Installation Instructions For Aurora Halogen Accent Housing 3 Round & Square Trimless AH3-ARE3-RGB & AH3-ASE3-RGB. Fig.
|
|
- Percival Griffin
- 6 years ago
- Views:
Transcription
1 0 Pure Lighting. All Rights Reserved. Installation Instructions For Aurora Halogen Accent Housing Round & Square Trimless AH-ARE-RGB & AH-ASE-RGB W. Fullerton Ave Chicago, IL 606 Tel: Fax: General Information Fixture must be installed by a qualified electrician (check with local and national codes for proper installation). To prevent electrical shock, disconnect electrical supply before installation or servicing. Compatible only with traditional, level 5 surface finishing, not self-leveling, PVA primer systems. Not for use in wood or tile ceilings. Fig. Complete Fixture 6 /6" (5mm) HOUSING DRYWALL ANCHOR SCREENS WORKFLOW CHART ELECTRICAL CTRACTOR. Locate and mount housing. Screw and lock-in housing. Connect wires un housing 5 /" (9mm) /" (0mm) /" (5mm) /" (0mm) PLASTER PLATE DRYWALL CTRACTOR. Install and cut drywall around housing. ELECTRICAL CTRACTOR. Adjust plaster flange frame and tighten wing nuts.. Connect the MR6 and LEDS wiring to the plaster plate.. Screw plaster plate into housing.. Test MR6 and LEDs. DRYWALL CTRACTOR. Plaster, sand & paint.. Clean aperture with clean damp towel. Adjustable Gears Hidden Behind the Lamp Tilt Gear Hot Aiming with Phillips Screw driver Fig. Pan tilt Mechanism attached to inside of plaster plate. Light Spill Shield Pan Lock Pan Rotation Ring LED Spring Clip RGB LED's ELECTRICAL CTRACTOR. Clean aperture with clean damp towel, where the drywall contractor missed.. Adjust pan rotation ring and aim lamp. You're done! Important Scan with your mobile device to watch the installation video or visit a-install Importante Escanear con el dispositivo móvil para ver el video de instalación o visite a-install HOT AIMING TILT SCREW Fig. Snoot Assembly LIGHT SPILL SHIELD 5 BULLET CATCHES SNOOT RETAINING RING LOCKING RING (INCLUDED) MR6 HALOGEN LAMP LY LOCKING RING (INCLUDED) SOFT FOCUS LENS (INCLUDED) LENS (OPTIAL) LOUVER (OPTIAL) SNOOT LAMP HOLDER
2 A DRYWALL ANCHOR SCREENS 5 /" (9mm) /" (5mm) /" (6mm) ALIGNMENT NOTCH C REMODEL NOTE: CUT DRYWALL TO MIDDLE OF JOIST. NOTE: APERTURE IS CENTERED WITH CURVES IN HOUSING. ALIGNMENT NOTCH /" (0mm) : Use these dimensions when locating the center point of the aperture during the installation process. Align the fixture using a laser or a chalk line. NOTE: Drywall anchor screens may be removed, if the joist are less than /" apart. : After fixture is positioned, tighten all (0) screws on hanger bars. B D NOTE: APERTURE IS CENTERED WITH CURVES IN HOUSING. (NOT CENTER IN FIXTURE) MUST BE FLUSH WITH JOIST : Hanger bars must align and remain flush with joist. : After installation, pull on fixture to ensure there is no movement.
3 CNECT LINE VOLTAGE INSIDE THE FIXTURE. 5A
4 CNECT DATA WIRES INSIDE THE FIXTURE, AND TO SET FIXTURE ADDRESS REFER TO PDSA OPERATIAL GUIDE PAGES 9&0 FOR MORE INFORMATI. 5B TO SET FIXTURE ADDRESS REFER TO PDSA OPERATIAL GUIDE PAGES 9&0. Aurora RGB PDS-A
5 DRYWALL CTRACTOR E G CUTOUT DRYWALL 9 PLASTER FLANGE FRAME ROTARY TOOL LOOSEN WINGNUTS TO ADJUST PLASTER FLANGE FRAME : Drywall contractor must install drywall and cut /" (5mm) X /" (0mm) hole with rotary cutting tool around fixture or pre-cut hole in drywall prior to installation. Contratista hojas de pared tiene que instalar la hoja de pared y corte un aqujero /" (5mm) X /" (0mm) con une corte rotatorio alrededor el enseres fijo o lo corte un agujero antes que instalar. 9: Loosen () wing nuts and adjust plaster flange frame to be flush with drywall. All corners MUST be exactly even with drywall. Plaster flange frame adjusts to accommodate /" (mm) to /" (mm) ceiling thickness. F ELECTRICAL CTRACTOR DRYWALL ANCHOR SCREEN H CEILING DRYWALL ANCHOR SCREW : Electrian must anchor drywall anchor screens. Insert screws through drywall into anchor screen on fixture. 0 0: Use a straight edge or level and move plaster flange frame up or down to be exactly even with drywall ceiling. 5
6 I TIGHTEN WINGNUTS TO ADJUST PLASTER FLANGE FRAME K : Tighten () wing nuts securely. : Loosely attach plaster plate using all () screws. After all () screws are started, go back and tighten the screws securely. J L LED QUICK CNECTOR USE A PEN TO TIGHTEN LOCKING RINGS. LAMP LOCKING RING LOUVER AND LENS LOCKING RING SNOOT LAMP HOLDER : Electrian must anchor drywall anchor screens. Insert screws through drywall into anchor screen on fixture. : Check to ensure that the plaster plate is flush and even with the drywall. 6
7 M O 5 RED, GREEN AND BLUE LED UPLIGHT, MAKE SURE ALL THREE LED'S ARE WORKING. MR6 HALOGEN ACCENT LIGHT (NO MR6 LED) RED, GREEN AND BLUE LED UPLIGHT, MAKE SURE ALL THREE LED'S ARE WORKING. HANDS MUST BE CLEAN WHEN ADJUSTING FIXTURE 5: Turn on and test MR6 and LEDs to ensure they are properly installed. : Tilt and rotate MR6 as needed. When lamp is properly adjusted secure pan lock. N P OPEN SPACE RACK GEAR COVER TOP CLIP HANDS MUST BE CLEAN WHEN ADJUSTING FIXTURE BOTTOM CLIP : Measure the distance of the open space on the track. 6: To aim lamp, loosen pan lock, rotate and position the pan rotation ring. 9: Remove the protective film from the gear cover. 0: Cut the gear cover to fit the space if necessary.
