Round or Square Type IC Down Light Housing with LED Lamp for Flangeless Trims E3_L_-L_DI 1.4
|
|
- Pierce Hudson
- 5 years ago
- Views:
Transcription
1 Installation Instructions for 90ELED-DIC Round or Square Type IC Down Light Housing with LED Lamp for Flangeless Trims E_L_-L_DI. LED - ROUND/ SQUARE FLANGELESS GENERAL PRODUCT I NFORMATION: This product is suitable for indoor locations. This product can be dimmed with a standard electronic dimmer. This instruction shows a typical installation. CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90 c supply conductors. Install the Housing with Adjustable Bars A B HOUSING NAIL ½ to ¾ LEAVE TAB IN PLACE ¾ or thicker NOTE: Skip this section if installing the housing with butterfly brackets. BREAK OFF AND DISCARD OUTER ADJUSTABLE BAR INNER ADJUSTABLE BAR HOUSING CLASP STOP POINT Keep Tab for ceiling ½ to ¾ thick. When using adjustable hanger bars with ½ to ¾ thick ceilings, leave the tab of the hanger bars in place. Break off Tab for ceiling ¾ or thicker. When using adjustable hanger bars with ¾ or thicker ceilings, remove the tab by bending it at the perforation. TAB Slide the inner adjustable bar completely through the three housing clasps. Make sure the nail is on top. Slide and push the outer adjustable bar completely onto the inner adjustable bar so that the tab clicks into place behind the stop point.this will prevent the adjustable bars from coming apart. Repeat steps & for the other side of the housing.
2 C JOIST D NAIL HOUSING NOTCH ADJUSTABLE BAR NOTE: The adjustable bars can be mounted to joists that are spaced " - " apart. Align the bottom of the end plates with the bottom of the ceiling joists. Level the adjustable bars and, with a hammer, tap the nails completely into the joists to secure the adjustable bars in place. HOUSING NOTCH Adjust the trim holder position (horizontal position) by sliding the housing on adjustable bars. When the desired location is achieved, tighten the two # self tapping screws to lock the housing onto the adjustable bars. NOTE: Notches in trim holder can be used to align multiple housings using a laser or string.
3 Install the Housing with Butterfly Brackets Connect Power to the Housing A NOTCH A TAB ELECTRICAL BOX COVER BUTTERFLY BRACKET WING NUT NOTE: Skip this section if installing the housing with adjustable bars. Push the tab on the housing electrical box up and remove the electrical box cover. Slightly loosen the wing nut to slide the butterfly bracket up or down. After achieving the proper location, tighten the wing nut to secure the butterfly bracket in place. Repeat steps and on for the other butterfly bracket. B CONDUIT Utilize the butterfly brackets to install the housing in accordance with local electrical codes. NOTE: Notches in trim holder can be used to align multiple housings using a laser or string. Install the conduit to the housing electrical box. Run the power line wires into the housing electrical box. WARNING: RISK OF FIRE: When using the housing electrical box for power feed through, use MAX - # AWG, or - # AWG branch circuit wires.
4 Install Drywall and Plaster Ring C A -/" -/" ROUND SQUARE Connect the neutral power line wire to the white transformer wire with a wire nut. Connect the hot power line wire to the black transformer wire with a wire nut. For round trims, mark a -/" diameter circle on drywall. Cut out the marked section. For square trims, mark a -/" square on drywall. Cut out the marked section. Make sure that housing is grounded in accordance with local electrical codes. B Replace the electrical box cover. Make sure that the top edge of the cover snaps under the tab. DRYWALL JOIST Align the cut out section of drywall with the trim holder and install drywall.
5 C TAB TAB D #- SCREW #- SCREW ROUND PLASTER RING SQUARE PLASTER RING Secure the plaster ring in place with the two provided flat head #- screws. Make sure that the screws penetrate through the drywall into the housing screw holes. NOTE: Do not overtighten the screws! Overtightening may bend the plaster ring, causing the plaster surface to come away from the drywall. E CUT OUT CUT OUT Line up the two tabs in back of the plaster ring with the two cut out sections of the trim holder inside edge. Push the plaster ring tabs into the cut out sections of the trim holder edge. Plug the trim holder with the provided dust shield. Properly plaster onto the plaster ring and drywall. F Finish around the trim to match drywall.
