 0 = No acton 1 = Alarm 2 = Fault:Stop functon 3 = Fault:Coast As parameter 13.3 Stall protecton As parameter 13.3 P13.5 P13.6 Under load protecton P13.7 Motor thermal protecton P13.8 Mtp:Ambent temperature P13.9 Mtp:Zero speed coolng Mtp:Thermal tme P13.10 constant P13.11 Stall Current 0, As parameter As parameter C Envronment temperaton 0,0 150,0 % 40,0 706 Coolng as % at 0 speed mn Vares 707 Motor thermal tme constant 2,0 x I Nunt A I Nunt 710 P13.12 Stall tme 0,00 300,00 s 15, Stall tme lmted Stall frequency 0,10 320,00 Hz 25, Stall mn. frequency P13.13 UL:Feld weakenng P13.14 load 10,0 150,0 % 50,0 714 Mnmum torque at feld weakenng P13.15 UL:Zero freq load 5,0 150,0 % 10,0 715 Mnmum torque at F0 P13.16 UL:Tme lmt 1,0 300,0 s 20,0 716 P13.17 Analog Input low fault delay 0,0 10,0 s 0, Table 8.14: Protectons 8 Tel (0) Fax +358 (0)

81 parameters vacon 77 Code Parameter Mn Max Unt Default ID Note P13.18 External fault = No acton 1 = Alarm 2 = Fault: Stop functon 3 = Fault: Coast P13.19 Feldbus fault As parameter 13.1 P13.20 P13.21 Preset alarm frequency Parameters edt lock P3.1 P3.2 Hz 25, P13.22 Thermstor Fault Table 8.14: Protectons Frequency used when fault response s Alarm + preset Frequency. 0 = Edt enabled 1 = Edt dsabled 0 = No acton 1 = Alarm 2 = Fault: Stop functon 3 = Fault: Coast Hdden untl an opton board s connected. NOTE! These parameters are shown, when P17.2 = Fault autoreset parameters (Control panel: Menu PAR -> P14) Code Parameter Mn Max Unt Default ID Note P14.1 Automatc Reset = Dsabled 1 = Enable P14.2 P14.3 Wat tme 0,10 10,00 s 0, Watng tme after fault Tral tme 0,00 60,00 s 30, Maxmum tme for trals P14.4 Trals number Maxmum trals P14.5 Restart Functon = Rampng = Flyng 2 = From Start Functon Table 8.15: Fault autoreset parameters NOTE! These parameters are shown, when P17.2 = hour support +358 (0) Emal: vacon@vacon.com 8

82 78 vacon parameters 8.16 PID control parameters (Control panel: Menu PAR -> P15) Code Parameter Mn Max Unt Default ID Note P15.1 Setpont selecton = Fxed setpont % 1 = AI1 2 = AI2 3 = ProcessDataIn1 (0-100%) 4 = ProcessDataIn2 (0-100%) 5 = ProcessDataIn3 (0-100%) 6 = ProcessDataIn4 (0-100%) 7 = Pulse tran/encoder P15.2 Fxed setpont 1 0,0 100,0 % 50,0 167 Fxed setpont P15.3 Fxed setpont 2 0,0 100,0 % 50,0 168 P15.4 Feedback value selecton Alternatve fxed setpont, selectable wth DI 0 = AI1 1 = AI2 2 = ProcessDataIn1 (0-100%) 3 = ProcessDataIn2 (0-100%) 4 = ProcessDataIn3 (0-100%) 5 = ProcessDataIn4 (0-100%) 6 = AI2-AI1 7 = Pulse tran / encoder P15.5 Feedback value mnumum 0,0 50,0 % 0,0 336 Value at mnmum sgnal P15.6 Feedback value maxmum 10,0 300,0 % 100,0 337 Value at maxmum sgnal P15.7 P gan 0,0 1000,0 % 10, Proportonal gan P15.8 I tme 0,00 320,00 s 10, Integratve tme P15.9 D tme 0,00 10,00 s 0, Dervatve tme P15.10 Error nverson = Drect (Feedback < Setpont ->Increase PID output) 1 = Inverted (Feedback > Setpont ->Decrease PID output) Table 8.16: PID control parameters 8 Tel (0) Fax +358 (0)

83 parameters vacon 79 Code Parameter Mn Max Unt Default ID Note P15.11 Sleep mnmum frequency 0,00 P3.2 Hz 25, Drve goes to sleep mode when the output frequency stays below ths lmt for a tme greater than that defned by parameter Sleep delay P15.12 Sleep delay s Delay for enter sleep P15.13 Wake up error 0,0 100,0 % 5, Threshold for ext sleep P15.14 Sleep setpont boost 0,0 50,0 % 10, Referred to setpont P15.15 Setpont boost tme 0 60 s Boost tme after P15.12 P15.16 P15.17 P15.18 Sleep maxmum loss Sleep loss check tme Process dsplay source select 0,0 50,0 % 5, Referred to feedback value after boost s After boost tme P = PID feedback value 1 = Output frequency 2 = Motor speed 3 = Motor torque 4 = Motor power 5 = Motor current 6 = Pulse Tran / Encoder P15.19 Process dsplay decmal dgts Decmals on dsplay P15.20 Process dsplay maxmum value 0,0 3200,0 100, Process max value Table 8.16: PID control parameters NOTE! These parameters are shown, when P17.2 = hour support +358 (0) Emal: vacon@vacon.com 8

84 80 vacon parameters 8.17 Motor Pre-heat (Control panel: Menu PAR -> P16) Code Parameter Mn Max Unt Default ID Note P16.1 P16.2 Motor Pre-heat Functon Motor Pre-heat Current Table 8.17: Motor Pre-heat = Not used 1 = Always n stop state 2 = Controlled by dgtal nput DC current for Pre-heatng of motor and drve n 0,5 x I A stop state. Actve n stop Nunt state or by dgtal nput whle n stop state Easy usage menu (Control panel: Menu PAR -> P17) Code Parameter Mn Max Unt Default ID Note P17.1 Applcaton Type = Basc 1 = Pump 2 = Fan drve = Hgh Torque NOTE! Vsble only when Startup wzard s actve. P17.2 Parameter conceal Table 8.18: Easy usage menu parameters 0 = All parameters vsble 1 = Only quck setup parameter group vsble 8 Tel (0) Fax +358 (0)