8 Q APERTURE S 5 RACK GEAR COVER GEAR COVER RACK PAINT OVER PAINT SHIELD. REMOVE PAINT SHIELD 0-60 MINUTE AFTER PAINTING. PINTAR SOBRE EL PROTECTOR DE PINTURA REMOVER EL PINTURA 0-60 MINUTOS DESPUES DE PINTAR. : Insert the gear cover (make sure the gear cover clips are facing the lamp assembly rack) from the bottom of the aperture. 5: Paint (Pintar). : Secure by snapping in the two bottom clips of the gear cover first to the bottom edge, then snap in the top two clips to the top edge. R DRYWALL CTRACTOR Compatible only with traditional, level 5 surface finishing, not self-leveling, PVA primer systems. APPLY A THIN LAYER OF DURABD 5 COMPOUND AROUND ALL FOUR SIDE. DO NOT USE TAPE. DO NOT USE PVA PRIMER SYSTEMS. APLICAR UNA CAPA DELGADA DE DURABD 5 ALREDEDOR DE LOS CUA MAKE SURE THE SHIELD IS IN PLACE. (ASEGURASE QUE EL PROTECTOR DE PINTURA ESTES PUESTO.) T REMOVE ANY EXCESS PAINT THAT IS THE BEVELED EDGE. ANY EXCESS PAINT WILL BE NOTICEABLE WHEN LIGHT IS POWERED. WIPE INSIDE OF APERTURE WITH CLEAN DAMP TOWEL. (REMOVER CUALQUIER EXCESO DE PINTURA. CUALQUIER EXCESO DE PINTURA SERA NOTABLE CUANDO LA LUZ ESTA ENCENDIDO. LIMPIE ADENTRO DE LA APERTURA C UNA TOALLA LIMPIA Y HUMEDA). SAND AND PLASTER AGAIN, UNTIL SMOOTH FINISH IS ACHIEVED. LIYAR Y YWSO OTRA VES HASTA QUE SUPERFICIE ESTES COMPLETAMENTE LISO. CLEAN INSIDE OF FIXTURE WITH COMPRESSED AIR TO REMOVE ANY REMAINING CSTRUCTI DEBRIS. (LIMPIA ADENTRO DE ENSERES FIJO C AIRE COMPRIMIDO PARA REMOVER CUALQUIER POLVO QUE HALLA QUEDADO ADENTRO). 6 : Plaster (Yeso). 6: Clean Area. : Sand (Liyar).
9 U HANDS MUST BE CLEAN WHEN ADJUSTING FIXTURE : Wash hands and clean all drywall residue from inside aperture, with a clean damp towel. Electrician or lighting designer - ensure pan rotation ring is adjusted, locked in place, and the lamp is aimed properly. 9
10 OPERATI GUIDE FOR PDSA RGB Control Color changing LEDs combine red, green and blue light at different intensities to create dynamic color effects. The color of an AURORA RGB can be either permanently assigned to the fixture during installation or adjusted remotely with the use of an external controller. Any external controller can be used so long as it uses the standardized lighting communication protocol known as DMX. Operating in a DMX environment gives the user the greatest flexibility when it comes to customizing or creating dramatic effects. Depending on the functionality of the controller, you will be able to control each individual color and each fixture independently. Selecting Modes The AURORA RGB operates in Stand Alone Mode or DMX Mode. The mode can be selected with DIP switch #0 (See Figure A). On=DMX Mode Off=Stand Alone Mode. Any adjustments to the DIP switch settings should be made with electricity removed from device. Stand Alone Mode In this mode, DIP switches -9 are used to select a fixed color for applications where only one color is needed and no controller is present. Enter this mode by placing DIP switch #0 OFF. Multiple DIP switches can be adjusted to blend custom colors. Any adjustments to the DIP switch settings should be made with electricity removed from device. In Stand Alone Mode the device will not respond any DMX signals. Stand Alone Mode DIP POSITI EFFECT OFF OFF OFF RED 00% RED 50% GREEN 00% GREEN 50% BLUE 00% BLUE 50% TEST SEQUENCE TEST SEQUENCE TEST SEQUENCE MODE Example: Shown with red light glowing at 00% intensity. Figure A Aurora RGB PDS-A DMX Mode In this mode, DIP switches -9 are used to select the DMX starting address. Any address -50 is possible. Enter this mode by placing DIP switch #0. Any adjustments to the DIP switch settings should be made with electricity removed from device. In the event that no DMX signal is present for any period of time greater than second, the AURORA RGB will revert to Signal Loss Mode. In this mode all LEDs will glow at 50% intensity until the DMX signal is resorted. 0