6 Replacing the Lamp A C BACK VIEW SIDE VIEW C AUTION:To reduce the risk of a burn or electric shock during relamping, disconnect the power to the fixture. Place the lamp assembly on a clean, flat surface with the lamp side down. Remove the trim from the fixture. Loosen and remove all four screws on the back of the lamp assembly and set them aside. B Loosen all three screws from the lamp assembly and lower the lamp assembly. CONNECTOR ( INSIDE) D FRONT COVER LAMP HEATSINK PLUG Hold the lamp assembly together and flip it over. Lift the front cover off. Pull the old lamp out. POWER CONNECTOR POWER PLUG 9 0 Use ONLY WATT proprietary Element Lighting LED lamp. Peel the liner off the thermal pad on the new lamp. Line up the square and round pegs in the new lamp with the holes in the heatsink and push the new lamp into place. Replace the front cover. Place the lamp assembly on a clean, flat surface with the lamp side down and reinstall the screws into the back. Reconnect the power plug and reinstall the lamp assembly into the housing. Reinstall the trim. Disconnect the lamp power plug from the connector inside the housing on the electrical box side.
7 NOTES
8 STATEMENT OF WARRANTY Tech Lighting warrants all products manufactured by Tech Lighting to be free from defects in material and workmanship under normal use for a specified period after the date of original purchase as follows: years for LED products; years for Energy Star qualified products; year for all other products. For details, visit our website at: SAVE THESE INSTRUCTIONS! 00 Linder Ave, Skokie, IL Tech Lighting, L.L.C. All rights reserved.the "Element" graphic is a registered trademark of Element. Element reserves the right to change specifications for product improvements without notification. A Generation Brands Company
Round or Square Chicago Plenum Down Light Housing with Lamp
Installation Instructions for 90ELED-DCP Round or Square Chicago Plenum Down Light Housing with Lamp LED E_-L_DC. LED - ROUND/ SQUARE GENERAL PRODUCT I NFORMATION: This product is suitable for indoor locations.
More informationRound or Square Type IC Wall Wash Housing with Lamp for Flangeless Trims
Installation Instructions for 90ELED-WIC Round or Square Type IC Wall Wash Housing with Lamp for Flangeless Trims LED E_L_-L_WI. LED - ROUND/ SQUARE FLANGELESS GENERAL PRODUCT I NFORMATION: This product
More informationwith Lamp Install the Housing with Adjustable Bars Installation Instructions for LED E3_-L_DN 1.1 ½ to ¾ ¾ or thicker
Installation Instructions for 90ELED-D Round or Square Type IC, Non-IC Down Light Housing with Lamp LED E_-L_DN. LED - ROUND/ SQUARE GENERAL PRODUCT I NFORMATION: This product is suitable for indoor locations.
More informationInstall the Housing. Installation Instructions for Entra Round or Square Type IC, Air-tight New Construction Adjustable LED Housing EN3_-LH9_ 1.
Installation Instructions for Entra Round or Square Type IC, Air-tight New Construction Adjustable LED Housing 90ENTRA EN_-LH9_. LED - ROUND/ SQUARE GENERAL PRODUCT I NFORMATION: This product is safety
More informationMultiples EM_ 1.4. Install 1X1/1X2/1X3/1X4 Housings. Installation Instructions for. This product is suitable for indoor locations.
Installation Instructions for 90EMULTI Multiples EM_. GENERAL PRODUCT I NFORMATION: This product is suitable for indoor locations. This product can be dimmed with a standard electronic dimmer or a 0-0V
More informationReflections Housing with EldoLED and Lutron Hi-lume Drivers EDIHE_ 1.4
Installation Instructions for 90EDIHE Reflections Housing with EldoLED and Lutron Hi-lume Drivers EDIHE_.4 LED GENERAL PRODUCT I NFORMATION: This product is suitable for indoor locations. This product
More informationPrepare the Fixture. Sage 37 Bath. Back Plate Installation (Horizontal) Installation Instructions for 700BCSAGW37_
Installation Instructions for Sage Bath 00BCSAGW_ 90BCSAGEL.0 BATH COLLECTION GENERAL PRODUCT I NFORMATION: This fixture is intended to be installed utilizing NEC compliant junction boxes. This product
More informationMicro Channel. Shorten the Fixture (optional) Installation Instructions for 700UMCD_ UNILUME. This product is suitable for damp locations.
