PRO-CRIMPER* III Hand Crimping Tool Assembly and Die Assemblies [ ]
|
|
- Whitney Heath
- 5 years ago
- Views:
Transcription
1 PRO-CRIMPER* III Hand Crmpng Tool Assembly and De Assembles [ ] Instructon Sheet MAR 14 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually powered hand tools. Hand tools are ntended for occasonal use and low volume applcatons. A wde selecton of powered applcaton equpment for extended-use, producton operatons s avalable. PRO-CRIMPER III Hand Crmpng Tool Shown Front of Tool De Assembly Movng Jaw Statonary Jaw Pvot Pn Back of Tool (Wre Sde) PRO-CRIMPER III Hand Crmpng Tool Frame (Instructon Sheet ) ORIGINAL INSTRUCTIONS Ratchet Adjustment Wheel The PRO-CRIMPER III Hand Crmpng Tool s a Commercal grade tool and s desgned prmarly for feld nstallaton, repar, mantenance work, or prototypng n ndustral, commercal, or nsttutonal applcatons. Product crmped wth ths tool wll meet the crmp heght requrement for hand tools n the approprate Applcaton Specfcaton (114-seres), but may not comply wth other feature parameters of the specfcaton. TE Connectvty offers a varety of tools to satsfy your performance requrements. For addtonal nformaton, contact the Toolng Assstance Center at Movng Handle Statonary Handle DIE ASSEMBLY PRODUCT FAMILY (SOLISTRAND*) SIZE (AWG) WIRE STRIP LENGTH (mm [n.]) Termnal (Standard) [ ] Termnal (Standard) and Butt Splce [ ] Termnal (Long Barrel) or Butt Splce [ ] Termnal Parallel Splce [ ] Contact the Toolng Assstance Center or Product Informaton (at the number lsted below) for specfc termnal and splce part numbers. See page 6 for de assembly cross reference. Fgure 1 1. INTRODUCTION De Assembly [ ] and PRO-CRIMPER III Hand Tool are used to crmp SOLISTRAND Termnals and Splces onto the wre sze lsted n Fgure 1. PRO-CRIMPER III Hand Tool Assembly conssts of Hand Tool Frame and De Assembly Read these nstructons thoroughly before usng the tool assembly. Specfc part numbers for de set [ ] may be used wth other optonal crmp toolng. Refer to Fgure 7 for specfc relatonshps. Dmensons n ths nstructon sheet are n metrc unts [wth U.S. customary unts n brackets]. Fgures and llustratons are for reference only and are not drawn to scale TE Connectvty famly of companes All Rghts Reserved *Trademark TOOLING ASSISTANCE CENTER PRODUCT INFORMATION Ths controlled document s subject to change. For latest revson and Regonal Customer Servce, vst our webste at TE Connectvty, TE connectvty (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of ther respectve owners. 1 of 6 LOC B
2 Statonary Jaw Indenters Upper De De Retanng Screws Lower De Anvls Fgure 2 Ths document supersedes Instructon Sheet Reasons for ressue of ths nstructon sheet are provded n Secton 8, REVISION SUMMARY. 2. DESCRIPTION (See Fgures 1 and 2) The tool consst of a statonary jaw and handle, a movng jaw and handle, and an adjustable ratchet that ensures full crmpng. The tool frame holds a de assembly wth three crmpng chambers. The de assembly features an upper de and a lower de. De retanng screws are used to poston and secure the des n the tool frame. 3. DIE ASSEMBLY INSTALLATION AND REMOVAL 1. Open the tool handles and remove the two de retanng screws from the tool jaws. 2. Place the upper de n the statonary jaw of the tool frame so that the largest ndenter s facng nward. See Fgure Insert the de retanng screw through the statonary jaw and through the de. Tghten the screw just enough to hold the de n place. Do not tghten the screw completely at ths tme. 4. Place the lower de n the movng jaw of the tool frame so that the largest anvl s facng nward. See Fgure Insert the de retanng screw through the movng jaw and through the de. Tghten the screw just enough to hold the de n place. Do not tghten the screw completely at ths tme. 6. Carefully close the tool handles, makng sure that the anvls and ndenters algn properly. Contnue closng the tool handles untl the ratchet has engaged suffcently to hold the des n place, then tghten both de retanng screws. 7. To dsassemble, open the tool handles untl the ratchet releases, remove the two de retanng screws, and slde the des out of the tool jaws. 4. CRIMPING PROCEDURE Before usng the tool, the crmpng chambers and tool ratchet should be nspected as specfed n Secton 5, CRIMP HEIGHT INSPECTION, and Secton 6, RATCHET (Shut Heght) ADJUSTMENT. Refer to Fgure 1 and select wre of the specfed sze and nsulaton dameter. Strp the wre to the length ndcated, takng care not to nck or cut wre strands. Select an applcable termnal or splce and dentfy the approprate crmpng chamber accordng to the wre sze markngs on the des. Refer to Fgure 3 and proceed as follows: The crmpng chamber marked cannot be used to crmp spade-type termnals. 1. Hold tool so that the back (wre sde) s facng you. Squeeze tool handles together untl the ratchet releases, then allow them to open fully. 2. Center the termnal or splce wre barrel on the anvl of the upper de as shown n Fgure 3. If vsble, be sure to place the brazed seam on the termnal or splce toward the ndenter. 2 of 6