11 DMX Addressing DMX mode enables the use of an external DMX controller. Each fixture requires a "start address" from to 50. A fixture requiring one or more channels for control begins to read the data on the channel indicated by the start address. For example, a fixture that occupies or uses channels of DMX and was addressed to start on DMX channel 00, would read data from channels: 00, 00, and 00, Choose start addresses so that the channels used do not overlap and notate the start address selected for future reference. Each Aurora RGB fixture uses three channels of control. Channel Value Percent 0-00% 0-00% 0-00% Function Red Intensity 0-00% Green Intensity 0-00% Red Intensity 0-00% DMX Dipswitch Quick Reference Chart Example: 5 DMX STARTING ADDRESS # DMX STARTING ADDRESS # DMX STARTING ADDRESS #
Installation Instructions For Aurora Halogen Accent Housing 3 Round & Square Trimless AH2-ARE3 & AH2-ASE3. Fig.1 Complete Fixture
015 Pure Lighting. All Rights Reserved. Installation Instructions For Aurora Halogen Accent Housing 3 Round & Square Trimless AH-ARE3 & AH-ASE3 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1195
More informationAURORA HALOGEN ACCENT HOUSING 3 ROUND AND SQUARE TRIMLESS AH3-ARE3-RBG & AH3-ASE3-RGB INSTALLATION INSTRUCTIONS
AURORA HALOGEN ACCENT HOUSING 3 ROUND AND SQUARE TRIMLESS AH3-ARE3-RBG & AH3-ASE3-RGB INSTALLATION INSTRUCTIONS Fixtures must be installed by a qualified electrician (check with local and national codes
More informationInstallation Instructions For Aurora Halogen Accent Housing 3 Round & Square Trimless AH2-ARE3 & AH2-ASE3. Fig.1 Complete Fixture
015 Pure Lighting. All Rights Reserved. Installation Instructions For Aurora Halogen Accent Housing 3 Round & Square Trimless AH-ARE3 & AH-ASE3 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1195
More informationInstallation Instructions For Aurora Halogen Accent Housing 3 Round & Square Trimless AH1-ARE, AH1-ARB, AH1-ASE, AH1-ASB. Fig.
2015 Pure Lighting. All Rights Reserved. Installation Instructions For Aurora Halogen Accent Housing 3 Round & Square Trimless AH1-ARE, AH1-ARB, AH1-ASE, AH1-ASB 1718 W. Fullerton Ave Chicago, IL 60614
More informationInstallation Instructions For Aurora Dual MR16 Round & Square Edge 3.3" Fig.1 Complete Fixture ADJUSTABLE GEARS HIDDEN BEHIND THE LAMP PAN LOCK
2015 Pure Lighting. All Rights Reserved. Installation Instructions For Aurora Dual MR16 Round & Square Edge 3.3" 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1195 Fax: 773-935-5613 www.purelighting.com
More informationInstall the Housing. Installation Instructions for Entra Round or Square Type IC, Air-tight New Construction Adjustable LED Housing EN3_-LH9_ 1.
Installation Instructions for Entra Round or Square Type IC, Air-tight New Construction Adjustable LED Housing 90ENTRA EN_-LH9_. LED - ROUND/ SQUARE GENERAL PRODUCT I NFORMATION: This product is safety
More informationInstallation Instructions For TruLine 1.6A 24VDC
2014 Pure Lighting. All Rights Reserved. Installation Instructions For TruLine 1.6A 24VDC INS# 902-TL1.6A-07 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1195 Fax: 773-935-5613 www.purelighting.com
More informationRound or Square Type IC Wall Wash Housing with Lamp for Flangeless Trims
Installation Instructions for 90ELED-WIC Round or Square Type IC Wall Wash Housing with Lamp for Flangeless Trims LED E_L_-L_WI. LED - ROUND/ SQUARE FLANGELESS GENERAL PRODUCT I NFORMATION: This product
More information2. Connect driver to power source leads. After connections are made, place driver above ceiling. SEE MINIMUM SPACE REQUIREMENTS BELOW.
INSTALLATION INSTRUCTIONS INSTALLATION: 1. Cut proper opening in ceiling. Round: 140mm Ø, Square: 140mm x 140mm 140mm Ø 140mm x 140mm 2. Connect driver to power source leads. After connections are made,
More informationINSTALLATION INSTRUCTIONS FOR FLUSH MOUNT FIXTURES
Kurt Versen Company Point Source Lighting 10 Charles Street Westwood, New Jersey Models with Square or Rectangular Apertures 1 PLEASE READ THIS ENTIRE INSTRUCTION SHEET BEFORE INSTALLATION. 2 DISCONNECT
More informationRound or Square Chicago Plenum Down Light Housing with Lamp
Installation Instructions for 90ELED-DCP Round or Square Chicago Plenum Down Light Housing with Lamp LED E_-L_DC. LED - ROUND/ SQUARE GENERAL PRODUCT I NFORMATION: This product is suitable for indoor locations.
More informationMultiples EM_ 1.4. Install 1X1/1X2/1X3/1X4 Housings. Installation Instructions for. This product is suitable for indoor locations.
