NH3 system. This procedure should only be used as a guide; your particular installation may be different depending on the NH3 controlling system.
|
|
- Hillary Webb
- 5 years ago
- Views:
Transcription
1 NOTE!: This installation procedure is for an Ag Leader temperature sensor on a Raven AccuFlow Vortex NH3 system. This procedure should only be used as a guide; your particular installation may be different depending on the NH3 controlling system. SAFETY WARNING!: Before beginning this installation, the anhydrous control system will need to be bled of all excess anhydrous pressure. Refer to the system s operators manual for further instructions. 1. Locate the current analog temperature gauge. It is typically found near the cooler and flow meter (Refer to Figure 1). Flow Meter Figure 1 2. Remove the current temperature gauge, OR locate a secondary location to install temperature sensor. (Having both the digital sensor and analog sensor on the system will aid in the sensor calibration, but is not required.) If the temperature calibration will be done immediately after the sensor is installed, note the current temperature on the guage before removal; this value will be needed later on during the calibration process. *** (Figure 2 indicates where the temperature gauge may also be located)
2 Temperature Sensor Figure 2 3. Install the Ag Leader temperature sensor (PN: Figure 3) and appropriate fittings (Figure 4). The Ag Leader temperature sensor kit does not come with pipe fittings, they will need to be sourced by the installer. Use pipe sealent when installing components. Sensor is installed in Figure 5. Figure 3 Figure 4
3 Figure 5 4. Connect the extension cable (PN: x) to the sensor and route it to the ISO Liquid Control Module. Locate the Channel cable, and then plug in the corresponding end of the extension cable into the P3 connection. The connections labeled P# are designated for pressure sensor inputs, and P3 is designated for temperature sensing when Anhydrous Ammonia is setup as the ISO Liquid System.
4 Sensor Calibration and Usage When a temperature and main line pressure sensor are installed, the ISO Liquid Module has the capability to perform vapor state monitoring. Both pressure and temperature sensors will need to be calibrated. The temperature sensor calibration is outlined below. 1. Press the Gear icon on the UT screen, and then press the Temperature Sensor button. 2. Define whether the sensor is a Voltage or Current Loop type by pressing the Wrench icon in Figure 6 (Ag Leader s sensor is a Current Loop type). Figure 6 3. Enter the mv/f calibration value of the sensor. If the calibration number of the sensor is unknown, press the Derive Sensor Calibration button. (With the Ag Leader sensor it is advised to use the Derive Sensor Cal procedure) a. Sensor Characteristics for Ag Leader sensor (also located on the sensor body): i. Min Temp = -58 F (-50 C) ii. Max Temp = 302 F (150 C) iii. Min ma = 4 iv. Max ma = Once the values are entered, press the Calculate button (Figure 7). The derived calibration number is now present. Press the forward arrow. 5. Enter the current temperature in degrees Fahrenheit, and then press the Record Set Point. Press the forward arrow. 6. The Calibration is now complete. Press the green check mark to save the new calibration value. Figure 7
5 Once both the pressure sensor and temperature sensors are calibrated, the Map screen and UT pressure gauges now display a RED and GREEN portion on the gauge. These colors are the NH3 state indicators. Universal Terminal Gauge Proprietary Gauge (Ag Leader map screen) GREEN Indicates that the NH3 being applied is in a liquid state. RED Indicates that the NH3 being applied is in a vapor state. In order to determine what the state of the NH3 is in, the ISO liquid module uses both the current system pressure and temperature. Low tank pressure could result in the NH3 being in a vapor state, as well as high ambient temperatures could result in the NH3 being in a vapor state.
Hagie STS/DTS (2018 & Newer)
Hagie STS/DTS (2018 & Newer) ISO Liquid Kit PN: 2006486 REV. B Table of Contents Introduction... 3 Important Information... 3 Preliminary Installation Requirements... 3 Trademark... 3 Technical Support...