85 parameters vacon System parameters Code Parameter Mn Max Default ID Note Software nformaton (MENU PAR -> V1) V1.1 API SW ID 2314 V1.2 API SW verson 835 V1.3 Power SW ID 2315 V1.4 Power SW verson 834 V1.5 Applcaton ID 837 V1.6 Applcaton revson 838 V1.7 System load 839 When Modbus and no Opton board has been nstalled the comm. Parameters are as follows Status of Modbus communcaton. Format: xx.yyy V2.1 Communcaton status 808 where xx = 0-64 (Number of error messages) yyy = (Number of good messages) P2.2 Feldbus protocol = Not used 1 = Modbus used P2.3 Slave address P2.4 Baud rate P2.6 Party type P2.7 Communcaton tme out P2.8 V2.1 Reset communcaton status = = = = = = = = = = None 1 = Odd 2 = Even 0 = Not used 1 = 1 sec 2 = 2 secs, etc When Canopen board has been nstalled the comm. Parameters are as follows Canopen communcaton status Table 8.19: System parameters hour support +358 (0) Emal: vacon@vacon.com 8

86 82 vacon parameters Code Parameter Mn Max Default ID Note P2.2 Canopen operaton mode P2.3 Canopen Node ID P2.4 Canopen baud rate When DevceNet board has been nstalled the comm. Parameters are as follows V2.1 Communcaton status P2.2 Output assembly type P2.3 MAC ID P2.4 Baud rate P2.5 Input assembly type When ProfBus board has been nstalled the comm. Parameters are as follows V2.1 Communcaton status V2.2 Feldbus protocol V2.3 Actve protocol V2.4 Actve buad rate V2.5 Telegram type P2.6 Operate mode P2.7 Slave address Other nformaton V3.1 MWh counter 827 Mllon Watt Hour V3.2 Power on days 828 V3.3 Power on hours 829 V3.4 Run counter: Days 840 V3.5 Run counter: Hours 841 V3.6 Fault counter 842 V3.7 P4.2 Panel parameter set status montor Restore factory defaults P4.3 Password P4.4 P4.5 P4.6 F5.x F6.x Tme for panel and lcd backlght actve Save parameter set to panel Restore parameter set from panel Actve Fault menu Fault Hstory menu Table 8.19: System parameters Hdden when connect wth PC. 1 = Restores factory defaults for all parameters Hdden when connect wth PC. Hdden when connect wth PC. 8 Tel (0) Fax +358 (0)

87 parameter descrptons vacon PARAMETER DESCRIPTIONS On the next pages you can fnd the descrptons of certan parameters. The descrptons have been arranged accordng to parameter group and number. 9.1 Motor settngs (Control panel: Menu PAR -> P1) 1.7 CURRENT LIMIT Ths parameter determnes the maxmum motor current from the frequency converter. To avod motor overload, set ths parameter accordng to the rated current of the motor. The current lmt s equal to (1.5 x I n ) by default. 1.8 MOTOR CONTROL MODE Wth ths parameter the user can select the motor control mode. The selectons are: 0 = Frequency control: Drve frequency reference s set to output frequency wthout slp compensaton. Motor actual speed s fnally defned by motor load. 1 = Open loop speed control: Drve frequency reference s set to motor speed reference. The motor speed remans the same regardless of motor load. Slp s compensated. 1.9 U / F RATIO There are three selectons for ths parameter: 0 = Lnear: The voltage of the motor changes lnearly wth the frequency n the constant flux area from 0 Hz to the feld weakenng pont where the feld weakenng pont voltage s suppled to the motor. Lnear U / f rato should be used n constant torque applcatons. See Fgure 9.1. Ths default settng should be used f there s no specal need for another settng. 24-hour support +358 (0) Emal: vacon@vacon.com 9

88 84 vacon parameter descrptons 1 = Quadratc: The voltage of the motor changes followng a squared curve form wth the frequency n the area from 0 Hz to the feld weakenng pont where the feld weakenng pont voltage s also suppled to the motor. The motor runs under magnetsed below the feld weakenng pont and produces less torque, power losses and electromechancal nose. Squared U / f rato can be used n applcatons where torque demand of the load s proportonal to the square of the speed, e.g. n centrfugal fans and pumps. U[V] Un Par Default: Nomnal voltage of the motor Feld weakenng pont Lnear Par Squared Default: Nomnal frequency of the motor Par Fgure 9.1: Lnear and squared change of motor voltage f[hz] 2 = Programmable U / f curve: The U / f curve can be programmed wth three dfferent ponts. Programmable U / f curve can be used f the other settngs do not satsfy the needs of the applcaton. 9 Tel (0) Fax +358 (0)

89 parameter descrptons vacon 85 U[V] Un Par Default: Nomnal voltage of the motor Feld weakenng pont Par (Def. 50%) Par (Def. 0.0%) Par (Def. 10%) Par Fgure 9.2: Programmable U / f curve Default: Nomnal frequency of the motor f[hz] 1.10 FIELD WEAKENING POINT The feld weakenng pont s the output frequency at whch the output voltage reaches the value set wth par FIELD WEAKENING POINT VOLTAGE Above the frequency at the feld weakenng pont, the output voltage remans at the value set wth ths parameter. Below the frequency at the feld weakenng pont, the output voltage depends on the settng of the U / f curve parameters. See parameters and Fgures 9.1 and 9.2. When the parameters 1.1 and 1.2 (nomnal voltage and nomnal frequency of the motor) are set, the parameters 1.10 and 1.11 are automatcally gven the correspondng values. If you need dfferent values for the feld weakenng pont and the voltage, change these parameters after settng the parameters 1.1 and U / F MIDDLE POINT FREQUENCY If the programmable U / f curve has been selected wth the parameter 1.9, ths parameter defnes the mddle pont frequency of the curve. See Fgure U / F MIDDLE POINT VOLTAGE If the programmable U / f curve has been selected wth the parameter 1.9, ths parameter defnes the mddle pont voltage of the curve. See Fgure ZERO FREQUENCY VOLTAGE Ths parameter defnes the zero frequency voltage of the curve. See Fgures 9.1 and hour support +358 (0) Emal: vacon@vacon.com 9