3 Termnal Termnal Wre Barrel Centered on Anvl of Lower De Splce Strpped Wre hold the termnal or splce n poston. Do NOT deform the nsulaton barrel or wre barrel. 4. Insert strpped wre nto the wre barrel, makng sure that the nsulaton does not enter the wre barrel. See Fgure To crmp the other half of a splce, reposton the uncrmped wre barrel n the crmpng chamber, and repeat the crmpng procedure. 6. To crmp the other half of a splce, reposton the uncrmped wre barrel n the crmpng chamber, and repeat the crmpng procedure. If splce cannot be turned for crmpng the other half, turn the tool around. 7. Inspect the crmped termnal or splce accordng to Fgure 4. Check the crmp heght as descrbed n Secton 5. If necessary, adjust the ratchet (shut heght) as descrbed n Secton 6. Termnal Splce Wre Barrel Centered on Anvl of Lower De Parallel Splce Butt Splce Brazed Seam Postoned Toward Indenter Inspecton Hole Parallel Splce Splce Wre Barrel Centered on Anvl of Lower De Fgure 3 3. Hold the wre barrel n place and squeeze the tool handles together untl ratchet engages suffcently to Fgure 4 3 of 6
4 CAUTION! Damaged termnals and splces may not be used. If a damaged termnal or splce s evdent, t must be replaced wth a new one. 5. CRIMP HEIGHT INSPECTION Ths nspecton requres the use of plug gages conformng to the dmensons provded n Fgure 5. TE does not manufacture or market these gages. To gage the crmpng chamber, proceed as follows: 1. Remove traces of ol or drt from the crmpng chamber and plug gage. 2. Close the tool handles untl the des have bottomed. Do NOT force des beyond ntal contact. for [ ] 3. Algn the GO element wth the crmpng chamber. Push element straght nto the crmpng chamber wthout usng force. The GO element must pass completely through the crmpng chamber. See Fgure Algn the NO-GO element and try to nsert t straght nto the same crmpng chamber. The NO-GO element may start entry, but must not pass completely through the crmpng chamber. See Fgure 5. If the crmpng chamber conforms to the gage nspecton, the tool s consdered dmensonally correct, and should be lubrcated wth a THIN coat of any good SAE 20 motor ol. If not, the tool must be returned to TE for further evaluaton and repar. Refer to Secton 8, REPLACEMENT. For addtonal nformaton regardng the use of a plug gage, refer to Instructon Sheet CRIMPING CHAMBER (De Markng) GAGE ELEMENT DIMENSIONS GO NO-GO R (RADIUS) [ ] [ ] [ ] [ ] [ ] [ ] 1.57 [.062] 1.98 [.078] 2.77 [.109] 6. RATCHET (SHUT HEIGHT) ADJUSTMENT (Fgure 6) The frame assembly ratchet mechansm features an adjustment wheel wth numbered settngs. If the des do not bottom, adjust the ratchet as follows: 1. Remove the lockscrew from the ratchet adjustment wheel. 2. Wth a screwdrver, adjust the ratchet wheel from the opposte sde of the frame. 3. Observe the ratchet adjustment wheel. If the des do not bottom, rotate the adjustment wheel COUNTERCLOCKWISE to a hgher-numbered settng. 4. Replace the lockscrew. Screwdrver GO Element Must Pass Completely Through Crmpng Chamber NO-GO Element May Start Entry, But Must Not Pass Completely Through Crmpng Chamber Fgure 5 Ratchet Adjustment Wheel Lockscrew Fgure 6 4 of 6
5 7. MAINTENANCE AND INSPECTION 7.1. Mantenance Ensure that the tool and des are clean by wpng them wth a clean, soft cloth. Remove any debrs wth a clean, soft brush. Do not use objects that could damage the tool. When not n use, keep handles closed to prevent objects from becomng lodged n the crmpng des, and store n a clean, dry area Vsual Inspecton The de assembly should be nspected on a regular bass to ensure that they have not become worn or damaged. Inspect the crmpng chambers for flattened, chpped, worn, or broken areas. If damage or abnormal wear s evdent, the tool or des must be replaced. See Secton 8, REPLACEMENT. 8. REPLACEMENT Customer-replaceable parts are shown n Fgure 1. Avalable separately, PRO-CRIMPER III Hand Crmpng Tool Repar Kt ncludes a replacement nut and a varety of pns, rngs, screws, and sprngs. If the des are damaged or worn excessvely, they must be replaced. Order the repar kt and replaceable parts through your TE Representatve, or call , or send a facsmle of your purchase order to , or wrte to: CUSTOMER SERVICE ( ) TYCO ELECTRONICS CORPORATION PO BOX 3608 HARRISBURG PA For tool repar servce, please contact a TE Representatve at REVISION SUMMARY Updated document to corporate requrements Added clarfyng note to table n Fgure 1 5 of 6