More informationEchoSonic II Ultrasonic Level Transmitter LU23, LU28 & LU29 Series Quick Start NEMA 4X Enclosure
EchoSonic II Ultrasonic Level Transmitter LU23, LU28 & LU29 Series Quick Start NEMA 4X Enclosure QS300480 Rev B 2013 Flowline, Inc. All Rights Reserved Made in USA 10500 Humbolt Street, Los Alamitos, CA
More informationUNIVERSAL PNEUMATIC TRANSDUCER FEATURES
UNIVERSAL PNEUMATIC TRANSDUCER FEATURES Non-bleed device (no air consumption in steady state) 3-15 PSI adjustable. Internal accurate closed loop control Optional pressure feedback signal Jumper selectable
More informationCurrent Loop Interface Module M-2025C
CONTROLS Interface Module M-2025C Current-to-Voltage Analog Converter used with the M-2001 Series Digital Tapchanger Control and M-2948/M-2949 Tap Position Sensors to provide positive tap position knowledge
More informationInstallation & Operation Manual
The eco-friendly solution to hard water SB-1200, SB-2000, SB-2800, SB-3600 & SB-4000 Installation & Operation Manual 10/13 Industrial Electronic Descaler 120/240 VAC (Auto Selected) Table of Contents Section
More informationTemp / RH / CO 2 Hand-Held Meter
Temp / RH / CO 2 Hand-Held Meter PRODUCT MANUAL Item # 3440 CONTENTS Specifications 2 Battery 3 LCD Display 3 Keypad 3 Operation 4 Troubleshooting 7 Warranty 8 CE Declaration of Conformity 8 Thank you
More informationInductive Conductivity Meter ILM
1 Product Information ILM-2 ILM-3 Inductive Conductivity Meter ILM f o o d Application / Specified Usage Authorizations Inductive measurement of the specific conductivity of liquid media in the range of
More information* * APPLICABLE MODELS: 2014 > MAZDA 3
PART NUMBER: 0000 8C L46 GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0604-000* APPLICABLE MODELS: 204 > MAZDA 3 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage Chart MIRROR ASSEMBLY: Mirror
More informationRCM Telemetry Instructions V2.0
Summary: RCM Telemetry Instructions V2.0 The RCM Telemetry System comprises five parts - Mobile App/Gateway/Collector/GPS/sensor. The system collects and records real-time telemetry data as you drive.
More informationKENCO Loop Powered Magnetostrictive Transmitter. KMD SERIES Operation and Installation Manual. Table of Contents
KENCO ENGINEERING COMPANY P.O. BOX 470426, TULSA, OK 74147-0426 PHONE: (918) 663-4406 FAX: (918) 663-4480 http://www.kenco-eng.com e-mail: info@kenco-eng.com KENCO Loop Powered Magnetostrictive Transmitter
More informationInstallation, Operation and Maintenance Manual
TM M723 Rev. C Model 1050 Strain Gage Transmitter Installation, Operation and Maintenance Manual Table of Contents General... 1 Installation... 1 Specifications... 1 Wiring... 2 Setup and Operation...
More informationEchoSonic II Ultrasonic Level Transmitter LU27 Series Quick Start NEMA 4X Enclosure
EchoSonic II Ultrasonic Level Transmitter LU27 Series Quick Start NEMA 4X Enclosure QS300116 Rev C 2013 Flowline, Inc. All Rights Reserved Made in USA 10500 Humbolt Street, Los Alamitos, CA 90720 USA Tel:
More informationEndress Hauser. SmarTec M CLD 133 Conductivity Measurement
Technical Information / Operating Instructions TI 281C/07/en/08.02 No. 51506567 SmarTec M Conductivity Measurement Compact conductivity transmitter with inductive sensor and integrated temperature compensation
More informationUser s Manual. F2 Calculator. A metering component for thermal energy applications
User s Manual F2 Calculator A metering component for thermal energy applications Rev 08.24.2007 1 Installation 1.1 At delivery F2 calculators are delivered in the Transport Mode. Only the clock is active