90 86 vacon parameter descrptons 1.15 TORQUE BOOST When ths parameter has been actvated, the voltage to the motor changes automatcally wth hgh load torque whch makes the motor produce suffcent torque to start and run at low frequences. The voltage ncrease depends on the motor type and power. Automatc torque boost can be used n applcatons wth hgh load torque, e.g. n conveyors. 0 = Dsabled 1 = Enabled Note: In hgh torque - low speed applcatons - t s lkely that the motor wll overheat. If the motor has to run a prolonged tme under these condtons, specal attenton must be pad to coolng the motor. Use external coolng for the motor f the temperature tends to rse too hgh. Note: The best performance can be reached by runnng motor dentfcaton, see par SWITCHING FREQUENCY Motor nose can be mnmsed usng a hgh swtchng frequency. Increasng the swtchng frequency reduces the capacty of the frequency converter unt. Swtchng frequency for Vacon 20: khz BRAKE CHOPPER Note! An nternal brake chopper s nstalled n three phase supply MI2 and MI3 sze drves. 0 = Dsable (No brake chopper used) 1 = Enable: Always (Used n Run and Stop state) 2 = Enable: Run state (Brake chopper used n Run state) When the frequency converter s deceleratng the motor, the energy stored to the nerta of the motor and the load are fed nto an external brake resstor, f the brake chopper has been actvated. Ths enables the frequency converter to decelerate the load wth a torque equal to that of acceleraton (provded that the correct brake resstor has been selected). See separate Brake resstor nstallaton manual MOTOR IDENTIFICATION 0 = Not actve 1 = Standstll dentfcaton When Standstll dentfcaton s selected, the drve wll perform an ID-run when t s started from selected control place. Drve has to be started wthn 20 seconds, otherwse dentfcaton s aborted. 9 Tel (0) Fax +358 (0)

91 parameter descrptons vacon 87 The drve does not rotate the motor durng Standstll dentfcaton. When ID run s ready the drve s stopped. Drve wll start normally, when the next start command s gven. After end the dentfcaton, the drve need stop the start command. If control place s Keypad, user need press stop button. If control place s IO,user need put DI(Control sgnal) nactvate. If control place s feldbus, user need set the control bt to 0. The ID run mproves the torque calculatons and the automatc torque boost functon. It wll also result n a better slp compensaton n speed control (more accurate RPM). The parameters below wll change after ID run successfully, a. P1.9 U / f rato b. P1.12 U / f md pont frequency c. P1.13 U / f md pont voltage d. P1.14 Zero freq voltage e. P1.18 Motor dentfcaton (1->0) f. P1.19 Rs voltage drop Note!The nameplate data of the motor has to be set BEFORE dong ID run. 24-hour support +358 (0) Emal: vacon@vacon.com 9

92 88 vacon parameter descrptons 9.2 Start / stop setup (Control panel: Menu PAR -> P2) 2.1 REMOTE CONTROL PLACE 1 SELECTION Wth ths parameter, the user can select the actve control place. The selectons are: 0 = I / O termnal (frequency reference can be selected wth P3.3) 1 = Feldbus 2 = Keypad The prorty order of selectng the control place s 1. PC control from Vacon lve operaton wndow 2. Loc / Rem button 3. Forced from I / O termnal Note: You can select control place by pressng Loc / Rem button or wth par. 2.5(Local / Remote), P2.1 wll have no effect n local mode. Local = Keyp ad s the control place Remote = I / O termnal or FeldBus 2.2 START FUNCTION The user can select two start functons for Vacon 20 wth ths parameter: 0 = Ramp start The frequency converter starts from 0 Hz and accelerates to the set frequency reference wthn the set acceleraton tme (See detaled descrpton: ID103). (Load nerta, torque or startng frcton may cause prolonged acceleraton tmes). 1 = Flyng start Wth ths functon the drve dentfes the speed of the motor and starts to the correspondng frequency mmedately. Use ths mode f the motor s rotatng when the start command s gven. Wth the flyng start, t s possble to rde through short mans voltage nterruptons. 2.3 STOP FUNCTION Two stop functons can be selected n ths applcaton: 0 = Coastng The motor coasts to a halt wthout control from the frequency converter after the Stop command. 1 = Rampng 9 Tel (0) Fax +358 (0)

93 parameter descrptons vacon 89 After the Stop command, the speed of the motor s decelerated accordng to the set deceleraton parameters. If the regenerated energy s hgh t may be necessary to use an external brakng resstor for to be able to decelerate the motor n acceptable tme. 2.4 I / O START STOP LOGIC Values offer possbltes to control the startng and stoppng of the AC drve wth dgtal sgnal connected to dgtal nputs. CS = Control sgnal. The selectons ncludng the text 'edge' shall be used to exclude the possblty of an unntentonal start when, for example, power s connected, re-connected after a power falure, after a fault reset, after the drve s stopped by Run Enable (Run Enable = False) or when the control place s changed to I / O control. The Start / Stop contact must be opened before the motor can be started. Accurate stop mode s that the stop tme s fxed from fallng edge of DI to motor stop. Selecton number 0 Selecton name CS1:Forward CS2:Backward Note The functons take place when the contacts are closed. FWD Output frequency Set frequency 0 Hz t Set frequency REV Run enable Ctrl sgnal 1 Ctrl sgnal 2 Keypad start button Keypad stop button Fgure 9.3: Start/Stop logc, selecton 0 24-hour support +358 (0) Emal: vacon@vacon.com 9

94 90 vacon parameter descrptons Explanatons 1 Control sgnal (CS) 1 actves causng the output frequency to rse. The motor runs forward. 2 If start forward sgnal [CS1] and start reverse sgnal [CS2] are actve smultaneously, there s alarm55 n LCD panel and motor should be stopped. 3 CS1 s nactvated whch caused the drecton to start changng (FWD to REV) because CS2 s stll actve, and Alarm 55 should be dsappeared n a whle tme. 4 CS2 nactvates and the frequency fed to the motor drops to 0. 5 CS2 actves agan causng the motor to accelerate (REV) towards the set frequency. 6 CS2 nactvates and the frequency fed to the motor drops to 0. 7 CS1 actves and the motor accelerates (FWD) towards the set frequency. 8 Run enable sgnal s set to FALSE, whch drops the frequency to 0.The run enable sgnal s confgured wth par Run enable sgnal s set to TRUE, whch causes the frequency to rse towards the set frequency because CS1 s stll actve. 10 Keypad stop button s pressed and the frequency fed to the motor drops to 0.(Ths sgnal only works f Par. 2.7 [Keypad stop button] = 1) 11 The drve starts through pushng the Start button on the keypad. 12 The keypad stop button s pushed agan to stop the drve. (Ths sgnal only works f Par. 2.7 [Keypad stop button] = 1) 13 The attempt to start the drve through pushng the Start button s not successful because CS1 s nactve. 9 Tel (0) Fax +358 (0)

