ACCESS COVER INSTALLATION INSTRUCTIONS (Kit #601 for 2006 Honda Ridgeline)
|
|
- Jessie Pope
- 5 years ago
- Views:
Transcription
1 ACCESS COVER INSTALLATION INSTRUCTIONS (Kit #601 for 2006 Honda Ridgeline) NOTE TO INSTALLER: IMPORTANT READ BEFORE ATTEMPTING INSTALLATION. Allow extra time, up to 2 hours to install this cover. Disassembly of the box wall panels and drilling is required. When assembly is complete, the roll-up cover will set recessed down from the top of the box sides. This allows the cover to match with the height of the box behind the cab and at the tailgate. These instructions replace all of Step 1 and Step 2A of the instructions in the Access owners manual. Torx bolts T-50 remove all hooks (6 total) ILLUSTRATION 1 (passenger side) TOOLS NEEDED: a. T-50 Torx f. 1/8 Bit b. T-40 Torx g. 1/4 Bit c. Flat head screw driver h. Inch pound torque wrench d. #2 Phillips head screw driver i. 10 MM Socket e. Electric Drill j. 3/8 Socket/Wrench front box wall panel Torx bolts T-40 REMEMBER TO WEAR PROTECTIVE EYEWEAR 1. Look-up the anti-theft code for the radio on the vehicle audio system card kept with the owners manual and write down the radio station pre-sets. Disconnect the negative cable from battery. 2. Remove the tie down hooks (6 total) starting at front passenger side and driver side. Then at rear passenger side and driver side (T-50). SEE ILLUSTRATION 1. ILLUSTRATION 2 (front wall) remove screw cover at rear of bed caps with flat head screw driver Phillips screw 3. Remove the 6 torx bolts on the front box wall panel (T-40) and remove. (The top three bolts will not be reused when reassembling panel). SEE ILLUSTRATION Remove passenger bed rail cap. Use flat head screw driver to remove screw cover at rear of bed cap. Use #2 Phillips screw driver to remove screw, then slide bed rail cap back to release clips, and lift up. SEE ILLUSTRA- TION 3. Repeat procedure on driver side bed cap. ILLUSTRATION 3 (passenger side) Part No REV:B Page 1 of
2 5. Remove passenger side box wall panel, (5 torx bolts) (T-40). SEE ILLUSTRATION 4. remove the 5 torx bolts that hold side panel to box 8. Pull panel away from steel box wall and unplug light connector. SEE ILLUSTRATION 7. unplug connector ILLUSTRATION 4 ILLUSTRATION 7 6. Next, pull gently on lower portion of inside pillar until one clip lets loose. SEE ILLUSTRATION Pull on inside pillar trim and hold - then gently lift wall panel out of box. SEE ILLUSTRATION 8 & 9. ILLUSTRATION 5 pull inside pillar trim away from steel body - then gently lift rear of side wall panel up and out ILLUSTRATION 8 7. On passenger side only, locate spare tire clip. Push center of clip and pull out on panel to free clip. SEE ILLUSTRATION Repeat procedure on driver side box wall panel. (driver side does not have spare tire clip). ILLUSTRATION 6 lift rear up and away ILLUSTRATION 9 Page 2 of 6
3 (Kit #601 Cont.) NOTE: Length dimensions given are approximate. Use them to locate the 3 locations for drilling holes. drill 1/8 pilot holes 3 locations only - exactly 1/2 up from mold marks. 11. With passenger side wall panel laying backside facing up, mark three new hole locations as shown (1/2 inch above center of existing mold marks) and drill three 1/8 pilot holes into panel. SEE ILLUSTRATION 10. Repeat procedure for driver side wall panel. 28 1/ / Now, open the Roll-Up Cover kit and find the metal Z brackets (6 pcs), the flat washers, lock washers, and 6mm x 40mm hex head bolts. Install these brackets to the existing holes on the box wall with a 10mm wrench. Slotted hole in bracket should point up - insert bolt with washers in bottom hole first. NOTE: Two brackets with 2 3/8 leg belong at front of box. Attach all 6 brackets. Tighten all bolts to 100 inch pounds. SEE ILLUSTRATION 11 & 12. 1/ 2 existing marks on panel mark center location of new hole 1/2 up from center in line with existing mold marks ILLUSTRATION 10 rear - tailgate end passenger side shown with wall panel back side facing up Z bracket flat washer lock washer install end with slotted hole up 2 3 /8 front Z bracket 6mm x 40mm hex head bolt (10mm wrench) center Z bracket rear Z bracket ILLUSTRATION 11 ILLUSTRATION 12 Page 3 of 6