6 Toolng Compatble wth De Assembly [ ] De Assembly for PRO-CRIMPER III Hand Tool Frame (Instructon Sheet ) De Assembly for SDE-SA Hand Tool (Instructon Sheet ) De Assembly for SDE Bench Termnator (Customer Manual ) De Assembly for 626 Adapter (Instructon Sheet ) De Assembly for Electro-Hydraulc (BT 3500 Battery-Hydraulc) Hand Tool Kts [ ] (Customer Manual ) Closed Head Assembly (Instructon Sheet ) C -Head Assembly (Instructon Sheet ) Fgure 7 6 of 6
PRO- CRIMPER* III Hand Crimping
PRO- CRIMPER* III Hand Crmpng Instructon Sheet Tool 58448-2 408-9357 Wth De 58448-3 10 Mar 11 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually powered hand
More informationPRO-CRIMPER* III Hand Tool Assembly with Die Assembly
PRO-CRIMPER* III Hand Tool Assembly 2063778-1 wth De Assembly 2063778-2 Instructon Sheet 408-10290 02 FEB 12 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually
More informationPRO- CRIMPER* III Hand
PRO- CRIMPER* III Hand Instructon Sheet Crmpng Tool Assembly 58529-1 408-9999 wth De Assembly 58529-2 11 AUG 14 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually
More informationPRO- CRIMPER* III Hand
PRO- CRIMPER* III Hand Instructon Sheet Crmpng Tool Assembly 90759-1 408-9962 wth De Assembly 90759-2 03 MAY 11 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually
More informationPRO-CRIMPER* III Hand Crimping Tool Assembly with Die AssemblY
PRO-CRIMPER* III Hand Crmpng Tool Assembly 90758-1 wth De AssemblY 90758-2 Instructon Sheet 408-9938 01 NOV 11 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually
More informationPRO- CRIMPER* III Hand Crimping
PRO- CRIMPER* III Hand Crmpng Instructon Sheet Tool Assembly 58641-1 wth 408-4379 De Assembly 58641-2 18 JUN 09 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually
More informationPRO- CRIMPER* III Hand Crimping
PRO- CRIMPER* III Hand Crmpng Instructon Sheet Tool Assembly 91338-1 408-8377 wth De Assembly 91338-2 22 JUL 09 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually
More informationPRO- CRIMPER III Hand Crimping Tool Assembly INSTALLATION AND REMOVAL OF DIE SET AND LOCATOR ASSEMBLY (Figure 2)
PRO- CRIMPER* III Hand Crmpng Instructon Sheet Tool Assembly 90547-1 wth 408-9884 De Assembly 90547-2 02 NOV 09 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually
More informationPRO- CRIMPER III Hand Crimping Tool Assembly DESCRIPTION (Figures 1 and 2)
PRO- CRIMPER* III Hand Crmpng Instructon Sheet Tool Assembly 58495-1 408-9819 Wth De Assembly 58495-2 22 JUL 09 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually
More informationPRO-CRIMPER* III Hand. with Die Assembly OCT 11 Rev C. Pivot Pin. Die Assembly Moving Jaw CONTACT FAMILY SIZE (AWG)
PRO-CRIMPER* III Hand Instructon Sheet Crmpng Tool Assembly 58514-1 408-9973 wth De Assembly 58514-2 12 OCT 11 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually
More informationPRO-CRIMPER* III Hand Crimping Tool Assembly with Die Assembly
PRO-CRIMPER* III Hand Crmpng Tool Assembly 90548-1 wth De Assembly 90548-2 Instructon Sheet 408-9885 02 NOV 12 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually
More informationonlinecomponents.com
PRO- CRIMPER* III Hand Crmpng Instructon Sheet Tool Assembly 58535-1 wth 408-4021 De Assembly 58535-2 29 JUL 09 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually
More informationPRO- CRIMPER* III Hand
PRO- CRIMPER* III Hand Instructon Sheet Crmpng Tool Assembly 90684-1 408-9934 wth De Assembly 90684-2 09 OCT 09 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually
More informationInstruction Sheet SDE- SA Hand Tool Assembly with Die Assembly
Instructon Sheet 408-10002 wth De Assembly 1752938-2 06 APR 10 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually powered hand tools. Hand tools are ntended for