95 parameter descrptons vacon 91 Selecton number 1 Selecton name CS1:Forward(edge) CS2:Inverted stop Note FWD Output frequency Set frequency 0 Hz t Set frequency REV Run enable Ctrl sgnal 1 Ctrl sgnal 2 Keypad stop button Fgure 9.4: Start/Stop logc, selecton 1 Explanatons 1 Control sgnal (CS) 1 actves causng the output frequency to rse. The motor runs forward. 2 CS2 nactvates causng the frequency to drop to 0. 3 CS1 nactvates causng the output frequency to rse agan. The motor runs forward. 4 Run enable sgnal s set to FALSE, whch drops the frequency to 0. The run enable sgnal s confgured wth par Start attempt wth CS1 s not successful because Run enable sgnal s stll FALSE. 6 CS1 actvates and the motor accelerates (FWD) towards the set frequency because the Run enable sgnal has been set to TRUE. 7 Keypad stop button s pressed and the frequency fed to the motor drops to 0.(Ths sgnal only works f Par.2.7 [Keypad stop button] = 1) 8 CS1 actvates causng the output frequency to rse agan. The motor runs forward. 9 CS2 nactvates causng the frequency to drop to hour support +358 (0) Emal: vacon@vacon.com 9

96 92 vacon parameter descrptons Selecton number 2 Selecton name CS1:Forward(edge) CS2:Backward(edge) Note Shall be used to exclude the possblty of an unntentonal start. The Start / Stop contact must be opened before the motor can be restarted. FWD Output frequency Set frequency 0 Hz t Set frequency REV Run enable Ctrl sgnal 1 Ctrl sgnal 2 Keypad stop button Fgure 9.5: Start/Stop logc, selecton 2 Explanatons: 1 Control sgnal (CS) 1 actves causng the output frequency to rse. The motor runs forward. 2 If start forward sgnal [CS1] and start reverse sgnal [CS2] are actve smultaneously, there s alarm55 n LCD panel and motor should be stopped. 3 CS1 s nactvated the motor s stll stopped though CS2 s stll actve, and Alarm 55 should be dsappeared n a whle tme. 4 CS2 actvates agan causng the motor to accelerate (REV) towards the set frequency. 5 CS2 nactvates and the frequency fed to the motor drops to 0. 6 CS1 actvates and the motor accelerates (FWD) towards the set frequency. 7 Run enable sgnal s set to FALSE, whch drops the frequency to 0.The run enable sgnal s confgured wth par CS1 actvates agan causng the motor to accelerate (REV) towards the set frequency. 9 Keypad stop button s pressed and the frequency fed to the motor drops to 0.(Ths sgnal only works f Par.2.7 [Keypad stop button] = 1) 10 CS1 actvates agan causng the motor to accelerate (REV) towards the set frequency. 11 CS1 nactvates and the frequency fed to the motor drops to 0. 9 Tel (0) Fax +358 (0)

97 parameter descrptons vacon 93 Selecton number 3 Selecton name CS1:Start CS2:Reverse Note FWD Output frequency Set frequency 0 Hz t Set frequency REV Run enable Ctrl sgnal 1 Ctrl sgnal 2 Keypad start button Keypad stop button Fgure 9.6: Start/Stop logc, selecton 3 Explanatons: 1 Control sgnal (CS) 1 actves causng the output frequency to rse. The motor runs forward. 2 CS2 actvates whch causes the drecton to start changng (FWD to REV). 3 CS2 s nactvated whch causes the drecton to start changng (REV to FWD) because CS1 s stll actve. 4 Also CS1 nactvates and the frequency drops to 0. 5 Despte the actvates of CS2,the motor does not start because CS1 s nactve. 6 CS1 actvates causng the output frequency to rse agan. The motor runs forward because CS2 s nactve. 7 Run enable sgnal s set to FALSE, whch drops the frequency to 0.The run enable sgnal s confgured wth par Run enable sgnal s set to TRUE, whch causes the frequency to rse towards the set frequency because CS1 s stll actve. 9 Keypad stop button s pressed and the frequency fed to the motor drops to 0.(Ths sgnal only works f Par.2.7 [Keypad stop button] = 1) 10 The drve starts through pushng the Start button on the keypad. 11 The drve s stopped agan wth the Stop button on the Keypad. 12 The attempt to start the drve through pushng the Start button s not successful because CS1 s nactve. 24-hour support +358 (0) Emal: vacon@vacon.com 9

98 94 vacon parameter descrptons Selecton number 4 Selecton name CS1:Start(edge) CS2:Reverse Note Shall be used to exclude the possblty of an unntentonal start. The Start / Stop contact must be opened before the motor can be restarted. FWD Output frequency Set frequency 0 Hz t Set frequency REV Run enable Ctrl sgnal 1 Ctrl sgnal 2 Keypad stop button Fgure 9.7: Start/Stop logc, selecton 4 Explanatons: 1 Control sgnal (CS) 1 actves causng the output frequency to rse. The motor runs forward because CS2 s nactve.. 2 CS2 actvates whch causes the drecton to start changng (FWD to REV). 3 CS2 s nactvated whch causes the drecton to start changng (REV to FWD) because CS1 s stll actve. 4 Also CS1 nactvates and the frequency drops to 0. 5 Despte the actvaton of CS2, the motor does not start because CS1 s nactve. 6 CS1 actvates causng the output frequency to rse agan. The motor runs forward because CS2 s nactve. 7 Run enable sgnal s set to FALSE, whch drops the frequency to 0.The run enable sgnal s confgured wth par Before a successful start can take place, CS1 must be opened and closed agan. 9 Keypad stop button s pressed and the frequency fed to the motor drops to 0.(Ths sgnal only works f Par.2.7 [Keypad stop button] = 1) 10 Before a successful start can take place, CS1 must be opened and closed agan. 11 CS1 nactvates and the frequency drops to 0. 9 Tel (0) Fax +358 (0)

