FACTORY CAT TOMCAT CORPORATION

Size: px
Start display at page:

Download "FACTORY CAT TOMCAT CORPORATION"

Transcription

1 FACTORY CAT RPS TOMCAT CORPORATION Artificial Turf and Carpet Sweeping Install Kit # & # Detach batteries so that there is no power running through the machine before starting. 2. Start removing the side brooms by pulling the pins out of the side broom motors to drop the brooms off (SEE 1). Save these brooms off to the side, upside-down as to not bend the brushes. 3. Once the side brooms are removed you will have easier access to the four bolts that are holding the drive onto the drive plate. These need to be loosened (SEE 2-5). Using a 1/2 socket, loosen these bolts. Remove the positive and negative terminal wires from the drive. Note: You may need to spin the wheel around to access certain bolts better. 4. Now that the bolts are loosened, you will need to finish taking it off by lifting the front of the machine either by a hoist or a floor jack. Make sure to use a piece of wood or cardboard to not scratch up the paint on the frame from the lift point. 1 of 10

2 6. Once the screws of the parking brake casing are removed, the casing can easily come off (SEE 8-9). You don t need to take it off completely, just enough to get access to the four screws underneath the casing. These can be taken off with a 1/4 size socket (SEE 10-11). 5. Now that the drive is detached from the drive shaft, it s best to work on a table of some sort for the next steps (SEE 6). Turn the drive motor so that the parking brake is facing you, and remove the four screws that are holding the parking brake casing on (SEE 7). 2 of 10

3 7. Once the four screws are removed that are holding the parking brake on, the parking brake will come right off (SEE 12). Note: Make note of the position of the parking brake are at this time. During the reinstall you will need to know this. Normally it will (if you are facing it) be at around the 1 o clock position. 8. Now that you have removed the parking brake, you have access to a star knob which will need to be removed. To remove, use an 1.5 sized allen wrench to loosen (SEE 13). To loosen, two full turns usually is enough. 9. Once you have loosen the allen key, pop the star knob off (SEE 14). A screw driver or two is an easy solution. 10. With the star knob removed (save for re-install) you will have access now to the motor key (SEE 15). This is a very small crescent key. To remove, use a small flat head screw driver and a mallet and tap it lightly till it comes out and save to the side for re-install (SEE 16). 3 of 10

4 11. Now with the entire parking brake side removed, you are going to want to turn the drive around and locate the two main bolts holding the motor casing on (SEE 17). 12. Once you have located the bolts, remove them with a 7/16 socket (SEE 18). Pull them out and set them to the side. 13. With the bolts removed, grab hold of the back motor casing. In a quick motion, push the motor forward a tad and then quickly pull back. The magnets inside of the motor casing make it a little difficult for the casing to come off. To make it easier, have someone hold the wheel in place while the casing is being removed (SEE 19). Note: You want to make sure you make note of where the positive and negative terminal connections are facing before you fully remove the casing as to re-installing the new one has to match. 14. Now that the casing is removed, remove the motor by using a mallet and tapping the backside where the motor key was to pop the motor out. Sometimes this is harder than others and you may need a hoist to pull the motor out (SEE 20). 4 of 10

5 15. Now that the entire motor assembly has been removed off of the standard drive, the new motor needs to be reinstalled. Locate your motor # that was sent to you and preform steps on it so that you have the motor, the black cylindrical casing, as well as the back motor casing apart along with the two large bolts. 16. Now before we reassemble the upgraded motor into the regular drive, we have to reset all of the magnets in the back of the cylindrical casing (SEE 21). This should already be apart, if not using a mallet knock it out gently. Note: You may see a circular inner ring come loose or fall out. Keep this (SEE 25-26). 17. Each of the magnets need to be pushed back (SEE 22) and while being held back, a pin inserted into the hole on the top and the bottom of the magnet bracket (SEE 23). 18. Do this for all four of the magnets on the back casing (SEE 24). 5 of 10

6 19. Now that all the magnets are in place, you have room to place the ring mentioned in step 16 s Note (SEE 25). 20. When placing this ring back into the center of the back motor casing in between all of the magnet brackets, you must make sure that the rings ends are bent up (SEE 26-27). 21. Now that the ring is in place you can lightly set the motor into the motor case backing. You will feel this go into place. Give it a couple light taps with a mallet on the top of it to make sure it is snug in there (SEE 28). 22. All of the pins that are holding the magnets in place need to be removed now. Remove them gently and let the magnets snap into place. Easiest removal with another pin or needle nose pliers. 6 of 10

7 23. With all of the pins out of the magnet brackets and the motor fully in place on the back of the motor casing, you can now install the main black cylindrical casing. Before placing over motor, make sure to find the casing markings and line them up for the most part (SEE 29-30). Note: Before doing the next step make sure to wear gloves as the magnets inside the motor are very strong and you could pinch your hand. 25. Now that the motor is all assembled its time to load it into the wheel drive assembly. Before you load it in, mark with a black marker where the main motor bolt holes go on the outside rim of the wheel. This helps you locate the bolt holes later as when loading in the motor you can no longer see the holes (SEE 34). Note: Make sure your positive and negative terminals are the same as before. 24. With gloves on (SEE Note Above) slowly lower the casing over the motor. The magnets will grab on very fast. Slide the casing down over the motor (SEE 31) and make sure that the casing markings are lined up (SEE 32). If they aren t, turn the casing to re-align them. Once they are, tape the case in place (SEE 33). 7 of 10

8 26. Once the rim of the wheel is marked, place the motor into the drive assembly (SEE 35). You will feel it lock in and you will notice that the back of the motor will stick out of the other end of the assembly (SEE 36). 8 of With the motor all the way in place, now you can install the long bolts to attach the motor onto the drive assembly (SEE 37). In order to find these holes, use your black markings on the inner wheel rim. Once you get one slightly threaded, do the same for the other one. You want to tighten them both at about the same speed so that the motor sits level onto the drive assembly. 28. Once the motor is completely tightened, you can remove the tape that was holding the casing in place. Turn the motor around and re-install the crescent motor key into the back of the motor. Once that is in place, also reinstall the star knob on top of the key (SEE Steps 8-10). 29. Now with the key and star knob fastened in place, we can install the parking brake. Before installing, make sure that the inner ring as the ability to move around (SEE 38). 30. If the inner ring moves, skip this. Otherwise you need to disengage the parking brake by pulling one or the other way on the lever (SEE 39).