Installation Instructions for Micro Channel 700UMCD_ 90MICRO. UNILUME GENERAL PRODUCT I NFORMATION: This product is suitable for damp locations. This product can be dimmed with a low-voltage electronic
More informationINSTALLATION: D1-NOTCH DRYWALL TRIM FLANGE
T F W 604.549.979 604.549.9555 fluxwerx.com INSTALLATION: D1-NOTCH DRYWALL TRIM FLANGE fixture housing endcap kit optic kit join kit notch 2 cross section notch 4 cross section 4 4" 4-11/2" 4 /8 (111)
More information+ - 1a. 1b. c. 1d. 1e. Runway Suspended / Surface Cont. Run Installation. 2.0mm DIL DIL Revision - M 23/11/2018 Page 1
230-240V / 50-60Hz IP20 IK00 + - 2.0mm WARNING - THIS LUMINAIRE MUST BE EARTHED This luminaire has been tested and is manufactured to comply with BS EN 60598 : specification for general requirements and
More informationDOWNLIGHT LED SERIES INSTALLATION INSTRUCTIONS
WARNING: This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Make sure all
More informationINSTALLATION INSTRUCTIONS Xenix Incandescent Series XN12, XN24, XN36, XN48
INSTALLATION INSTRUCTIONS Xenix Incandescent Series XN12, XN24, XN36, XN48 IMPORTANT SAFETY INSTRUCTIONS ---- CAUTION! --- READ THIS FIRST 11500 Melrose Avenue Franklin Park, Illinois 60131 Phone: 847-451-0700
More informationInstallation and Assembly: Articulating Swivel Arm for 37" - 60" Flat Panel Displays
Installation and Assembly: Articulating Swivel Arm for 37" - 60" Flat Panel Displays Models: PLA60, PLA60-S, PLAV60, PLAV60-S Max UL Load Capacity: 175 lb (79 kg) 2300 White Oak Circle Aurora, Il 60502
More informationInstallation Instructions For Aurora Dual MR16 Round & Square Edge 3.3" Fig.1 Complete Fixture ADJUSTABLE GEARS HIDDEN BEHIND THE LAMP PAN LOCK
2015 Pure Lighting. All Rights Reserved. Installation Instructions For Aurora Dual MR16 Round & Square Edge 3.3" 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1195 Fax: 773-935-5613 www.purelighting.com
More informationPower Vault Adapter. Install the Power Vault Adapter to MonoRail Power Feed Canopies & Recessed Can Transformer. Installation Instructions for
Installation Instructions for Power Vault Adapter 00MOPVLT_ 0MOVALT. SPECIAL INSTALLATION GENERAL PRODUCT I NFORMATION: This product is suitable for indoor dry locations only. This product is intended
More informationTHIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
LumeLEX 2026 SERIES INSTALLATION INSTRUCTIONS Important THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Warning This product must be installed in accordance with National Electrical
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationINSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS
FOR RECESSED EDGE-LIT LED EXIT SIGN Standard and New York Approved Models (Emergency, non-emergency and X2 Dual Circuit operation) READ AND FOLLOW ALL SAFETY INSTRUCTIONS IMPORTANT SAFEGUARDS: When using
More informationInde-Pendants Family. 32L Ring Plaster Trim, Grid and Drywall Ceiling Types. Document No Installation instructions for 32L-Rxx-P
Inde-Pendants Family 32L Ring Plaster Trim, Grid and Drywall Ceiling Types Installation instructions for 32L-Rxx-P Document No. Supplied by Litecontrol 32L Inde-Pendants: Ring (Plaster Trim, Grid and Drywall
More informationINSTALLATION INSTRUCTION Silo Multiples - New Construction Housing MT-4*15, MT-4*10
IMPORTANT SAFETY INSTRUCTIONS 1. Read all instructions before installing. 2. System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations.