More informationFluke199XRAY. Users Manual. Medical ScopeMeter
Fluke199XRAY Medical ScopeMeter Users Manual 4822 872 30791 August 2006 2006 Fluke Corporation, All rights reserved. All product names are trademarks of their respective companies. Table of Contents Title
More informationRosemount TGU 65 Tank Radar Gauge, Still Pipe Antenna
Rosemount TGU 65 Tank Radar Gauge, Still Pipe Antenna Product Data Sheet November 2016 DS 2000-10-008 Ed 03 Rosemount TGU 65 Tank Radar Gauge, Still Pipe Antenna is a marine pipe guided level gauge that
More informationCode. Edition 04/2013. CPA Screw Air Compressors. Parts List Book
Code 2205 1084 06 Edition 04/2013 CPA7.5-10-15-20 Screw Air Compressors Parts List Book REF. PART NUM. QTY. NAME REF. PART NUM. QTY. NAME 1095 2205 1020 83 1 BASE 1195 2205 1053 83 1 PANEL 1100 2205 1028
More information+GF+ SIGNET Temperature Transmitter Instructions
GF SIGNET 80- Temperature Transmitter Instructions ENGLISH -80.090- B-/00 English CAUTION! Remove power to unit before wiring input and output connections. Follow instructions carefully to avoid personal
More informationMESA-HPX. Assembly and Installation Manual. w/appendix A for Prodelin Antenna. 901-Manual-MESA-HPX
MESA-HPX Assembly and Installation Manual w/appendix A for Prodelin Antenna 901-Manual-MESA-HPX Rev 30 March 2011 2 INDEX Installation Cautions 4 Installation Pole Height Orientation of the Mount on the
More informationDecember 2014 Ed 21. Testing and Recalibration
Testing and Recalibration Testing and Recalibration of the MAS2600 37 MAS2600: Testing and Recalibration Ed 21 December 2014 Testing Before dispatch, the MAS2600 transmitter is calibrated in accordance
More informationGrovePi Temp-Humidity Sensor Lesson Video Script. Slide 1
Slide 1 Grove Pi Temp-Humidity Lesson In this GrovePi lesson we will Kick it up with a Temperature-Humidity sensor. A temperature-humidity sensor is used to detect temperature and to detect humidity level
More informationSignet 9900 Transmitter
Signet 9900 Transmitter Member of the SmartPro Family of Instruments Features Panel Mount Field Mount Multi-Parameter input selection Large auto-sensing backlit display with at a glance visibility Dial-type
More information1: Introduction : Caution : Tips for Reading this Manual : Preface : System Highlights : Receiver
1: Introduction....1 1 2: Caution.... 2 2 3: Tips for Reading this Manual....3 3 4: Preface....4 4 5: System Highlights....6 6 6: Receiver..7 7 6.1: Specifications......7 7 6.2: Receiver Operation... 7
More informationElectromagnetic Flow Transmitter
Electromagnetic Flow Transmitter Sensor in solid state technology Working as a transmitter and/or as an On/Off controller Automatic-calibration of full scale: Teach-In Clean in place (CIP) Type can be
More informationTeacher s Guide - Activity P51: LR Circuit (Power Output, Voltage Sensor)
Teacher s Guide - Activity P51: LR Circuit (Power Output, Voltage Sensor) Concept DataStudio ScienceWorkshop (Mac) ScienceWorkshop (Win) Circuits P51 LR Circuit.DS (See end of activity) (See end of activity)
More informationTI25 - Pre-Instructional Survey
TI25 - Pre-Instructional Survey Name: Date: 1. Scheduled maintenance that is planned, with materials on hand, personnel on site, and production planning advised is called maintenance. a. predictive b.
More informationThis manual applies to the WT-RC-Ex receiver when used to locate all makes and models of 22 Hz and Wavetrak coded transmitters.