9 31. Refer back to Steps 6 and 7 on the rest of the parking break install. You might need to move the parking brake around a little bit for the star knob to fit inside of the star inner ring in the brake. Install the four bolts as well as the four screws for the parking brake cover and your motor has been successfully upgraded to a 2HP motor. 32. Install the drive back onto the machine the same way you took it off. Tighten the bolts on as much as you can before you lower the machine down onto the ground. You want to tighten them all at the same rate so that the drive sits square and flat on the drive plate. Reattach the positive and negative terminal connectors for the drive. 33. Lower the machine all the way onto the ground and now that there is weight on the tire, it won t move as much while you try to tighten it as much as possible. Your upgraded drive is now installed. 34. Remove your hopper and flip it over (SEE 40). We are going to be removing and installing a new seal on the bottom of the hopper. Using a 3/8 socket or wrench, remove all of the nuts and bolts and replace the curtain # with the #8-571L 1/32 Thick seal (SEE 41). If You Ordered # (Carpet Sweeping Package) All That Is Left To Do Is To Install The Broom #8-401NN And Reattach the batteries. You Do Not Need To Continue With This Guide. If You Ordered # (Artificial Turf Grooming Package) Continue On With This Install Guide. 9 of 10

10 35. Remove the Left Hand Side Door Curtain # (SEE 42). Remove the Inner Side Wiper # behind the Right Hand Side Door (SEE 43). Both can be removed with a 3/8 socket or wrench. 36. Find the Vertical Main Broom Curtain # (SEE 44-46; 45 is view from directly in back of the machine) and loosen all of the nuts. Normally this curtain is set as see in PICTURE 45, with the curtain being as low as it can go. We want to loosen the nuts and bolts and move it up all the way it can go and retighten all of the nuts and bolts. 37. All that is left to do is to replace the current broom with the Carpet Broom 8-401NN. Then reattach the batteries. 10 of 10

RPS. XR Front Drive Updates CORPORATION

RPS. XR Front Drive Updates CORPORATION FACTORY CAT 1. To start a replacement of the XR Front Wheel Drive, make sure the machine is on level ground with the rear wheels chocked and always disconnect the batteries. 2. Locate the Positive and

More information

Replacing the Reciprocator on the SWF Compact Series Machine (601C and 1201C)

Replacing the Reciprocator on the SWF Compact Series Machine (601C and 1201C) Follow the instructions below to replace the reciprocator in the SWF Compact series machines. The tools required can be found in the tool kit that came with the machine. Preparation 1. First, place the

More information

Replacing the Reciprocator on an SWF Multi-head.

Replacing the Reciprocator on an SWF Multi-head. Replacing the Reciprocator on an SWF Multi-head. Follow the instructions below to replace the reciprocator in the SWF multi-head machines. The tools required are found in the tool kit that came with the

More information

Bushwacker Jeep Flat Style Fender Flares Front Pair

Bushwacker Jeep Flat Style Fender Flares Front Pair Bushwacker Jeep Flat Style Fender Flares Front Pair Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Installation Time: 3-4 Hours Tools Required:

More information

INSTALLATION. Preparation:

INSTALLATION. Preparation: INSTALLATION Preparation: Average Time Required: 2 to 3 hours Place a blanket down in the area which you will be working in. This will prevent scratches on the rear fascia / valance. Remove your License

More information

Special Z-Axis Ballscrew Replacement

Special Z-Axis Ballscrew Replacement To replace Z-axis ballscrew without removing X-axis components When rebuilding an OmniTurn slide, all the precision components are replaced. The tooling plate and saddle are removed to gain access to the

More information

Rugged Ridge Engine Transmission Skid Plate JK

Rugged Ridge Engine Transmission Skid Plate JK Installation Time: 1-2 Hours Tools Required: Rugged Ridge Engine Transmission Skid Plate 2012-2017 JK Sockets: 16mm, 17mm, 18mm deep well Socket Wrench Wrenches: 16mm, 18mm Torque Wrench Drill ½ Drill

More information

MAG-CONV Basic, 48, 48R & Midline Front Mount

MAG-CONV Basic, 48, 48R & Midline Front Mount Parts Required: Tools Used: Mag Wheels Brakes Brake Rods Mounting Bracket Anti Tippers 7/16" Wrench Screw Driver Rubber Mallet 5/8 Wrench 5mm Allen Wrench Step Execution Figures 1 Remove front 5" total

More information

EmagiKit. Privacy Pod Plus. Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY

EmagiKit. Privacy Pod Plus. Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY EmagiKit Privacy Pod Plus Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY DIMENSIONS AND COMPONENTS 47 47 Ceiling Unit 2-B 2-L 2-R Glass Door Corner Trim Door Handle 90 Adjustable Height Work Surface 1-B

More information

Installation Guide for Rough Country 1.25 inch Body Lift Kit w/o Shocks (07-15 Wrangler JK 4 Door) Item # J10048 Option B; Manual

Installation Guide for Rough Country 1.25 inch Body Lift Kit w/o Shocks (07-15 Wrangler JK 4 Door) Item # J10048 Option B; Manual Installation Guide for Rough Country 1.25 inch Body Lift Kit w/o Shocks (07-15 Wrangler JK 4 Door) Item # J10048 Option B; Manual Installation Time: 3 Hours Tools Required: Jack (Tall enough to reach body

More information

400GTO Lubrication Guide

400GTO Lubrication Guide 400GTO Lubrication Guide Lubrication Guidelines for the following equatorial mounting: 400GTO Servo with GTOCP2 or CP3 Controller For other 400 models please review other postings as they become available.