4 13. Re-install both sidewall panels, reconnect light plug connectors. Re-connect the negative cable to the battery and check that the cargo lights work. SEE ILLUSTRATION 13. Then insert bolts and tighten. On passenger side, push spare tire clip on. reconnect light plug Now, re-install bed caps (if bed rail caps do not align properly you may need to loosen torx bolts on wall panel and shift panel for better fit, then re-tighten bolts). push panel in and down 14. Next, set front box wall panel in position with the 3 bottom torx bolts only and tighten them. Then re-install all 6 tie-down hooks. ILLUSTRATION Locate header bar and 6mm x 40mm hex head bolts in the kit. Align holes in header bar with upper three open holes on front box wall panel. Insert replacement Hex head bolts. Tighten outer bolts to 60 inch pounds. Tighten center bolt to about 20 inch pounds. (10mm socket) SEE ILLUSTRATION 14. header bar ILLUSTRATION With a 1/8 drill bit, use previously drilled holes in sidewall panels as a guide to drill a 1/8 pilot hole into the Z brackets (that are now behind the sidewall panels) and through the sheet metal of the box wall. SEE ILLUSTRATION 15. Then drill 1/4 enlargement holes in composite layer of the wall panel. DO NOT DRILL 1/4 hole into steel Z brackets. This avoids chipping the composite panel when mounting side rails with self drilling screws. use previously drilled holes in panel (3 per side) as guide to drill pilot holes into Z brackets ILLUSTRATION 15 Page 4 of 6
5 17. Locate the cover siderails, nylon spacers and screws used to mount the rails to the box and sort them by size as shown. Align holes in the cover rail with previously drilled holes in box wall. Match the screws and spacers with the proper location. SEE ILLUSTRATION 16. passenger side rail shown nylon spacer FIRST FASTEN FRONT - use 2 1 /2 long screw with 3/4 long spacer THIRD FASTEN CENTER - use 2 1 /2 long screw with 7/8 long spacer SECOND FASTEN REAR - use 2 1 /2 long screw with 1 long spacer 18. Back of rail should rest on top of pillar at rear of box. Note nylon spacer attached to bottom of rail helps stabilize rail during install. (Leave attached to rail permanently). SEE ILLUSTRATION 17. ILLUSTRATION 16 back of rail resting on box pillar 19. First, begin at front of rail - Align pre-punched holes in rail with drilled holes in wall panel. Insert 2 1 /2 screw, use 3/4 long spacer positioned behind rail and drill screw into pilot hole of metal Z bracket. Use 3/8 socket. SEE ILLUSTRATION 16 &18. ILLUSTRATION 17 Second, go to rear of rail - install a 2 1/ 2 screw with 1 long spacer positioned behind rail and drill screw into pilot hole on Z bracket. SEE ILLUSTRATION 16 & 18. 3/8 socket Third, finish at center of rail with another 2 1/ 2 screw and a 7/8 spacer behind the rail. REPEAT PROCEDURE for driver side rail. Tighten all screws until spacer is tight -then check with torque wrench and tighten to about 40 inch pounds. Now - refer to the owners/installation manual and continue on beginning with Step 2B - Element Seal TM instructions. tighten screws until spacer is tight (approx. 40inch pounds) ILLUSTRATION 18 Page 5 of 6
6 20. Reset the clock, and reset the radio station presets. NOTE: Whenever the battery is disconnected, the driver s window AUTO function is disabled. 21. Start the engine. Push down on the driver s window switch until the window is fully open. 22. Check that the cargo lights are working. 23. Pull up on driver s window switch to close the window completely, then hold switch for two seconds or more. 24. Lower and raise window to check the operation of the driver s window AUTO function. 