This manual applies to the WT-RC-Ex receiver when used to locate all makes and models of 22 Hz and Wavetrak coded transmitters. The Wavetrak WT-RC-Ex receiver kit comes with the following pieces of equipment:
More informationUser's Guide. Pinless Moisture/Humidity Meter with IR Thermometer + Bluetooth. Model MO297
User's Guide 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Pinless Moisture/Humidity Meter with IR Thermometer + Bluetooth Model
More informationZVS Power Resonator. CRO-SM1 Ultra Compact Self Resonating Power Oscillator
ZVS Power Resonator CRO-SM1 Ultra Compact Self Resonating Power Oscillator Features and Specifications Automatic Resonance, no tuning needed Wide supply voltage range (12V 30V) ZVS (Zero Voltage Switching)
More informationCurrent Loop Interface Module M 2025D
CONTROLS Current Loop Interface Module M 2025D Current-to-Voltage Analog Converter used with the M 2001 Series Digital Tapchanger Control and M-2948 Tap Position Sensors to provide positive tap position
More informationPSI Temperature Scanners
Networkable Voltage & Temperature Instruments Withstand 30 g and 160 db Smart Connector with Auto Sensor Discovery NetScanner Compatible DESCRIPTION The PSI 9146 and 9046-S are networkable instruments
More informationCalibration Instruction Manual Emerson 475 Field Communicator. Manual Revision FC.2
Calibration Instruction Manual Emerson 475 Field Communicator Manual Revision FC.2 ABM 2 Wire Radar with HART ABM Sensor Technologies Inc 2013, all rights reserved. Emerson is a registered trademark of
More informationVOLTAGE. User Guide ACCESSORIES. External Sensor DT140. for MicroLog EC600 and EC V ±0.05V ±3% (before calibration)
External Sensor VOLTAGE DT140 Range: Resolution: Accuracy: Input impedance: Calibration: OV protection: 0-10V ±0.05V ±3% (before calibration) 3MΩ 2 calibration points ±30V ACCESSORIES User Guide for MicroLog
More informationAUTO CAL II PO Box Sta Safety Road Houma, LA Tel # Fax #
AUTO CAL II PO Box 10083 Sta. 1 233 Safety Road Houma, LA 70363 Tel # 985-868-1477 Fax # 985-879-1617 e-mail - autocalflow@aol.com www.autocalflow.com Operating Instructions American System SW 1 SW 2 SW
More informationDual Boom ASC Set-up
Dual Boom ASC Set-up The Dual Boom ASC can be run with either the X30 or the X35. The compatible software versions for this on each monitor are 3.24.508 on the X30 and 4.01.508 on the X35. If you need
More informationCURRENT. User Guide ACCESSORIES. External Sensor DT139. for MicroLog EC600 and EC mA ±0.1mA ±3% (before calibration)
External Sensor CURRENT DT139 Range: Resolution: Accuracy: Input impedance: Calibration: OV protection: 0-20mA ±0.1mA ±3% (before calibration) ~170Ω 2 calibration points ±55mA ACCESSORIES User Guide for
More informationLT3000 ULTRASONIC LEVEL TRANSMITTER
LT3000 ULTRASONIC LEVEL TRANSMITTER Owner s Manual Specifications Installation Calibration Troubleshooting Warranty Drawings Distributed By: iprocessmart.com 14262 Doolittle Drive San Leandro, CA 94577
More informationTRACEABLE RADIO-SIGNAL REMOTE THERMOMETER INSTRUCTIONS
TRACEABLE RADIO-SIGNAL REMOTE THERMOMETER INSTRUCTIONS SPECIFICATIONS Display Main unit: two-line 1" LCD Remote unit: 3 /8" LCD Temperature Main unit IN range: 9.9 to 158.0 F ( 9.9 to 70.0 C) Main unit
More informationRCM DIRECT READING FLOWMETER
RCM DIRECT READING FLOWMETER Flow Pressure Level Temperature measurement monitoring control Special Features Compact Design Easy to Install For Horizontal or Vertical Pipes Rugged Construction Accuracy:
More informationDial-type digital bar graph. LEDs for Open Collector, Relays and Warning Indicator
Specifications General Input Channels One Input Types Digital (S 3 L) Serial ASCII, TTL level, 9600 bps Frequency Range 0.5 to 1500 Hz Accuracy 0.5% of reading Measurement Types Flow, ph/orp, Conductivity/Resis
More informationExperiment P55: Light Intensity vs. Position (Light Sensor, Motion Sensor)
PASCO scientific Vol. 2 Physics Lab Manual: P55-1 Experiment P55: (Light Sensor, Motion Sensor) Concept Time SW Interface Macintosh file Windows file illuminance 30 m 500/700 P55 Light vs. Position P55_LTVM.SWS
More informationInstallation of Fillmaster DuraBlue Melters. System on. Introduction. Instruction Sheet P/N B
Instruction Sheet P/N 1047806B Installation of Fillmaster DuraBlue Melters System on WARNING: Allow only personnel with appropriate training and experience to operate or service the equipment. The use
More informationInstruction Manual. Ultrasonic and Radar
Instruction Manual ABM Gateway Software for 3 & 4 wire Ultrasonic and Radar Instruction Manual Revision 5.8 NOTE: Windows 7 and 8 users are asked to use default screen size (100%). To change from Larger
More information8000 SERIES PRECISION MULTIMETER VERIFICATION AND ADJUSTMENT GUIDE
8000 SERIES PRECISION MULTIMETER VERIFICATION AND ADJUSTMENT GUIDE TRANSMILLE LTD. Version 1.1 : Apr 2015 TABLE OF CONTENTS PREPARING FOR CALIBRATION... 4 INTRODUCTION... 4 CALIBRATION INTERVAL SELECTION...
More informationOPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS MEMFLO MFT2 2-WIRE FLOW TRANSMITTER (877) 356-5463 (p) 330-331-7331 (f) 330-331-7172 www.flo-corp.com 2017 FLO-CORP REVA 1116 1 DESCRIPTION Please read carefully! No liability can
More informationIE-35 & IE-45 RT-60 Manual October, RT 60 Manual. for the IE-35 & IE-45. Copyright 2007 Ivie Technologies Inc. Lehi, UT. Printed in U.S.A.
October, 2007 RT 60 Manual for the IE-35 & IE-45 Copyright 2007 Ivie Technologies Inc. Lehi, UT Printed in U.S.A. Introduction and Theory of RT60 Measurements In theory, reverberation measurements seem
More informationIlluminati Wireless Light and Color Meter Model IM100. User Manual
Illuminati Wireless Light and Color Meter Model IM100 User Manual About the IM100 The Illuminati IM100 is the world s first Bluetooth-enabled wireless light and color meter. Use it with your smartphone
More informationSignet 9900 Transmitter
Signet 9900 Transmitter Member of the SmartPro Family of Instruments Features Panel Mount Field Mount Multi-Parameter input selection Large auto-sensing backlit display with at a glance visibility Dial-type
More informationInstallation guide 873 SmartRadar Control Unit & Antenna Unit
Installation guide 873 SmartRadar Control Unit & Antenna Unit Rev. 7 January 2006 Part no. 4416.569 Enraf BV PO Box 812 2600 AV Delft Netherlands Tel. : +31 15 2701 100 Fax : +31 15 2701 111 E-mail : info@enraf.nl
More informationQuantum LX Temperature Input Signal Testing
The Quantum LX control panel is capable of reading external analog devices, such as temperature sensors called ICTD s (Integrated Circuit Temperature Devices). It uses these input signals for the purpose
More informationPGS20/42 Series Grippers
PGS20/42 Series Grippers User instructions for PGS20/42 Series Grippers Engineering GREAT Solutions 12680UI Table of contents Section Page Scope...I...3 Applicable Documents... II...3 Information & Procedures...
More informationLiquid Level Transmitter Model MC420 Analog Output
l L e v e l P l u s Liquid Level Transmitter Model MC420 Analog Output Operation and Installation Manual 550760 Revision A Table of Contents Section Page 1 INTRODUCTION 1 2 PRODUCT DESCRIPTION 2 2.1 MC420
More information4.3 Touchscreen User Manual
4.3 Touchscreen User Manual Contents 1. Temperature 1. How do I adjust the temperature at console 2. How do I use the buttons on the sensor (Digital Sensor Only) 3. Sensor Symbols Explained (Digital Sensor
More informationIOM. Model 1050 Strain Gage Transmitter Installation & Operation Manual. (Cage Code #1MU21)
IOM Model 1050 Strain Gage Transmitter Installation & Operation Manual (Cage Code #1MU21) Model 1050 Strain Gage Transmitter Installation & Operation Manual CONTENTS I. GENERAL...1 II. INSTALLATION...2
More informationMagnetic Inductive Flow Sensors VMI Series
Magnetic Inductive Flow Sensors VMI Series SIKA Dr.Siebert & Kühn GmbH & Co. KG Struthweg 7 9 34260 Kaufungen Germany.: +49 5605 803-0 Fax: +49 5605 803-54 e-mail: info@sika.net www.sika.net Magnetic Inductive
More informationMODEL TI196 Current Loop Meter Installation and Operation Instructions
MODEL TI196 Current Loop Meter Installation and Operation Instructions Tel: 763. 571.3121 Fax: 763. 571.0927 www.minco.com Description The Minco TI196 is a two-wire, loop-powered digital meter that accepts
More informationULTRASONIC LEVEL INDICATOR
ULTRASONIC LEVEL INDICATOR REFLEX/SCANFLEX MULTIFLEX MINIFLEX LR MICROFLEX-C TYPICAL NON-CONTACT LEVEL METER! OUTSTANDING SOFWARE MAKES HIGHLY STABLE AND RELIABLE. A WIDE RANGE OF S FROM SOLIDS TOLIQUIDS,
More informationRadar Tank Gauging for Asphalt Inventory Measurement
White Paper November 6, 2009 Radar Tank Gauging for Asphalt Inventory Measurement This document describes the correct selection of a radar tank gauge for inventory measurement and maintainability on an