More information

Step 1: The larger tower box contains the tower machine, a set of Silver 100 Lid Keys, and a set of Black 002 Coin Box Keys

Step 1: The larger tower box contains the tower machine, a set of Silver 100 Lid Keys, and a set of Black 002 Coin Box Keys 2 3 Step 1: Each tower is shipped as two boxes the large tower box and the smaller stand box. Open each of the boxes and inventory each of the parts before starting assembly to ensure all parts have arrived.

More information

Astro-Physics Inc. 400QMD Lubrication/Maintenance Guide

Astro-Physics Inc. 400QMD Lubrication/Maintenance Guide Astro-Physics Inc. 400QMD Lubrication/Maintenance Guide The following guidelines should be followed to lubricate the three main parts of the 400QMD mount. The QMD stands for Quartz Micro-Drive controller.

More information

AUDI A8 D3 REPLACING THE OUTSIDE DRIVER DOOR HANDLE

AUDI A8 D3 REPLACING THE OUTSIDE DRIVER DOOR HANDLE AUDI A8 D3 REPLACING THE OUTSIDE DRIVER DOOR HANDLE The keyless entry system in the D3 is a great feature. If you have the car key fob in your pocket, putting your hand under the door handle will unlock

More information

STEP 1 : DESTROYER FRONT BUMPER INSTALL GATHER YOUR TOOLS AND LAY OUT YOUR PARTS... *shorty bumper to show hardware* Tools Required:

STEP 1 : DESTROYER FRONT BUMPER INSTALL GATHER YOUR TOOLS AND LAY OUT YOUR PARTS... *shorty bumper to show hardware* Tools Required: DESTROYER FRONT BUMPER INSTALL JL STEP 1 : GATHER YOUR TOOLS AND LAY OUT YOUR PARTS... Tools Required: - Utility knife - 11/16 Deep socket - Ratchet - 11/16 Crescent wrench - Ratchet Extension - 1/4 socket

More information

How I fixed my HP Envy 15T-J100 Quad Broken Hinge

How I fixed my HP Envy 15T-J100 Quad Broken Hinge How I fixed my HP Envy 15T-J100 Quad Broken Hinge My daughter sent me the picture below from college (she s in school in AZ, about 1500 miles from home) she lifted the screen on her PC and the base cover

More information

THIS KIT INCLUDES: 8 M8-1.25X40MM BOLTS WITH WASHERS 8 M8-1.25X30MM BOLTS WITH WASHERS RIGHT AND LEFT HINGE

THIS KIT INCLUDES: 8 M8-1.25X40MM BOLTS WITH WASHERS 8 M8-1.25X30MM BOLTS WITH WASHERS RIGHT AND LEFT HINGE Sal es@lambodoorscanada. com 2407A Kal adarave,ottawa,on K1V 8B9 THIS KIT INCLUDES: 8 M8-1.25X40MM BOLTS WITH WASHERS 8 M8-1.25X30MM BOLTS WITH WASHERS RIGHT AND LEFT HINGE 2 SHOCKS 565 PSI 2 SHOULDER

More information

CORVETTE CORVETTE REV: Made in USA U.S. PATENT #6,808,223; #6,845,547; #7,140,075; #7,059,655 and other patents pending.

CORVETTE CORVETTE REV: Made in USA U.S. PATENT #6,808,223; #6,845,547; #7,140,075; #7,059,655 and other patents pending. CORVETTE 2005-2006 CORVETTE 2005-2007 REV: 7-2-07 Made in USA U.S. PATENT #6,808,223; #6,845,547; #7,140,075; #7,059,655 and other patents pending. Page 1 of 12 CORVETTE C6 2005-2007 THIS KIT INCLUDES:

More information

Replacement of Drive Nuts in TTL/Adding Drive Nut Safety Bracket

Replacement of Drive Nuts in TTL/Adding Drive Nut Safety Bracket Replacement of Drive Nuts in TTL/Adding Drive Nut Safety Bracket The bronze drive nuts in the TrusLift are the main lifting components, working in conjunction with the drive screw, gear reducer and

More information

For additional assistance call

For additional assistance call The following pages will help guide you through the process of assembling your new 48 custom prize wheel. Choose an assembly area with plenty of room to lay your pieces on the floor and also a bench or

More information

KWM Gutterman Inc. 5 /6 IRONMAN COMBO CONVERSION

KWM Gutterman Inc. 5 /6 IRONMAN COMBO CONVERSION 5 /6 IRONMAN COMBO CONVERSION SECTION: 2 6 To 5 Conversion This section will direct you in converting your combo machine from a 6 to 5 machine. BEFORE BEGINNING CHANGEOVER Eliminate electrical power source

More information

INSTALLING YOUR NEW SPRING LIFT ARM KIT

INSTALLING YOUR NEW SPRING LIFT ARM KIT INSTALLING YOUR NEW SPRING LIFT ARM KIT 1. Measure the distance that the roof is to be raised. [If your lift system is completely non-functional, you will need to calculate or estimate this distance as

More information

EPPA2-KIT DUAL MONITOR ARM CONVERSION

EPPA2-KIT DUAL MONITOR ARM CONVERSION EPPA2-KIT DUAL MONITOR ARM CONVERSION EPPA2-KIT Rev A 10/17 Model EPPA2-KIT-XXX ASSEMBLY AND ADJUSTMENT EPPA2-KIT PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and adjustment

More information

INSTALLATION INSTRUCTIONS: ULTRA FRONT FENDER FLARES

INSTALLATION INSTRUCTIONS: ULTRA FRONT FENDER FLARES INSTALLATION INSTRUCTIONS: ULTRA FRONT FENDER FLARES Thank you for your purchase of Crawler Conceptz Ultra Series Front Fender Flares. While these flares are easily installed with basic hand tools and