More informationGeneral Installation Instructions
General Installation Instructions WARNING To reduce the risk of death, injury or property damage from fire, electric shock, cuts, abrasions, falling parts and other hazards: Service of the equipment must
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Universal Low Profile Tilt Mount Model: U.S. Toll Free: 1-866-752-6271 Outside N. America: 1-503-748-5799 E-mail: ts@planar.com FRANCE Phone: +33 5 6378 3810 E-mail: emeats@planar.com
More informationInde-Pendants Family. 32L Surface Mount Cylinder with Ring Plaster Trim, Grid and Drywall Ceiling Types. Document No
Inde-Pendants Family 32L Surface Mount Cylinder with Ring Plaster Trim, Grid and Drywall Ceiling Types Installation instructions for 32L-CRxx-S-D Document No. Supplied by Litecontrol 32L Inde-Pendants:
More informationINSTALLATION INSTRUCTIONS
Sheet 1 of 5 General: Upon receipt of fixture thoroughly inspect for any freight damage, which should be brought to the attention of the delivery carrier. Compare the catalog description listed on the
More informationInstalling Fixture Using Remote Power Supply
2017 Edge Lighting. All Rights Reserved. 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1195 Fax: 773-935-5613 www.edgelighting.com info@edgelighting.com 904-BV2-2K4K-_03 BV2-1RE-_-2K4K-_ Installation
More informationC 0.05" ALLEN WRENCH. Installation Instructions for Cirrus Channel Suspension T1 with 4" Square or Round Canopy. Section One: Adjusting Cable Position
Doc # 90-CST-SQ_0 W. Fullerton Chicago, IL 0 Ph:.0.9 Fax:.9. www.pureedgelighting.com info@pureedgelighting.com 0 PureEdge Lighting. All Rights Reserved. Installation Instructions for Cirrus Channel Suspension
More informationINSTALLATION INSTRUCTIONS
CREATING POSITIVE CUSTOMER EXPERIENCES INSTALLATION INSTRUCTIONS Universal Low Profile Tilt Mount for 42 to 63 Flat Panels NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone:
More informationSea Doo Spark Engine Access Kit
Sea Doo Spark Engine Access Kit PART# - RS4-130-EAK APPLICATION(S): Sea Doo Spark. 2up & 3up Models. We strongly recommend the use of a service manual to familiarize yourself with the various components
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Universal Low Profile Flat Mount Model: U.S. Toll Free: 1-866-752-6271 Outside N. America: 1-503-748-5799 E-mail: ts@planar.com FRANCE Phone: +33 5 6378 3810 E-mail: emeats@planar.com
More informationInstallation and Assembly: In-wall Mount for 32" to 71" Flat Panel Displays
Installation and Assembly: In-wall Mount for 32" to 71" Flat Panel Displays Model# Display size range IM760P, IM760P-S 32" to 71" (81 to 180 cm) IM760PU, IM760PU-S 32" to 65" (81 to 165 cm) This product
More informationLIGHT FIXTURES MUST BE COMPLETELY INSTALLED PRIOR TO CEILING CONSTRUCTION
CAUTION: BEFORE BEGINNING INSTALLATION REVIEW LAYOUT DRAWINGS, AND SHIPMENT. MAKE SURE ALL LIGHT S AND MATERIALS ARE ON SITE AND READILY ACCESSIBLE. IF ANY ICON MATERIALS ARE MISSING, CONTACT ICON INTERNATIONAL
More informationInstallation Instructions For Aurora Halogen Accent Housing 3 Round & Square Trimless AH1-ARE, AH1-ARB, AH1-ASE, AH1-ASB. Fig.
2015 Pure Lighting. All Rights Reserved. Installation Instructions For Aurora Halogen Accent Housing 3 Round & Square Trimless AH1-ARE, AH1-ARB, AH1-ASE, AH1-ASB 1718 W. Fullerton Ave Chicago, IL 60614
More informationInstallation Instructions for Cirrus Suspension Downlight with Power - End Feed. Section One: 4" Flush Canopy Version
Doc # 0-CSP-E_0 W. Fullerton Chicago, IL 606 Ph:.0. Fax:..6 www.pureedgelighting.com info@pureedgelighting.com 06 PureEdge Lighting. All Rights Reserved. Installation Instructions for Cirrus Suspension
More informationGeneral Installation Instructions LED
General Installation Instructions LED To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions and other hazards, please read all warnings
More informationJoiner Kit Joiner bracket (x1) Biscuit aligners (x2) Trim Flange
- Trim System Overview These instructions review how to install TruGroove Perimeter fixtures. Modules can be installed as individual standalone units, or they can be joined together to create continuous
More informationTIP FOR GETTING STARTED
Tip for getting started TIP FOR GETTING STARTED Be careful not to drill into any electrical wires, ductwork, plumbing or other damagable components. If you have any questions on the locations of these
More informationEOS LED Surface Mounted Luminaire
Installation Instruction Sheet INSTALLATION INSTRUCTIONS FOR JOINING AND SUSPENDING FIXTURES WARNING WARNING To reduce the risk of death, injury or property damage from fire, electric shock, cuts, abrasions,