25. Now - refer to the Access owners/installation manual and continue on beginning with Step 2B - Element Seal TM instructions. Shown here are some helpful hints when closing the cover. Use these in conjunction with the procedures in the Access owners manual (page 5). When sealing the sides, push down on vinyl next to rail... grip and pull it snug by the edge... then push it down to seal along rail from front to back. NOTE: For best results always keep valley between box and cover clean of debris NOTE: The Honda Ridgeline is equipped with a trunk-like lid on the bed floor. The lid remains functional - although slightly restricted from fully opening with the cover. Avoid forcing the lid beyond its limit. floor storage lid open Page 6 of 6
HONDA RIDGELINE (KIT #601) Installation Instructions (to be used in addition to owners manual)
HONDA RIDGELINE (KIT #601) Installation Instructions (to be used in addition to owners manual) IMPORTANT NOTE: Read before beginning installation. These instructions replace all of Step 1 of the instructions
More informationRBP-1215B-RX DODGE RAM QUAD CAB RX3
RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side
More informationBX2173 Installation Instructions Ford Focus (including the 2.3L engine) 2003 Ford Focus SVT
BX2173 Installation Instructions 2000-04 Ford Focus (including the 2.3L engine) 2003 Ford Focus SVT Serial No. The front fascia, coolant line bracket and anti-pollution devices are removed for baseplate
More informationPlease read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment.
2005-08 Pontiac G6 GT Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed
More informationBX3230 Installation Instructions Oldsmobile Silhouette Chevy Venture
BX3230 Installation Instructions 1997-2004 Oldsmobile Silhouette 1997-2003 Chevy Venture Serial No. The headlight assembly, front fascia, horn bracket and windshield washer reservoir are removed for baseplate
More informationBOX-115 Club Car Precedent Utility Box Mounting Kit Installation Instructions
BOX-115 Club Car Precedent Utility Box Mounting Kit Installation Instructions Contents of BOX-115 Utility Box Mounting Kit: a (1 ea.) Utility Box Support Frame, Passenger Side b (1 ea.) Utility Box Support
More informationWARNING. BX Ford F350 (Includes Super Duty) Installation Instructions
Serial Number BX231 Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed
More informationINSTALLATION INSTRUCTIONS KK-K9-F14-K K9 KIT FOR FORD EXPEDITION
INSTALLATION INSTRUCTIONS KK-K9-F14-K-32 32 K9 KIT FOR 2003-2016 FORD EXPEDITION TOOLS REQUIRED: Power Drill Drill Bit Set Standard & Metric Socket Sets Phillips Screw Driver Open End Wrench Set Wire Cutters
More informationPlease read BOTH these Installation Instructions and the General Instructions before attempting to install or operate this equipment.
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who
More informationFord Raptor Venom Front Bumper Installation Instructions
PREPARATION 2010 2014 Ford Raptor Venom Front Bumper Installation Instructions 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2. We recommend
More informationBOX-117 E-Z-Go RXV Utility Box Mounting Kit Installation Instructions
BOX-117 E-Z-Go RXV Utility Box Mounting Kit Installation Instructions Contents of BOX-117 Utility Box Mounting Kit: a (1 ea.) Utility Box Support Frame, Driver Side b (1 ea.) Utility Box Support Frame,
More informationInstallation Instructions Kit, Base Rail Bracket Part # 31413
Installation Instructions Kit, Base Rail Bracket Part # 31413 Dealer / Installer: Provide a copy of these Instructions to the end user of this product. These Instructions provide important operating and
More informationC4 Fabrication Rock Slider Installation 14+ 5th Gen 4Runner w/o KDSS
C4 Fabrication Rock Slider Installation 14+ 5th Gen 4Runner w/o KDSS Thank you for your purchase of the C4 Fabrication s 5th Gen 4Runner Rock Sliders! This product was carefully crafted to ensure a perfect
More informationRH-412 STEEL DOORS INSTALLATION INSTRUCTIONS
RH-412 STEEL DOORS INSTALLATION INSTRUCTIONS By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side.
