METROPOLIS S2S MANUAL METROPOLIS COMBI I METROPOLIS MEETING TABLE

Transcription

1 METROPOLI 2 MANUAL METROPOLI COMBI I METROPOLI MEETING TABLE

2 COMBI LEG 2 Allen Key 5mm pring Washer x M6 x mm Cap crew x M6 x 6mm Fix connection beam to legs. Hook in connection beam cover. Complete look for combi leg. FRAME 2 stabilization bar - Fix stabilization bar to connection beam. stabilization bar - Complete look for stabilization bar.

3 FRAME x-beam - Mount x-beam to the end legs. x-beam - Complete look for x-beams cluster of 2 combi desk. 5 a. b. 6 a. b. x-beam - Complete look for x-beams meeting table. 7 Hexagon rod - lot in a.hexagon outside to the end legs, b. slot in hexagon stopper for end legs 8 Hexagon rod - lot in hexagon inside to hexagon outside with the same distance for all end legs. Hexagon rod - Hexagon inside should be stop at hexagon stopper for all end legs. 2

4 FRAME Top view of hexagon rod 9 0 Hexagon rod - lot in hexagon inside to hexagon outside with the same distance for all end legs. Complete look for hexagon rods cluster of 2 combi desk. Complete look for hexagon rods meeting table. *For the middle combi share leg use only 2pcs of hexagon outside instead of pcs. CABLE TRAY 2 Place cable tray bottom on top of stabilization bar. Place cable tray cover on top of cable tray bottom.

5 CABLE TRAY Complete look for cable tray cluster of 2 combi desk. WORKTOP Allen Key 5mm 2 JCBC crew x 6 M8 x 6mm Place worktop on frame. Cluster of 2 - Attach worktops with JCBC screws from bottom of top supports for all end legs. Allen Key 5mm JCBC crew x 2 M8 x 6mm Place worktop on frame. Meeting table - Attach worktops with JCBC screws from bottom of top supports for all end legs.

6 FIXING Allen Key mm 2 et crew x 8 x-beam - Tighten all the x-beam with set screws. Hexagon rod - Tighten all the hexgon stoppers. Complete look for Metropolis combi desk. Complete look for Metropolis meeting table. 5

7 CONTROL BOX Attention: Before starting the system, please make sure, that the operating voltage of the system conforms with the local power supply. The mains plug of the control has to be connected to a free accessible power supply. * PLUG IN - FOLLOW THE INTRUCTION BELOW. FRONT VIEW BACK VIEW H MI M2 DRIVE DRIVE 2 DIPLAY 2 /D crew x M x mm Bottom view - Fix control panel with /D screws at the bottom of the worktop. Place control box in cabletray, tidy up all the cables into the cabletray. 6

8 ETTING Memory,2,, Display Up Down 2 Up tore memory Handset Handset = 68-8cmH tart up - Turn on the main power supply before setting. Once the power is on, display flashes show 000 or ---. Up Down Press and hold the down button until the lowest position 068 is reached (show in display, stop flashing), system is ready for further programming,the maximum reachable height is 8. Memory,2,, Display Up Down tore memory Normal operation - Press and hold up or down until the desired height of the desk has been reached, the display always shows the actual height. aving preferred height - preferred heights can be saved. 5 6 Memory,2,, Display tore memory Move to the desired desk height. Press the store memory. You will see the display shows -. Press one of the memory keys,,2,,, and the number of the position height is displayed, a double click is heard at the end of memory saved. Repeat the same step of this for other preferred heights. 7

9 ETTING Memory,2,, 7 PLEAE REFER TO MARKANT 068 MOTOR CONNECTOR ET UER MANUAL FOR HEIGHT ADJUTABLE DEK FOR FURTHER HELP Moving to a saved preferred height - Press and hold one of the keys,, 2,,, the desk will moves towards to the preferred height. 8