Installation Instructions for 90EMULTI Multiples EM_. GENERAL PRODUCT I NFORMATION: This product is suitable for indoor locations. This product can be dimmed with a standard electronic dimmer or a 0-0V
More informationInstallation Instructions For Reveal
2017 Pure Lighting. All Rights Reserved. Installation Instructions For Reveal IS# 902-RV-24VDC-07 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1196 Fax: 773-883-6128 www.purelighting.com info@purelighting.com
More informationINSTALLATION INSTRUCTIONS FOR FLUSH MOUNT FIXTURES
Kurt Versen Company Point Source Lighting Models with Round Apertures 10 Charles Street Westwood, New Jersey 1 PLEASE READ THIS ENTIRE INSTRUCTION SHEET BEFORE INSTALLATION. 2 DISCONNECT ELECTRICAL POWER
More informationInstallation Instructions for TruLine 1.6A 24VDC. Section One: Basic Configuration Options
Doc # 902-TL1.6A_07 1718 W. Fullerton Chicago, IL 60614 Ph: 773.770.1195 Fax: 773.935.5613 www.pureedgelighting.com info@pureedgelighting.com 2016 PureEdge Lighting. All Rights Reserved. Installation Instructions
More informationRound or Square Type IC Down Light Housing with LED Lamp for Flangeless Trims E3_L_-L_DI 1.4
Installation Instructions for 90ELED-DIC Round or Square Type IC Down Light Housing with LED Lamp for Flangeless Trims E_L_-L_DI. LED - ROUND/ SQUARE FLANGELESS GENERAL PRODUCT I NFORMATION: This product
More informationINSTALLATION INSTRUCTION Silo Multiples - New Construction Housing MT-4*15, MT-4*10
IMPORTANT SAFETY INSTRUCTIONS 1. Read all instructions before installing. 2. System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations.
More informationLightplane 3.5 Recessed
INSTALLATION INSTRUCTIONS Lightplane 3.5 Recessed LP3.5R Recessed Ceiling IMPORTANT SAFETY INSTRUCTIONS When installing or using this fixtures basic safety precautions must be followed. Read all instructions
More informationwith Lamp Install the Housing with Adjustable Bars Installation Instructions for LED E3_-L_DN 1.1 ½ to ¾ ¾ or thicker
Installation Instructions for 90ELED-D Round or Square Type IC, Non-IC Down Light Housing with Lamp LED E_-L_DN. LED - ROUND/ SQUARE GENERAL PRODUCT I NFORMATION: This product is suitable for indoor locations.
More informationInde-Pendants Family. 32L Ring Plaster Trim, Grid and Drywall Ceiling Types. Document No Installation instructions for 32L-Rxx-P
Inde-Pendants Family 32L Ring Plaster Trim, Grid and Drywall Ceiling Types Installation instructions for 32L-Rxx-P Document No. Supplied by Litecontrol 32L Inde-Pendants: Ring (Plaster Trim, Grid and Drywall
More informationInde-Pendants Family. 32L Surface Mount Cylinder with Ring Plaster Trim, Grid and Drywall Ceiling Types. Document No
Inde-Pendants Family 32L Surface Mount Cylinder with Ring Plaster Trim, Grid and Drywall Ceiling Types Installation instructions for 32L-CRxx-S-D Document No. Supplied by Litecontrol 32L Inde-Pendants:
More informationInstallation Instructions For Reveal Light Channel
2016 Pure ighting. All Rights Reserved. Installation Instructions For Reveal ight Channel IS# 902-RV-24VDC-06 1718 W. Fullerton Ave Chicago, I 60614 Tel: 773-770-1195 Fax: 773-935-5613 www.purelighting.com
More informationInstalling Fixture Using Remote Power Supply
2017 Edge Lighting. All Rights Reserved. 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1195 Fax: 773-935-5613 www.edgelighting.com info@edgelighting.com 904-BV2-2K4K-_03 BV2-1RE-_-2K4K-_ Installation
More informationInde-Pendants Family. 32L Surface Mount Cylinder Plaster Trim, Grid and Drywall Ceiling Types. Document No
Inde-Pendants Family 32L Surface Mount Cylinder Plaster Trim, Grid and Drywall Ceiling Types Installation instructions for 32L-C-S-D Document No. Supplied by Litecontrol 32L Inde-Pendants: Cylinder (Surface
More information5 ACCESS PANEL INSTALLATION SPACER *SLIDE TO LOCATION OF FASTENER DURING INSTALLATION OF EACH FASTENER
1/2 K.O. (3/8 K.O. on 165 with factory supplied 3/8 flex conduit fitting) TR - Trim Flange Side Blocking Install Method Secure fixture to structure following instructions below: 1. Remove lens and internal
More information3% VOLTAGE DROP. Installation Instructions for 400 Watt 24 Volt DC RGB DMX LED Power Supply SAVE THESE INSTRUCTIONS!