More information

ASSEMBLING YOUR L&L EASY-FIRE KILN

ASSEMBLING YOUR L&L EASY-FIRE KILN TABLE OF CONTENTS TOOLS NEED FOR THE JOB............ 1 UNPACKING........................... 2 Inspect for visible damage.......................... 2 Remove Top from Carton........................... 2

More information

Ford F150 Front Bumper

Ford F150 Front Bumper 2009-2011 Ford F150 Front Bumper Warning! Read the instructions completely before beginning the installation. Before tightening bolts, drilling or cutting where required, check to make sure that there

More information

7878 K940. Checkpoint Antenna. Kit Instructions. Issue B

7878 K940. Checkpoint Antenna. Kit Instructions. Issue B 7878 K940 Checkpoint Antenna Kit Instructions Issue B Revision Record Issue Date Remarks A July 7, 2009 First issue B Nov2013 Revised the Checkpoint installation procedures for 7878 and 7874 scanners Added

More information

INSTALLATION INSTRUCTIONS DODGE RAM 2 & 4WD 1500 PART # P5058

INSTALLATION INSTRUCTIONS DODGE RAM 2 & 4WD 1500 PART # P5058 INSTALLATION INSTRUCTIONS 2009-13 DODGE RAM 2 & 4WD 1500 PART # P5058 PARTS LIST: Qty Description Qty Description 1 Grille Guard 12 12-1.75mm Hex Nuts 2 Upper Frame Mounting s (for trucks without tow hooks

More information

OPERATIONS MANUAL. Port-O-Slitter

OPERATIONS MANUAL. Port-O-Slitter Tapco Products Company The World Leader in Specialty Tools for the Professional Port-O-Slitter OPERATIONS MANUAL General instructions, set up, accessories and guide to using your portable precision slitting,

More information

Bushwacker Jeep Flat Style Fender Flares Rear Pair (JK Wrangler 2dr)

Bushwacker Jeep Flat Style Fender Flares Rear Pair (JK Wrangler 2dr) Bushwacker Jeep Flat Style Fender Flares Rear Pair (JK Wrangler 2dr) Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Installation Time: 3-4

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS PLATINUM 4 OVAL STEP BAR (90 BENT END) APPLICATION: 2010-2015 Dodge Ram 2500/3500 Mega Cab PART NUMBER: 21-3570, 21-3575, 23-3570, 23-3575, 25-3570, 25-3575,

More information

Hardware and Components:

Hardware and Components: Hardware and Components: (A) 4X 5/16 x 1 Carriage Bolt (B) 2X 5/16 x 2-1/4 Carriage Bolt (C) 2X 5/16 x 3-1/4 Hex Bolt (D) 2X 5/16 x 3/4 Hex Bolt (E) 2X 5/16 x 1-1/4 Hex Bolt (F) 5/16 x 2-1/4 Hex Bolt (G)

More information

RBP-1215B-RX DODGE RAM QUAD CAB RX3

RBP-1215B-RX DODGE RAM QUAD CAB RX3 RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side

More information

The Phoenix. Professional Quilting Frame. Copyright January 1, 2016 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2.

The Phoenix. Professional Quilting Frame. Copyright January 1, 2016 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2. The Phoenix Professional Quilting Frame Copyright January 1, 2016 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2.1 1 The Phoenix Professional Quilting Frame Parts List Box 1...3 Box

More information

INSTALLATION INSTRUCTIONS GRILLE GUARD RAM 1500 PART # 5058/5058-2

INSTALLATION INSTRUCTIONS GRILLE GUARD RAM 1500 PART # 5058/5058-2 INSTALLATION INSTRUCTIONS GRILLE GUARD PART # 5058/5058-2 PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Upper Frame Mounting s (for trucks without tow hooks

More information

SAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.

SAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER. SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions

More information

Applications: Section 1: Getting Started Tools Needed: BEFORE

Applications: Section 1: Getting Started Tools Needed: BEFORE Installation of KBD Body Kits Porsche GT 3 Look/Style 2 Piece Polyurethane Front Bumper & Lip Applications: Porsche 996: 1999-2001 Porsche Boxster 986: 1997-2004 Page 1 Tools Needed: Philips Head Screwdriver

More information

CAB END BEDTRAX (SIDE VIEW)

CAB END BEDTRAX (SIDE VIEW) Supplied Hardware: (8-14) 1/4-20 Allen head bolts, (12-18) UHMW mount blocks, (4) D-ring tie downs Tools Needed: Allen head wrench GET TO IT. INSTALLATION INSTRUCTIONS STEP 1. INSERT (2) MOUNT BLOCKS INTO

More information

BY ALIEN TECHNOLOGIES CORP

BY ALIEN TECHNOLOGIES CORP BY ALIEN TECHNOLOGIES CORP Assembly Instructions TopLift Pros YOU MAY ALSO REVIEW OUR ASSEMBLY VIDEO, PLAY AND PAUSE AT YOUR CONVENIENCE. JUST VISIT US AT WWW.TOPLIFTPROS.COM AND GO TO Customer Support

More information

Referencing 0,0 position

Referencing 0,0 position Page 1 of 11 TITLE: SABRE X-Axis Lead Screw Replacement Procedure Gerber FastFact #: 2013 Supplied by: Gerber Hardware Support Last Modified: March 1, 2011 Summary: The following procedure explains how

More information

C70 Window Roller Repair Taken from: Heres the problem:

C70 Window Roller Repair Taken from:  Heres the problem: C70 Window Roller Repair Taken from: http://www.volvospeed.com/vs_forum/topic/115086-how-to-c70-window-rollers-permanent-fix/ Heres the problem: This happened to two separate window assemblys on my c70

More information

Installation Instructions for Vista Air Vertically Folding Walls

Installation Instructions for Vista Air Vertically Folding Walls Installation Instructions for Vista Air Vertically Folding Walls Use these instructions in conjunction with your shop drawings to see the specifics that are particular to the model you are installing.