More informationBX1965 Installation Instructions 2004 Chrysler Sebring Convertible
BX1965 Installation Instructions 2004 Chrysler Sebring Convertible Serial No. The headlight assembly, front fascia, horn bracket and windshield washer reservoir are removed for baseplate installation.
More informationINSTALLATION INSTRUCTIONS RH 412 STEEL DOORS
By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side. Note: Having the hood open makes the job
More informationPlease read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment.
Serial Number Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed
More information2015 Current Ford F150/Raptor Adaptive Cruise Control Module Relocation Bracket Installation Instructions
2015 Current Ford F150/Raptor Adaptive Cruise Control Module Relocation Bracket Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground
More informationWARNING. BX Ford Explorer With Adaptive Cruise Control & Eco Boost Installation Instructions
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who
More informationPlease read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment.
Serial Number 2012 Hyundai Accent (No Foglights) Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
Attachment Tab Height: 13 Attachment Tab Width: 24 Please read BOTH these and the General Instructions prior to installing or operating this equipment. Serial Number 1. Blue Ox towing products and accessories
More informationWARNING. Baseplates Honda Pilot 2002 Acura MDX Installation Instructions BX2227. Serial Number
Baseplates BX2227 03-05 Honda Pilot Please read BOTH these and the General Instructions before attempting to install or operate this equipment. Serial Number 1. Blue Ox towing products and accessories
More informationWARNING VW Jetta New Installation Instructions BX3823. Serial Number
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. Serial Number 1. Blue Ox towing products and accessories are intended to be installed by Blue
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who are familiar
More informationWARNING Honda Civic (Incl. EX, LX, DX) Installation Instructions BX2243. Serial Number
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. Serial Number 1. Blue Ox towing products and accessories are intended to be installed by Blue
More informationINS T A L L A TIO N INS T R U C TIO N S. Ceiling Mount Track System
Ceiling Mount Track System 10.26.2016 Specifications Ceiling Post: Unassembled 2-7/8 Assembled 1-11/16 7/8 7-9/16 5-7/8 3/8 2 Tubes 1/2 2-3/8 5 Parts and Tools Tools Needed Tape Measure Pencil Drill with
More informationADDICTIVE DESERT DESIGNS
Preparation: Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake. We recommend reading through the installation instructions in whole before performing
More informationBX2520 Installation Instructions 2004 Mazda 3
BX2520 Installation Instructions 2004 Mazda 3 Serial No. The headlight assembly, front fascia, horn bracket and windshield washer reservoir are removed for baseplate installation. Drilling is required.
More informationBOX-118 E-Z-Go TXT Utility Box Mounting Kit Installation Instructions
BOX-118 E-Z-Go TXT Utility Box Mounting Kit Installation Instructions Contents of BOX-118 Utility Box Mounting Kit: a (1 ea.) Utility Box Support Frame, Driver Side b (1 ea.) Utility Box Support Frame,
More informationBY ALIEN TECHNOLOGIES CORP
BY ALIEN TECHNOLOGIES CORP Assembly Instructions TopLift Pros YOU MAY ALSO REVIEW OUR ASSEMBLY VIDEO, PLAY AND PAUSE AT YOUR CONVENIENCE. JUST VISIT US AT WWW.TOPLIFTPROS.COM AND GO TO Customer Support
More informationADDICTIVE DESERT DESIGNS
Preparation: Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake. We recommend reading through the installation instructions in whole before performing
More informationWARNING Honda Civic (Incl. EX, LX, DX) Installation Instructions BX2243. Serial Number
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. Serial Number 1. Blue Ox towing products and accessories are intended to be installed by Blue
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
Attachment Tab Height: 16-1/2 Serial Number Attachment Tab Width: 24 Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products and
More informationINSTALLATION MANUAL WEEKENDER STEEL LADDER RACK
TRUCK STORAGE SOLUTIONS SECURING YOUR REPUTATION INSTALLATION MANUAL WEEKENDER STEEL LADDER RACK STEEL & ALUMINUM SIDE BOX WITH PACK RAT DRAWER UNITS MODELS ATTENTION: PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS
More informationGRILLE GUARD SPRINTER VAN (EXCLUDES X4) INCLUDES MERCEDES, FREIGHTLINER AND DODGE PARTS LIST:
PARTS LIST: 1 Grille Guard 8 12mm Hex Nuts 1 Driver/Left Side Frame Mounting Bracket 2 10-1.50mm x 25mm Button Head Bolts 1 Passenger/Right Side Frame Mounting Bracket 4 10mm x 20mm OD x 2mm Flat Washers
More informationBX Toyota Tacoma (Includes Prerunner) Installation Instructions
Attachment Tab Height: 11.5 Attachment Tab Width: 30.5" Serial Number Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products and
More information55000/55010 Installation Instructions
A. Install 55015 B. Bolt roof rails, 55020/55025, to front hoop. C. Assemble 55026 D. To install without drilling into bumper. E. If mounting directly to bumper. A. 55015 Installation Instructions 55000/55010
More informationDRAWER Mitsubishi pajero lwb
DRAWER Mitsubishi pajero lwb SSDS601 / SSMP001 INSTALL TIME: 45 mins Thank you for purchasing a Front Runner Storage System. This Storage System is made up of the following components: 1. A Drawer System
More informationWARNING BX Toyota Matrix Toyota Matrix XRS 2007 Toyota Corolla S 2008 Toyota Matrix Installation Instructions.
Please read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment. 2005-07 Toyota Matrix 2008 Toyota Matrix Attachment Tab Height:
More informationREPLACEMENT TARP for SRT-2 SPOOL ROLL TARP
REPLACEMENT TARP for SRT-2 SPOOL ROLL TARP NOTICE TO INSTALLER: Even if familiar with product, read instructions prior to installation as improvements may be made without notice. Always handle components
More informationPlease read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment.
Serial Number BX3231 2005-08 Pontiac G6 GT Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories
More informationINSTRUCTIONS INSTRUCCIONES CONSIGNES
AUTOMOTIVE PRODUCTS, INC. INSTRUCTIONS INSTRUCCIONES CONSIGNES APPLICATION: 2007 13 CHEVY SILVERADO 1500 (except Classic ) MAX WINCH TRAY: HDX 46-22275 SPORTSMAN WINCH MOUNT GRILLE GUARD: 45-92270, 40-92275
More informationPlease read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment.
Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who are familiar
More informationINSTALLATION INSTRUCTIONS Accessory MOTORCYCLE BED P/N 08L26-SJC-100A Application 2011 RIDGELINE Publications No. AII 43440 Issue Date JUNE 2010 PARTS LIST Left tube 6 Hex bolts Right tube (with label)
More informationQueen Wingback Bed King Wingback Bed
Parts and Hardware List A. Side Rails with Attachment Hooks 2 pcs B. Foot Rail 1 pc C. Head Rail 1 pc D. Center Support Slat 1 pc E. Leg Supports 3 pcs F. Support Slats 4 pcs G. Flat Washers 8 pcs H. Lock
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
Attachment Tab Height: 16-1/4 Attachment Tab Width: 21-3/4 Please read BOTH these and the General Instructions prior to installing or operating this equipment. Serial Number 1. Blue Ox towing products
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
Attachment Tab Height: 24-3/4 Attachment Tab Width: 21 Serial Number Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products and
More informationHatchback Wing Riser Kit
Hatchback Wing Riser Kit 2015-06-11 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of aftermarket
More informationWARNING. BX Ford Explorer With Adaptive Cruise Control & Eco Boost Installation Instructions. Bolt Torque Specifications
Please read BOTH these and the General Instructions before attempting to install or operate this equipment.. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who
More informationInstallation Instructions - Model V4JSD 1
Installation Instructions - Model V4JSD 1 Support Assemblies: Parts list: (Note see enclosed cut sheet for quantities and dimensional information) A vertical structural member (1 ½ x 1 ½ modular frame)
More informationBX Honda Accord Ex-L 2012 Honda Accord SE Installation Instructions
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. Serial Number 1. Blue Ox towing products and accessories are intended to be installed by Blue
More informationBarricade Trail Force HD Rear Bumper w/ Tire Carrier installation (07-16 Wrangler JK)
Barricade Trail Force HD Rear Bumper w/ Tire Carrier installation (07-16 Wrangler JK) Installation Time: 2-3 Hours Tools Required: Tire iron Ratcheting socket set (ratchet plus 13, 16, 19mm sockets) Open
More informationUS RACK, Inc Falcon Drive, Madera, CA
US RACK, Inc. - 2850 Falcon Drive, Madera, CA 93637-559-661-3050 INSTRUCTIONS for MOTORCYCLE RACK with Cradling Wheel Chocks WARNING: Do NOT attempt to install or use this rack without following all instructions.