More informationSDE PEW- 12 Hand Tool
SDE PEW- 12 Hand Tool Instructon Sheet Assembly 2063956-1 wth 408-10370 De Assembly 2063956-2 07 OCT 10 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually powered
More informationHand Crimping Tool (For Insulated Heat Shrink Splices)
Hand Crmpng Tool 607949-1 (For Insulated Heat Shrnk Splces) Instructon Sheet 408-4087 23 JAN 12 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually powered hand
More informationSTRATO-THERM* Terminal and Splice Hand Crimping Tools and 59461
STRATO-THERM* Termnal and Splce Hand Crmpng Tools 59294 and 59461 Instructon Sheet 408-1259 17 AUG 10 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually powered
More informationLocator Pin Indexing Pin. Wire Size Marking CAUTION NOTE TOOLING ASSISTANCE CENTER PRODUCT INFORMATION
ROTA-CRIMP* Crmpng Tool Instructon Sheet 408-2681 68321-1 13 APR 12 Statonary De (Nest) Anvl De Hold-Down Devce and Contact Locator Front of Tool Locator Pn Indexng Pn Wre Sze Markng The hold-down devce
More informationInsertion/Extraction Tool and Replacement Tip Kits [ ]
Inserton/Extracton Tool 91285-1 and Replacement Tp Kts 543382-[ ] Instructon Sheet 408-9404 19 JUN 12 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually powered
More informationInstruction Sheet ROTA- CRIMP* Hand Crimping Tools and
Instructon Sheet ROTA- CRIMP* Hand Crmpng Tools 08-09 6007 and 6007- APR PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually powered hand tools. Hand tools are
More informationTerminating Tools
Termnatng Tools 2-231652- 5 Instructon Sheet and 2-231652- 9 for 408-9770 DEConnect Modular Plugs 29 NOV 10 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually
More informationPRO- CRIMPER* III Hand Crimping
PRO- CRIMPER* III Hand Crimping Instruction Sheet Tool Assembly 58448-2 408-9357 With Die Assembly 58448-3 10 Mar 11 PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use
More informationAUG 15 Rev M
ORIGINAL INSTRUCTIONS PRO-CRIMPER III Hand Crimping Tool Assembly 58433-3 with Die Assembly 58423-1 Instruction Sheet 408-9252 21 AUG 15 Rev M PROPER USE GUIDELINES Cumulative Trauma Disorders can result
More informationInstruction Sheet AMPMODU* MTE CONNECTORS Mar 11 Rev A
Instructon Sheet AMPMODU* MTE CONNECTORS 408-6919 10 Mar 11 PROPER USE GUIDELINES Cumulatve Trauma Dsorders can result from the prolonged use of manually powered hand tools. Hand tools are ntended for
More informationPneumatic Power Bench Assembly
Pneumatc Power Bench Assembly 58338-1 Instructon Sheet 408-9393 09 AUG 11 Fgure 1 1. INTRODUCTION Pneumatc Power Bench Assembly 58338-1 s a pneumatc power unt desgned to accept a varety of nterchangeable
More informationShur-Plug*.156 Diameter Terminals and Receptacle Contacts
Shur-Plug*.156 Dameter Termnals and Receptacle Contacts Applcaton Specfcaton 114-2042 07 NOV 12 All numercal values are n metrc unts [wth U.S. customary unts n brackets]. Dmensons are n mllmeters [and
More informationSDE Electric Bench Terminator READ THIS FIRST! customer manual TOOLING ASSISTANCE CENTER
SDE Electrc Bench Termnator 1490076-2 Customer Manual 409-10052 31 JAN 12 customer manual SAFETY A. PRECAUTIONS READ THIS FIRST!............................ 2 1. INTRODUCTION........................................................
More informationMCP 2.8 mm Contact System and Wire Seal for 1P Starter Motor Connectors
MCP 2.8 mm Contact System and Wre Seal for 1P Starter Motor Connectors Applcaton Specfcaton 114-13295 05 MAY 11 All numercal values are n metrc unts [wth U.S. customary unts n brackets]. Dmensons are n
More informationA socket contact support (supplied separately) must be installed onto the locator assembly.
Figure 1 PRO CRIMPER III Hand Tool Assembly 1976444 1 consists of PRO CRIMPER III Hand Tool Frame 354940 1 and Die Assembly 1976444 2. The tool assembly is used to crimp the contacts listed in Figure 1.
More informationonlinecomponents.com
Figure 1 PRO CRIMPER III Hand Crimping Tool Assembly 58603 1 consists of Die Assembly 58603 2 and PRO CRIMPER III Hand Tool Frame 354940 1. The die assembly consists of crimping dies and a locator assembly.
More informationRead these instructions thoroughly before crimping any contacts.
PRO CRIMPER III Hand Crimping Tool Assembly 58583 1 consists of Die Assembly 58583 2 and PRO CRIMPER III Hand Crimping Tool Frame 354940 1. The die assembly consists of crimping dies and a locator assembly.