More information

Roomba 500 Series Servicing and Repair Guide. Chapter 3: How to Open Up Roomba

Roomba 500 Series Servicing and Repair Guide. Chapter 3: How to Open Up Roomba Roomba 500 Series Servicing and Repair Guide Chapter 3: How to Open Up Roomba 1 This repair guide explains how to perform general disassembly on the Roomba 500 series robot vacuum. It is suggested to consult

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS TEL:1-866-XANATOS INSTALLATION INSTRUCTIONS FOR 07-13 CHEVY SILVERADO 1500 PART#RU-CHSI07-B PARTS LIST: 1 Main Body 28 12mm x 37mm OD x 3mm Large Flat Washers 1 Driver/Left Brush Guard 8 12-1.75mm x 40mm

More information

Trus<T>Lift Replacement of Screw and Gearbox in Tower (28, 52, 72)

Trus<T>Lift Replacement of Screw and Gearbox in Tower (28, 52, 72) TrusLift Replacement of Screw and Gearbox in Tower (28, 52, 72) The following procedure walks through the changing out of a gearbox and screw in a TTL Tower. Tools Required Socket Wrench 3/8 Drive Tape

More information

INSTALLATION GUIDE NS Double Clamp Ladder Rack NV200 / City Express ( Aluminum )

INSTALLATION GUIDE NS Double Clamp Ladder Rack NV200 / City Express ( Aluminum ) INSTALLATION GUIDE 1530-NS Double Clamp Ladder Rack NV200 / City Express ( Aluminum ) QUICK START GUIDE Phase 1 - Assembly q 1.1 Setup... q 1.2 Ladder Rack Assembly... 3-5 5-13 Phase 2 - Installation q

More information

TRUE TECHNICAL SERVICE MANUAL - ALL MODELS. DOORS/DRAWERS/LIDS

TRUE TECHNICAL SERVICE MANUAL - ALL MODELS.  DOORS/DRAWERS/LIDS DOORS/DRAWERS/LIDS 55 56 NOTES DOORS/DRAWERS/LIDS Springs 97 TORSION SPRING REPLACEMENT GDM RADIUS FRONT - SWING DOOR INSTALLATION INSTRUCTIONS Tools Required (2) - 1 8" drift Punch (forged) Needle-Nose

More information

Fortress Fe Posts must always be secured to the deck framing. Fortress Fe Posts should never be attached to only the deck boards.

Fortress Fe Posts must always be secured to the deck framing. Fortress Fe Posts should never be attached to only the deck boards. Installation Instructions for Fortress Horizontal Cable Panel System with UB-05 Brackets and Fe Posts It is the responsibility of the installer to meet all code and safety requirements, and to obtain all

More information

JK Brawler Rockers. *Includes ONE of the Hardware Kits (not both)

JK Brawler Rockers. *Includes ONE of the Hardware Kits (not both) INSTALLATION INSTRUCTIONS INST-17-08-200_A JK Brawler Rockers IMPORTANT: Thank you for purchasing this Poison Spyder product. Please read through this entire document before proceeding with installation.

More information

MS2 Straight Key Kit Assembly Manual

MS2 Straight Key Kit Assembly Manual American Morse Equipment MS2 Straight Key Kit Assembly Manual Thank you for purchasing our MS2 Miniature Straight Key Kit! Please take a few minutes to look over these instructions before starting assembly.

More information

Volvo 240/260 New Face Overlay Installation Models By Dave Barton

Volvo 240/260 New Face Overlay Installation Models By Dave Barton Volvo 240/260 New Face Overlay Installation 1975-80 Models By Dave Barton These custom faces are the product of years of research and experimentation. They are printed with a special printer using waterproof

More information

INSTALLATION MANUAL FRONT. See pages 2 and 3 of this manual for configuration options. Level of Difficulty. Product Photo (center section only)

INSTALLATION MANUAL FRONT. See pages 2 and 3 of this manual for configuration options. Level of Difficulty. Product Photo (center section only) INSTALLATION MANUAL FRONT Level of Difficulty Moderate Product Photo (center section only) All hardware listed below will be provided with the bumpers center section. Additional hardware will be supplied

More information

Metroboard Pulley Replacement Procedure

Metroboard Pulley Replacement Procedure Metroboard Pulley Replacement Procedure 1) Remove the two transmission cover screws (1/8 allen driver). Then remove the transmission cover. Note there is a split lock washer and flat washer as well, so

More information

TOOLS REQUIRED FOR INSTALLATION: AIR RACHET, GRINDER AND CUTTER.

TOOLS REQUIRED FOR INSTALLATION: AIR RACHET, GRINDER AND CUTTER. THIS KIT INCLUDES: 16 M8-1.25X30MM BOLTS WITH WASHERS 2 SHOCKS 565 PSI RIGHT AND LEFT HINGE ASSEMBLY 2 SHOULDER BOLTS 2 PINS TOOLS REQUIRED FOR INSTALLATION: AIR RACHET, GRINDER AND CUTTER. 7/23, 10MM,

More information

OTECO INC. MODEL ,000 PSI 4-1/16 PORT DM GATE VALVE MAINTENANCE MANUAL

OTECO INC. MODEL ,000 PSI 4-1/16 PORT DM GATE VALVE MAINTENANCE MANUAL Page 1 of 7 OTECO INC. MODEL 45 4 5,000 PSI 4-1/16 PORT DM GATE VALVE MAINTENANCE MANUAL Page 2 of 7 TABLE OF CONTENTS 1. Assembly Blowout 2. Repair Kit Contents & Technical Specifications 3. Disassembly

More information

VIEWPOINT ALUMINUM RUNNING BOARD TOYOTA RAV4

VIEWPOINT ALUMINUM RUNNING BOARD TOYOTA RAV4 PARTS LIST: VIEWPOINT ALUMINUM RUNNING BOARD 1 Driver/Left Running Board 4 10-1.5mm x 50mm T-Bolt 1 Passenger/Right Running Board 12 10mm Plastic Retainers 1 Driver/Left Bracket 2 10-1.50mm x 40mm Hex