99 parameter descrptons vacon LOCAL / REMOTE Ths parameter defnes whether the control place of the drve s remote (I / O or FeldBus) or local. 0 = Remote Control 1 = Local Control The prorty order of selectng control place s 1. PC control from Vacon lve operaton wndow 2. Loc / Rem button 3. Forced from I / O termnal 24-hour support +358 (0) Emal: vacon@vacon.com 9

100 96 vacon parameter descrptons 9.3 Frequency references (Control panel: Menu PAR -> P3) 3.3 REMOTE CONTROL PLACE 1 FREQUENCY REFERENCE SELECTION It defnes the selected frequency reference source when the drve s controlled by the I / O termnal. A second reference source s programmable n par = Preset speed 0 2 = Keypad reference 3 = Feldbus Reference 4 = AI1 5 = AI2 6 = PID 7 = AI1+AI2 8 = Motor potentometer 9 = Pulse tran / Encoder PRESET SPEEDS 0-7 Preset speed 0 s used as frequency reference when P3.3 = 1. Preset speeds 1-7 can be used to determne frequency references that are appled when approprate combnatons of dgtal nputs are actvated. Preset speeds can be actvated from dgtal nputs despte of the actve control place. Parameter values are automatcally lmted between the mnmum and maxmum frequences. (par. 3.1, 3.2). Speed Preset speed B2 Table 9.1: Preset speeds 1-7 Preset speed B1 Preset speed B0 x Preset speed 1 Preset speed 2 x Preset speed 3 x x Preset speed 4 x Preset speed 5 x x Preset speed 6 x x Preset speed 7 x x x 9 Tel (0) Fax +358 (0)

101 parameter descrptons vacon MOTOR POTENTIOMETER RAMP 3.14 MOTOR POTENTIOMETER RESET P3.13 s the speed varaton ramp when motor potentometer reference s ncreased or decreased. P3.14 tells under whch crcumstances the potentometers reference should be reset and start over from 0 Hz. 0 = No reset 1 = Reset at stop and power down 2 = Reset at power down P5.12 and P5.13 sets whch dgtal nputs ncrease and decrease the motor potentometers reference. Frequency Reference y/x = P Motor potentometer ramp P Mn Frequency P Max Frequency x y I/O Motor potentometer up tme I/O Motor potentometer down Fgure 9.8: The change of motor potentometers reference 24-hour support +358 (0) Emal: vacon@vacon.com 9

102 98 vacon parameter descrptons 9.4 Ramps & brakes setup (Control panel: Menu PAR -> P4) 4.1 RAMP S-SHAPE The start and end of the acceleraton and deceleraton ramp can be smoothed wth ths parameter. Settng value 0 gves a lnear ramp shape whch causes acceleraton and deceleraton to act mmedately to the changes n the reference sgnal. Settng value seconds for ths parameter produces an S-shaped acceleraton/deceleraton. The acceleraton and deceleraton tmes are determned wth parameters 4.2 and 4.3. [Hz] P4.2, 4.3 P4.1 P4.1 [t] Fgure 9.9: S-shaped acceleraton/deceleraton 4.2 ACCELERATION TIME DECELERATION TIME RAMP S-SHAPE ACCELERATION TIME DECELERATION TIME 2 These lmts correspond to the tme requred for the output frequency to accelerate from the zero frequency to the set maxmum frequency, or to decelerate from the set maxmum frequency to zero frequency. The user can set two dfferent acceleraton/deceleraton tme and set two dfferent ramp s-shape for one applcaton.the actve set can be selected wth the selected dgtal nput (par. 5.11). 4.7 FLUX BRAKING Instead of DC brakng, flux brakng s a useful form of brakng wth motors of max. 15 kw. 9 Tel (0) Fax +358 (0)

103 parameter descrptons vacon 99 When brakng s needed, the frequency s reduced and the flux n the motor s ncreased, whch n turn ncreases the motor's capablty to brake. Unlke DC brakng, the motor speed remans controlled durng brakng. 0 = Off 1 = Deceleraton 2 = Chopper 3 = Full Mode Note: Flux brakng converts the energy nto heat at the motor, and should be used ntermttently to avod motor damage STOP DC CURRENT TIME Determnes f brakng s ON or OFF and the brakng tme of the DC-brake when the motor s stoppng. The functon of the DC-brake depends on the stop functon, par = DC brake s not actve >0 = DC brake s actve and ts functon depends on the Stop functon, (par. 2.3). The DC brakng tme s determned wth ths parameter. Par. 2.3 = 0 (Stop functon = Coastng): After the stop command, the motor coasts to a stop wthout control from the frequency converter. Wth the DC njecton, the motor can be electrcally stopped n the shortest possble tme, wthout usng an optonal external brakng resstor. The brakng tme s scaled by the frequency when the DC-brakng starts. If the frequency s greater, or equal to the nomnal frequency of the motor, the set value of parameter 4.10 determnes the brakng tme. For example, when the frequency s 10% of the nomnal, the brakng tme s 10% of the set value of parameter hour support +358 (0) Emal: vacon@vacon.com 9

104 100 vacon parameter descrptons fout fout fn Output frequency Motor speed fn DC-brakng ON 0,1 x fn Output frequency Motor speed t=1xpar.4.10 t DC-brakng ON t=0,1x par.4.10 t RUN STOP RUN STOP Fgure 9.10: DC-brakng tme when Stop mode = Coastng Par. 2.3 = 1 (Stop functon = Ramp): After the Stop command, the speed of the motor s reduced accordng to the set deceleraton parameters, f the nerta of the motor and load allows that, to the speed defned wth parameter 4.11, where the DC-brakng starts. The brakng tme s defned wth parameter See Fgure fout Motor speed Output frequency Par DC-brakng RUN STOP t t=par Fgure 9.11: DC-brakng tme when Stop mode = Ramp 9 Tel (0) Fax +358 (0)