More informationJUL 15 Rev E
ORIGINAL INSTRUCTIONS SDE PEW-12 Hand Crimping Tool Assembly 2031734-1 with Die Assembly 2031734-2 Instruction Sheet 408-10243 02 JUL 15 Rev E PROPER USE GUIDELINES Cumulative Trauma Disorders can result
More informationTerminals and Splices 19 OCT 11 Rev D. Crimping Dies for Head Numbers 69065, 69067, and Hand Tool Yoke. Place Screwdriver Here to Remove Dies
Instruction Sheet Crimping Dies for SOLISTRAND* 408-9786 Terminals and Splices 19 OCT 11 PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools.
More informationAMPINNERGY* Modular Wiring System 25 JUL 11 Rev G
Applcaton Specfcaton 114-6039 AMPINNERGY* Modular Wrng System 25 JUL 11 Rev G All numercal values are n metrc unts [wth U.S. customary unts n brackets]. Dmensons are n mllmeters [and nches]. Unless otherwse
More informationHand Crimping Tools , , and AUG 12 Rev D
Instruction Sheet 408-7332 Hand Tools 90123-2, 90123-5, and 90124-2 29 AUG 12 PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools
More informationSOLISTRAND* Flag Terminal Crimping Dies
SOLISTRAND* Flag Terminal Crimping Dies Instruction Sheet 408-8908 22 DEC 10 PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools
More informationConnector Assemblies 06 JUN 11 Rev C
Applcaton Specfcaton Power Seres 50 114-13071 Connector Assembles 06 JUN 11 All numercal values are n metrc unts [wth U.S. customary unts n brackets]. Dmensons are n mllmeters [and nches]. Unless otherwse
More informationTerminal and Splice , , and JUN 12 Rev D NOTE. CERTI-CRIMP* Hand Crimping Tool Ratchet Control CAUTION NOTE
Terminal and Splice Instruction Sheet Crimping Tools 408-1254 69339, 69354-1, and 69355 11 JUN 12 PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered
More informationCrimping Dies for SOLISTRAND* Terminals and Splices
ORIGINAL INSTRUCTIONS Crimping Dies for SOLISTRAND* Terminals and Splices Instruction Sheet 408-8691 02 AUG 18 Rev H1 PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use
More informationDESCRIPTION 3. DIE INSTALLATION AND REMOVAL Die Removal (Figure 3) 3.1. Die Installation (Figure 3) Hydraulic Hand Tool
Crimping Dies Instruction Sheet for SOLISTRAND* 08 869 s and Splices 9 APR PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools
More informationHydraulic Hand Crimping Tool, PN
ORIGINAL INSTRUCTIONS Hydraulic Hand Crimping Tool, PN 59975-1 Instruction Sheet 408-6758 21 JUN 17 Rev F PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually
More informationCrimping Dies for TERMINYL* and PLASTI-GRIP* Terminals and Splices
Crimping Dies for TERMINYL* and PLASTI-GRIP* Terminals and Splices Instruction Sheet 408-10051 11 APR 17 Rev D PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually
More informationHand Crimping Tool [ ]
408-8738 Revision T, Jan. 2017 PRO-CRIMPER III Hand Crimping Tool 790163-[ ] 1. Introduction PRO-CRIMPER III Hand Crimping Tool Assembly 790163-[ ] consists of PRO-CRIMPER III Hand Tool Frame 354940-1
More informationOCT 14 Rev K
ORIGINAL INSTRUCTIONS Hand Crimping Tool 68026 for TERMI-FOIL* Product Instruction Sheet 408-2363 27 OCT 14 Rev K PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of
More informationType III+ (Size 16) Contacts 15 MAR 11 Rev L
Applcaton Specfcaton 114-10004 Type III+ (Sze 16) Contacts 15 MAR 11 Rev L NOTE All numercal values are n metrc unts [wth U.S. customary unts n brackets]. Dmensons are n mllmeters [and nches]. Unless otherwse
More informationSOLISTRAND* Crimping Dies
SOLISTRAND* Crimping Dies Instruction Sheet (Used in Crimping Heads 08-697 69097 and 69099) 5 APR Terminals Butt Splices Parallel Splices = Wire Barrel DIE SET NUMBERS FOR DIE SET CRIMPING HEAD 69097 NUMBERS
More informationCrimping Dies; PN thru 47825, 47915, and 47918
Crimping Dies; PN 47820 thru 47825, 47915, and 47918 Instruction Sheet 408-1729 22 NOV 16 Rev K Crimping Dies; PN 47820 thru 47825, 47915, and 47918 (Typical) Crimping Die Wire Size Part Number Color Code
More informationUltra- Fast Series 110, 125,
Ultra- Fast Seres 0, 25, Applcaton Specfcaton 87, 205, and 250 Fully- Insulated 4-223 FASTON* Termnals 22 FEB 3 Rev H All numercal values are n metrc unts [wth U.S. customary unts n brackets]. Dmensons
More informationCrimping Die Assemblies , , , , , , , , and 69653
Crimping Die Assemblies 46754-2, 46755-2, 46756-2, 46757-2, 46758-2, 46759-2, 46760-2, 59870-1, and 69653 Instruction Sheet 408-1602 10 NOV 16 Rev C 1. INTRODUCTION WIRE SIZE (MCM) (1) CMA (Circular Mil
More informationFEB 18 Rev D
ORIGINAL INSTRUCTIONS Terminal and Splice Crimping Die Assemblies Instruction Sheet 408-1632 01 FEB 18 Rev D PROPER USE GUIDELINES Cumulative trauma disorders can result from the prolonged use of manually
More informationThis instruction sheet covers the application and maintenance procedures for Crimping Die Assembly
Figure 1 This instruction sheet covers the application and maintenance procedures for Crimping Die Assembly 318106 1. For additional information on COPALUM terminals and splices, refer to Catalog 82020.