More informationDodge Dakota WARNING. B as e plate s. Installation Instructions BX1971. Serial Number
B as e plate s BX1971 Serial Number Attachment Tab Height: 17.5 Attachment Tab Width: 20 Please read BOTH these Installation Instructions and the General Instructions before attempting to install or operate
More informationPlease read BOTH these Installation Instructions and the General Instructions before attempting to install or operate this equipment.
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who
More informationTOYOTA TACOMA LED BED LIGHTS Preparation
Preparation Part Number: PT948-35160 Kit Contents Item # Quantity Reqd. Description 1 1 Hardware Kit 2 1 Driver Side LED assembly 3 1 Passenger Side LED assembly 4 1 Main Wire Harness Hardware Bag Contents
More informationFRAME BRACKET. Doing Our Best to Provide You the Best. Ford. Page 1. BOlT TORQUE SPECIFICATIONS HJ31000,Rev 0
2-13 HJ31000,Rev 0 Ford BOlT TORQUE SPECIFICATIONS METRIC BOlTS Size Grade Torque 8mm 8.8 23 ft/lbs. 10mm 8.8 45 ft/lbs. 12mm 8.8 78 ft/lbs. 14mm 8.8 125 ft/lbs. STANDARD BOlTS Size Grade Torque 5/16 5
More informationJK Rear Inner Fenders
INSTALLATION INSTRUCTIONS INST-17-05-080_A JK Rear Inner Fenders IMPORTANT: Thank you for purchasing this Poison Spyder product. Please read through this entire document before proceeding with installation.
More informationWARNING. B as e plate s. BX Saturn L Series Installation Instructions. Serial Number
B as e plate s BX3323 Please read BOTH these and the General Instructions before attempting to install or operate this equipment. Serial Number 1. Blue Ox towing products and accessories are intended to
More informationMedium HoneyBadger Chase Rack Installation Instructions
PREPARATION Medium HoneyBadger Chase Rack Installation Instructions 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2. We recommend reading
More informationSTYLE BAR & TONNEAU COVER INSTALLATION
STYLE BAR & TONNEAU COVER INSTALLATION INSTALLATION MANUAL: 2005 to '09 Mustang P/N: 10-8002-C12071B Saleen Performance, Inc. 1225 East Maple Rd., MI 48083 800-888-8945 www.saleen.com 1 IF YOU ARE NOT
More informationGeneral Features. Low Profile. The SMART BOXX stands only 1.5 off of the bed of your truck so cargo space is maximized
General Features Low Profile. The SMART BOXX stands only 1.5 off of the bed of your truck so cargo space is maximized Two Sizes Short Box :74 L X 47 W X 7 T and Long Box 92 L X 47 W X 7 T All Aluminium
More informationTABLE OF CONTENTS REQUIRED TOOLS
TABLE OF CONTENTS SECTION SECTION TITLE PAGE NO. 1 2 3 4 5 Assembling Mounting Structure Installing Bicycle Supports Mounting Rack to Wall Adding Sections Customizing Rack Configuration REQUIRED TOOLS
More informationSEAT-361 E-Z-Go RXV RHOX Seat Kit Installation Instructions
SEAT-361 E-Z-Go RXV RHOX Seat Kit Installation Instructions Contents of SEAT-361 RHOX 300 Series Rear Seat Kit: a (1 ea.) Front Seat Back Support, Driver Side b (1 ea.) Front Seat Back Support, Passenger
More informationWARNING Honda Pilot Installation Instructions BX2244. Serial Number
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. Serial Number 1. Blue Ox towing products and accessories are intended to be installed by Blue
More informationAssembly Instructions
Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt
More information3/4 Rear DuraRac Installation Instructions
3/4 Rear DuraRac Installation Instructions Ford Transit Low Roof 130 WB Frame Kit Part #: CRC 27-1010-001 V1.0.09.28.18 IMPORTANT INSTALLATION STEPS ARE DENOTED USING A STOP SIGN. THESE STEPS MUST BE PERFORMED
More informationN. 15th Street, Middlesboro, KY FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS
1-800-248-7717 1002 N. 15th Street, Middlesboro, KY 40965 FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Mountain Flip Tarp Dump Body tarping system. With tarping systems
More informationTIRE RACK INSTALLATION INSTRUCTIONS Dodge Sprinter
Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 TIRE RACK INSTALLATION INSTRUCTIONS 07-11 Dodge Sprinter Please read before beginning Stainless steel hardware may bind together
More informationPickup Box Utility Rack Package Installation (Instruction ID: )
017 Chevrolet Colorado Pickup - WD (VIN S) Canyon, Colorado Accessory Installation Manual N America Document ID: 3966961 Pickup Box Utility Rack Package Installation (Instruction ID:3144879) Installation
More informationBX3615. Subaru Impreza WRX (Include STI) Subaru 2012 Impreza Premium 2010 Outback Sport Installation Instructions Attachment Tab Height: 15
1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who are familiar with our products and have the equipment and knowledge necessary to do fit work. If needed, Blue
More informationB as e plate s Honda Accord (Incl. LX, EX, DX) (no foglights) BX2242. Serial Number. Installation Instructions
B as e plate s Please read BOTH these and the General Instructions before attempting to install or operate this equipment. Serial Number 1. Blue Ox towing products and accessories are intended to be installed
More informationWARNING Mercedes Benz GL550 4Matic Installation Instructions BX1992. Serial Number
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who
More information2017 Current Ford Raptor ADD Pro Front Bumper Installation Instructions
2017 Current Ford Raptor ADD Pro Front Bumper Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2.
More informationUser Instructions Multiline Otter Scoreboard Caddy Assembly
List of parts: User Instructions Multiline Otter Scoreboard Caddy Assembly Single Caddy Double Caddy 1 1 Base assembly with attached wheels 2 4 1 1 2 4 4 8 10 20 12 Uprights (60 or 74 aluminum extrusion)
More information4832A Installation Sheet Part List
4832A Installation Sheet Part List (1) 4016A-43-003 Qty 1- (2) 4016A-43-002 Qty 1- (3) 4016A-43-001 Qty 2- (4) 4016A-10-005 Qty 1- (5) 4016A-43-004L Qty 1- Mounting Bolt Kit (A) (K) Qty 2 - Qty 6 - M10
More informationIntroduction. Rocky Mountain Westy Swing Away Carrier Kit Installation Instructions
Rocky Mountain Westy Swing Away Carrier Kit Installation Instructions Introduction Thank you for purchasing the Rocky Mountain Westy Swing Away Carrier Kit. We pride ourselves in the products we develop
More informationInstallation Instructions Kit, Base Rail Bracket Part # 31413
Installation Instructions Kit, Base Rail Bracket Part # 31413 Dealer / Installer: End User: Provide a copy of these Instructions to the end user of this product. These Instructions provide important operating
More informationWARNING. BX Kia Soul Installation Instructions. Bolt Torque Specifications. Bolt Torque Specifications
Serial Number Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationWARNING Honda Civic SI Installation Instructions BX2241. Serial Number
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
Attachment Tab Height: 19-1/2 Attachment Tab Width: 19 Serial Number Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products and
More informationBulkhead Model Number and
Bulkhead Model Number 96141-3-01 and 96142-3-01 Installing your ProMaster bulkhead is very clear cut following these instructions. Before cutting or drilling in the floor, verify the location of you gas
More informationMETRIC BOlTS. Size Grade Torque 8mm ft/lbs. 10mm ft/lbs. 12mm ft/lbs. 14mm ft/lbs. 16mm ft/lbs.