More information

Removing and Replacing the Y-truck

Removing and Replacing the Y-truck Service Documentation Removing and Replacing the Y-truck To remove and replace the Y-truck you will need the following tools: 4mm Allen wrench 12mm stamped flat wrench #2 Phillips screwdriver (magnetic

More information

ACCESS COVER INSTALLATION INSTRUCTIONS (Kit #601 for 2006 Honda Ridgeline)

ACCESS COVER INSTALLATION INSTRUCTIONS (Kit #601 for 2006 Honda Ridgeline) ACCESS COVER INSTALLATION INSTRUCTIONS (Kit #601 for 2006 Honda Ridgeline) NOTE TO INSTALLER: IMPORTANT READ BEFORE ATTEMPTING INSTALLATION. Allow extra time, up to 2 hours to install this cover. Disassembly

More information

TIRE RACK INSTALLATION INSTRUCTIONS Dodge Sprinter

TIRE RACK INSTALLATION INSTRUCTIONS Dodge Sprinter Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 TIRE RACK INSTALLATION INSTRUCTIONS 07-11 Dodge Sprinter Please read before beginning Stainless steel hardware may bind together

More information

IMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE

IMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE IMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE 005-07 Cadillac STS Classic 3D Z, Classic Dual Weave, Classic Mesh & Classic Black Mesh Grilles B 7 HR 3 STS Classic 3D Z Grille Part

More information

HQ Precision-Glide Track Upgrade 2 Extension Kit for HQ Studio Frame Part# QF09750

HQ Precision-Glide Track Upgrade 2 Extension Kit for HQ Studio Frame Part# QF09750 HQ Precision-Glide Track Upgrade 2 Extension Kit for HQ Studio Frame Part# QF09750 Important Note: Upgrading the track system on the HQ Studio Frame requires the use of this 2 Extension Kit (Part #QF09750),

More information

ES# ECS MKV R32 Dead Pedal Kit Installation Instructions

ES# ECS MKV R32 Dead Pedal Kit Installation Instructions ECS MKV R32 Dead Pedal Kit ES#261054 Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety of those performing the repairs.

More information

Rugged Ridge 2 Receiver Hitch Kit (J21068)

Rugged Ridge 2 Receiver Hitch Kit (J21068) Rugged Ridge 2 Receiver Hitch Kit (J21068) Installation Time: 1-2 Hours Tools Required: ¾ Open End Wrench 18 mm Socket ¼ drive Pliers/Needle nose pliers/channel locks, etc. Torque wrench Phillips head

More information

MMD Convertible Styling Bar Customer Installation Guide

MMD Convertible Styling Bar Customer Installation Guide MMD Convertible Styling Bar Customer Installation Guide TOOLS REQUIRED/RECOMMENDED: Electric Drill 1 Forstner Bit (Hole Saw) 1 3/8 Hole Saw (manual calls for 1 ¾ ) 1/8, 3/8 & ¾ Drill Bits Rivet Gun Trim

More information

Technical Procedure. HIITMill (X) Push/Pull Brake Cable Install

Technical Procedure. HIITMill (X) Push/Pull Brake Cable Install HIITMill (X) Push/Pull Brake Cable Install Applies to: HIITMill and HIITMill X Required Tools: 2.5mm Allen Key 3mm Allen Key 4mm Allen Key 5mm Allen Key 6mm Allen Key 10mm Wrench 10mm Socket Ratchet Needle

More information

Castle Frame Assembly Table AT-8. Diagnostics Manual. Castle, Inc. Petaluma, CA

Castle Frame Assembly Table AT-8. Diagnostics Manual. Castle, Inc. Petaluma, CA Castle Frame Assembly Table AT-8 Diagnostics Manual Castle, Inc. Petaluma, CA 800-282-8338 Solutions Index Adjusting the Tabletop.. 8.01 Adjusting the Fence... 8.02 Aligning the Arm... 8.10 Adjusting Bracket..

More information

Race Splitter Upgrade Kit Installation Instructions

Race Splitter Upgrade Kit Installation Instructions Race Splitter Upgrade Kit Installation Instructions Eric Hazen Rev. 1 Overview: Detailed instructions on installing the FT86 Speed Factory Race Splitter Upgrade Kit on a BRZ; FR-S grills are different

More information

BOLT ON LONG TRAVEL FOR E-Z-GO

BOLT ON LONG TRAVEL FOR E-Z-GO INSTALLATION INSTRUCTIONS BOLT ON LONG TRAVEL FOR E-Z-GO 1994 2000 Model E-7-04 E-7-06 TABLE OF CONTENTS Progressive Supension Kit... 2 Kit Contents...3-4 Disassembly...5-10 Frame Assembly...11-14 Frame

More information

RTI TECHNOLOGIES, INC.

RTI TECHNOLOGIES, INC. RTI TECHNOLOGIES, INC. BRC500 & BRC550 Arbor/Spindle Mechanism Adjustment & Service Technical Instructions The arbor/spindle mechanism of the BRC500/550 is designed to be robust for long life. Occasionally

More information

TRAILMATE METEOR ASSEMBLY MANUAL

TRAILMATE METEOR ASSEMBLY MANUAL TRAILMATE METEOR ASSEMBLY MANUAL The Trailmate Meteor recumbent has been designed for easy assembly. This means more time to enjoy the smooth ride with single speed, 3 speed coaster brake and 21 speed

More information

Rugged Ridge Body Armor Guard Kit, 5 Pieces, Black (07-Current JK 4-door)

Rugged Ridge Body Armor Guard Kit, 5 Pieces, Black (07-Current JK 4-door) Rugged Ridge Body Armor Guard Kit, 5 Pieces, Black (07-Current JK 4-door) Installation Time: 60 Minutes Tools Required: Notes: Phillips head screwdriver 3/8 socket or Flat head screwdriver 1/2 socket 7