Installation Instructions for 400 Watt 24 Volt DC RGB DMX LED Power Supply Doc # 904-PSB-400W-24VDC_06 1718 W. Fullerton Chicago, IL 60614 Ph: 773.770.1195 Fax: 773.935.5613 www.pureedgelighting.com info@pureedgelighting.com
More informationINDIVIDUAL MOUNTING: T-Bar
X1 (T-BAR) INSTALLATION INSTRUCTIONS GENERAL NOTES NOTE : Additional support to structural member may be required. Check with local building codes for requirement. 1. Place troffer clamp approx. 6 from
More informationDOWNLIGHT LED SERIES INSTALLATION INSTRUCTIONS
WARNING: This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Make sure all
More informationInstallation Instructions Standalone or continuous run configurations - 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS
- 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS TruGroove Drywall A3 MOUNTING Ceiling INSTALLATION System Overview These instructions review how to install trimless drywall versions of TruGroove
More informationLED RECESSED ADJUSTABLE 3-1/4 APERTURE Non-IC Rated, 1000 LUMEN TC49L, TC949L
PRODUCT DESCRIPTION Recessed adjustable 0W LED luminaire produces up to 000 fixture lumens (depending on trim) and approximates the performance of a 75W MR6 lamp. Fixture has 50 visual cutoff and features
More informationInstallation Instructions for DIY or Completed 45 Degree Light Channel
201 Edge Lighting. All Rights Reserved. Installation Instructions for DIY or Completed Degree Light Channel IMPORTANT INFORMATION - This instruction shows a typical installation. 11 W. Fullerton Ave Chicago,
More informationPMT-L31 (for Low Ceilings) PMT-H35 (for High Ceilings)
English Ceiling Mount Bracket PMT-L31 (for Low Ceilings) PMT-H35 (for High Ceilings) Installation Manual Be sure to read this manual thoroughly before using this bracket. After you have read this manual,
More informationBLACK BODY DIMMING & TUNABLE WHITE 1000 LUMEN ADJUSTABLE, DOWNLIGHT AND WALL WASH LED ROUND APERTURE IC410T, TC410T P1.16.0
PRODUCT DESCRIPTION Recessed LED luminaire compatible with adjustable, downlight and wall wash trims, features both Black Body Dimming and Tunable White technology in a single fixture and delivers up to
More informationLine volt rail & fixtures. Low volt quick connect fixtures with transformers
INSTRUCTIONS: Line Volt Flexrail2 Safety Instructions: A qualified electrician must install system only. System is intended for installation in accordance with National Electric Code, local and Federal
More informationPORTA~TRACE. GAGNE, INC. 41 Commercial Dr. Johnson City, New York Phone: Fax: ASSEMBLY INSTRUCTIONS
PORTA~TRACE GAGNE, INC. 41 Commercial Dr. Johnson City, New York 13790 Phone: 1-607-729-3366 Fax: 1-607-729-7644 ASSEMBLY INSTRUCTIONS PORTA~TRACE MODEL 2436T LIGHT TABLE PORTA~TRACE MODEL 3648T LIGHT
More informationRAIL 4 INSTALLATION INSTRUCTIONS. RM4DOD Recessed GENERAL SAFETY INSTRUCTIONS: NOTE:
INSTALLATION INSTRUCTIONS RAIL 4 RM4DOD Recessed NOTE: The following instructions provide general guidelines for product installation. For additional information consult the applicable electrical codes
More informationInstallation Instructions for Zip Suspension Downlight with Remote Power and 4" Square or Round Canopy
Doc # 90-ZS-SQ_0 W. Fullerton Chicago, IL 0 Ph:.0.9 Fax:.9. www.pureedgelighting.com info@pureedgelighting.com 0 PureEdge Lighting. All Rights Reserved. Installation Instructions for Zip Suspension Downlight
More information- 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS. Factory pre-installed mud flange TOOLS REQUIRED: Phillips screwdriver, 5/16 nut driver.
- 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS TruGroove Drywall A3 MOUNTING Ceiling INSTALLATION System Overview These instructions review how to install drywall trim versions of TruGroove recessed
More informationEXPLODED VIEW AND PART CALL OUT ASSEMBLING THE METALUX DF SERIES FRAME KIT
EXPLODED VIEW AND PART CALL OUT CUTOUT DIMENSIONS ON PAGE 2 CEILING BRACING (BY OTHERS) SHEET ROCK METALUX DF SERIES FRAME KIT S282 (2'X2') FIXTURE SHOWN FIXTURE SIZE FRAME KIT PART # 2' X 2' DF-22W-U
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationJoiner Kit Joiner bracket (x1) Biscuit aligners (x2) Trim Flange
- Trim System Overview These instructions review how to install TruGroove Perimeter fixtures. Modules can be installed as individual standalone units, or they can be joined together to create continuous
More informationREGOLO GENERAL WARNING
REGOLO GENERAL WARNING WARNING: DO NOT ASSEMBLE CONTINUOUS RUN ON THE GROUND AND LIFT INTO PLACE. JOINTS WILL DISTORT AND NOT CREATE A TIGHT FIT. JOINING HARDWARE WILL HAVE TO BE PURCHASED AND REPLACED.
More informationInstallation Instruction
Tools Needed for Assembly Stud finder (for wood stud wall) Pencil Mark Electric drill Wood Stud Wall Installation Step 1. Locate the Wood Studs Installation Instruction Drill bit (for wood stud wall) Masonry
More informationInstallation Instructions for DIY or Completed Light Channel.6 Millwork
2017 Edge Lighting. All Rights Reserved. 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 77-770-1195 Fax: 77-95-561 www.edgelighting.com info@edgelighting.com LCMW.6- - - 904-LCMW.6_02 Installation Instructions
More informationCloset Carousel Installation Instructions. Models TKA 5 Through TKA 14 Equipped with Footswitch Controls
Tools Required: Phillips Screwdriver (#2) Adjustable Wrench Level Tape Measure Utility Knife Electric Drill Drill Bits for Anchors Ladder (4 foot) Models TKA 5 Through TKA 14 Equipped with Footswitch Controls
More informationSURFACE CLIP MOUNT. 1 Insert lens into channel, measure, and cut to length. Remove lens cover from channel. surface. Attach lens cover and end caps
SURFACE CLIP MOUNT 1 Insert lens into channel, measure, and cut to length Remove lens cover from channel Screw mounting clips into mounting Snap channel into mounting clips Attach lens cover and end caps
More informationInstallation Instructions for Cirrus Suspension Downlight with Power - End Feed. Section One: 4" Flush Canopy Version
Doc # 0-CSP-E_0 W. Fullerton Chicago, IL 606 Ph:.0. Fax:..6 www.pureedgelighting.com info@pureedgelighting.com 06 PureEdge Lighting. All Rights Reserved. Installation Instructions for Cirrus Suspension
More informationØ1.80 (46) Aperture Lens Location. Ball Catch Retainers
VF150 Series - 9601 Trim RECESSED ROUND BEVELED ACCENT 1-LIGHT TRIMLESS LED PROJECT TYPE CATALOG NUMBER Measurements in ( ) are metric equivalents. ROUND BEVELED TRIMLESS ACCENT - The VF150 Series is a
More informationLOW PROFILE 3-1/4 LED RECESSED ADJUSTABLE, DOWNLIGHT AND WALL WASH 800/1200/1500/2000 LUMEN ROUND APERTURE TC420LP, IC415LP, IC412LP, IC408LP
PRODUCT DESCRIPTION Low Profile recessed LED luminaire compatible with downlight, adjustable and wall wash trims, is less than 4 tall and produces up to 000 delivered lumens. Fixture has 45 visual cutoff
More informationRAIL 4 PERIMETER RP4D RECESSED T-BAR LED TELESCOPIC, INTEGRAL DRIVER
INSTALLATION INSTRUCTIONS RAIL 4 PERIMETER RP4D RECESSED T-BAR LED TELESCOPIC, INTEGRAL DRIVER NOTE: The following instructions provide general guidelines for product installation. For additional information
More informationINSTALLATION INSTRUCTION Indirect Recessed Channel
SAFETY INSTRUCTION IMPORTANT: NEVER attempt any work without shutting off the electricity. Read all instructions before installing. Always turn off power at fuse box prior to installation to prevent electrical
More informationTIP FOR GETTING STARTED
Tip for getting started TIP FOR GETTING STARTED Be careful not to drill into any electrical wires, ductwork, plumbing or other damagable components. If you have any questions on the locations of these
More informationInstallation Instructions for TruLine 1A Center Feed Power Channel Connector
IMPORTANT INFORMATION - This instruction must be used concurrently with other TruLine A BIY installation instructions. - This product is wall or ceiling mount. - This instruction shows a typical installation.