More informationINSTALLATION INSTRUCTIONS FOR FLUSH MOUNT FIXTURES
Kurt Versen Company Point Source Lighting Models with Round Apertures 10 Charles Street Westwood, New Jersey 1 PLEASE READ THIS ENTIRE INSTRUCTION SHEET BEFORE INSTALLATION. 2 DISCONNECT ELECTRICAL POWER
More informationInstallation Instructions For Aurora Halogen Accent Housing 3 Round & Square Trimless AH2-ARE3 & AH2-ASE3. Fig.1 Complete Fixture
015 Pure Lighting. All Rights Reserved. Installation Instructions For Aurora Halogen Accent Housing 3 Round & Square Trimless AH-ARE3 & AH-ASE3 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1195
More informationInstallation and Assembly: In-wall Mount for 32" to 71" Flat Panel Screens
Installation and Assembly: In-wall Mount for 32" to 71" Flat Panel Screens Model# IM760P, IM760P-S IM760PU, IM760PU-S Screen size range 32" to 71" (81 to 180 cm) 32" to 60" (81 to 152 cm) IM760P IM760P-S
More informationB235 Mobius Sconce Page 1 of 6
Mobius Sconce 28-9450 Page 1 of 6 CAUTION: FAILURE TO INSTALL THIS PRODUCT PROPERLY MAY RESULT IN PERSONAL INJURY OR PROPERTY DAMAGE. We recommend installation by a qualified individual trained in the
More informationINSTALLATION INSTRUCTIONS REPLACING EXISTING DEADBOLT ASSEMBLY
INSTALLATION INSTRUCTIONS REPLACING EXISTING DEADBOLT ASSEMBLY A B C L M N D E F G O P Q H I J Tools provided in Amesbury installation kit: (A) door router fixture, (B) doorframe router fixture, (C) ½
More informationConnecting the Channel A
20 Edge Lighting. All Rights Reserved. Installation Instructions for Cirrus Channel Suspension T, Tubular Lens w/2sq or 2RD Canopy IMPORTANT INFORMATION - This product is suitable for indoor locations.
More informationMaxLite Linear Strip ECO Series
General Safety Information To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings and instructions
More informationFigure A. Figure B. Figure C. Figure D
Xsite 1 Power/Data Tile and Components Tools Required Tape Measure Cordless Drill/Driver #2 Phillips Screw driver bit Rubber Mallet Flat Blade Screwdriver Figure A Hardware Required Provided as shown Installation
More informationSeriesTWO RGB Fluorescent Fixtures. Installation and Instruction Manual
SeriesTWO RGB Fluorescent Fixtures Installation and Instruction Manual Brightline LP 580 Mayer Street #7, Bridgeville PA 15017 Phone 1-412-206-0106 Fax 1-412-206-0146 www.brightlines.com The Brightline
More informationINSTALLATION INSTRUCTIONS FOR FLUSH MOUNT FIXTURES
Kurt Versen Company Point Source Lighting 10 Charles Street Westwood, New Jersey Models with Square or Rectangular Apertures 1 PLEASE READ THIS ENTIRE INSTRUCTION SHEET BEFORE INSTALLATION. 2 DISCONNECT
More informationInterra Installation Manual
Interra Installation Manual Instructions to install the Friant Interra panel system Friant & Associates, LLC Table of Contents Getting Started Introduction... 3 General Tools, Staging & Safety... 4 Before
More informationSM-RAZOR-T-M/L/XL. Strong Low Profile Tilt Mount for Ultra-Thin Flat-Panel TVs INSTRUCTION MANUAL
SM-RAZOR-T-M/L/XL Strong Low Profile Tilt Mount for Ultra-Thin Flat-Panel TVs INSTRUCTION MANUAL WARNINGS: Installation of this product should be done by a qualified professional. Do not begin installation
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationInigo Sconce INSTALLATION INSTRUCTIONS P _2_A 1 of 5
P31321 1 of 5 Thank You For Choosing Kallista We appreciate your commitment to Kallista quality products. Please take a moment to review this manual before you install your Kallista product. If you encounter
More informationMantelMount. TM1A Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
MantelMount TMA Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS TM Thank you for choosing the MantelMount television wall mount. Please read this entire manual before
More information3% VOLTAGE DROP. Installation Instructions for 400 Watt 24 Volt DC RGB DMX LED Power Supply SAVE THESE INSTRUCTIONS!
Installation Instructions for 400 Watt 24 Volt DC RGB DMX LED Power Supply Doc # 904-PSB-400W-24VDC_06 1718 W. Fullerton Chicago, IL 60614 Ph: 773.770.1195 Fax: 773.935.5613 www.pureedgelighting.com info@pureedgelighting.com
More informationH2-50 Hydrogen Generator Field Update
This field update is intended to provide extra protection in the event the H2 generation cell fractures or cracks. Please add the additional parts to your H2-50 as soon as possible. Please take a digital
More informationMM540 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
MM50 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.
