ANTI - TIPPING KIT FOR CHEST, DRESSER, PLASMA/TV CHEST & NIGHTSTAND (IF OVER 30")

Size: px

Start display at page:

Download "ANTI - TIPPING KIT FOR CHEST, DRESSER, PLASMA/TV CHEST & NIGHTSTAND (IF OVER 30")"

Janel Richards
5 years ago
Views:

1 ANT - TPPN T OR EST, RESSER, PASMA/TV EST & NTSTAN ( OVER 0") This Tip Restraint Must e Attached To A Wall Stud Using ong Screw Enclosed ARWARE.... Short screw ong screw able tie racket STEP Attach a bracket securely to the back top rail of the casegoods using short screw provided, through the smaller hole. pc pc pc pcs NTSTAN ( OVER 0") EST RESSER PASMA / TV EST STEP ocate the other bracket on the wall over a wall stud and two inches below the mounting bracket secured to the back of casegoods. Attached to the wall stud using the long screw provided, through the smaller hole. STEP Place the casegoods into position so both mounting brackets are vertically in line. ace the end of the restraint strap through the larger hole in each mounting bracket. ring both ends together and slide the flat end through the locking end and draw it through until all slack is removed. onfirm that the strap is securely laced and locked. wall wall

2 MOE : MRR-077A + SRA-077A ASSEMY TPS : REVSON : A omponent ist A Mirror resser Mirror Support. Remove hardware from box and sort by size.. Please check to see that all hardware and parts are present prior to start of assembly.. Please follow attached instructions in the same sequence as numbered to assure fast and easy assembly. STEP Attach mirror support to the mirror back, then tighten with screw. Make sure the marking line on mirror support is at the same level as the bottom of mirror. ardware ist P Screw M x mm 0 A STEP Place the mirror with support on the top of dresser. Then align center as shown and tighten with screw. enter mark ASSEMY OMPETE

3 MOE : R SRR-077E + WR-077A REVSON : A ASSEMY TPS :. Remove hardware from box and sort by size.. Please check to see that all hardware and parts are present prior to start of assembly.. Please follow attached instructions in the same sequence as numbered to assure fast and easy assembly. omponent ist eadboard & ootboard A eadboard Panel E eadboard eg eft () eadboard eg Right (R) ootboard Panel Slat over rawer Slat rawer Slat Support ed Slat oles ed Slat oles 0 ed Slat Support ardware ist n eadboard & ootboard Screw M x 0mm Spring Washer Ø/" lat Washer Ø/" x mm ey M x 5mm 5 ey M5 x 5mm S M x mm 7 S M x mm 8 Screw M x 50mm 0 Side Rail ed Rail enter Slat With oles M rawer rawer Page of

4 A STEP "R" Marking behind the eadboard & eg "" Marking behind the eadboard & eg A 5 STEP Page of

5 'T' Runner 'T' Runner (Turn the 'T' runner towards the drawer slat.) STEP STEP STEP Adjust the adjuster until the drawer closes tightly. M STEP 8 STEP After insert the drawer please fasten the T-Runner on the drawer slat with screw. STEP 7 Page of

6 7 8 STEP 9 STEP Adjust leveler to touch the floor. STEP 0 E STEP nsert the tip of slat cover on the back of the footboard until closely. (*Put the cover's tip on the top of wooden cleat). STEP asten the slat cover using screws. Page of

7 MOE : R SRR-077E + WR-077A REVSON : A ASSEMY TPS :. Remove hardware from box and sort by size.. Please check to see that all hardware and parts are present prior to start of assembly.. Please follow attached instructions in the same sequence as numbered to assure fast and easy assembly. omponent ist eadboard & ootboard A eadboard Panel E eadboard eg eft () eadboard eg Right (R) ootboard Panel Slat over rawer Slat rawer Slat Support ed Slat oles ed Slat oles 0 ed Slat Support ardware ist n eadboard & ootboard Screw M x 0mm Spring Washer Ø/" lat Washer Ø/" x mm ey M x 5mm 5 ey M5 x 5mm S M x mm 7 S M x mm 8 Screw M x 50mm 7 0 Side Rail ed Rail enter Slat With oles M rawer rawer Page of

8 A STEP "R" Marking behind the eadboard & eg "" Marking behind the eadboard & eg A 5 STEP Page of

9 'T' Runner 'T' Runner (Turn the 'T' runner towards the drawer slat.) STEP STEP STEP Adjust the adjuster until the drawer closes tightly. M STEP 8 STEP After insert the drawer please fasten the T-Runner on the drawer slat with screw. STEP 7 Page of

10 7 8 STEP STEP 9 Adjust leveler to touch the floor. STEP 0 E STEP nsert the tip of slat cover on the back of the footboard until closely. (*Put the cover's tip on the top of wooden cleat). STEP asten the slat cover using screws. Page of

11 MOE : QR QSRR-077E + QWR-077A REVSON : A ASSEMY TPS :. Remove hardware from box and sort by size.. Please check to see that all hardware and parts are present prior to start of assembly.. Please follow attached instructions in the same sequence as numbered to assure fast and easy assembly. omponent ist eadboard & ootboard A eadboard Panel E eadboard eg eft () eadboard eg Right (R) ootboard Panel Slat over rawer Slat rawer Slat Support ed Slat oles ed Slat oles 0 ed Slat Support ardware ist n eadboard & ootboard Screw M x 0mm Spring Washer Ø/" lat Washer Ø/" x mm ey M x 5mm 5 ey M5 x 5mm S M x mm 7 S M x mm 8 Screw M x 50mm 0 Side Rail ed Rail enter Slat With oles M rawer rawer Page of

12 A STEP "R" Marking behind the eadboard & eg "" Marking behind the eadboard & eg A 5 STEP Page of

13 'T' Runner 'T' Runner (Turn the 'T' runner towards the drawer slat.) STEP STEP STEP Adjust the adjuster until the drawer closes tightly. M STEP 8 STEP After insert the drawer please fasten the T-Runner on the drawer slat with screw. STEP 7 Page of

14 7 8 STEP STEP 9 Adjust leveler to touch the floor. STEP 0 E STEP nsert the tip of slat cover on the back of the footboard until closely. (*Put the cover's tip on the top of wooden cleat). STEP asten the slat cover using screws. Page of

Assembly Instruction Item No. : HF SKU No. : Description: 48IN CHERRY CORNER FIREPLACE

Assembly Instruction Item No. : HF SKU No. : Description: 48IN CHERRY CORNER FIREPLACE ssembly Instruction Item No. : H170192 SKU No. : 810392478 Description: 48IN HRRY ORNR IRPL Option Option To prevent serious injury or death, this product is equipped with a wall anchoring system. efore