More informationinstructions packaged with the tools or contact the Tooling Assistance Center number at the bottom of this page.
This instruction sheet provides instructions on product application, and maintenance and inspection procedures for SOLISTRAND Crimping Dies which are used in Crimping Heads 69097 and 69099. See Figure
More informationAPR 15 Rev A
ORIGINAL INSTRUCTIONS CERTI-CRIMP* Hand Tools 47386-4, 47387-7, and 525690-1 Instruction Sheet 411-1050 24 APR 15 Rev A PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use
More informationRefer to Figure 2 and select the appropriate wire, die assembly, and terminal or splice. Strip the wire to the length indicated in the table.
The die assemblies consist of stationary dies (nests) and moving dies (anvils). Refer to Figure 2 to ensure the compatibility of die assemblies, crimping heads, and terminals and splices. The shanks on
More informationOCT 15 Rev E
ORIGINAL INSTRUCTIONS Coaxial Cable Stripper Kits 603995-[ ] Instruction Sheet 408-2766 09 OCT 15 Rev E PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered
More information1. Actuate the upper die release button located in the C head or closed head. 2. Slide the nest into place in C head or closed head. See Figure 2.
The die assemblies consist of stationary dies (nests) and moving dies (anvils). The dies are retained in the crimp tool by retainer pins. Refer to the table in Figure 3 to ensure the compatibility of die
More informationC O N C E A L E D F I X I N G. PH:
C O N C E A L E D I X I N G D I Y S l a t Systems PH: 1300 336 237 Alumnum Concealed xng Slat Systems Our Concealed xng Alumnum Slat range offers the latest n archtectural style combned wth a unque nstall
More informationHigh Current Pin and Socket Contacts 31 JUL 13 Rev C
Application Specification High Current Pin and Socket Contacts 31 JUL 13 NOTE NOTE i All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and
More informationInstruction Sheet 2 mm Common Termination (CT) Head Assembly
Instruction Sheet 2 mm Common Termination (CT) 408-9426 Head Assembly 58372-1 05 MAY 14 Wire Inserter (Shown In Up Position) Carriage Drag Wire Guide Feed Pawl (Portion of Head Assembly Shown Cut Away
More informationMICROWAVE HOOD COMBINATION INSTALLATIONINSTRUCTIONS
MICROWVE HOOD COMINTION INSTLLTIONINSTRUCTIONS Ths product s sutable for use above electrc or gas cookng products up to 36" (91.4 cm) wde. These nstallaton nstructons cover dfferent models. The appearance
More information2E - 3E High Wind Kit Manual
Yag Dpole Vertcal (Patent# 6,677,914 E - 3E Hgh Wnd Kt Manual Antarctca at 7 mph SteppIR Antennas 11-116th Ave NE, Sute -, Bellevue, WA 984 Tel: 4-43-191 Fax: 4-46-441 Tech Support: 4-891-6134 www.steppr.com
More information2. Remove assembly pins from mounting lugs as. shown in Figure 1.
This instruction sheet provides instructions on product application and Maintenance and Inspection for Insulation Piercing COPALUM Terminal and Splice Crimping Heads (68081 and 68082) used in Pneumatic
More informationcurrent activity shows on the top right corner in green. The steps appear in yellow
Browzwear Tutorals Tutoral ntroducton Ths tutoral leads you through the basc garment creaton process usng an llustrated step by step approach. Each slde shows the actual applcaton at the stage of the acton
More informationFEATHER LODGE BASE CABINET ASSEMBLY GUIDE
FETHER LODGE SE CINET SSEMLY GUIDE WELCOME TO FETHER LODGE CINETS Thank you for purchasng Feather Lodge cabnets. You are on your way to a beautful, new ktchen, vanty, or closet. There are a few smple tools
More informationDynamic Optimization. Assignment 1. Sasanka Nagavalli January 29, 2013 Robotics Institute Carnegie Mellon University
Dynamc Optmzaton Assgnment 1 Sasanka Nagavall snagaval@andrew.cmu.edu 16-745 January 29, 213 Robotcs Insttute Carnege Mellon Unversty Table of Contents 1. Problem and Approach... 1 2. Optmzaton wthout
More informationChecking Terminal Crimp Height or Gaging the Die Closure
Checking Terminal Crimp Height or Gaging the Die Closure Instruction Sheet 408-7424 27 MAR 18 Rev S 1. INTRODUCTION Crimp height comparators and plug gages are instruments recommended for verifying the
More informationTITLE ASSEMBLY DRAWING MTA - 5" APPROVALS DRAWN DATE
REV. DESCRPTON APPROVED A SEE DCN: 7762 0/29/200 ha k9, EXPRESS PROR WRTTEN CONSENT OF CELESCO TRANSDUCER PRODUCTS N( 20630 Plummer st Chatsworth, CA. 93 G MTA 5" E.GARCA 029200 SZE CODE DENT. NO DWG.