More informationSM-RAZOR-F-M/L/XL. Strong Low Profile Fixed Mount for Ultra-Thin Flat-Panel TVs INSTALLATION MANUAL
SM-RAZOR-F-M/L/XL Strong Low Profile Fixed Mount for Ultra-Thin Flat-Panel TVs INSTALLATION MANUAL WARNINGS: Installation of this product should be done by a qualified professional. Do not begin installation
More informationInstallation Instructions
Installation Instructions Self-Cleaning Radiant Trivection Electric Slide-In Range JS998 Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: www.geappliances.com BEFORE YOU BEGIN Read
More informationInstallation Instructions For Aurora Halogen Accent Housing 3 Round & Square Trimless AH2-ARE3 & AH2-ASE3. Fig.1 Complete Fixture
015 Pure Lighting. All Rights Reserved. Installation Instructions For Aurora Halogen Accent Housing 3 Round & Square Trimless AH-ARE3 & AH-ASE3 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1195
More informationLINESSE LINEAR LUMINAIRE 3 RECESSED CV2424
Linesse Linear Luminaire 3 Recessed LINESSE LINEAR LUMINAIRE 3 RECESSED Page 2: Warnings Page 3: Mounting Types and Dimensions Page 4: T-Grid and Joining Fixtures Page 5: Hard Ceiling and Joining Fixtures
More informationZIP CLOUD SUSPENDED INSTALLATION MANUAL
ZIP CLOUD SUSPENDED INSTALLATION MANUAL www.delviro.com info@delviro.com 1.877.502.3434 SAFETY NOTE: Follow the Electrical Codes of the Country where this fixture will be installed. For Canada follow the
More informationINSTALLATION RECOMMENDATIONS For The Con-Tech ODYSSEY Line Voltage Flexible Track System
INSTALLATION RECOMMENDATIONS For The Con-Tech ODYSSEY Line Voltage Flexible Track System IMPORTANT SAFETY INSTRUCTIONS: Read all instructions before installation. Save these instructions for later use.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS P4263F Universal Low Profi le Flat Mount for 42 to 63 Flat Panels NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 1.800.368.9700 Fax: 1.800.832.4888
More informationAURORA HALOGEN ACCENT HOUSING 3 ROUND AND SQUARE TRIMLESS AH3-ARE3-RBG & AH3-ASE3-RGB INSTALLATION INSTRUCTIONS
AURORA HALOGEN ACCENT HOUSING 3 ROUND AND SQUARE TRIMLESS AH3-ARE3-RBG & AH3-ASE3-RGB INSTALLATION INSTRUCTIONS Fixtures must be installed by a qualified electrician (check with local and national codes
More informationInstallation Instructions for Zip Suspension Downlight with Remote Power and 4" Square or Round Canopy
Doc # 90-ZS-SQ_0 W. Fullerton Chicago, IL 0 Ph:.0.9 Fax:.9. www.pureedgelighting.com info@pureedgelighting.com 0 PureEdge Lighting. All Rights Reserved. Installation Instructions for Zip Suspension Downlight
More informationAssembly Instructions
InTandem Table System November 20 InTandem Table System - Worksurface #4 x/" 4 wood screw power beam Tools Provided T-0 Extended Torx Driver T-25 Torx Driver Additional Tools Required Soft protective
More informationPAM-200 Universal Projector Mount
INSTALLATION MANUAL PAM-200 Universal Projector Mount Sony Electronics 16540 West Bernardo Drive San Diego, CA 92127 www.sony.com IN-PAM200.R0 Table of Contents Parts List...- 3 - Installation Tools...-
More informationEPPA2-KIT DUAL MONITOR ARM CONVERSION
EPPA2-KIT DUAL MONITOR ARM CONVERSION EPPA2-KIT Rev A 10/17 Model EPPA2-KIT-XXX ASSEMBLY AND ADJUSTMENT EPPA2-KIT PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and adjustment
More informationLine volt rail & fixtures. Low volt quick connect fixtures with transformers
INSTRUCTIONS: Line Volt Flexrail2 Safety Instructions: A qualified electrician must install system only. System is intended for installation in accordance with National Electric Code, local and Federal
More informationInde-Pendants Family. 32L Surface Mount Cylinder Plaster Trim, Grid and Drywall Ceiling Types. Document No
Inde-Pendants Family 32L Surface Mount Cylinder Plaster Trim, Grid and Drywall Ceiling Types Installation instructions for 32L-C-S-D Document No. Supplied by Litecontrol 32L Inde-Pendants: Cylinder (Surface