105 parameter descrptons vacon STOP DC CURRENT FREQUENCY It s the output frequency at whch the DC-brakng s appled START DC CURRENT TIME DC-brake s actvated when the start command s gven. Ths parameter defnes the tme of the DC-brakng. After the brake s released, the output frequency ncreases accordng to the set start functon by par DC-brakng current Output frequency Par 4.9 RUN STOP Par4.12 t Fgure 9.12: DC brakng tme at start 4.15 EXTERNAL BRAKE: OPEN DELAY 4.16 EXTERNAL BRAKE: OPEN FREQUENCY LIMIT 4.17 EXTERNAL BRAKE: CLOSE FREQUENCY LIMIT 4.18 EXTERNAL BRAKE: CLOSE FREQUENCY LIMIT IN REVERSE 4.19 EXTERNAL BRAKE: OPEN / CLOSE CURRENT LIMIT External brake control s used for controllng a mechancal brake on the motor by dgtal / relay output by selectng value 12 for parameters P8.1, P8.2 or P8.3. Brake s closed whle relay s open and vce versa. Openng brake condtons: There are three dfferent condtons for openng the brake, all must be true, f used. 1. The Open frequency lmt (P4.16) must be reached. 2. When the Openng frequency lmt has been reached the Open delay (P4.15) must also elapse. Note! The output frequency s held at the Open frequency lmt untl ths. 3. When the two prevous condtons are reached. The brake wll open f the output current s hgher than the current lmt.(p4.19) 24-hour support +358 (0) Emal: vacon@vacon.com 9

106 102 vacon parameter descrptons Notce that any of the prevous condtons can be left out by settng ther values to zero. Output Frequency 1 2 Actual Reference P Open Frequency Lmt P Open delay Tme External Brake Brake closed Relay open 3 Brake open Relay closed 1 = Open frequency Lmt reached 2 = Open delay elapsed 3 = Brake opens f External Brake:Current lmt s exceeded. Fgure 9.13: Startng / openng sequence wth external brake Closng brake condtons: There are 2 condtons for closng the brake agan. It s enough that one s true for the brake to close. 1. If there s no run command actve and output frequency goes below Close frequency lmt (P4.17) or Close frequency lmt n reverse (P4.18), dependng on drecton of rotaton. OR 2. Output current has gone below Current lmt.(p4.19) 9 Tel (0) Fax +358 (0)

107 parameter descrptons vacon Dgtal nputs (Control panel: Menu PAR -> P5) These parameters are programmed usng the FTT-method (Functon To Termnal), where you have a fxed nput or output that you defne a certan functon for. You can also defne more than one functon to a dgtal nput, e.g. Start sgnal 1 and Preset Speed B1 to DI1. The selectons for these parameters are: 0 = Not used 1 = DI1 2 = DI2 3 = DI3 4 = DI4 5 = DI5 6 = DI6 5.1 I / O CTRL SIGNAL I / O CTRL SIGNAL 2 P5.1 and P5.2 : See P2.4 (I/O start stop logc) for functon 5.3 REVERSE The dgtal nput only actve when P2.4 (I/O Start stop logc) =1 The motor wll run n reverse when the rsng edge of P5.3 s happened. 5.4 EXTERNAL FAULT CLOSE 5.5 EXTERNAL FAULT OPEN 5.6 FAULT RESET 5.7 RUN ENABLE 5.8 PRESET SPEED B0 5.9 PRESET SPEED B PRESET SPEED B RAMP TIME 2 SELECTION Contact open: Acceleraton / Deceleraton tme 1 and Ramp S-shape selected Contact closed: Acceleraton / Deceleraton tme 2 and Ramp S-shape2 selected Set Acceleraton / Deceleraton tmes wth parameters 4.2 and 4.3 and the alternatve ramp tmes wth 4.4 and 4.5. Set Ramp S-shape wth Par. 4.1 and the alternatve Ramp S-shape2 wth Par MOTOR POTENTIOMETER UP 5.13 MOTOR POTENTIOMETER DOWN 5.14 REMOTE CONTROL PLACE 2 24-hour support +358 (0) Emal: vacon@vacon.com 9

108 104 vacon parameter descrptons 5.15 REMOTE CONTROL PLECE FREQ REFERENCE PID SETPOINT 2 Dgtal nput hgh actvates setpont 2 (P15.3), when P15.1= MOTOR PREHEAT ACTIVE Dgtal nput hgh actvates the Motor preheat functon (f P16.1 = 2) whch feeds DC-Current to the motor n stop state. 9.6 Analogue nputs (Control panel: Menu PAR -> P6) 6.4 AI1 FILTER TIME 6.8 AI2 FILTER TIME Ths parameter, gven a value greater than 0, actvates the functon that flters out dsturbances from the ncomng analogue sgnal. Long flterng tme makes the regulaton response slower. See Fgure % Unfltered sgnal 100% 63% Fltered sgnal Par. 6.4 Par. 6.8 t[s] Fgure 9.14: AI1 and AI2 sgnal flterng 6.2 AI1 CUSTOM MINIMUM 6.3 AI1 CUSTOM MAXIMUM 6.6 AI2 CUSTOM MINIMUM 6.7 AI2 CUSTOM MAXIMUM These parameters set the analogue nput sgnal for any nput sgnal span from -100 to 100%. 9 Tel (0) Fax +358 (0)

109 parameter descrptons vacon Pulse tran / Encoder (Control panel: Menu PAR -> P7) 7.1 MIN PULSE FREQUENCY 7.2 MAX PULSE FREQUENCY Mnmum and maxmum pulse frequency correspond to a sgnal value of 0% and 100% respectvely. Frequences over Max pulse frequency are handled as constant 100% and below Mn pulse frequency as constant 0%. The sgnal value of range 0-100% s shown n montor value V2.7 and can be used as PID Controller feedback, or scaled to frequency wth parameters P7.3 and P7.4, and used as frequency reference. 7.3 FREQ REF AT MIN PULSE FREQUENCY 7.4 FREQ REF AT MAX PULSE FREQUENCY Pulse tran/encoder sgnal wth range 0-100% and scaled by parameter P7.1 and P7.2, whch can be used as frequency reference by tellng what frequency corresponds to 0% and 100% wth parameters P7.3 and P7.4 respectvely. Then t can be selected as frequency reference for Remote control place. 7.5 ENCODER DIRECTION It s possble to also take drecton nformaton from the encoder. 0 = Dsable 1= Enable/Normal 2 = Enable/Inverted 7.6 ENCODER PULSES / REVOLUTION Encoder pulses per revoluton can be set n case an encoder s used, whch s used to record the count of encoder per round. In ths case montor value V2.8 wll show the actual rpm of the encoder. Maxmum pulse frequency s 10 khz. It means that a 256 pulse per round encoder would allow shaft speeds up to 2300 rpm. (60*10000/256 = 2343) 7.7 CONFIG DI5 AND DI6 0 = DI5 and DI6 are for normal dgtal nput 1 = DI6 s for pulse tran 2 = DI5 and DI6 are for encoder frequency mode When usng pulse tran / encoder nput, the DI5 and DI6 has to be set to - Not Used 24-hour support +358 (0) Emal: vacon@vacon.com 9