8/16 HJ31005,Rev 7 BOlT TORQUE SPECIfICATIONS METRIC BOlTS STANDARD BOlTS Size Grade Torque 5/16 5 18 ft/lbs. 3/8 5 30 ft/lbs. 7/16 5 50 ft/lbs. 1/2 5 75 ft/lbs. 5/8 5 150 ft/lbs. 3/4 5 290 ft/lbs. Size
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
2012-14 Chevy Captiva Sport Attachment Tab Height: 21-1/2 Serial Number Attachment Tab Width: 18-1/2 Please read BOTH these and the General Instructions prior to installing or operating this equipment.
More informationBX1956 Installation Instructions Chrysler PT Cruiser (Include Turbo)
BX1956 Installation Instructions 2001-04 Chrysler PT Cruiser (Include Turbo) Serial No. The front fascia and metal bumper are removed for baseplate installation. Factory metal bumper will not be reinstalled.
More informationCAB END BEDTRAX (SIDE VIEW)
Supplied Hardware: (8-14) 1/4-20 Allen head bolts, (12-18) UHMW mount blocks, (4) D-ring tie downs Tools Needed: Allen head wrench GET TO IT. INSTALLATION INSTRUCTIONS STEP 1. INSERT (2) MOUNT BLOCKS INTO
More informationSB-F-MUSCPE/12TW3 SKU# Up Ford Mustang Coupe
If you choose to perform the installation yourself, it is absolutely vital that the Stealthbox be properly mounted to the vehicle according to these instructions. Failure to mount the enclosure properly
More informationContractors Rack Assembly and Installation Instructions
Part # 18601 & 16601 Contractors Rack Assembly and Installation Instructions 4751 Littlejohn St. Unit A, Baldwin Park, CA 91706 Page 1 of 12 11/13/08 Thank you for purchasing the Paramount Restyling Contractors
More informationWARNING. BX Dodge Durango. Serial Number
Please read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationLOFT DOOR HANGER BARN DOORS & HARDWARE. Hardware Installation Instructions. Page
LOFT DOOR HANGER Page 1 Specifications 2 7/16" 3/8" 1-1/2 1-3/4 Ø3 3 7/8" 11-1/16 Page 2 Parts and Tools Tools Needed Tape Measure Pencil Drill with 1/8, 1/4 and 3/8 bits, 1 spade bit and Phillips bit
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SNYPER TUBULAR FENDERS APPLICATION: 2007-2017 Jeep Wrangler JK PART NUMBER: 62-1005, 62-1015 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1,2 2 FRONT FENDERS, DRIVER (1) AND PASSENGER
More informationThor Audi A4/S4 Skid Plate Installation Instructions
Thor Audi A4/S4 Skid Plate Installation Instructions Parts List: 1 Aluminum Skid Plate 2 Aluminum Side Wings 10 10mm Flat Washers 3 8mm Flat Washers 3 8mm Speed Clips 2 10x40mm Bolts 3 8x35mm Bolts 2 Rivet-nuts
More informationInstallation for Full Size Polaris Ranger Crew Doors
Installation for Full Size Polaris Ranger Crew Doors Order of Installation: Heater Doors Wiper on to Windshield Windshield Top & Back Panel Note: Most of the steps in these instructions need to be repeated
More informationWARNING. BX Jeep Liberty Installation Instructions. Serial Number
Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers
More informationINSTALLATION INSTRUCTIONS
NOTE: Bolts should remain hand tight until all bolts are installed. STEP 1 Installing the door base (both sides). 1. Locate the outer, roll cage, mounting bolt (passenger side is shown in the illustration).
More information