More informationInstallation and Assembly: Projector Ceiling/Wall Mount
Installation and ssembly: Projector Ceiling/Wall Mount Models:PRG-EX, PRG-EX-S, PRG-EX-W PRG-EXB, PRG-EXB-S, PRG-EXB-W PRG-EXC, PRG-EXC-S, PRG-EXC-W R This product is intended for use with UL Listed products
More informationEOS Direct/Indirect LED Pendant Luminaire
Installation Instruction Sheet INSTALLATION INSTRUCTIONS FOR JOINING AND SUSPENDING FIXTURES WARNING WARNING To reduce the risk of death, injury or property damage from fire, electric shock, cuts, abrasions,
More informationLINESSE LINEAR LUMINAIRE 3 CEILING MOUNT CM2420
Linesse Linear Luminaire 3 Ceiling Mount LINESSE LINEAR LUMINAIRE 3 CEILING MOUNT Page 2: Warnings Page 3: Mounting Configurations Page 4: Power Feed Page 5: Surface Mounting Page 6: Threaded Rod Mounting
More information7878 K940. Checkpoint Antenna. Kit Instructions. Issue B
7878 K940 Checkpoint Antenna Kit Instructions Issue B Revision Record Issue Date Remarks A July 7, 2009 First issue B Nov2013 Revised the Checkpoint installation procedures for 7878 and 7874 scanners Added
More informationINDIVIDUAL MOUNTING: T-Bar
X1 (T-BAR) INSTALLATION INSTRUCTIONS GENERAL NOTES NOTE : Additional support to structural member may be required. Check with local building codes for requirement. 1. Place troffer clamp approx. 6 from
More informationInstalling and Upgrading Internal Modules in Cisco 1800 Series Routers (Modular)
CHAPTER Installing and Upgrading Internal Modules in Cisco 800 Series Routers (Modular) This chapter describes how to install or upgrade modules that are located internally within the Cisco 800 series
More informationFACTORY CAT TOMCAT CORPORATION
FACTORY CAT RPS TOMCAT CORPORATION Artificial Turf and Carpet Sweeping Install Kit #349-641 & #349-642 1. Detach batteries so that there is no power running through the machine before starting. 2. Start
More informationNOVA-EXT Versatile Projector Mount Model: NOVA-EXT
INSTALLATION MANUAL NOVA-EXT Versatile Projector Mount Model: NOVA-EXT NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 800-368-9700 Fax: 800-832-4888 Other Locations
More information-Always de-energize the circuit and/or equipment before connecting to, disconnecting from or servicing the equipment.
W3 Direct and W3 Indirect/Direct Series Products WARNING To Reduce Risk Of Death, Injury Or Property Damage From Fire, Electric Shock And Other Hazards: -Service of equipment must be performed by qualified
More informationSAVE THESE INSTALLATION INSTRUCTIONS
Light Without Boundaries LUMATO RESERVES THE RIGHT TO CHANGE PRODUCT 7500003 8/4 Light Without Boundaries LUMATO RESERVES THE RIGHT TO CHANGE PRODUCT GENERAL INSTALLATION WARNING To Reduce Risk Of Death,
More informationP /8 Ring Diameter 90. Trim Ring Mounting Holes P /8. 393/16 Ring Diameter. Stud Minimum
PARTS LIST VARIABLE Top Over Head Support Bracket 1 872070 P4000-SMR Over Head Joiner Bracket 1 VARIABLE Bottom Over Head Bracket 1 79741 P4000-SMR 4 Angled Leg 4 100-00230-14 1/4-20 x 31/2 RD. HD. MS.
More informationINSTALLATION INSTRUCTIONS IMPORTANT SAFEGUARDS SAVE THESE INSTRUCTIONS INSTALLATION INSTRUCTIONS
MILLENIUM ROUND Luminaire for High Abuse Applications SEMI-RECESSED PROFILE SERIES INSTALLATION INSTRUCTIONS 1 IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always
More informationInstallation Instructions for TruLine 1.6A 24VDC. Section One: Basic Configuration Options
Doc # 902-TL1.6A_07 1718 W. Fullerton Chicago, IL 60614 Ph: 773.770.1195 Fax: 773.935.5613 www.pureedgelighting.com info@pureedgelighting.com 2016 PureEdge Lighting. All Rights Reserved. Installation Instructions
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Universal Swingout Arm Model: AM300/AM300-B NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 1.800.368.9700 Fax: 1.800.832.4888 Other Locations
More informationPlease read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment.