More information

Heavy Duty Ceiling Tilt Mount Installation Manual

Heavy Duty Ceiling Tilt Mount Installation Manual HD-CTM-5580 Heavy Duty Ceiling Tilt Mount Installation Manual *This Installation requires a minimum of two people. For your safety: Read the complete instruction manual before starting an installation

More information

OPERATION MANUAL MODEL

OPERATION MANUAL MODEL OPERATION MANUAL MODEL 60-511504 SUPPLIER CODE: GO-60-511504 BREEZER MESH OFFICE TASK CHAIR - GRAY/BLACK CUSTOMER SERVICE For fastest service, please visit our website at www.comfortproducts.net/support

More information

High Rise Sit-Stand Desk Converter

High Rise Sit-Stand Desk Converter High Rise Sit-Stand Desk Converter Assembly Instructions for Model DC300 Patent Pending PRE-ASSEMBLY Please read all instructions before beginning assembly. We strongly recommend you watch the video at

More information

MODULAR BUMPER INSTALLATION MANUAL

MODULAR BUMPER INSTALLATION MANUAL MODULAR BUMPER INSTALLATION MANUAL Parts List* 1 Center section 1 Side extension, passenger / right 1 Side extension, driver / left 1 Side cap, passenger / right 1 Side cap, driver / left 1 Brush guard,

More information

CTTR Tire Rack Required tools

CTTR Tire Rack Required tools CTTR Tire Rack Required tools Torque wrench, ratchet, 9/16 socket, tape measure, and square edge. ASSEMBLY REQUIREMENTS *Torque all T-bolt nuts to 35-40 foot pounds. Failure to follow the assembly instructions

More information

RUMFORD 1000 / 1000CD / 1000H

RUMFORD 1000 / 1000CD / 1000H RUMFORD 1000 / 1000CD / 1000H TABLE OF CONTENTS Dear Customer, The Renaissance Rumford 1000, 1000CD, 1000H are all members of the Renaissance Fireplaces TM family of ultra high end, low emission fireplaces.

More information

Exponents Bench Cushion

Exponents Bench Cushion Exponents Bench Cushion Power Drill #2 Phillips Bit Bit Holder Page 1 of 2 939500640 Rev A 1. Place cushion on top of the bench, so the black Coalesse tag is in the right rear corner of the bench. 2. From

More information

TABLE OF CONTENTS REQUIRED TOOLS

TABLE OF CONTENTS REQUIRED TOOLS TABLE OF CONTENTS SECTION SECTION TITLE PAGE NO. 1 2 3 4 5 Assembling Mounting Structure Installing Bicycle Supports Mounting Rack to Wall Adding Sections Customizing Rack Configuration REQUIRED TOOLS

More information

CORVETTE Page 1 of 12 CORVETTE C

CORVETTE Page 1 of 12 CORVETTE C CORVETTE 2005-2006 Page 1 of 12 CORVETTE C5 1997-2004 THIS KIT INCLUDES: 8 M8-1.25X40MM BOLTS WITH WASHERS 8 M8-1.25X30MM BOLTS WITH WASHERS RIGHT AND LEFT HINGE ASSEMBLY WIRE LOOM 2 SHOCKS 565 PSI 2 SHOULDER

More information

RH-412 STEEL DOORS INSTALLATION INSTRUCTIONS

RH-412 STEEL DOORS INSTALLATION INSTRUCTIONS RH-412 STEEL DOORS INSTALLATION INSTRUCTIONS By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side.

More information

REPAIR INSTRUCTIONS. Cat. No Cat. No MILWAUKEE ELECTRIC TOOL CORPORATION. SDS Max Demolition Hammer. SDS Max Rotary Hammer

REPAIR INSTRUCTIONS. Cat. No Cat. No MILWAUKEE ELECTRIC TOOL CORPORATION. SDS Max Demolition Hammer. SDS Max Rotary Hammer Cat. No. 9-0 SDS Max Demolition Hammer Cat. No. -0 SDS Max Rotary Hammer MILWAUKEE ELECTRIC TOOL CORPORATION W. LISBON ROAD BROOKFIELD, WISCONSIN 00-0 8-9-0 d 000 8-9-0 d Special Tools Require Forcing

More information

Assembly Instructions

Assembly Instructions Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt

More information

Y Cap Topper Tracks, 49 Cross Bars. Y Cap Topper Tracks, 54 Cross Bars. Y Cap Topper Tracks, 59 Cross Bars.

Y Cap Topper Tracks, 49 Cross Bars. Y Cap Topper Tracks, 54 Cross Bars. Y Cap Topper Tracks, 59 Cross Bars. Y02-470 - 63 Cap Topper Tracks, 49 Cross Bars. Y02-480 - 63 Cap Topper Tracks, 54 Cross Bars. Y02-490 - 63 Cap Topper Tracks, 59 Cross Bars. Important: Parts List Please read these instructions carefully

More information

PROVEN WORLDWIDE SNORKEL FOR CHEVY COLORADO NEW PRODUCT

PROVEN WORLDWIDE SNORKEL FOR CHEVY COLORADO NEW PRODUCT AEV30272AC Last Updated: 10/09/18 PROVEN WORLDWIDE SNORKEL FOR CHEVY COLORADO NEW PRODUCT Please visit www.aev-conversions.com to view the most current installation guide for this product. This is a new

More information

Fortress Fe Posts must always be secured to the deck framing. Fortress Fe Posts should never be attached to only the deck boards.