More informationMULTIPOLE CONNECTORS SQUICH CN NEW SQUICH. Connections without tools reduced space SQUICH A TIMESAVER
SCREW CONNECTION ULTIPOLE CONNECTORS SQUICH CN SQUICH SQUICH Connectons wthout tools reduced space A TIESAVER SQUICH ULTIPOLE CONNECTORS SQUICH CN SQUICH seres Connectons wthout tools To mprove hgh performance
More informationDEUTSCH Instructional Manual for HDP-400 Power Crimper (TE CONNECTIVITY PN )
ORIGINAL INSTRUCTIONS DEUTSCH Instructional Manual for HDP-400 Power Crimper (TE CONNECTIVITY PN 1606312-1) Instruction Sheet 0425-034-0000 15 JAN 18 Rev H NOTE All numerical values are in metric units
More informationMICROWAVEHOODCOMBINATION INSTALLATIONINSTRUCTIONS
MCROWVEHOODCOMNTON NSTLLTONNSTRUCTONS Ths product s sutable for use above electrc or gas cookng products up to and ncludng 36" (91.4 cm) wde. See "nstallaton Requrements" secton for further notes. These
More informationINSTRUCTION MANUAL BENCH LATHE
WLLOUGHBY COMMUNTY MEN'S SHED mens 296C Salors Bay Road, l _ L^ NORTHBRDGE N.S.W 2063 The Wlkmghby Communty" NSTRUCTON MANUAL BENCH LATHE Before usng be sure to read ths manual carefully -C6- Safety nstructons
More informationph fax
www.customron.com ph 800.732.7699 fax 507.732.7837 Balusters, pckets, spndles these are the bones of a star ralng system. At Custom Iron, we commonly refer to these as balusters. And, uncommonly, we nvent
More informationApplication Tooling Specification Sheet
Hand Crimp Tool FEATURES Application Tooling Specification Sheet Order No. 200218-2300 % A full cycle ratcheting hand tool ensures complete crimps % Ergonomically designed soft handles % Precisely designed
More informationApplication Tooling Specification Sheet
HAND CRIMP TOOL Application Tooling Specification Sheet TYPE 4D Order No. 63828-0200 FEATURES A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping
More informationNordic - 2 Door Wardrobe
Nordc - 2 oor Wardrobe ssembly Instructons - lease keep for future reference 62967 mensons Wdth : 8. cm epth : 49,0 cm Heght : 9, cm Important - lease read these nstructons fully before startng assembly
More informationOrder Number
Order Number 200218-5500 FEATURES Application Tooling Specification TYPE 4D A full-cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping A precision user-friendly
More informationVS- 3 Hand Tool Kits , , and
VS- 3 Hand Tool Kits 244271-1, 244271-5, and 244271-6 Instruction Sheet 408-7280 Jan 2017 PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools.
More informationStrain Gauge Measuring Amplifier BA 660
Stran Gauge Measurng Amplfer BA 660 Orgnal of the Manual BA660 / IP20 BA660 / IP66 Table of Contents 1. Safety precautons...2 1.1. Feld of applcaton...2 1.2. Installaton...2 1.3. Mantenance...2 2. Functon...2
More informationProduct Information. Jaw quick-change system BSWS-PGZN-plus
Product Informaton BSWS-PGZN-plus BSWS-PGZN-plus Productve. Flexble. Cost-effectve. BSWS jaw quck-change system The BSWS jaw quck-change system allows top jaws to be changed on the grpper manually and
More informationHow to Get Started with Virtual Goalie
How to Get Started wth Vrtual Goale HTC VIVE Set up your computer and moble devce Acqure a vrtual realty-enabled computer and the HTC Vve. For hardware specs, to test your computer, or to order from Amazon,
More informationHV Modular Die Holder (With Fine Adjust), PN
HV Modular Die Holder (With Fine Adjust), PN 2305470-1 Instruction Sheet 408-35048 24 DEC 18 Rev B INTRODUCTION Figure 1 The HV Modular Die Holder with Fine Adjust (PN 2305470-1) is a product line that
More informationApplication Tooling Specification Sheet
HAND CRIMP TOOL FEATURES Application Tooling Specification Sheet TYPE 4D Order No. 63827-1400 A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping
More informationInstruction Sheet Tool Kit [ ] (for SL Series 110 Jack Connectors)
Instruction Sheet Tool Kit 1725150 [ ] (for SL Series 110 Jack Connectors) 26 FEB 04 PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools.