110 106 vacon parameter descrptons 9.8 Dgtal outputs (Control panel: Menu PAR -> P8) 8.1 RO1 SIGNAL SELECTION 8.2 RO2 SIGNAL SELCETION 8.3 DO1 SIGNAL SELCETION Settng Table 9.2: Output sgnals va RO1, RO2 and DO1 Sgnal content 0 = Not used Output s not n operaton. 1 = Ready The frequency converter s ready to operate. 2 = Run The frequency converter operates (motor s runnng). 3 = Fault A fault trp has occurred. 4 = Fault nverted A fault trp has not occurred. 5 = Warnng A warnng s actve. 6 = Reversed The reverse command has been selected, output frequency to the motor s negatve. 7 = At speed The output frequency has reached the set reference. 8 = Motor regulator actve 9 = FB Control Word.B13 10 = FB Control Word.B14 11 = FB Control Word.B15 12 = Output frequency superv. 13 = Output torque superv. 14 = Unt temperature superv. 15 = Analogue nput superv. Each of motorng current regulator,generatng current reg.,over voltage reg.,under voltage reg. s actve. Output can be controlled wth B13 n the feldbus control word. Output can be controlled wth B14 n the feldbus control word. Output can be controlled wth B15 n the feldbus control word. Output frequency s over / under the lmts, set wth parameters P12.1 and P12.2. Motor torque s over/under the lmt, se t wth parameter P12.3 and P12.4 Unt temperature s over / under the lmts, set wth parameters P12.5 and P12.6. Analogue nputs set wth parameter P12.7 s over / under the lmts, set n P12.8 and P = Preset Speed Actve Preset speeds are actvated through dgtal nputs. 17 = External Brake control External Brake control. Closed = Brake open, Open = Brake closed. 18 = Keypad control actve Keypad s set as the current control place. 19 = I / O control actve I / O s set as the current control place. 9 Tel (0) Fax +358 (0)

111 parameter descrptons vacon Analogue outputs (Control panel: Menu PAR -> P9) 9.1 ANALOG OUTPUT SIGNAL SELECTION 0 = Not used 1 = Output frequency (0 - f max ) 2 = Output current (0 - I nmotor ) 3 = Motor torque (0 - T nmotor ) 4 = PID output (0-100%) 5 = Frequency reference (0 - f max ) 6 = Motor speed (0 - n max ) 7 = Motor power (0 - P nmotor ) 8 = Voltage (0 - U nmotor ) 9 = DC-lnk Voltage (0-1000V) 10 = Process Data In1 ( ) 11 = Process Data In2 ( ) 12 = Process Data In3 ( ) 13 = Process Data In4 ( ) 14 = Test 100% 9.2 ANALOG OUTPUT MINIMUM 0 = 0 V / 0 ma 1 = 2 V / 4 ma 24-hour support +358 (0) Emal: vacon@vacon.com 9

112 108 vacon parameter descrptons 9.10 Feldbus Data-Mappng (Control panel: Menu PAR -> P10) 10.1 FB DATA OUT 1 SELECTION Parameter couples read only varables to output process data 1. 0 = Frequency reference 1 = Output reference 2 = Motor speed 3 = Motor current 4 = Motor voltage 5 = Motor torque 6 = Motor power 7 = DC lnk voltage 8 = Actve fault code 9 = Analogue AI1 10 = Analogue AI2 11 = Dgtal nput state 12 = PID feedback value 13 = PID setpont 14 = Pulse tran / encoder nput(%) 15 = Pulse tran / encoder pulse() 10.2 FB DATA OUT 2 SELECTION 10.3 FB DATA OUT 3 SELECTION 10.4 FB DATA OUT 4 SELECTION 10.5 FB DATA OUT 5 SELECTION 10.6 FB DATA OUT 6 SELECTION 10.7 FB DATA OUT 7 SELECTION 10.8 FB DATA OUT 8 SELECTION 10.9 AUX CW DATA IN SELECTION Parameter defnes the nput process data coupled to Aux Control Word. 0 = Not used 1 = PDI1 2 = PDI2 3 = PDI3 4 = PDI4 5 = PDI5 9 Tel (0) Fax +358 (0)

113 parameter descrptons vacon Prohbted Frequences (Control panel: Menu PAR -> P11) 11.1 PROHIBIT FREQUENCY RANGE 1: LOW LIMIT 11.2 PROHIBIT FREQUENCY RANGE 1: HIGH LIMIT 11.3 PROHIBIT FREQUENCY RANGE 2: LOW LIMIT 11.4 PROHIBIT FREQUENCY RANGE 2: HIGH LIMIT Two skp frequency regons are avalable f there s a need to avod certan frequences because of e.g. mechancal resonance. In ths case the actual frequency reference sent to the motor control wll be kept out of these ranges accordng to the example below, where one range s n use. Actual Reference Hgh Lm Low Lm Low Lm Hgh Lm Requested Reference Fgure 9.15: Frequency Range 24-hour support +358 (0) Emal: vacon@vacon.com 9

114 110 vacon parameter descrptons 9.12 Protectons (Control panel:menu Par->P13) 13.5 STALL PROTECTION 0 = No acton 1 = Alarm 2 = Fault, stop functon 3 = Fault, coast The motor stall protecton protects the motor from short tme overload stuatons such as one caused by a stalled shaft. The stall current s I nmotor *1.3, stall tme 15 seconds and stall frequency lmt 25 Hz. If the current s hgher than the lmt and output frequency s lower than the lmt, the stall state s true and the drve reacts accordng to ths parameter. There s actually no real ndcaton of the shaft rotaton. I Stall area Inmotor *1.3 25Hz f Fgure 9.16: Stall characterstcs 13.6 UNDER LOAD PROTECTION 0 = No acton 1 = Alarm 2 = Fault, stop functon 3 = Fault, coast The purpose of the motor underload protecton s to ensure that there s load on the motor when the drve s runnng. If the motor loses ts load there mght be a problem n the process, e.g. a broken belt or a dry pump. The underload protecton tme lmt s 20 seconds, whch s the maxmum tme allowed for an underload state to exst before causng a trp accordng to ths parameter. 9 Tel (0) Fax +358 (0)

