ACTIV Pro3 height adjustable base Installation Guide

Transcription

1 ACTIV Pro height adjustable base Installation Guide

2 Components ACTIV-Pro Installation Guide Hard ware cable clips x 8mm 5mm 4mm allen keys screw caps x 8 center leg x center leg bracket x end leg x foot x cantilever x wood screw x handset screw x M6 x M6 (special) x 8 M0 x 8 handset x power box x frame BL x frame BR x frame FL x frame FR x stretcher bar end x stretcher bar x 4 controller cable x power cable

3 Phase Leg Attachment ACTIV-Pro Installation Guide Identify center leg Identify center Assemble leg. center leg to center bracket with M6 screws Assemble center leg to center bracket with M6 screws. Front Right, Back Right, Front Left and Back Left are indicated on Center Bracket with the initials FR, BR, FL and BL

4 Phase Attaching Stretcher Bar Match up frames to center bracket, line up holes to the degree that you are setting, and screw in M6 screws Assemble stretcher bars into the frames Match Complete up frames connecting to center the bracket, stretcher lining bars up the and holes stretcher to the bar degree ends that Assemble you are end setting legs (90 to o or the 0 stretcher o ). Screw bar in with ends M6 using screws. M6(special) screws ACTIV-Pro Installation Guide Attach stretcher bars to the frames. Note limit of stretch length and assemble base within that limitation. Complete connection of stretcher bars and stretcher bar ends. Attach end legs to the stretcher bar ends using M6 (special) screws. Note: Trim caps will be attached in Phase 4. maximum mounting distance *For 48 width worksurfaces, do not install stretcher bars. 4

5 Phase Attaching Cantilevers and Feet ACTIV-Pro Installation Guide Plug in cantilevers in the stretcher bar ends, line up holes and add screws M6(special) Tighten using #4 allen key or a long extension angle-tipped allen key to expedite the process Plug cantilevers Add trim into caps the to stretcher fill holes bar ends, lining up holes. Add screws M6 (special). Tighten using #4 allen key (or a long extension angle-tipped allen key to expedite the process). Attach feet to end legs with M0 screws Attach feet to legs with M0 screws. Note: Trim caps will be attached in Phase 4. 5

6 Adjust stretcher bars to desired length Phase 4 Adjusting Stretcher Bars Tighten 4 factory inset screws to hold the desired length in place ACTIV-Pro Installation Guide Adjust stretcher bar to desired length. Tighten 4 factory inset screws to hold desired length in place. Place caps. Make sure the screw bracket stays in the center of the stretcher bars 6

7 Phase 5 Connecting Attach the base assembly Worksurface to the worksurface& Power Ensure that the base is properly positioned to the worksurface 4 5 Attach the base to the worksurface using wood screws Attach the handset to desired location using handset screws (count x ) Ensure that the base is properly Plug positioned in electrial on according to below drawing and attach cable management clips, if desired the worksurface. Attach base Note to the : The worksurface should be centeraligned with the cantilever depth using wood screws. and should have equal amount of overhang on each end Note: The worksurface should be center aligned with the cantiliver depth and should have equal amount of overhang on each end. Attach the handset to desired location using handset screws (count x) Plug in electrical according to the diagram at right. Attach cable management clips if using. Facing Direction ACTIV-Pro Installation Guide 4 Connect each plugs according to the drawing. Orientate yourself to the table assembly by facing as user to identify left and right motor. 7

8 Phase 6 Program Height Memory Presets ACTIV-Pro Installation Guide To Program Up to 4 Presets: Use the up/down arrows to find desired height, then press M followed by the number,, or 4. To Test Programmed Height: Use the up/down arrows to adjust the table to a height other than the preset height. Then push and hold the number you programmed to see if it auto matically adjusts to the height programmed in Step. You may need to hold for - seconds to activate the base. Note: If it does not adjust to the programmed height, repeat Step followed by Step. AMQ 4 M 8

9 5 Day Open Plan we provide exceptional experiences with reliable, easy interactions and successfully fulfilled orders in only 5 days 764 Walsh Avenue / Santa Clara, CA (877) amqsolutions.com