2005-08 Pontiac G6 GT Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed
More informationInstallation and Assembly: Flat Panel Pull-out Swivel Wall Mount
Installation and ssembly: Flat Panel Pull-out Swivel Wall Mount Models: SP850-V2X2 2300 White Oak Circle urora, Il 60502 (800) 865-2112 Fax: (800) 359-6500 www.peerlessmounts.com ISSUED: 01-17-12 SHEET
More informationINSTALLATION INSTRUCTIONS FIXTURE SERIES: SAE 202 MOUNTING TYPE: RECESSED WALL / SLOT PAGE: 1 OF 8
INSTALLATION INSTRUCTIONS FIXTURE SERIES: SAE 202 MOUNTING TYPE: RECESSED WALL / SLOT PAGE: 1 OF 8 90v INNER CORNER KIT "R" (REGRESSED) POSITION CROSS-SECTION VIEW "S" (SHIELDING AT TOP) POSITION CROSS-SECTION
More informationHP 2 SERIES Integral Driver - Solid State LED
HP 2 SERIES Installation Instructions Warning High Voltage Hot Surface NEEDED FOR INSTALLATION: By Others 1/8 & 5/32 Allen Wrench Waterproof Wire Connectors Level Phillips Screwdriver IMPORTANT - WEAR
More informationInstallation Operation Care
Installation Operation Care Designer Roller and Designer Screen Shades Standard and Cassette Cordless Lifting System CONTENTS Getting Started: Product Views... 1 Tools and Fasteners Needed... 3 Installation
More informationINSTALLATION AND CARE INSTRUCTIONS
INSTALLATION AND CARE INSTRUCTIONS Skylight Manually Operated Honeycomb Shades 20 C8-10-1806 2/15 1 INTRODUCTION Thank you for purchasing our product. Your new shade has been custom built for you from
More informationHP-2 / HP-4 Wall Wash Recessed T-Bar Installation Instructions Overview
HP-2 / HP-4 Wash Recessed T-Bar Installation Instructions Overview NOTES All power connections should be installed according to local/national codes by a Certified Electrician. This installation requires
More informationOB1U INSTALLATION INSTRUCTIONS. Interactive Flat Panel Over White Board Mount
INSTALLATION INSTRUCTIONS Interactive Flat Panel Over White Board Mount Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description
More informationcompile system INSTALLATION GUIDE Updated January 2019
INSTALLATION GUIDE Updated January 09 compile system Table of Contents Panels 0 Quick Connect Clips 0 Lock Clips 0 Panel Trims 0 Privacy Glass 0 Post Base Covers 04 Electrical 04 Power Distribution Harness
More informationABM International, Inc. Navigator Assembly Manual
ABM International, Inc. 1 1.0: Parts List Tablet (Qty. 1) Tablet mount (Qty. 1) NOTE: Mount may appear and operate different then image below Control Box (Qty. 1) Motor Power Supply (Qty. 1) 2 X-axis motor
More informationUTILIBAY UTB2 HIGH BAY WARNINGS
UTILIBAY HIGH BAY WARNINGS WARNING: This product can expose you to chemical including lead and lead compounds, which are known to the State of California to cause cancer and birth defects or other reproduction
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationInstallation and Assembly: Ceiling mount for LCD screens up to 29"
Installation and Assembly: eiling mount for L screens up to 29" Models: L18-, L18-S, L36-, L36-S Features: omes in two adjustable height ranges (in 1" increments): 18"-30" and 36"-48" -5 to +20 adjustable
More informationC70 Window Roller Repair Taken from: Heres the problem:
C70 Window Roller Repair Taken from: http://www.volvospeed.com/vs_forum/topic/115086-how-to-c70-window-rollers-permanent-fix/ Heres the problem: This happened to two separate window assemblys on my c70
More informationInstallation and Assembly - Articulating Swivel Double-Arm for 42" - 71" Plasma Screens
Installation and ssembly - rticulating Swivel Double-rm for 42" - 71" Plasma Screens Models: PLV 70, PLV 70-S R This product is UL Listed. It must be installed by a qualified professional installer. Maximum
More informationMenu Board Tilt or Fixed Mount Installation Instructions MDS1T-200, MDS1T-300, MDS1T-400 MDS2T-200, MDS2T-300, MDS2T-400 MDS3T-200, MDS3T-300, MDS3T-400 MDS4T-200, MDS4T-300, MDS4T-400 MDS5T-200, MDS5T-300,
More informationMM340 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
MM30 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.
More information