More informationINSTALLATION: D1-NOTCH DRYWALL TRIM FLANGE
T F W 604.549.979 604.549.9555 fluxwerx.com INSTALLATION: D1-NOTCH DRYWALL TRIM FLANGE fixture housing endcap kit optic kit join kit notch 2 cross section notch 4 cross section 4 4" 4-11/2" 4 /8 (111)
More informationSAE of 7 "R" (REGRESSED) POSITION "S" (SHIELDING AT TOP) POSITION. Tools Required
SAE 0 5/6'' Exposed TBar Ceiling FINISHED EDGE WITH JANGLE 90 IC CORNER KIT 5 7/6" 38mm 9/6'' Screw Slot TBar Ceiling "R" (REGRESSED) POSITION 6" CEILING OPENING "S" (SHIELDING AT TOP) POSITION SUPPORT
More informationPMT-L11 (for Low Ceilings) PMT-H15 (for High Ceilings)
English Français Deutsch Svenska Italiano Español Nederlands Digital Cinema Projector Ceiling Bracket PMT-L11 (for Low Ceilings) PMT-H15 (for High Ceilings) Installation Manual Be sure to read this manual
More informationINSTALLATION INSTRUCTIONS Oculux 3.5 Architectural Remodel
SAFETY INSTRUCTION IMPORTANT: NEVER attempt any work without shutting off the electricity. - Read all instructions before installing. - System is intended for installation by a qualified electrician in
More information3-1/4 LED RECESSED ADJUSTABLE AND DOWNLIGHT 800/1200/1500/2000 LUMEN SQUARE APERTURE NEW CONSTRUCTION IC/TC420LSQ, IC415LSQ, IC412LSQ, IC408LSQ
PRODUCT DESCRIPTION Recessed adjustable LED luminaire produces up to 000 delivered lumens. Fixture has 50 visual cutoff and features precision geared hot-aiming. Sealed Air-Loc housing ensures maximum
More information8.50 (216) Ball Catch Retainers 3.00 (76) Aperture Lens Location .74 (19)
VF150 Series - 8704 Trim RECESSED RECTANGULAR BEVELED ACCENT 2-LIGHT TRIMMED LED PROJECT TYPE CATALOG NUMBER Measurements in ( ) are metric equivalents. RECTANGULAR BEVELED TRIMMED ACCENT - The VF150 Series
More informationRPMSP Series Installation Guide
RPMSP Series Installation Guide Contents 1. Overview... page 1 2. Unpacking the Projector...2 3. Projector Configuration...2 4. Projector Throw Distance and Mounting...9 5. Projection Lens Focus...9 6.
More informationInstallation Instructions
Installation Instructions Follow these simple instructions to install your OneDayCab! IMPORTANT: Unpack and check shipment for damage. Verify color, size and parts before demolition. Installation of interiors
More informationInstalling your new Bevella Top. L Shaped Countertop with Joints No Finished Ends (Fits Between Four Walls)
Installing your new Bevella Top L Shaped Countertop with Joints No Finished Ends (Fits Between Four Walls) Bevella RTI Countertops are engineered and manufactured to the highest quality standards, built
More informationAssembly and Installation Guide
The Easy Hang Closet Solution SM Install Your elfa In An Instant. Enjoy The Benefits For A Lifetime. Basic Tools For elfa Assembly and Installation Level Hand or Power Drill Drill Bits 1/8", 3/8", 5/16"
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS HIGH PRESSUE LAMINATE (HPL) TOILET PARTITIONS 1030 TrimLineSeries 1040 DesignerSeries Includes continuous hardware option.65. IMPORTANT: Storage and Handling Information on last
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS MAXIMUM PRIVACY HIGH PRESSURE LAMINATE (HPL) TOILET PARTITIONS 2030 TrimLineSeries 2040 DesignerSeries IMPORTANT: Storage and Handling Information on last page. Review these instructions
More informationGeneral Installation Instructions
General Installation Instructions WARNING To reduce the risk of death, injury or property damage from fire, electric shock, cuts, abrasions, falling parts and other hazards: Service of the equipment must
More informationTASK: Replace Control Mechanism/Drive End for G71 Supervue/Everglide Vertical headrail
1. Locate the clear plastic louver stems where louvers are attached. 2. Rotate louvers open. Slide a hard plastic card between the louver and the long side of the louver stem. Push the card and louver
More informationSB-WM-ART1-M-BL. Weatherproof Universal Single-Arm Articulating Mount for Medium Displays INSTALLATION MANUAL
SB-WM-ART1-M-BL Weatherproof Universal Single-Arm Articulating Mount for Medium Displays INSTALLATION MANUAL WARNING The maximum weight of this wall mount is 90 lbs (41 kg). Use with heavier than the maximum
More information4.5 LED RECESSED FLUSH TRIM
4.5 LED RECESSED FLUSH TRIM CONCEALED RECESSED ARCHITECTURAL DOWNLIGHT Now with SORAA Vivid 95 CRI Superior performance A ceiling plane that is uninterrupted, unobtrusive, unbelievable, and now in LED.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS COMPACT LAMINATE TOILET PARTITIONS 1080 DuraLineSeries 1180 DuraLineSeries Class-A Fire Rated Includes Institutional Hardware Option.67 IMPORTANT: Storage and Handling Information
More informationINSTALLATION MANUAL PBL-UMP
INSTALLATION MANUAL PBL-UMP Table of Contents Warning Statements... 4 Parts List... 5 Installation Tools... 5 Features... 7 Projector Preparation... 8 Bracket Installation... 10 Leveling the Mounting Bracket...