More informationMagnetic Inductive Flow Sensors induq. Series VMI
Magnetic Inductive Flow Sensors induq Series VMI Free Flow! Compact - cost-effective - robust! The induq from SIKA is a trio of extremly compact, low cost, magnetic inductive fl ow sensors. This new product
More informationMV ELECTRICAL TRANSMISSION DESIGN AND CONSTRUCTION STANDARD. PART 1: GENERAL 1.01 Transformer
PART 1: GENERAL 1.01 Transformer A. This section includes liquid filled, pad mounted distribution transformers with primary voltage of 12kV or 4.16kV (The University will determine primary voltage), with
More informationRWD68U Controller. Installation and Commissioning Guide Document No October 1, Function. Application
RWD68U Controller Installation and Commissioning Guide Document No. 129-411 Function Application The RWD68U is a three-input, two-output device used to control temperature, humidity, air pressure, fluid
More informationTxBlock-USB Transmitter
Transmitter TEMPERATURE TRANSMITTER - OPERATING MANUAL V1.0x I INTRODUCTION The TxBlock-USB is a 4-20 ma 2-wire temperature transmitter for head mount, powered by the current loop. The output current is
More informationCEC VIBRATION TRANSMITTER
CEC 1-808 VIBRATION TRANSMITTER Operation & Maintenance Manual 746 Arrow Grand Circle Covina, CA 91722 United States of America Tel: (626) 938-0200 Fax: (626) 938-0202 Internet: http://www.cecvp.com E-mail:
More informationTemperature Sensor. Temperature Transmitter MPU-LCD with Display Product Information TSM and TSB FOOD SENSORS FOR FOOD AND LIFE SCIENCES.
SENSORS FOR FOOD AND LIFE SCIENCES. Product Information TSM and TSB FOOD Temperature Sensor Application/Specified usage Temperature Measurement in vessels and pipes Authorizations Application examples
More informationAgxcel GX10 Integration into Raven 440/450/540. AgXcel. GX10 Raven Integration 440/450/540 Version 2.0
Agxcel GX10 Integration into Raven 440/450/540 Installation Overview These instructions cover AgXcel Integration kit installation for Raven 440/450 Sprayer Control Systems (Raven SCS) for liquid applications.
More informationFAG PRESTO DX. FAG PRESTO-DX preliminary User Manual. FAG GRAPHIC SYSTEMS S.A. 3, rue de la Vigie CH-1003 Lausanne Switzerland
FAG PRESTO DX FAG PRESTO-DX preliminary User Manual Table of Contents Safety Instructions... 4 DECLARATION OF CONFORMITY... Erreur! Signet non défini. PRESTO DX... 5 Pass Fail Indicator... 6 RESET and
More informationYield Calibration Procedure S-Series Combines
Yield Calibration Procedure S-Series Combines Temperature and Moisture Calibrations should be completed before attempting an accurate Yield Calibration. Moisture & Yield System Moisture sensor removal
More informationDUK COMPACT ULTRASONIC FLOWMETER
DUK COMPACT ULTRASONIC FLOWMETER Flow Pressure Level Temperature Measurement Monitoring Control Measuring Ranges: 0.0- GPM to 0.6-60 GPM Accuracy: ±. % of F.S. Turndown Ratio: 0: P max : 30 PSI; T max
More informationph or ORP Transmitter
ph or ORP Transmitter Programmable outputs: two transistor and single or dual analog 4-20 ma (Process + Temp) Removable backlighted display Universal process connection Compatible with 120 mm ph/ ORP probes
More informationCombine Calibration : S Series Harvest Monitor. Accessing User Calibrations. Temperature Calibration
Combine Calibration : S Series Harvest Monitor Accessing User Calibrations 1. Go to the Diagnostics Screen from the homepage. 2. Press the user calibration soft key. 3. Select the desired user calibration
More informationRain Gauge Smart Sensor (Part # S-RGA-M002, S-RGB-M002)
(Part # S-RGA-M002, S-RGB-M002) The Rain Gauge smart sensor is designed to work with HOBO Station loggers. The smart sensor has a plug-in modular connector that allows it to be added easily to a HOBO Station.