More informationApplication Tooling Specification
Order No. 63828-1200 Application Tooling Specification Type 4D FEATURES A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping A precision, user-friendly
More informationInstructions for Use. PetChatz.com. PetChatz.com
Instructons for Use PetChatz.com PetChatz.com POWER ON/OFF LED PET-SAFE MICROPHONE SOUND DETECTOR MANUAL TREAT RELEASE LOW TREAT LED LOW-LIGHT HD CAMERA for hgh-qualty vdeo MOTION DETECTION FULL-COLOR
More informationCluster Block Housings and Contacts
Cluster Block Housings and Contacts Application Specification 114-2019 20 SEP 17 Rev J NOTE i All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters
More informationParking barrier Parc 200 / Parc 200 speed
GB Operatng nstructons Last updated: 01.2014 Parkng barrer Parc 200 / Parc 200 speed 1. Meanng of symbols 2. Table of contents Advce Cauton! Danger of personal njury! The followng safety advce must be
More informationSCOPE Perma-Seal Terminals and Splices AWG (Rings, Spades, Hooks, 3 and 4-Ways, and Splices). RHT-5770 Hand Crimp Tool
Hand Crimp Tool Operating Instruction Sheet and Specifications Part No. 64001-3200 Eng. No. RHT 5770 (Replaces 19285-0050 and 19285-0143) FEATURES A full cycle ratcheting hand tool ensures complete crimps
More informationOrder Number
Order Number 200218-5900 FEATURES Application Tooling Specification TYPE 4D A full-cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping A precision user-friendly
More informationCOMMERCIAL PORTABLE CRIMP TOOLING
COMMERCIAL PORTABLE CRIMP TOOLING A FLEXIBLE APPROACH TO PORTABLE CRIMPING INTRODUCTION TO TOOLING SOLUTIONS TE Connectivity. A Leader in Crimp Quality. Anyone can make a tool to crimp terminals onto a
More informationApplication Tooling Specification
Order No. 63819-0901 Application Tooling Specification Type 4D FEATURES A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping A precision, user-friendly
More informationApplication Tooling Specification Sheet
HAND CRIMP TOOL Application Tooling Specification Sheet TYPE 4D Order No. 63819-0000 FEATURES A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping
More informationSTAR POWER BOM/BOQ SETTING IDEA 1 - TWIST & SHOUT
Below are two deas for settng your blocks together. Of course, there are dozens more! Take your blocks out to play, and decde on a settng that makes you smle! STAR POWER BOM/BOQ SETTING IDEA 1 - TWIST
More informationNordic - 2 Door 2 Drawer Tallboy
Nordc - oor rawer allboy ssembly Instructons - lease keep for future reference 66390 mensons Wdth : 8. cm epth : 49,0 cm Heght : 5,9 cm Important - lease read these nstructons fully before startng assembly
More informationScrew Hole. Figure 1 TOOLING ASSISTANCE CENTER PRODUCT INFORMATION
Application Specification Solderless Light Emitting Diode (LED) 114-32038 Socket (Type LK) 07 SEP 12 NOTE i All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions
More informationApplication Tooling Specification Sheet
HAND CRIMP TOOL Application Tooling Specification Sheet TYPE 4D Order No. 63819-0400 FEATURES A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping
More informationApplication Tooling Specification
Order No. 200218-2200 Application Tooling Specification Type 4D FEATURES A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping A precision, user-friendly
More informationVRT014 User s guide V0.8. Address: Saltoniškių g. 10c, Vilnius LT-08105, Phone: (370-5) , Fax: (370-5) ,
VRT014 User s gude V0.8 Thank you for purchasng our product. We hope ths user-frendly devce wll be helpful n realsng your deas and brngng comfort to your lfe. Please take few mnutes to read ths manual
More informationHand Crimp Tool Operating Instruction and Specifications Sheet Part No Eng. No. RHT 5770 (Replaces and )
Hand Crimp Tool Operating Instruction and Specifications Sheet Part No. 64001-3200 Eng. No. RHT 5770 (Replaces 19285-0050 and 19285-0143) FEATURES Œ A full cycle ratcheting hand tool ensures complete crimps
More informationApplication Tooling Specification Sheet
Tool Kit Order No. 63811-5370 FEATURES Application Tooling Specification Sheet TYPE 4C Hand Crimp Tool Order No. 63811-5300 % A full cycle ratcheting hand tool ensures complete crimps % Ergonomically designed
More information