More informationINSTALLATION INSTRUCTIONS - CEILING POWER TRAK, HANGER HOOKS AND RACKS I. CONTENTS CEILING POWER TRAK KIT
INSTALLATION INSTRUCTIONS - CEILING POWER TRAK, HANGER HOOKS AND RACKS I. CONTENTS CEILING POWER TRAK KIT QUANTITY DESCRIPTION 2 POWER TRAK, 5 FT LG 4 END CAPS, YELLOW 10 SCREWS, 1 5/8 LG 10 WASHERS, 5/8
More informationINSTALLATION GUIDE. Table saw or circular saw with fine-tooth blade, caulking gun, rule/tape, drill, file, hammer, plumb line/level, ridge/support.
Code: IG- Page : 1 of 6 Installation recommendations 1-Pre-Installation The recommendations provided in the bulletin represent our best judgment based on our experience with normal applications. Any deviation
More informationSUPERPLANE 2.5 INSTALLATION INSTRUCTIONS WALL/SURFACE BACK MOUNT. A nd Avenue, Unit 1 Oakland,
INSTALLATION INSTRUCTIONS SUPERPLANE 2.5 WALL/SURFACE BACK MOUNT A 1035 22nd Avenue, Unit 1 Oakland, CA 94606 P 510.489.2530 E TalkToUs@alwusa.com W alwusa.com SP2.5 - Safety & Warnings! 1. Read all instructions.
More informationEDGE Evolution Outline
EDGE Evolution Outline INSTALLATION INSTRUCTIONS Outline Installation....2-5 Outline End Filler Installation...6-9 Outline Outside Corner Installation...10-13 Outline Inside Corner Installation...14-19
More informationDRYWALL CEILING SPLINE KICKER REFLECTOR DIFFUSER LENGTH TABLE DIFFUSER LENGTH TABLE DESCRIPTION 2' IND 3' IND 4' IND 6' IND 8' IND
SUPPLEMENTAL INSTALLATION TYPE LG-WWD-44, R-WWD-44 & RP-WWD-44 510553-2000 WHICH IS CONTRARY TO THE CONTAINED HEREIN. P/C PG. 1 OF 1 1/4-20 THREADED ROD OR EQUAL SUPPLIED PANHEAD SHEET METAL SCREW HEX
More informationINSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS
FOR RECESSED EDGE-LIT LED EXIT SIGN Standard and New York Approved Models (Emergency, non-emergency and X2 Dual Circuit operation) READ AND FOLLOW ALL SAFETY INSTRUCTIONS IMPORTANT SAFEGUARDS: When using
More informationAperture Lens Location Ball Catch Retainers
VF150 Series - Trim RECESSED SQUARE FLAT ACCENT 1-LIGHT TRIMLESS HI-EFFICIENCY LED PROJECT TYPE CATALOG NUMBER Measurements in ( ) are metric equivalents. SQUARE FLAT TRIMLESS ACCENT - The VF150 Series
More informationHP 2 SERIES Integral Driver - Solid State LED
HP 2 SERIES Installation Instructions Warning High Voltage Hot Surface NEEDED FOR INSTALLATION: By Others 1/8 & 5/32 Allen Wrench Waterproof Wire Connectors Level Phillips Screwdriver IMPORTANT - WEAR
More informationIMPORTANT: installation. FLOOR ANCHORED CEILING HUNG OVERHEAD BRACED FLOOR-TO- CEILING ANCHORED
INSTALLATION INSTRUCTIONS MAXIMUM PRIVACY COMPACT LAMINATE TOILET PARTITIONS 2080 DuraLineSeries 2180 DuraLineSeries Class-A Fire Rated Includes Institutional Hardware Option.67 IMPORTANT: Storage and
More informationInstallation Instructions
Installation Instructions For Models: Model Number / Description File Name 1540 Classic Series P-Lam Toilet Partitions 1540.pdf 1 INSTALLATION INSTRUCTIONS LAMINATED PLASTIC TOILET PARTITIONS 1540 Classic
More informationGeneral Installation Instructions LED
General Installation Instructions LED To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions and other hazards, please read all warnings
More informationArriva. Concealed frame doorsets. Installation instructions
Arriva Concealed frame doorsets 1 2 Installation instructions 3 Thank you for choosing Arriva To ensure the installation process is simple and efficient we recommended you read this guide in full before
More informationflat panel solutions Specifications Box contents Warnings CAUTION: Tilt Wall Mount for LCD, Plasma, and LED Displays Instruction Manual
flat panel solutions Tilt Wall Mount for LCD, Plasma, and LED Displays Instruction Manual MST65BKR Fits TVs 37-65 Maximum Load Capacity 165 lb (75kg) Specifications Display Size: 37 to 65 Maximum Load:
More informationINSTALLATION MANUAL PBC-UMS
INSTALLATION MANUAL. PBC-UMS Premier Mounts 3130 E. Miraloma Avenue Anaheim, CA 92806 Phone: (800) 368-9700 Fax: (800) 832-4888 mounts@mounts.com www.mounts.com Rev. 01 PBL-110 Projector Mount Page 2 Installation