More informationCAP ANALOG 410 INSTALLATION & OPERATION MANUAL
CAP ANALOG 410 INSTALLATION & OPERATION MANUAL An L&J Technologies Co. 5911 Butterfield Road Hillside, IL 60162 Phone: 708-236-6000 Fax: 708-236-6006 1 was started in 1976 to offer new and innovative electronic
More informationBENCHTOP PRESSURE CONTROLLER USER MANUAL
Engineering Your Success BENCHTOP PRESSURE CONTROLLER USER MANUAL Parker Hannifin Corporation Precision Fluidics Division 26 Clinton Drive Unit 103 Hollis, NH, 03049 USA Phone 603-595-1500 GENERAL DESCRIPTION
More informationMT3500 Hand-Held Engine Analyzer Safety Operation Regulations
MT3500 Hand-Held Engine Analyzer Safety Operation Regulations - 1 - Chapter One Introduction A. Notice of Usage: MT3500 Hand-Held Engine Analyzer must be operated by trained professionals, who must know
More informationOverview. Branched connection (using an o-let or saddle component) Profile (hole) cut into the pipe run. Pipe is not broken
Overview A piping component (to cut) for routed system is considered when the component is placed onto a pipe run and a profile cut occurs in the pipe route at the inserted point. See Content Center Piping
More informationFlow Measurement SITRANS F US Inline
Flowmeter SITRANS FUS80 standard Overview Design The -path design of SITRANS FUS80 ensures maximum accuracy under short inlet conditions. The flowmeter consists of a flow sensor pipe, 4 transducers/transducer
More informationAA-35 ZOOM. RigExpert. User s manual. Antenna and cable analyzer
AA-35 ZOOM Antenna and cable analyzer RigExpert User s manual . Table of contents Introduction Operating the AA-35 ZOOM First time use Main menu Multifunctional keys Connecting to your antenna SWR chart
More informationMulti-Electrode Mounting (used for ph, Orp and Specific Ion) Honeywell Proprietary
Page: AE-7 Series 7773 Model Selection Guide Meredian Electrode with Price Data Multi-Electrode Mounting (used for ph, Orp and Specific Ion) Honeywell Proprietary Model Selection Guide 51-52-16-33 Issue
More informationUSER GUIDE Third Generation For Android and ios
USER GUIDE Third Generation For Android and ios FLIR ONE PRO USER GUIDE The FLIR ONE Pro allows you to see the world in a whole new way, with a unique blend of thermal and visible imaging. This User Guide
More informationKotron Sentinel Model 804 RF Level Transmitter
Kotron Sentinel Model 804 RF Level Transmitter D E S C R I P T I O N The Sentinel is a unique, powerful level transmitter. The leading-edge microprocessor-based circuitry has nonvolatile memory. The display
More informationBATAILG TAIL GAS ANALYZER. Rev. 1.1
BATAILG TAIL GAS ANALYZER Rev. 1.1 The Tail Gas Analyzer is part of the BAGGI BASE Instruments Series. They are the result of combining the latest state-of-the-art-technology with over 60 years of industry
More informationPower Meter. Measurement Guide. for Anritsu RF and Microwave Handheld Instruments BTS Master Site Master Spectrum Master Cell Master
Measurement Guide Power Meter for Anritsu RF and Microwave Handheld Instruments BTS Master Site Master Spectrum Master Cell Master Power Meter Option 29 High Accuracy Power Meter Option 19 Inline Peak
More informationQuick Draw Electronics. Shooting Sports Timer II User Manual. Model TS1001
Quick Draw Electronics Shooting Sports Timer II User Manual Model TS1001 Rev. F Feb 2014 WELCOME TO THE QUICKDRAW ELECTRONICS SHOOTING SPORT TIMER. THE BASIC SYSTEM CONSISTS OF; 2 IMPACT SENSORS 2 LIGHT
More informationPressure transmitter AKS 32 and AKS 33
Data sheet Pressure transmitter AKS 32 and AKS 33 AKS 32 and AKS 33 are pressure transmitters that measure a pressure and convert the measured value to a standard signal: y 1 5 V DC or 0 10 V DC for AKS
More informationDUAL OUTPUT AC CURRENT/VOLTAGE TRANSDUCER
OPERATOR S MANUAL DUAL OUTPUT AC CURRENT/VOLTAGE TRANSDUCER Masibus Automation & Instrumentation Pvt. Ltd. B/30, GIDC Electronics Estate, Sector-25, Gandhinagar-382044, Gujarat, India Web Site: www..com
