Basic Layout Techniques

Transcription

1 Basic Layout Techniques Rahul Shukla Advisor: Jaime Ramirez-Angulo Spring 2005 Mixed Signal VLSI Lab Klipsch School of Electrical and Computer Engineering New Mexico State University

2 Outline Transistor layout Resistor Layout Capacitor Layout Common Centroid and Inter-digitization Techniques Example layouts Pad Frame

3 Transistor layout NMOS D B G S 1.5um/0.6um NMOS Bulk terminal in AMI 0.5µm process is always tied to p substrate which is tied to Vss. S/D G D/S PMOS S B G D 1.5um/0.6um PMOS Bulk terminal in AMI 0.5µm process is free (N Well process) and can be connected to any voltage but usually connected to Vdd or the source S terminal. B S/D G D/S

4 Transistor layout A single large transistor layout is not a good idea!!! To make a large transistor we split the large transistors and connect them in parallel. G G G G G D S D S D S B S B B B B 120um/1.8um 30um/1.8um 30um/1.8um 30um/1.8um 30um/1.8um Generally PMOS width (W) < 50µm/1.8µm NMOS width (W) < 30µm/1.8µm

5 Transistor layout G G D B 120um/1.8um S S/D D/S

6 Transistor layout S B D G 150µm/1.05µm G D S PMOS Bulk terminal connected to the source S terminal reduce body effect. Four transistor of 37.5µm/1.05µm connected in parallel B

7 Resistor layout Resistor value is calculated using R=Rs (L/W) where Rs is sheet resistance of ELEC layer and its value in AMI 0.5µm process is 1024Ω/ ٱ L and W are length and width of resistor. Resistor is implemented using a POLY2 layer or ELEC as it is called in Cadence. A High-Res layer is also used as a layer ID. Use minimum W of ELEC to calculate length of ELEC layer Value of W and L calculated using formula is an approximate value. To get a value close enough to desired value, layout the resistor, extract the layout using the extractor tool in Cadence and and see the value in extracted view of your cell and change the size of the resistor in layout view to get to a desired value. This, as we can see is an iterative process.

8 Example 5kΩ resistor layout. Resistor layout L W ELEC Extracted view of the resistor M1_ELEC Contact Highres

9 Resistor layout For laying out a big resistor it is recommended to split it into series connection of small resistors. E.g.: 25kΩ using five 5kΩ resistor layout. (note the 25kΩ is not a large value resistor)

10 Use minimum W=L so that a square capacitor implementation is possible. Value of W and L calculated using formula is an approximate value. To get a value close enough to desired value, layout the capacitor, extract the layout using the extractor tool in Cadence and see the value in extracted view of your cell and accordingly change the size of the capacitor in layout to get to a desired value. This, as we can see is an iterative process. Capacitor layout Capacitor value is calculated using R=C ox W.L where C ox is capacitance of oxide layer per unit area. Its value in AMI 0.5µm process is 2.4fF/µm 2, L and W are length and width of capacitor. A parallel plate Capacitor is implemented using a POLY2 layer or ELEC as it is called in Cadence and POLY layer. The two layer act act as the parallel plate. A cap-id layer can also be used as a layer ID.

11 Example 1pF capacitor layout. Capacitor layout M1_ELEC contact ELEC POLY Cross section M1_POLY contact Oxide layer

12 Common Centroid and Interdigitization Techniques Process variations during fabrication may limit accuracy and desired performance of analog circuits. Matching between components in layout of analog circuits is an important issue in many designs. For e.g. current mirrors, differential pairs. Inter-digitization and common centroid are the most basic techniques to match components in layouts. [1] [1] CMOS Circuit design, layout and simulation, R. Jacob Baker, Harry W. Li and David E. Boyce, chapter 20 and 24, IEEE press. 1998

13 Common Centroid and Interdigitization Techniques A simple example of how process variation affects circuit performance Iin Iout Assuming that we split M2 in 4 equal sized transistor and do the layout in following fashion. If process was ideal (W/L) M2 = 4(W/L) M1 G G G G G W/L M1 M2 4W/L D B S S D S D S W/L M1 W/L M21 W/L M22 W/L M23 W/L M24 Ideally I out = 4I in (neglecting 2 order effects) Since the process is non-ideal we assume a linear variation along horizontal axis for example a 1% increase in W/L ratio of each transistor as we go along left to right. G G G G G Practically I out = 4.1I in (neglecting 2 order effects) D S D S D S B S W/L M1 1.01W/L M W/L M W/L M W/L M24

14 Common Centroid and Interdigitization Techniques Process variations do not only affect W/L ratio (aspect ratio) but also other variation like V t i.e. threshold voltage etc. Mismatch in a simple differential amplifier will lead to undesirable effects like offset, poor CMRR etc. Vin+ Vbias M3 Vdd M5 M4 Vin- Matching important between M1 M2 Vout Differential pair Mirror Differential Amplifier

15 Common Centroid and Interdigitization Techniques We have to match two components A and B ( A and B can be anything like capacitor, resistor or transistor). Lets split A and B into 4 small components i.e. A1-A4 and B1-B4. Inter-digitization Technique: Placing alternate components A1 B1 A2 B2 A3 B3 A4 B4 Common centroid Technique: Placing components such that both components have same centroid. Both A and B have common center. A1 B1 B2 A2 A3 B3 B4 A4

16 Example of common centroid technique (Matching between M3 and M4 of differential amplifier). (W/L) M3 = (W/L) M4 M3 M4 M4 M3 M3 M4 M4 M3

17 Another example of common centroid technique (W/L) M1 = 2(W/L) M2 M1 M2 M1 M1 M2 M1 An alternative approach of M1 M1 M2 M2 M1 M1 can also be used!!!

18 Another example of common centroid technique for matching in capacitor array at the input stage of a DAC. C 2C 4C 8C 16C Poly serves as the common bottom plate Dummy capacitors Done by Milind Sawant for input stage of a DAC

19 Example layouts Use NTAP contact around transistors and try to use M2 for horizontal connections and M3 for vertical connections or vice versa.

20 Example layouts

21 Pad Frame 40 PINS P pins are protected pins + is VDD pin - is VSS pin Pins with no names are bare pins. It has a global guard rings. Guard rings Pin # 1 Pin # 40