More informationSLOT INSTALLATION GUIDE Indoor IP20
Please read entire guide prior to starting installation. Sections: Pre-Installation Single Run Fed From Both Ends NOTES 1. IP40 and lower tape must be installed indoors only. Installing outdoors will void
More informationAXIOM Classic Trim Installation Instructions
CEILING SYSTEMS AXIOM Classic Trim Installation Instructions 1 GENERAL 1.1 Description Axiom is a perimeter trim system designed for use with most of Armstrong s suspension systems. It is available through
More informationSB-WM-ART2-L-BL SB-WM-ART2-XL-BL
SB-WM-ART2-L-BL SB-WM-ART2-XL-BL Weatherproof Universal Dual-Arm Articulating Mount for Large TVs INSTALLATION MANUAL WARNING The maximum weight of this wall mount is 150 lbs (68.04 kg). Use with heavier
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS HIGH PRESSUE LAMINATE (HPL) TOILET PARTITIONS 1030 TrimLineSeries 1040 DesignerSeries Includes continuous hardware option.65. IMPORTANT: Storage and Handling Information on last
More informationSafety cable 5.00 (127) Ø5.50 (140) N Narrow M Medium W Wide. N Narrow 14 M Medium 30 W Wide 40 V Very Wide 70
VF100C Bullseye Series - 8121C Trim ROUND ADJUSTABLE ACCENT DOWNLIGHT 1-LIGHT TRIMMED LED MEDIUM PROJECT 8121C Measurements in ( ) are metric equivalents. TYPE CATALOG NUMBER ROUND GIMBAL ADJUSTABLE TRIMMED
More informationInstallation And Care Instructions. Vertical Honeycomb Shades
Installation And Care Instructions Vertical Honeycomb Shades Rev 5/2013 Table Of Contents Getting Started... 3 Parts Overview... 4 Materials Required... 5 Tools Required... 6 Outside Mount Installation...
More informationSeriesTWO RGB Fluorescent Fixtures. Installation and Instruction Manual
SeriesTWO RGB Fluorescent Fixtures Installation and Instruction Manual Brightline LP 580 Mayer Street #7, Bridgeville PA 15017 Phone 1-412-206-0106 Fax 1-412-206-0146 www.brightlines.com The Brightline
More informationFigure A. Figure B. Figure C. Figure D
Xsite 1 Power/Data Tile and Components Tools Required Tape Measure Cordless Drill/Driver #2 Phillips Screw driver bit Rubber Mallet Flat Blade Screwdriver Figure A Hardware Required Provided as shown Installation
More informationINSTALLATION AND CARE INSTRUCTIONS
INSTALLATION AND CARE INSTRUCTIONS Vertical Applications Honeycomb Shades CONTENTS Introduction...2 Before You Begin...3 Vertical Application Parts Overview...4 Materials Required...5 Tools Required...6
More informationBionic 4 PERIMETER, CONTINUOUS RUN X3, X7
I NSTALLAT ION INSTRUC TIONS 6 3 /4 6 3 /4 3¾ 5 1 /2 For LP installs, ceiling opening is equal to row length + 3 /4 8 1 /2 4 3 /32 5 1 /4 Flush X7 Shown PARTS SHIPPED SEPARATELY 4 3 /32 5 1 /4 3" Regressed
More informationTOGGLER Specialty Anchors
TOGGLER Specialty Anchors Description All TOGGLER Specialty Anchors can be used in any material (concrete, plywood, paneling, drywall, etc.) of any thickness above their minimum grip range. All TOGGLER
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SOLID PHENOLIC TOILET PARTITIONS 1080 DuraLineSeries Class-A Fire Rated Includes Institutional Hardware Option.67 IMPORTANT: Storage and Handling Information on last page. Review
More informationInstallation Guide. SN-LM42 Brilliance Series Photoluminescent Area of Rescue Signs
Installation Guide SN-LM42 Brilliance Series Photoluminescent Area of Rescue Signs This series consists of the following: Model SN-LM42D Model SN-LM42DR Model SN-LM42S Model SN-LM42SR CAUTION: In order
More informationHospital Grade Welded Ceiling System
MANUAL INSTALLATION Hospital Grade Welded Ceiling System HGWC Series v001 Issue Date: 08/14/18 2018 Price Industries Limited. All rights reserved. TABLE OF CONTENTS Product Overview Before You Start...1
More informationARCHITECTURAL. 2" Round and Square ARCHITECTURAL DOWNLIGHTS NEW CONSTRUCTION AND REMODEL PATENT PENDING
ARCHITECTURAL 2" Round and Square ARCHITECTURAL DOWNLIGHTS NEW CONSTRUCTION AND REMODEL PATENT PENDING 2" Round and Square Architectural Recessed Downlight Solutions Downlight Wall Washer Adjustable Accent
More information