More informationGENUINE ACCESSORIES INSTALLATION INSTRUCTIONS. ITEM QTY DESCRIPTION Usage Chart
PART NUMBER: 0000 8C R0 GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0554-000* APPLICABLE MODELS: 203 > CX-5 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage Chart MIRROR ASSEMBLY: Mirror
More informationDigital flow ELEMENT transmitter for continuous flow measurement
ELEMENT Transmitter Digital flow ELEMENT transmitter for continuous flow measurement Type can be combined with... PN10, DN15 to DN400 fluidic process connection Programmable outputs : one or two transistor
More informationFLOMID FX Electromagnetic Flowmeter
FLOMID FX Electromagnetic Flowmeter Working pressure manufacturing according to PED 97/23/CE (Lloyd s Register Certificate Nº 031) Introduction Modular design in two versions: Compact, sensor and electronics
More informationSignet 9900 Transmitter
Signet 9900 Transmitter Member of the SmartPro Family of Instruments Features Multiple sensor types supported with one instrument Dial-type digital bar graph Modules are field installable and replaceable
More informationFOSTEN AUTOMATION SÉRIE F500-RD
FOSTEN AUTOMATION SÉRIE Guided Wave Radar Level Transmitter Guided wave radar level transmitter. Low maintenance, auto calibrated references. Easy installation, directly in tanks or auxiliary vessels.
More informationHow to Setup and Use an Oscilloscope
How to Setup and Use an Oscilloscope An oscilloscope is a device that is used to measure voltage with respect to time. Oscilloscopes are essential pieces of test equipment used in the development and testing
More informationIAA100/IAA200 Analog Amplifiers Voltage/Current
Quick Start Guide IAA100/IAA200 Analog Amplifiers Voltage/Current Sensor Solutions Source Load Torque Pressure Multi-Axis Calibration Instruments Software www.futek.com Getting Help TECHNICAL SUPPORT For
More informationACCU-GOLD QUICK START MANUAL
ACCU-GOLD Now includes support for the light sensor (AGLS) and Accu Gold+ digitizers and sensors (AGDM+, AGMS DM+) Nomenclature AGDM Accu-Gold Digitizer Module RGDM Rapid-Gold Digitizer Module RGDM-MA
More informationSERIES 4000 Precision Dewpointmeters (Remote,Climatic, RS, and TRS)
SERIES 4000 Precision Dewpointmeters (Remote,Climatic, RS, and TRS) Issue May 2008 TABLE OF CONTENTS SECTION PAGE 1 INTRODUCTION 4 1.1 General 1.2 Operating Principle 4 5 1.3 Calibration 5 2 INSTRUMENT
More informationSITRANS F flowmeters SITRANS F US SONOCAL /184 Siemens FI
Overview Integration The flowmeter pulse output is often used as input for heat calculators. The range of meters enables optimum measurement of energy consumption. The analog output is used to inform the
More informationKotron Sentinel Model 804 RF Level Transmitter
Kotron Sentinel Model 804 RF Level Transmitter D E S C R I P T I O N The Sentinel is a unique, powerful level transmitter. The leading edge microprocessor-based circuitry has nonvolatile memory. The display
More informationS600/2630 Display Combine Yield Calibration Procedure
S600/2630 Display Combine Yield Calibration Procedure Temperature and Moisture Calibrations should be completed before attempting an accurate Yield Calibration. Moisture & Yield System Moisture sensor
More informationX30 System Components
X30 System Components X30 Monitor - Monitor is 12.1 inches - LINUX operating system not windows - Can-based communication. No serial ports - New part number 3132-10 Note: please follow the shut down procedure
More informationPrecision Thermistor Sensors
Precision Thermistor Sensors For Laboratory Applications ON-400 Series U For Use in Laboratory or Other High-Accuracy Applications U Rugged Construction Can Be Used for Short Term Water and Soil Readings
More informationDirectCommand TM Spreader
Create Configuration Application Start of Configuration Wizard Enter Settings Configuration Application Press to Highlight Configuration 4930rx calibrate fan frame feed gate Product Controller Settings
More information