Fortress Fe Posts must always be secured to the deck framing. Fortress Fe Posts should never be attached to only the deck boards. Installation Instructions for FortressCable H-Series Cable Panel System With UB-05 Brackets and Fe Posts It is the responsibility of the installer to meet all code and safety requirements, and to obtain

More information

N. 15th Street, Middlesboro, KY FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS

N. 15th Street, Middlesboro, KY FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS 1-800-248-7717 1002 N. 15th Street, Middlesboro, KY 40965 FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Mountain Flip Tarp Dump Body tarping system. With tarping systems

More information

2 SHOULDER BOLTS RIGHT AND LEFT HINGE USE 4 EXISITING DOOR BOLTS TOOLS REQUIRED FOR INSTALLATION: AIR RACHET, GRINDER AND CUTTER.

2 SHOULDER BOLTS RIGHT AND LEFT HINGE USE 4 EXISITING DOOR BOLTS TOOLS REQUIRED FOR INSTALLATION: AIR RACHET, GRINDER AND CUTTER. Page 1 of 12 NISSAN 350Z 2003-2004 THIS KIT INCLUDES: 8 BOLTS WITH WASHERS 2 SHOCKS 780 PSI 2 PINS 2 SHOULDER BOLTS RIGHT AND LEFT HINGE USE 4 EXISITING DOOR ASSEMBLY BOLTS TOOLS REQUIRED FOR INSTALLATION:

More information

Tools Required: - Utility knife - 11/16 Deep socket - Ratchet - 11/16 Crescent wrench - Ratchet Extension - 1/4 socket - Electrical tape

Tools Required: - Utility knife - 11/16 Deep socket - Ratchet - 11/16 Crescent wrench - Ratchet Extension - 1/4 socket - Electrical tape DESTROYER FRONT BUMPER INSTALL JL STEP 1 : GATHER YOUR TOOLS AND LAY OUT YOUR PARTS... Tools Required: - Utility knife - 11/16 Deep socket - Ratchet - 11/16 Crescent wrench - Ratchet Extension - 1/4 socket

More information

REMOVAL/INSTALL INSTRUCTIONS: REPLACEMENT RADIO BUTTONS

REMOVAL/INSTALL INSTRUCTIONS: REPLACEMENT RADIO BUTTONS REMOVAL/INSTALL OF RADIO BUTTONS (Part# 76822) GM Vehicles 2003-2007 General Tech Tips: Work in a location that is clean & static-free (static discharge has the potential to permanently damage electrical

More information

Hollywood Swing Away 2 and 4 Bike Racks Assembly and Installation Guide

Hollywood Swing Away 2 and 4 Bike Racks Assembly and Installation Guide Hollywood Swing Away 2 and 4 Bike Racks Assembly and Installation Guide Tools Required: two adjustable wrenches, pliers, ¾ socket wrench recommended Note: please do assembly near your vehicle as you Can

More information

Thor Audi A4/S4 Skid Plate Installation Instructions

Thor Audi A4/S4 Skid Plate Installation Instructions Thor Audi A4/S4 Skid Plate Installation Instructions Parts List: 1 Aluminum Skid Plate 2 Aluminum Side Wings 10 10mm Flat Washers 3 8mm Flat Washers 3 8mm Speed Clips 2 10x40mm Bolts 3 8x35mm Bolts 2 Rivet-nuts

More information

C4 Fabrication Rock Slider Installation 14+ 5th Gen 4Runner w/o KDSS

C4 Fabrication Rock Slider Installation 14+ 5th Gen 4Runner w/o KDSS C4 Fabrication Rock Slider Installation 14+ 5th Gen 4Runner w/o KDSS Thank you for your purchase of the C4 Fabrication s 5th Gen 4Runner Rock Sliders! This product was carefully crafted to ensure a perfect

More information

INSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART #

INSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART # INSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART # PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Brackets (for trucks without 22 12mm x 30.1mm OD

More information

INSTALLATION INSTRUCTIONS RH 412 STEEL DOORS

INSTALLATION INSTRUCTIONS RH 412 STEEL DOORS By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side. Note: Having the hood open makes the job

More information

ASSEMBLY INSTRUCTIONS FOR L&L DURA-FIRE KILNS

ASSEMBLY INSTRUCTIONS FOR L&L DURA-FIRE KILNS TABLE OF CONTENTS TOOLS NEED FOR THE JOB................. 1 UNPACKING............................... 2 Inspect for visible damage............................ 2 Contents of the shipment............................

More information

PEARL DRUM PEDAL. Instruction Manual

PEARL DRUM PEDAL. Instruction Manual PEARL DRUM PEDAL Instruction Manual Congratulations on your purchase! To get optimum performance of your "P-3002D" Drum Pedal, please read this Instruction Manual before playing. Drive Shaft Assembly Drive

More information

TOOL LIST FOR TAILGATE HIDDEN LATCH & LINK ASSY FOR FORD FLARESIDE TRUCKS

TOOL LIST FOR TAILGATE HIDDEN LATCH & LINK ASSY FOR FORD FLARESIDE TRUCKS TOOL LIST FOR TAILGATE HIDDEN LATCH & LINK ASSY FOR 53-87 FORD FLARESIDE TRUCKS Vise Grip Clamps C-clamps Sharpie Marker Ball Peen Hammer Center Punch 3/8 or 1/2 Drill 5/32, 7/32, 9/32, and 3/8 Drill Bits

More information

OPERATIONAL MANUAL V1.0. Removing/Replacing Blades

OPERATIONAL MANUAL V1.0. Removing/Replacing Blades OPERATIONAL MANUAL V1.0 BLUEROCK WS-212 Wire Stripper Removing/Replacing Blades CAUTION!! IMPORTANT!! DANGER!! WARNING!! DISCONNECT MACHINE FROM POWER BEFORE PROCEEDING!! Estimated Completion Time: 90

More information

Signal Mirror Installation Instructions

Signal Mirror Installation Instructions Signal Mirror Installation Instructions 2005-2010 Chevy Corvette C6 THE safety accessory of the 21 st Century. P/N 210-0144-0 Rev. A3 (9/29/2011), BTV 2007 Muth Mirror Systems, LLC Page 3 of 10PplPage

More information