115 parameter descrptons vacon 111 Torque Underload curve at nomnal freq. = 50% Underload curve at zero freq. = 10% 5 Hz Underload area Feld weakenng pont, P1.11 Fgure 9.17: Underload protecton f 13.7 MOTOR THERMAL PROTECTION 0 = No acton 1 = Alarm 2 = Fault, stop functon 3 = Fault, coast If trppng s selected the drve wll stop and actvate the fault stage, f the temperature of the motor becomes too hgh. Deactvatng the protecton,.e. settng parameter to 0, wll reset the thermal model of the motor to 0%. The motor thermal protecton s to protect the motor from overheatng. The drve s capable of supplyng hgher than nomnal current to the motor. If the load requres ths hgh current there s a rsk that the motor wll be thermally overloaded. Ths s the case especally at low frequences. At low frequences the coolng effect of the motor s reduced as well as ts capacty. If the motor s equpped wth an external fan the load reducton at low speeds s small. The motor thermal protecton s based on a calculated model and t uses the output current of the drve to determne the load on the motor. The motor thermal protecton can be adjusted wth parameters. The thermal current I T specfes the load current above whch the motor s overloaded. Ths current lmt s a functon of the output frequency. CAUTION! The calculated model does not protect the motor f the arflow to the motor s reduced by blocked ar ntake grll. 24-hour support +358 (0) Emal: vacon@vacon.com 9

116 112 vacon parameter descrptons 13.8 MTP:AMBIENT TEMPERATURE When the motor ambent temperature must be taken nto consderaton, t s recommended to set a value for ths parameter. The value can be set between -20 and 100 degrees Celsus MTP:ZERO SPEED COOLING The coolng power can be set between % x coolng power at nomnal frequency. See Fgure P coolng 100% Overload area I T par =40% 0 f n f Fgure 9.18: Motor coolng power MTP:THERMAL TIME CONSTANT Ths tme can be set between 1 and 200 mnutes. Ths s the thermal tme constant of the motor. The bgger the motor, the longer the tme constants. The tme constant s the tme wthn whch the calculated thermal model has reached 63% of ts fnal value. The motor thermal tme s specfc to the motor desgn and t vares between dfferent motor manufacturers. If the motor's t6-tme (t6 s the tme n seconds the motor can safely operate at sx tmes the rated current) s known (gven by the motor manufacturer) the tme constant parameter can be set basng on t. As a rule of thumb, the motor thermal tme constant n mnutes equals to 2 x t6. If the drve s n stop state the tme constant s nternally ncreased to three tmes the set parameter value. See also Fgure Tel (0) Fax +358 (0)

117 parameter descrptons vacon 113 Motor temperature 105% Trp area Motor current I/IT Fault/warnng actvaton pont, f selected wth par Tme cons tantt *) Motor temperature Q=(I/IT) 2 x(1-e -t/t ) Tme *) Changes by motor sze and adjusted wth parameter Fgure 9.19: Motor temperature calculaton 24-hour support +358 (0) Emal: vacon@vacon.com 9

118 114 vacon parameter descrptons 9.13 Automatc reset (Control panel: Menu PAR -> P14) 14.1 AUTOMATIC RESET Actvate the Automatc reset after fault wth ths parameter. NOTE: Automatc reset s allowed for certan faults only. Fault: 1. Under voltage 2. Over voltage 3. Over current 4. Motor temperature 5. Under load 14.3 TRIAL TIME The Automatc restart functon restarts the frequency converter when the faults have dsappeared and the watng tme has elapsed. The tme count starts from the frst autoreset. If the number of faults occurrng durng the tral tme exceeds three, the fault state becomes actve. Otherwse the fault s cleared after the tral tme has elapsed and the next fault starts the tral tme count agan. See Fgure If a sngle fault remans durng the tral tme, a fault state s true. Fault trgger Wat tme pa r Wat tme par.14.2 Wat tme par Motor stop sgnal Restart 1 Restart 2 Motor start sgnal Supervs on Fault actve RESET/ Fault reset Tral tme par.14.3 Autoreset functon: (Trals = 2) Fgure 9.20: Example of Automatc restarts wth two restarts 9 Tel (0) Fax +358 (0)

119 parameter descrptons vacon PID control parameters (Control panel: Menu PAR -> P15) 15.7 P GAIN Ths parameter defnes the gan of the PID controller. If the value of the parameter s set to 100%, a change of 10% n the error value causes the controller output to change by 10% PID CONTROLLER I-TIME Ths parameter defnes the ntegraton tme of the PID controller. If ths parameter s set to 1,00 second, the controller output s changed by a value correspondng to the output caused from the gan every second. (Gan*Error)/s PID CONTROLLER D-TIME Ths parameter defnes the dervatve tme of the PID controller. If ths parameter s set to 1,00 second, a change of 10% n the error value causes the controller output to change by 10% FEEDBACK VALUE MINIMUM 15.6 FEEDBACK VALUE MAXIMUM Ths parameter sets the mnmum and maxmum scalng ponts for feedback value. Controller feedback (%) par par V 0 ma Custom mn par. 6.2 /6.6 Custommax par. 6.3 /6.7 10V 20mA Analogue nput wth custom mn and max scalng (%) Fgure 9.21: Feedback mnmum and maxmum 24-hour support +358 (0) Emal: vacon@vacon.com 9

120 116 vacon parameter descrptons SLEEP MIN FREQUENCY SLEEP DELAY WAKE-UP ERROR Ths functon wll put the drve nto sleep mode f the frequency stays below the sleep lmt for a longer tme than that set wth the Sleep Delay (P15.12). Ths means that the start command remans on, but the run request s turned off. When the actual value goes below, or above, the wake-up error dependng on the set actng mode the drve wll actvate the run request agan f the start command s stll on. Actual value Wake up error P15.13 Frequency Sleep delay P15.12 Sleep mn frequency P15.11 Regulatng mode Sleep Regulatng mode Fgure 9.22: Sleep mn frequency, Sleep delay,wake-up error - Some parameters lke P15.16 seem to lack descrpton n the manual, I thnk t would be good to revew the parameter descrptons aganst the parameter lst. - System menu seem to lack descrpton, e.g. the password procedure requred some practcng to fnd out how t s to be used - In page 53 wth wrng examples the DI source s maybe not needed as the DI source wrng s already shown n the general wrng schematc on the prevous page 9 Tel (0) Fax +358 (0)